Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “NITROGEN 15”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Decomposing Solid Micropropulsion Nozzle Performance Issues

Micropropulsion technology is essential to the success of miniaturized spacecraft and can provide ultra-precise propulsion for small spacecraft. NASA Glenn Research Center has envisioned a micropropulsion concept that utilizes decomposing solid propellants for a valveless, leak-free propulsion system. Among the technical challenges of this decomposing solid micropropulsion concept is optimization of miniature, rectangular nozzles. A number of flat micronozzles were tested with ambient-temperature nitrogen and helium gas in a vacuum facility. The thrusters were etched out of silicon and had throat widths on the order of 350 microns and throat depths on the order of 250 microns. While these were half-sections of thrusters (two would be bonded together before firing), testing provided the performance trend for nozzles of this scale and geometry. Area ratios from 1 to 25 were tested, with thrust measured using an inverted pendulum thrust stand for nitrogen flows and a torsional thrust stand for helium. In the nitrogen testing, peak nozzle performance was achieved around area ratio of 5. In the helium series, nozzle performance peaked for the smallest nozzle tested area ratio 1.5. For both gases, there was a secondary performance peak above area ratio 15. At low chamber pressures (< 1.6 atm), nitrogen provided higher nozzle performance than helium. The performance curve for helium was steeper, however, and it appeared that helium would provide better performance than nitrogen at higher chamber pressures.

Reed, Brian↗
NASA NTRS1983

Studies of flows through N-sequential orifices

Critical mass flux and axial pressure profile data for fluid nitrogen are presented for N = 20, 15, 10, and 7 N-sequential orifice inlet configurations uniformly spaced at 15.5 cm. These data correlate well over a wide range in reduced temperature (0.7 T sub r,o ambient) and reduced pressure (to P sub r = 2) and are in general agreement with studies of one to four inlets and labyrinth seal gas data for 33 tooth equivalent sequential inlets. Experimental and theoretical agreement is good for liquid and gas critical mass flux.

Hendricks, R. C.↗
NASA NTRS1983

Studies of flows through N-sequential orifices

Critical mass flux and axial pressure profile data for fluid nitrogen are presented for N = 20, 15, 10, and 7 N-sequential-orifice-inlet configurations uniformly spaced at 15.5 cm. These data correlate well over a wide range in reduced temperature and reduced pressure, and are in general agreement with previous studies of one to four inlets. Experimental and theoretical agreement is good for liquid and gas critical mass flux, but inconclusive in the near thermodynamic critical regions.

Hendricks, R. C.↗
NASA NTRS1984

The effect of plasma on solar cell array arc characteristics

The influence from the ambient plasma on the arc characteristics of a negatively biased solar cell array was investigated. The arc characteristics examined were the peak current during an arc, the decay time as the arc terminates, and the charge lost during the arc. These arc characteristics were examined in a nitrogen plasma with charge densities ranging from 15,000 to 45,000 cu cm. Background gas pressures ranged from 8x1,000,000 to 6x100,000 torr. Over these ranges of parameters no significant effect on the arc characteristics were seen. Arc characteristics were also examined for three gas species: helium, nitrogen and argon. The helium arcs have higher peak currents and shorter decay times than nitrogen and argon arcs. There are slight differences in the arc characteristics between nitrogen and argon. These differences may be caused by the differences in mass of the respective species. Also, evidence is presented for an electron emission mechanism appearing as a precursor to solar array arcs. Occassionally the plasma generator could be turned off, and currents could still be detected in the vacuum system. When these currents are presented, arcs may occur.

Snyder, D. B.↗
NASA NTRS1985

The effect of plasma on solar cell array arc characteristics

The influence from the ambient plasma on the arc characteristics of a negatively biased solar cell array was investigated. The arc characteristics examined were the peak current during an arc, the decay time as the arc terminates, and the charge lost during the arc. These arc characteristics were examined in a nitrogen plasma with charge densities ranging from 15,000 to 45,000 cu cm. Background gas pressures ranged from 8x1,000,000 to 6x100,000 torr. Over these ranges of parameters no significant effect on the arc characteristics were seen. Arc characteristics were also examined for three gas species: helium, nitrogen and argon. The helium arcs have higher peak currents and shorter decay times than nitrogen and argon arcs. There are slight differences in the arc characteristics between nitrogen and argon. These differences may be caused by the differences in mass of the respective species. Also, evidence is presented for an electron emission mechanism appearing as a precursor to solar array arcs. Occasionally the plasma generator could be turned off, and currents could still be detected in the vacuum system. When these currents are presented, arcs may occur.

