Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Monolithic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Hermeticity of SiC/SiC composite and monolithic SiC tubes irradiated under radial high-heat flux

Demonstration of hermetic SiC fiber–reinforced SiC matrix composite cladding under normal operating environments has been identified as one of the most critical feasibility issues for accident-tolerant fuel cladding in light-water reactors. This study provides critical experimental data needed for understanding the effects of irradiation on hermeticity. SiC composite and monolithic tubes were neutron-irradiated to 2 displacements per atom with and without a nominal radial heat flux of 0.6 MW/m2 to produce a simulated in-pile stress state for the normal operation of a light-water reactor. The through-thickness temperature gradient under irradiation results in a gradient in swelling, which causes a significant stress buildup. Such irradiation-induced stress was modeled using a commercial finite element analysis code. The radial heat flux–irradiation synergism was experimentally investigated by constructing a special irradiation capsule and evaluating the helium hermeticity of the specimens. The simulated stress state exhibited a near equi-biaxial tensile axial and hoop stress of ~150 MPa at the inner surface of the SiC composite tube. This stress level is potentially beyond the matrix cracking stress. Degradation of hermeticity of the SiC composite tubes was observed after irradiation, indicating irradiation-induced cracking, whereas the irradiated monolithic SiC tubes remained hermetic. In conclusion, the results indicate that loss of hermeticity caused by radiation-induced microcracking is a potential issue for SiC composite cladding, depending on the magnitude of the temperature gradients. Coating the outer surface of the cladding was identified as a mitigation strategy that might overcome the cracking issue.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Preliminary conceptual design of fast neutron spectrum nuclear thermal rocket cores using monolithic uranium nitride fuel

This paper presents a few nuclear thermal rocket (NTR) reactor core preliminary conceptual designs based on the use of monolithic uranium nitride (UN) fuel plates or pins clad with tungsten (W), alloyed or unalloyed as needed. High-assay low-enriched uranium (HALEU) as well as high-enriched uranium (HEU) are considered. Nominal core thermal powers are between 300 and 1100 MW corresponding to thrusts between 66 kN and 240 kN. The estimated thrust-to-reactor-weight ratios (T/WRx) achievable with the HEU plate and pin configurations are between 3.8 and 10.9. The T/WRx achievable with the HALEU plate and pin configurations are lower, 1.9–4.0, than those achievable with HEU. It is noteworthy that even a relatively modest increase in fuel enrichment above the HALEU limit enables a significant increase in T/WRx. It must be emphasized that these results do not yet account for uncertainties and that the appropriateness of the assumed fuel thermal design limits for normal operation (i.e., peak centerline temperature of 3100 K) will need to be confirmed. Finally, just like for the other UN-based fuels currently considered for NTR applications (i.e., CERMET and CERCER), the proposed UN fuel systems need significant testing in prototypic conditions to confirm the appropriate performance for safe NTR applications. However, the monolithic fuel systems may have, overall, a higher technology readiness level (TRL), and, consequently, shorter fuel development and validation time may result.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Efficient monolithic all-perovskite tandem solar modules with small cell-to-module derate

All-perovskite tandem solar modules are promising to reduce the cost of photovoltaic systems with their high efficiency and solution fabrication, but their sensitivity to air still imposes a great challenge. Here a hot gas-assisted blading method is developed to accelerate the perovskite solidification, forming compact and thick narrow bandgap (NBG) perovskite films. Adding a reduction agent into NBG films followed by a short period of air exposure and a post-fabrication storage surprisingly increases carrier recombination lifetime and enables laser scribing in ambient conditions without obvious loss of device performance. This combination suppresses tin and iodide oxidation and forms a thin SnO 2 layer on the NBG film surface. Monolithic all-perovskite tandem solar modules showed a champion efficiency of 21.6% with a 14.3 cm 2 aperture area, corresponding to an active area efficiency of 23.0%. Lastly, the very small cell-to-module derate of 6.5% demonstrates the advantage of a tandem monolithic structure for solar modules.

