Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MoO3”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

51 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Achieving Stable Molybdenum Oxide Cathodes for Aqueous Zinc-Ion Batteries in Water-in-Salt Electrolyte

A layered MoO 3 material with large interlayer spacing represents a promising cathode for aqueous rechargeable Zn-ion batteries (ARZIBs), but the implementation of this material is limited due to the intrinsically low conductivity and poor structural stability. A 30 m ZnCl 2 water-in-salt electrolyte (WISE) was introduced to a MoO 3 nanobelt cathode for the first time, significantly increasing the stability of MoO 3 cathodes compared to those in 3 M ZnSO 4 and 3 M ZnCl2 electrolyte. The Zn/MoO 3 cell in WISE unambiguously demonstrated significantly improved rate performance delivering 349, 253, and 222 mAh/g at 100, 500, and 1000 mA/g, denoting a 2×, and 12× capacity increase of those achieved in 3 M electrolytes at 500 and 1000 mA/g, respectively. A capacity retention rate of 73% was achieved after (dis)charging at 100 mA/g for 100 cycles, and no obvious capacity fading was observed at higher current densities of 500 mA/g and 2A/g. A compilation of structural and morphological characterization was systematically performed to provide insight into the mechanisms of the improved performance in ZnCl 2 WISE for the MoO3 cathode materials. Specifically, our data collectively suggested that the drastic fading in 3M electrolytes can be attributed to the parasitic surface deposits on Zn originated from Mo dissolution and H 2 formation due to Zn corrosion and hydrogen evolution reaction (HER), which were significantly suppressed in the ZnCl 2 WISE. The direct visualization of these side reactions was achieved for the first time in the Zn-MoO 3 system, using an in situ optoelectrochemical measurement.

25 ENERGY STORAGE↗
DOE OSTI2024

Solution-based electrical doping of organic photovoltaics with non-fullerene acceptors facilitated by solvent vapor pre-treatment

Solution-based electrical doping of organic semiconductors using 12-molybdophosphoric acid (PMA) hydrate has been shown to allow p-type doping of conjugated polymers over a limited depth from the surface, enabling the fabrication of organic solar cells with a simplified device architecture. However, the doping level of certain conjugated polymers using PMA was found to be limited by the polymer film volume. Here, we report a modified PMA doping technique based on film volume expansion that is applicable to device fabrication, leading to hole-collecting layer-free non-fullerene organic photovoltaic devices, which exhibit a comparable photovoltaic performance to those with a commonly evaporated MoO3 hole-collecting layer.

Materials Science↗
DOE OSTI2020

Materials Data on Tl2Mo3SeO12 by Materials Project

Tl2(MoO3)3SeO3 crystallizes in the trigonal P31c space group. The structure is three-dimensional. Mo6+ is bonded to six O2- atoms to form distorted corner-sharing MoO6 octahedra. The corner-sharing octahedra tilt angles range from 32–47°. There are a spread of Mo–O bond distances ranging from 1.74–2.20 Å. There are two inequivalent Tl1+ sites. In the first Tl1+ site, Tl1+ is bonded in a 3-coordinate geometry to six O2- atoms. There are three shorter (2.96 Å) and three longer (3.18 Å) Tl–O bond lengths. In the second Tl1+ site, Tl1+ is bonded in a 6-coordinate geometry to six O2- atoms. There are three shorter (2.90 Å) and three longer (3.05 Å) Tl–O bond lengths. Se4+ is bonded in a trigonal non-coplanar geometry to three equivalent O2- atoms. All Se–O bond lengths are 1.74 Å. There are four inequivalent O2- sites. In the first O2- site, O2- is bonded in a distorted single-bond geometry to one Mo6+ and one Tl1+ atom. In the second O2- site, O2- is bonded in a 2-coordinate geometry to one Mo6+, one Tl1+, and one Se4+ atom. In the third O2- site, O2- is bonded in a 2-coordinate geometry to two equivalent Mo6+ and two Tl1+ atoms. In the fourth O2- site, O2- is bonded in a bent 150 degrees geometry to two equivalent Mo6+ atoms.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Materials Data on Rb2Mo3SeO12 by Materials Project