Snyder, D. B.↗
NASA NTRS1985

A spectacular nitrogen isotope anomaly in Bencubbin

Results of isotopic measurements on an unusual stony-iron meteorite named Bencubbin, which was found in Western Australia in 1930, are reported. Nitrogen from both the metallic and stony parts of the Bencubbin meteorite was analyzed, and in both materials large excesses of (15)N were found, resulting in values of the (14)N/(15)N abundance ratios as low as 137. That is, (15)N is enriched in Bencubbin by about a factor of two relative to terrestrial nitrogen. This is the largest (15)N enrichment of any known natural material. The effect is so large that chemical processes are probably inadequate to account for it. Nuclear processes which may be responsible for the anomalous isotope abundance are discussed.

Prombo, C. A.↗
NASA NTRS1986

Detection of surface glow related to spacecraft glow phenomena

A source of low energy neutral atoms and molecules has been developed by using a biased limiter to scrape off and reflect neutralized ions from a toroidal plasma. Beams of nitrogen and nitrogen-oxygen mixtures with energies of 1 to 15 eV and fluxes greater than about 10 to the 14 per centimeter per second were directed onto target surfaces consisting of Z-302 and Z-306 paints. With the nitrogen beams, a glow due to beam-surface interactions was successfully detected. In addition, a volume glow effect due to beam-gas interactions was observed which may play a role in spacecraft glow.

Langer, W. D.↗
NASA NTRS2017

Revised Models of Interstellar Nitrogen Isotopic Fractionation

Nitrogen-bearing molecules in cold molecular clouds exhibit a range of isotopic fractionation ratios and these molecules may be the precursors of (15)N enrichments found in comets and meteorites. Chemical model calculations indicate that atom-molecular ion and ion-molecule reactions could account for most of the fractionation patterns observed. However, recent quantum-chemical computations demonstrate that several of the key processes are unlikely to occur in dense clouds. Related model calculations of dense loud chemistry show that the revised (15)N enrichments fail to match observed values. We have investigated the effects of these reaction rate modifications on the chemical model of Wirstrom et al. (2012) for which there are significant physical and chemical differences with respect to other models. We have included (15)N fractionation of CN in neutral-neutral reactions and also updated rate coefficients for key reactions in the nitrogen chemistry. We find that the revised fractionation rates have the effect of suppressing (15)N enrichment in ammonia at all times, while the depletion is even more pronounced, reaching (14)N/(15)N ratios of > 2000. Taking the updated nitrogen chemistry into account, no sigificant enrichment occurs in HCN or HNC, contrary to observational evidence in dark clouds and comets, although the (14)N/(15)N ratio can still be below 100 in CN itself. However, such low CN abundances are predicted that the updated model falls short of explaining the bulk (15)N enhancements observed in primitive materials. It is clear that alternative fractionating reactions are necessary to reproduce observations, so further laboratory and theoretical studies are urgently needed.

Astrochemistry↗
NASA NTRS1962

BOILING HEAT TRANSFER TO LIQUID HYDROGEN AND NITROGEN IN FORCED FLOW

Boiling heat transfer to liquid hydrogen and nitrogen was investigated experimentally. Results are presented from a study of bulk boiling inside a cylindrical tube under vertically upward forced-flow conditions. A 0.555-inch-inside-diameter and 16 (1/8)-inch-long electrically heated stainless-steel tube was used. The range of variables studied for hydrogen were mass velocity of 2850 to 17,000 pounds per hour per square foot, local heat flux of 3600 to 40,000 Btu per hour per square foot, inlet pressure of 30 to 74 pounds per square inch absolute, and inlet subcooling of 0° to 9° R. Nitrogen test conditions were mass velocity of 15,000 to 56,000 pounds per hour per square foot, local heat flux of 2300 to 40,000 Btu per hour per square foot, inlet pressure of 47 to 56 pounds per square inch absolute, and inlet sub cooling of 1° to 6° R. The axial distribution of the tube-wall temperatures is presented. A transition in the type of boiling heat transfer was obtained. The critical heat flux corresponding to this transition was determined over a range of flow and heating rates and local qualities. At specific combinations of flow and transition location, a range of critical-heat-flux values was obtained and maximum values were determined. The maximum critical heat flux increased with increasing fluid-flow rate and decreased with increasing length of tube before transition. Similar variations of the maximum critical heat flux have been reported for water. The tube-inner-wall temperatures upstream of transition were essentially uniform and were only slightly greater than the fluid saturation temperature. The Wall-temperature profiles downstream of transition generally resembled those obtained in film-boiling studies and appeared to be strongly dependent upon local quality at the point of transition. Maximum wall temperatures of 9000 and 18000 R were obtained with hydrogen and nitrogen, respectively. Fluctuations of pressure, flow rate, and temperature occurred during some of the boiling tests. Under some conditions, maximum critical-heat-flux values were attained during steady-state operation with fluctuations. In other cases the fluctuations became uncontrolled, and critical-flux values less than the maximum values were obtained upon restabilization of the test conditions. No measurable pressure drop across the test section was obtained at any condition.