14 SOLAR ENERGY↗
DOE OSTI2025

Dependent scattering and fractal microstructure determine the transparency of aerogel monoliths

This study reveals how dependent scattering and microstructure significantly affect electromagnetic wave propagation through aerogel monoliths, contributing to their transparency. Light scattering by particle ensembles is considered “dependent” when the scattering properties rely not only on particle size and optical constants but also on their spatial distribution, typically occurring when the average interparticle distance is small in comparison with the wavelength of incident radiation. Addressing dependent scattering requires solving Maxwell’s equations for complex heterogeneous structures, which is computationally demanding and usually limited to sample thicknesses on the same scale as the wavelength. This study combines computer-generated ambigel microstructures of fractal aggregates of polydisperse nanoparticles and the radiative transfer with reciprocal transaction method to predict the transmittance of thick ambigel slabs. Transmittance measurements of ambiently dried aerogel monoliths (ambigels) with porosities from about 50% to 90% closely matched the predicted values for their digital twins. However, ignoring dependent scattering or particle aggregation led to inaccurate predictions. This study validated the computational framework, and its findings offer insights for designing photonic metamaterials and analyzing their interactions with electromagnetic waves.

Yalcin, Refet A. (ORCID:0000000339973494)↗
DOE OSTI2025

Monolithic optoelectronic circuit design for on-chip terahertz applications

We demonstrate a monolithic coplanar stripline platform for on-chip terahertz (THz) generation, transmission, and detection, addressing key challenges of mode purity, bandwidth, and referencing. Capacitive coupling of the photoconductive generator switch enforces pure odd-mode propagation, increases THz field strength, and extends the operational frequency range, achieving 0.05–1.4 THz. Our architecture enables fully monolithic fabrication with amorphous silicon switches, in situ field referencing, and galvanic isolation between generation and detection. Finite-element simulations and experiments confirm that suppressing parasitic modes improves signal integrity, providing a robust platform for high-fidelity THz spectroscopy, ultrafast electronics, and nanoscale quantum materials research.

Capacitive coupling↗
DOE OSTI2026

Advanced monolithic 2D multilayer Laue lens (MLL) optics for hard x-ray nanofocusing and nanotomography

We report on the development of a new generation of monolithic two-dimensional (2D) multilayer Laue lens (MLL) optics suitable for high-resolution hard x-ray nanoimaging. The 2D optics were assembled on microfabricated silicon templates with high orthogonality and lateral alignment precision, which were characterized using white-light interferometry and confirmed by x-ray measurements. The developed monolithic 2D MLL optics were successfully employed for hard x-ray nanofocusing and nanotomography experiments using the ptychography imaging modality, demonstrating sub-10 nm resolution in 2D and sample-limited ∼30 nm in three-dimensional while exhibiting excellent stability during extended measurements. The new 2D MLL templates with high alignment accuracy represent an important step forward in the development of 2D MLL optics toward direct nanoimaging experiments with sub-10 nm spatial resolution.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Characterization of a SiPM-based monolithic neutron scatter camera using dark counts

The Single Volume Scatter Camera (SVSC) Collaboration aims to develop portable neutron imaging systems for a variety of applications in nuclear non-proliferation. Conventional double-scatter neutron imagers are composed of several separate detector volumes organized in at least two planes. A neutron must scatter in two of these detector volumes for its initial trajectory to be reconstructed. As such, these systems typically have a large footprint and poor geometric efficiency. We report on the design and characterization of a prototype monolithic neutron scatter camera that is intended to significantly improve upon the geometrical shortcomings of conventional neutron cameras. The detector consists of a 50 mm×56 mm× 60 mm monolithic block of EJ-204 plastic scintillator instrumented on two faces with arrays of 64 Hamamatsu S13360-6075PE silicon photomultipliers (SiPMs). The electronic crosstalk is limited to < 5% between adjacent channels and < 0.1% between all other channel pairs. SiPMs introduce a significantly elevated dark count rate over PMTs, as well as correlated noise from after-pulsing and optical crosstalk. In this article, we characterize the dark count rate and optical crosstalk and present a modified event reconstruction likelihood function that accounts for them. We find that the average dark count rate per SiPM is 4.3 MHz with a standard deviation of 1.5 MHz among devices. The analysis method we employ to measure internal optical crosstalk also naturally yields the mean and width of the single-electron pulse height. Here, we calculate separate contributions to the width of the single-electron pulse-height from electronic noise and avalanche fluctuations. We demonstrate a timing resolution for a single-photon pulse to be (128 ± 4) ps. Finally, coincidence analysis is employed to measure external (pixel-to-pixel) optical crosstalk. We present a map of the average external crosstalk probability between 2×4 groups of SiPMs, as well as the in-situ timing characteristics extracted from the coincidence analysis. Further work is needed to characterize the performance of the camera at reconstructing single- and double-site interactions, as well as image reconstruction.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Reverse-Bias Resilience of Monolithic Perovskite/Silicon Tandem Solar Cells

