Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Model Optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Theoretic aspects of the identification of the parameters in the optimal control model

The identification of the parameters of the optimal control model from input-output data of the human operator is considered. Accepting the basic structure of the model as a cascade of a full-order observer and a feedback law, and suppressing the inherent optimality of the human controller, the parameters to be identified are the feedback matrix, the observer gain matrix, and the intensity matrices of the observation noise and the motor noise. The identification of the parameters is a statistical problem, because the system and output are corrupted by noise, and therefore the solution must be based on the statistics (probability density function) of the input and output data of the human operator. However, based on the statistics of the input-output data of the human operator, no distinction can be made between the observation and the motor noise, which shows that the model suffers from overparameterization.

Vanwijk, R. A.↗
NASA NTRS1977

Display analysis with the optimal control model of the human operator

Application of the optimal control model of the human operator to problems in display analysis is discussed. Those aspects of the model pertaining to the operator-display interface and to operator information processing are reviewed and discussed. The techniques are then applied to the analysis of advanced display/control systems for a Terminal Configured Vehicle. Model results are compared with those obtained in a large, fixed-base simulation.

Baron, S.↗
NASA NTRS1990

Influence of structural and aerodynamic modeling on optimization with flutter constraint

The influences of structural and aerodynamic modeling on multidisciplinary optimization in an aeroelastic environment are not well understood. Therefore, optimizations with flutter and frequency constraints were performed to investigate the effects these modeling factors have on various representative wings. To this end, the Automated Structural Optimization System (ASTROS) was used as a tool to minimize the weight of various fully built-up finite element wing models in subsonic and supersonic flow under given flutter and frequency constraints. First, the performance of the optimization module was tested against results from other codes on a straight and uniform wing widely used for optimization with flutter constraints. Then, fully built-up finite element models of various wings with different aspect ratios were investigated for the influence on the structural optimization for minimum weight of the following modeling factors: finite element selection, structural grid refinement; number of selected modes, retention of breathing modes; selection of reduced frequencies to be used in flutter analysis; aerodynamic panel size and placement; splining of the aerodynamic grid to the structural grid selection of extra points of the structural wing box for splining; and number of constraints to be retained. Knowledge of these influences as well as of the program behavior is important, since optimization can be made more efficient by the selection of reasonable initial models. Also, it was shown previously that modeling has an impact on the results of modal and aeroelastic analyses. Thus, if modeling errors can negatively affect the analyses, a minimum weight optimization can be jeopardized and result in an optimal design that is rather unreliable. In the following, selected results are presented and the influences of some modeling parameters on optimization are pointed out.

Striz, Alfred G.↗
NASA NTRS1984

Problems in large-scale structural optimization

A general design optimization model for large complex systems is defined. Major features of the model that challenge various optimization algorithms are discussed. Requirements of a model optimization algorithm are identified. Objectives of the study of various algorithms are defined and a basis for conducting such a study is developed. Primal as well as transformation methods are analytically studied and a unified viewpoint of various methods is presented. Several numerical examples are solved using different methods to study their performance. Conclusions drawn from the study are presented and discussed. Areas of future research in nonlinear programming as well as structural optimization are identified and discussed.

Arora, J. S.↗
NASA NTRS1981

Aircraft control-display analysis and design using the optimal control model of the human pilot

The use of the optimal control model (OCM) of the human pilot as a design tool is discussed. A novel procedure for the assignment and selection of model parameters in the absence of experimental data is proposed. A technique for partitioning a weakly coupled, multiaxis task into approximate state-uncoupled, single-axis tasks is introduced. The resulting modeling technique is utilized in the design and analysis of an aircraft flight-director system. This flight-director design technique differs from previous related work using the OCM in that considerable effort is devoted to ensuring that the OCM-designed director exhibits the desirable frequency-domain characteristics associated with experimentally verified classical designs (e.g., K/s 'effective vehicle' characteristics, noninteracting controls). The implications of the technique in the design of automatic flight control systems which employ the human pilot as a performance assessor and failure detector are briefly discussed.