LIQUID HYDROGEN↗
NASA NTRS2003

Nitrogen Isotopic Ratio in Jupiter's Atmosphere from Observations by Composite Infrared Spectrometer (CIRS) on the Cassini Spacecraft

The Composite Infrared Spectrometer (CIRS) on the Cassini spacecraft made infrared observations of Jupiter's atmosphere during the flyby in December 2000 to January 2001. The unique database in the 600-1400/cm region with 0.53 and 2.8/cm spectral resolutions obtained from the observations permits retrieval of global maps of the thermal structure and composition of Jupiter's atmosphere including the distributions of (14)NH3 and (15)NH3. Analysis of Jupiter's ammonia distributions from three isolated (15)NH3 spectral lines in eight latitudes is presented for evaluation of the nitrogen isotopic ratio. The nitrogen isotopic ratio (14)N/(15)N (or (15)N/(14)N) in Jupiter's atmosphere in this analysis is calculated to be: 448 +/- 62 ((2.23 +/- 0.31) x 10(exp -3)). This value of the ratio determined from CIRS data is found to be in very close agreement with the value previously obtained from the measurements by the Galileo Probe Mass Spectrometer. Some possible mechanisms to account for the variation of Jupiter's observed isotopic ratio relative to various astrophysical environments are discussed.

Abbas, M. M.↗
NASA NTRS1980

Nitrogen dioxide vapor penetration of chlorobutyl rubber SCAPE under operational conditions

Operational self contained atmospheric protective ensembles (SCAPE suits) and fabric from the suits were subjected to a series of tests designed to determine the amount of exposure a wearer of the suit would receive if a spill of the hypergolic oxidizer nitrogen tetroxide (N2O4) should occur nearby. The results of these tests show that a wearer of a "stock" SCAPE suit equipped with a standard liquid air pack, if exposed to a spill resulting in a 26 percent increase of oxidizer in the surrounding atmosphere, will experiment no detectable concentration of nitrogen dioxide (NO2) inside the suit for 15 minutes. Thereafter, the NO2 concentration within the suit will increase for 35 minutes at a rate of 0.07 ppm per minute and then at a gradually decreasing rate until an equilibrium concentration of 3.4 ppm is attained after 100 minutes. Momentary increases of as much as 1.6 ppm can be expected if the wearer were to rise quickly from a squatting position, but the additional NO2 would be dissipated within three minutes. The effect of liquid and vapor N2O4 and of liquid monomethylhydrazine on permeation rates and tensile strength of the SCAPE suit fabric was also investigated.

Schehl, T. A.↗
NASA NTRS1981

Plasma observations near Saturn - Initial results from Voyager 1

The Voyager 1 encounter with Saturn and its satellites yielded extensive measurements of magnetospheric low-energy plasma electrons and positive ions, both heavy and light, probably of hydrogen and nitrogen or oxygen. At radial distances between 15 and 7 Saturn radii on the inbound trajectory, the plasma appears to corotate with a velocity within 20% of that theoretically expected for rigid corotation. The Titan data, taken while the moon was inside the Saturn magnetosphere, shows a clear signature characteristic of the interaction between a subsonic corotating magnetospheric plasma and the atmospheric or ionospheric exosphere of Titan.

Bridge, H. S.↗
NASA NTRS1983

The response of thermospheric atomic nitrogen to magnetic storms

Neutral composition data obtained by the open-source neutral-mass spectrometer on the polar orbiting Atmosphere Explorer D satellite during the periods October 31 to November 15, 1975, and January 5 to 15, 1976, are used to characterize the response of thermospheric atomic nitrogen densities to geomagnetic activity. These periods provided nearly simultaneous polar and low-latitude data coverage. At low and middle latitudes near dawn and at all latitudes on the dayside, N densities at 400 km appear to vary like those of a species of atomic mass 14: N is observed to increase with increasing geomagnetic activity in a manner similar to that of O. At auroral latitudes near dawn, however, there is a more complex dependence on the amplitude of the disturbance. For substorm-scale activity, N tends to increase during periods of auroral heating but exhibits a sharp temporary decrease afterward. During large storms there is a significant but short-lived increase of N at auroral latitudes. The present results support current models showing that N is produced and transported out of the auroral zone during geomagnetic disturbances.