Metal halide perovskites have rapidly enabled a range of high-performance photovoltaic technologies. However, catastrophic failure under reverse voltage bias hinders their commercialization. In this work, we demonstrate that by employing a monolithic perovskite/silicon tandem structure, the perovskite subcell can be effectively protected by the silicon subcell under reverse bias, owing to the low reverse-bias diode current of the silicon subcell. As a result, the tested perovskite/silicon tandem devices show superior reverse-bias resilience compared to perovskite single-junction devices in both long-term reverse voltage biasing tests at the single-cell level and partial shading tests at the module level. These results highlight that, compared to other perovskite technologies, monolithic perovskite/silicon tandems are at a higher technology readiness level in terms of tackling the reverse-bias and partial shading challenge, which is a considerable advantage towards commercialization.

commercialization↗
DOE OSTI2020

Monolithic ATF MiniFuel Sample Capsules Ready for HFIR Insertion

Several advanced nuclear fuel concepts are being considered throughout the nuclear industry. Implementation of these concepts could increase accident tolerance or enhance performance beyond the capabilities of the UO₂-based nuclear fuel currently in use. Qualification and deployment of any new fuel requires rigorous irradiation testing to demonstrate performance under representative normal and off-normal operating conditions. The traditional approach for qualifying new fuels requires exhaustive execution of many integral fuel tests. However, due to the long timeframe for executing these integral tests and the limited number of available materials test reactors, this approach is becoming impractical. To accelerate fuel qualification, Oak Ridge National Laboratory developed the MiniFuel irradiation vehicle for use in conducting accelerated separate effects irradiation testing of a wide range of nuclear fuel materials in the High Flux Isotope Reactor (HFIR). The first MiniFuel irradiations performed in the facility tested sol gel–derived uranium nitride kernels and tristructural isotropic (TRISO)-coated particle fuels. This report describes the preparation and assembly of the first set of monolithic MiniFuel irradiations conducted to support accident-tolerant fuel (ATF) development and accelerated fuel qualification. Two irradiation targets containing a variety of UO₂ and U₃Si₂ disk fuel specimens were fabricated and assembled for irradiation to burnups of 8-10 and 28-40 MWd/kg U. The target irradiation temperature is 450-550°C. Irradiation of U₃Si₂ will provide new data regarding the irradiation performance of a candidate ATF to complement current ATF-1 integral experiments being performed in the Advanced Test Reactor. UO₂ samples were included as a reference so that the results from the MiniFuel experiments can be compared with the extensive UO₂ fuel performance database. The monolithic MiniFuel capsules were successfully assembled, welded, and tested per HFIR requirements and are ready for insertion into the reactor. Pictures of the assembly process are included in this report. The experiment is planned for insertion into the HFIR during cycle 487 in April 2020.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

The Monolithic Heat Pipe Microreactor Reference Plant Model Updates

This work presents the latest improvements to, and investigations performed with, the generic monolithic heat-pipe-cooled microreactor reference plant model for the United States Nuclear Regulatory Commission. This model serves as the foundation for the future detailed design evaluation models based on license applications. This model has been developed with the Comprehensive Reactor Analysis Bundle (BlueCRAB) and its specifications are based on open literature publications for the eVinci™ design . BlueCRAB is the U.S. Nuclear Regulatory Commission non-light-water reactor analysis system based on MOOSE, the Multiphysics Object-Oriented Simulation Environment framework, which can couple the Griffin, BISON, and Sockeye applications to resolve the various physics that are essential for the safety analysis of this type of reactor system. The core specifications include tristructural isotropic fuel, graphite monolith, graphite reflectors, and drums composed of graphite and B 4 C.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Product selectivity and mass transport in levulinic acid transfer hydrogenation by monolithic MIL-100, MIL-88B and ZIF-8@Pd MOFs