Hess, R. A.↗
NASA NTRS2008

Modeling and Optimization for Morphing Wing Concept Generation II: Morphing Wing Modeling and Structural Sizing Techniques - Part 1

This report documents a series of investigations to develop an approach for structural sizing of various morphing wing concepts. For the purposes of this report, a morphing wing is one whose planform can make significant shape changes in flight - increasing wing area by 50% or more from the lowest possible area, changing sweep 30 or more, and / or increasing aspect ratio by as much as 200% from the lowest possible value. These significant changes in geometry mean that the underlying load-bearing structure changes geometry. While most finite element analysis packages provide some sort of structural optimization capability, these codes are not amenable to making significant changes in the stiffness matrix to reflect the large morphing wing planform changes. The investigations presented here use a finite element code capable of aeroelastic analysis in three different optimization approaches -a "simultaneous analysis" approach, a "sequential" approach, and an "aggregate" approach.

Skillen, Michael D.↗
NASA NTRS1972

Optimum Three Impulse Trajectory Generator with Patched Conic Trajectory Model

Optimal multi-impulse trajectories were investigated as a nominal about which asymptotic expansion was used to obtain approximations of optimal low thrust trajectories. The work consisted of the analysis and description of an optimal 3-impulse trajectory program. A patched-conic trajectory model was specifically designed for compatibility with the subsequent addition of the low thrust expansion approximation.

Payne, M. H.↗
NASA NTRS1985

Box truss analysis and technology development. Task 1: Mesh analysis and control

An analytical tool was developed to model, analyze and predict RF performance of box truss antennas with reflective mesh surfaces. The analysis system is unique in that it integrates custom written programs for cord tied mesh surfaces, thereby drastically reducing the cost of analysis. The analysis system is capable of determining the RF performance of antennas under any type of manufacturing or operating environment by integrating together the various disciplines of design, finite element analysis, surface best fit analysis and RF analysis. The Integrated Mesh Analysis System consists of six separate programs: The Mesh Tie System Model Generator, The Loadcase Generator, The Model Optimizer, The Model Solver, The Surface Topography Solver and The RF Performance Solver. Additionally, a study using the mesh analysis system was performed to determine the effect of on orbit calibration, i.e., surface adjustment, on a typical box truss antenna.

Bachtell, E. E.↗
NASA NTRS2019

Surrogate Modeling and Optimization of a Combustor with an Interdigitated Flushwall Injector

Design and Analysis of Computer Experiments (DACE) methods are applied and used to perform surrogate modeling and optimization of a simplified combustor flowpath with an interdigitated flushwall injector. The objectives of the optimization are the thrust potential and combustion efficiency, which are evaluated across a range of flight Mach numbers, duct heights, spanwise spacings, and injection angles. The focus of this work is to highlight the application of a sequential learning approach, in order to learn about the responses of the objective functions over the design space and to identify local regions of interest for further analysis. This approach is contrasted to a previous effort where only a single sampling set was used to fit surrogate models and perform optimization. The optimal solutions resulting from the previous and present approaches are different, due to surrogate model-guided local refinement of the design space allowed by the sequential learning method. The values of the global error estimates between the previous and present approaches are comparable, but the sequential method proved more computationally cost-effective. Further refinement in the optimal regions might be needed to improve predictive capability of surrogate models and to obtain the optimal solutions sets.

Rajiv R Shenoy↗
NASA NTRS1977

Economic Benefits of Improved Information on Worldwide Crop Production: An Optimal Decision Model of Production and Distribution with Application to Wheat, Corn, and Soybeans

An optimal decision model of crop production, trade, and storage was developed for use in estimating the economic consequences of improved forecasts and estimates of worldwide crop production. The model extends earlier distribution benefits models to include production effects as well. Application to improved information systems meeting the goals set in the large area crop inventory experiment (LACIE) indicates annual benefits to the United States of $200 to $250 million for wheat, $50 to $100 million for corn, and $6 to $11 million for soybeans, using conservative assumptions on expected LANDSAT system performance.