Rb2(MoO3)3SeO3 crystallizes in the hexagonal P6_3 space group. The structure is three-dimensional. there are two inequivalent Rb1+ sites. In the first Rb1+ site, Rb1+ is bonded in a 3-coordinate geometry to three equivalent O2- atoms. All Rb–O bond lengths are 3.05 Å. In the second Rb1+ site, Rb1+ is bonded in a 6-coordinate geometry to six O2- atoms. There are three shorter (2.98 Å) and three longer (3.06 Å) Rb–O bond lengths. Mo6+ is bonded to six O2- atoms to form distorted corner-sharing MoO6 octahedra. The corner-sharing octahedra tilt angles range from 32–46°. There are a spread of Mo–O bond distances ranging from 1.74–2.20 Å. Se4+ is bonded in a trigonal non-coplanar geometry to three equivalent O2- atoms. All Se–O bond lengths are 1.74 Å. There are four inequivalent O2- sites. In the first O2- site, O2- is bonded in a distorted single-bond geometry to one Rb1+ and one Mo6+ atom. In the second O2- site, O2- is bonded in a 3-coordinate geometry to one Rb1+, one Mo6+, and one Se4+ atom. In the third O2- site, O2- is bonded in a 2-coordinate geometry to one Rb1+ and two equivalent Mo6+ atoms. In the fourth O2- site, O2- is bonded in a bent 150 degrees geometry to two equivalent Mo6+ atoms.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Synthesis and Ultrahigh Pressure Compression of High-Entropy Boride (Hf0.2Mo0.2Nb0.2Ta0.2Zr0.2)B2 to 220 GPa

The high-entropy boride (Hf0.2Mo0.2Nb0.2Ta0.2Zr0.2)B2 material was synthesized under high-pressures and high-temperatures in a large-volume Paris-Edinburgh (PE) press from a ball-milled powder mix of HfO2, MoO3, Nb2O5, Ta2O5, ZrO2, carbon black, and boron carbide. The transformation process was monitored in situ by energy-dispersive x-ray diffraction with conversion starting at 1100 °C and completed by 2000 °C with the formation of a single hexagonal AlB2-type phase. The synthesized sample was recovered, powdered, and mixed with platinum pressure marker and studied under high pressure by angle-dispersive x-ray diffraction in a diamond anvil cell. The hexagonal AlB2-type phase of (Hf0.2Mo0.2Nb0.2Ta0.2Zr0.2)B2 was found to be stable up to the highest pressure of 220 GPa reached in this study (volume compression V/V0 = 0.70). The third order Birch-Murnaghan equation of state fit to the high-pressure data up to 220 GPa results in an ambient pressure unit cell volume V0=28.16±0.04 Å3, bulk modulusKo = 407 ± 6 GPa, pressure derivative of bulk-modulus K0′ = 2.73 ± 0.045 GPa. Our study indicates that this high-entropy boride (Hf0.2Mo0.2Nb0.2Ta0.2Zr0.2)B2 material is stable to ultrahigh pressures and temperatures and exhibit high bulk modulus similar to other incompressible transition metal borides like ReB2 and Os2B3.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Steam-Assisted Ammonolysis of MoO2 as a Synthetic Pathway to Oxygenated δ-MoN

A common route for the synthesis of molybdenum nitrides is through the temperature-programmed reaction of molybdenum oxides with NH3, or ammonolysis. In this work, the role of precursor phase, gas phase chemistry (impact of H2O), and temperature profile on the reaction outcome (700 °C) was examined, which resulted in varying amounts of MoO2, H2MoO5, and the nitride phases—cubic γ (nominally Mo2N) and hexagonal δ (nominally MoN). The phase fraction of the δ phase increased with precursor in the sequence MoO2 > MoO3 > H2MoO5. Steam in the reaction gas also favored the production of δ over γ, but with too much steam, MoO2 was obtained in the product. Synthesis conditions for obtaining nearly phase-pure δ were identified: MoO2 as the precursor, 2% H2O in the gas stream, and a moderate heating rate (3 °C/min). In situ X-ray diffraction provided insights into the reaction pathway. Extensive physico-chemical analysis of the δ phase, including synchrotron X-ray and neutron diffraction, electron microscopy, thermogravimetric analysis, X-ray photoelectron spectroscopy, and prompt gamma activation analysis, revealed its stoichiometry to be MoO0.108(8)N0.892(8)H0.012(5), indicating non-trivial oxygen incorporation. The presence of N/O ordering and an impurity phase Mo5N6 were also revealed, detectable only by neutron diffraction. Notably, a computationally predicted MoON phase (doi: 10.1103/PhysRevLett.123.236402), of interest due to its potential to display a metal-insulator transition, did not appear under any reaction condition examined.