The diffusion processes between adsorbent and adsorbate naturally play a significant role in the efficiency and selectivity of the heterogenous catalytic process. This paper considers the importance of diffusion processes in the transfer hydrogenation reaction of levulinic acid to γ-valerolactone by MIL-88B, MIL-100, and ZIF8@Pd monolithic catalysts. Over a period of five catalytic cycles, it was shown that the Fe-based catalysts can achieve similar conversions to the ZIF-8 supported Pd, with the only current limitation being the lower aqueous stability of these MOFs. Diffusion constants were calculated using the ZLC method, with micropore diffusion limitation found for ZIF-8 and MIL-100 monolithic frameworks at 2.7 x 10 -8 and 4.6 x 10 -8 cm 2 s -1 respectively. This diffusion limitation was also confirmed by IR spectroscopy with an increasing concentration of C—H bands on the MOF substrate post-reaction. Mass transfer coefficients, also calculated by ZLC, revealed increased mass transport for the hydrophobic ZIF-8 framework, which perhaps aids in the γ-valerolactone selectivity over side products that are produced in the absence of catalytic material, as seen for MIL-88B and MIL-100 after multiple uses.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Monolithic Polyepoxide Membranes for Nanofiltration Applications and Sustainable Membrane Manufacture

The present work details the development of carbon fiber-reinforced epoxy membranes with excellent rejection of small-molecule dyes. It is a proof-of-concept for a more sustainable membrane design incorporating carbon fibers, and their recycling and reuse. 4,4′-methylenebis(cyclohexylamine) (MBCHA) polymerized with either bisphenol-A-diglycidyl ether (BADGE) or tetraphenolethane tetraglycidylether (EPON Resin 1031) in polyethylene glycol (PEG) were used to make monolithic membranes reinforced by nonwoven carbon fibers. Membrane pore sizes were tuned by adjusting the molecular weight of the PEG used in the initial polymerization. Membranes made of BADGE-MBCHA showed rejection of Rose Bengal approaching 100%, while tuning the pore sizes substantially increased the rejection of Methylene Blue from ~65% to nearly 100%. The membrane with the best permselectivity was made of EPON-MBCHA polymerized in PEG 300. It has an average DI flux of 4.48 LMH/bar and an average rejection of 99.6% and 99.8% for Rose Bengal and Methylene Blue dyes, respectively. Degradation in 1.1 M sodium hypochlorite enabled the retrieval of the carbon fiber from the epoxy matrix, suggesting that the monolithic membranes could be recycled to retrieve high-value products rather than downcycled for incineration or used as a lower selectivity membrane. The mechanism for epoxy degradation is hypothesized to be part chemical and part physical due to intense swelling stress leading to erosion that leaves behind undamaged carbon fibers. The retrieved fibers were successfully used to make another membrane exhibiting similar performance to those made with pristine fibers.

Polymer Science↗
DOE OSTI2021

Thermo-physical Properties of U-10Mo Monolithic Fuel

Monolithic fuel is a candidate fuel form that is being considered for the conversion of high-performance research reactors. This plate-type fuel consists of a high-density, U-Mo fuel in a monolithic form that is sandwiched between zirconium diffusion barriers and encapsulated in an aluminum cladding. To date, many plates were irradiated with a satisfactory irradiation performance, demonstrating that the conceptual design works. The program is now moving to the qualification phase, a predecessor to the timely conversion of the target reactors. To qualify this fuel system, the program must show that the fuel plates have predictable behavior, meet the safety standards, and perform well in reactors. The requirement of a satisfactory irradiation performance under normal operating conditions is primarily demonstrated by a successful testing. To demonstrate that the fuel system has a predictable behavior, the several key material properties should be quantified accurately since these properties are needed to estimate the thermal and mechanical behavior of the fuel system. Although, there is a large set of thermophysical property data available for unirradiated material, the property data for irradiated fuel is scarce. Since irradiation causes drastic effects in material, a significant change in material properties occurs. Consequently, using representative degradation models becomes essential for accurate performance assessments. This work examines thermal conductivity of U-10Mo, by evaluating recent experimental data from the literature and available theoretical models. The study has discovered inconsistencies in the literature data, revealing that previously developed theoretical models fail to predict the thermal conductivity of irradiated fuel.