Andrews, J.↗
NASA NTRS1978

A comparison of motor submodels in the optimal control model

Properties of several structural variations in the neuromotor interface portion of the optimal control model (OCM) are investigated. For example, it is known that commanding control-rate introduces an open-loop pole at S=O and will generate low frequency phase and magnitude characteristics similar to experimental data. However, this gives rise to unusually high sensitivities with respect to motor and sensor noise-ratios, thereby reducing the models' predictive capabilities. Relationships for different motor submodels are discussed to show sources of these sensitivities. The models investigated include both pseudo motor-noise and actual (system driving) motor-noise characterizations. The effects of explicit proprioceptive feedback in the OCM is also examined. To show graphically the effects of each submodel on system outputs, sensitivity studies are included, and compared to data obtained from other tests.

Lancraft, R. E.↗
NASA NTRS1982

An optimal control model approach to the design of compensators for simulator delay

The effects of display delay on pilot performance and workload and of the design of the filters to ameliorate these effects were investigated. The optimal control model for pilot/vehicle analysis was used both to determine the potential delay effects and to design the compensators. The model was applied to a simple roll tracking task and to a complex hover task. The results confirm that even small delays can degrade performance and impose a workload penalty. A time-domain compensator designed by using the optimal control model directly appears capable of providing extensive compensation for these effects even in multi-input, multi-output problems.

Baron, S.↗
NASA NTRS1991

Branch strategies - Modeling and optimization

The authors provide a common platform for modeling different schemes for reducing the branch-delay penalty in pipelined processors as well as evaluating the associated increased instruction bandwidth. Their objective is twofold: to develop a model for different approaches to the branch problem and to help select an optimal strategy after taking into account additional i-traffic generated by branch strategies. The model presented provides a flexible tool for comparing different branch strategies in terms of the reduction it offers in average branch delay and also in terms of the associated cost of wasted instruction fetches. This additional criterion turns out to be a valuable consideration in choosing between two strategies that perform almost equally. More importantly, it provides a better insight into the expected overall system performance. Simple compiler-support-based low-implementation-cost strategies can be very effective under certain conditions. An active branch prediction scheme based on loop buffers can be as competitive as a branch-target-buffer based strategy.

Dubey, Pradeep K.↗
NASA NTRS2009

Analysis of Sting Balance Calibration Data Using Optimized Regression Models

Calibration data of a wind tunnel sting balance was processed using a search algorithm that identifies an optimized regression model for the data analysis. The selected sting balance had two moment gages that were mounted forward and aft of the balance moment center. The difference and the sum of the two gage outputs were fitted in the least squares sense using the normal force and the pitching moment at the balance moment center as independent variables. The regression model search algorithm predicted that the difference of the gage outputs should be modeled using the intercept and the normal force. The sum of the two gage outputs, on the other hand, should be modeled using the intercept, the pitching moment, and the square of the pitching moment. Equations of the deflection of a cantilever beam are used to show that the search algorithm s two recommended math models can also be obtained after performing a rigorous theoretical analysis of the deflection of the sting balance under load. The analysis of the sting balance calibration data set is a rare example of a situation when regression models of balance calibration data can directly be derived from first principles of physics and engineering. In addition, it is interesting to see that the search algorithm recommended the same regression models for the data analysis using only a set of statistical quality metrics.

Ulbrich, Norbert↗
NASA NTRS2023

An Ensemble Neural Network Model for Predicting Rare-Earth Oxide and Silicate Heat Capacities at High Temperature

In this work, a neural network model was developed to predict the constant pressure heat capacity for materials in the rare-earth oxide—silica material space. Several model architectures were trained and tested on heat capacity data generated from first-principles density functional theory calculations. Hyperparameter optimization was performed, and the optimal model was selected for heat capacity predictions. The optimal model architecture was found to have a root-mean-squared error of 5.12 ± 3.37 J/mol-K. The optimal model architecture was then used in a bagging ensemble model trained using the leave-one-group-out method to provide error estimates for model predictions. The out-of-bag score for the ensemble model was 0.997. The predicted heat capacities agree well with the DFT and experimental results and were computed orders of magnitude faster than DFT simulations. Machine learning shows the potential to provide a suitable surrogate model for thermochemical property predictions for candidate environmental barrier coating materials but refining of input material features and model architectures could further improve accuracy for these models.

environmental barrier coatings↗