Engebretson, M. J.↗
NASA NTRS1989

A brief review of JPL's electric propulsion technology activities

Near-term objectives and recent technological progress of JPL's electric propulsion program are discussed. Particular attention is given to accomplishments for ion, magnetoplasmadynamic (MPD), electron-cyclotron resonance (ECR), and arcjet thrusters. Xenon ion thruster erosion tests indicate a 15-fold reduction in tantalum baffle erosion when nitrogen is added to the xenon propellant and steady-state cylindrical MPD thruster tests at powers up to 72 kW show distinct self-constricted and diffuse discharge modes. An ECR thruster was operated at up to 7 kW with plasma acceleration at energies up to 7 kW; there was plasma acceleration at energies approaching 100 electron volts.

Barnett, John W.↗
NASA NTRS1991

Theoretical studies of volatile processes in the outer solar system

Four studies of volatile processes in the outer solar system are discussed. Researchers suggest that the convective and conductive regions of Triton's atmosphere join at the tropopause near 10 km. A model of volatile transport on Triton's surface was constructed that predicts that Triton's surface north of 15 degrees north latitude is experiencing deposition of nitrogen frosts, as are the bright portions of the south polar cap near the equator. Also discussed are numerical models of the evolution of Titan's surface and atmosphere. Results of a study of the rheology of ammonia-water liquids were applied to the icy satellites of the outer solar system. Finally, the researchers examined the frictional heating, sublimation, and re-condensation of grains free-falling into the solar nebula from a surrounding interstellar cloud. The sublimation model includes the effect of various volatile species and accounts for the poor radiating properties of small grains using Mie theory.

Lunine, Jonathan I.↗
NASA NTRS1992

High-flux source of low-energy neutral beams using reflection of ions from metals

Reflection of low-energy ions from surfaces can be applied as a method of producing high-flux beams of low-energy neutral particles, and is an important effect in several areas of plasma technology, such as in the edge region of fusion devices. We have developed a beam source based on acceleration and reflection of ions from a magnetically confined coaxial RF plasma source. The beam provides a large enough flux to allow the energy distribution of the reflected neutrals to be measured despite the inefficiency of detection, by means of an electrostatic cylindrical mirror analyzer coupled with a quadrupole mass spectrometer. Energy distributions have been measured for oxygen, nitrogen, and inert gas ions incident with from 15 to 70 eV reflected from amorphous metal surfaces of several compositions. For ions of lighter atomic mass than the reflecting metal, reflected beams have peaked energy distributions; beams with the peak at 4-32 eV have been measured. The energy and mass dependences of the energy distributions as well as measurements of absolute flux, and angular distribution and divergence are reported. Applications of the neutral beams produced are described.

Cuthbertson, John W.↗
NASA NTRS1993

Design, analysis, and fabrication of oxide-coated iridium/rhenium combustion chambers

Iridium-coated rhenium (Ir/Re) combustion chambers provide high temperature, oxidation-resistant operation for radiation-cooled liquid-fueled rocket engines. A 22-N (5-lb(sub f)) chamber has been operated for 15 hours at 2200 C (4000 F) using nitrogen tetroxide/monomethyl hydrazine (NTO/MMH) propellant, with negligible internal erosion. The oxidation resistance of these chambers could be further increased by the addition of refractory oxide coatings, providing longer life and/or operation in more oxidizing and higher temperature environments. The oxide coatings would serve as a thermal and diffusion barrier for the iridium coating, lowering the temperature of the iridium layer while also preventing the ingress of oxygen and egress of iridium oxides. This would serve to slow the failure mechanisms of Ir/Re chambers, namely the diffusion of rhenium to the inner surface and the oxidation of iridium. Such protection could extend chamber lifetimes by tens or perhaps hundreds of hours, and allow chamber operation on stoichiometric or higher mixture ratio oxygen/hydrogen (O2/H2) propellant. Extensive thermomechanical, thermochemical, and mass transport modeling was performed as a key material/structure design tool. Based on the results of these analyses, several 22-N oxide-coated Ir/Re chambers were fabricated and delivered to NASA Lewis Research Center for hot-fire testing.

Jang, Q.↗