42 ENGINEERING↗
DOE OSTI2022

Airfoil with CMC liner and multi-piece monolithic ceramic shell

An airfoil includes an airfoil section that has an airfoil wall that surrounds a cavity. The airfoil wall includes an exterior monolithic ceramic shell and an interior CMC liner that has CMC plies. An outermost ply of the CMC plies forms tabs that are raised from an underlying ply so as to define a slot. The exterior monolithic ceramic shell includes an underlapping shell piece and an overlapping shell piece. The underlapping shell piece has a portion disposed in the slot and bonded with the tabs. The overlapping shell piece extends over the tabs and is bonded to the tabs. There are channels bounded by adjacent ones of the tabs, the underlapping shell piece, and the overlapping shell piece. Channel orifices through the CMC liner connect the cavity and the channels.

Martin, Thomas J.↗
DOE OSTI2024

Mapping the Microstructure During the Historic U-Mo Monolithic Fuel Foil Fabrication Process

Since 2004, there has been extensive effort towards the development of a uranium molybdenum monolithic fuel system to convert high performance research and test reactors. The RERTR-6 experiment was the first to attempt a monolithic fuel instead of a dispersed fuel form. The fabrication methods evolved overtime and provided the basis for current fabrication methods. The various steps in the process inevitably tailor the fuel alloy microstructure which is known to influence irradiation behavior. This document aims to present and discuss the fabrication evolution that transpired through a recounting of historical data from the various fabrication campaigns. By overlaying this data with basic science studies on the U-Mo that explored transformation kinetics, it is possible to estimate a measure of the impact heat treatments have on the final as-fabricated microstructure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Monolithic Photoelectrochemical CO 2 Reduction Producing Syngas at 10% Efficiency

We report increasing anthropogenic carbon dioxide emissions have prompted the search for photoelectrochemical (PEC) methods of converting CO 2 to useful commodity products, including fuels. Ideally, such PEC approaches will be sustained using only sunlight, water, and CO 2 as energetic and reactant inputs. However, low peak conversion efficiencies (< 5%) have made commercialization of fully-integrated PEC devices prohibitive. Here, a 4 cm 2 monolithic PEC device exceeding 10% solar-to-fuel efficiency with principal fuel products of carbon monoxide and hydrogen is reported. The corresponding solar-to-CO and solar-to-H 2 efficiencies are 7% and 3.5%, respectively. Screening of a range of operating conditions reveals a tunable product mixture of H 2 and CO using a gold electrocatalyst. Accordingly, it is shown that device optimization yields a H 2 -to-CO ratio of 1:2 commonly present in synthesis gas (syngas). Notably, the modularity and facile fabrication of this device permit the incorporation of a broad array of materials for various applications. For example, the electrocatalyst may easily be swapped to target a different set of products.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Cooperative and bifunctional Ga-Ca-Cr 2 O 3 @CaO structured monoliths as versatile platform for reactive capture of CO 2 and its subsequent conversion to ethylene

Cooperative and bifunctional materials (BFMs) that integrate adsorbents and catalysts offer a promising strategy for the reactive capture of CO 2 to produce valuable fuels and chemicals. In this study, we developed structured BFMs via 3D printing that combine CaO as an adsorbent with Ga–Ca–Cr 2 O 3 metal oxides as the catalyst for the reactive capture of CO 2 and its subsequent conversion to C 2 H 4 via the oxidative dehydrogenation of C 2 H 6 (CO 2 -ODHE). Three different Ga–Ca compositions were used to modify the catalyst surface characteristics and enhance C 2 H 4 selectivity. In these formulations, Ga ions stabilize the oxygen lattice of the BFM, while Ca ions interact strongly with Cr to form CaCrO 4 , thereby altering the oxygen species and enhancing the material’s basic properties. Under adsorption–reaction conditions at 600–650 °C, the optimal BFM achieved an excellent C 2 H 4 selectivity of 96.4 %, attributed to a balanced redox process and improved basicity that facilitate efficient C 2 H 6 conversion and rapid desorption of C 2 H 4 without excessive oxidation. Overall, this work provides new insights into the formulation of BFMs monoliths and highlights the critical role of catalytic surface modification in enhancing C 2 H 4 selectivity in the CO 2 -ODHE reactive capture process.

C2H4 production↗