Pandey, Shobhit↗
DOE OSTI2024

Selective CW Laser Synthesis of MoS2 and Mixture of MoS2 and MoO2 from (NH4)2MoS4 Film

Very recently, the synthesis of 2D MoS2 and WS2 through pulsed laser-directed thermolysis can achieve wafer-scale and large-area structures, in ambient conditions. In this paper, we report the synthesis of MoS2 and MoS2 oxides from (NH4)2MoS4 film using a visible continuous-wave (CW) laser at 532 nm, instead of the infrared pulsed laser for the laser-directed thermolysis. The (NH4)2MoS4 film is prepared by dissolving its crystal powder in DI water, sonicating the solution, and dip-coating onto a glass slide. We observed a laser intensity threshold for the laser synthesis of MoS2, however, it occurred in a narrow laser intensity range. Above that range, a mixture of MoS2 and MoO2 is formed, which can be used for a memristor device, as demonstrated by other research groups. We did not observe a mixture of MoS2 and MoO3 in the laser thermolysis of (NH4)2MoS4. The laser synthesis of MoS2 in a line pattern is also achieved through laser scanning. Due to of the ease of CW beam steering and the fine control of laser intensities, this study can lead toward the CW laser-directed thermolysis of (NH4)2MoS4 film for the fast, non-vacuum, patternable, and wafer-scale synthesis of 2D MoS2.

(NH4)2MoS4↗
DOE OSTI2022

Intercalation-Activated Layered MoO 3 Nanobelts as Biodegradable Nanozymes for Tumor-Specific Photo-Enhanced Catalytic Therapy

The existence of natural van der Waals gaps in layered materials allows them to be easily intercalated with varying guest species, offering an appealing strategy to optimize their physicochemical properties and application performance. Herein, we report the activation of layered MoO 3 nanobelts via aqueous intercalation as an efficient biodegradable nanozyme for tumor-specific photo-enhanced catalytic therapy. In this work, the long MoO 3 nanobelts are grinded and then intercalated with Na + and H 2 O to obtain the short Na + /H 2 O co-intercalated MoO 3–x (NH–MoO 3–x ) nanobelts. In contrast to the inert MoO 3 nanobelts, the NH–MoO 3–x nanobelts exhibit excellent enzyme-mimicking catalytic activity for generation of reactive oxygen species, which can be further enhanced by the photothermal effect under a 1064 nm laser irradiation. Thus, after bovine serum albumin modification, the NH–MoO 3–x nanobelts can efficiently kill cancer cells in vitro and eliminate tumors in vivo facilitating with 1064 nm laser irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Free‐Standing α‐MoO 3 / Ti 3 C 2 MXene Hybrid Electrode in Water‐in‐Salt Electrolytes

While transition‐metal oxides such as α‐MoO 3 provide high capacity, their use is limited by modest electronic conductivity and electrochemical instability in aqueous electrolytes. Two‐dimensional (2D) MXenes, offer metallic conductivity, but their capacitance is limited in aqueous electrolytes. Insertion of partially solvated cations into Ti 3 C 2 MXene from lithium‐based water‐in‐salt (WIS) electrolytes enables charge storage at positive potentials, allowing a wider potential window and higher capacitance. Herein, we demonstrate that α‐MoO 3 /Ti 3 C 2 hybrids combine the high capacity of α‐MoO 3 and conductivity of Ti 3 C 2 in WIS (19.8 m LiCl) electrolyte in a wide 1.8 V voltage window. Cyclic voltammograms reveal multiple redox peaks from α‐MoO 3 in addition to the well‐separated peaks of Ti 3 C 2 in the hybrid electrode. This leads to a higher specific charge and a higher rate capability compared to a carbon and binder containing α‐MoO 3 electrode. These results demonstrate that the addition of MXene to less conductive oxides eliminates the need for conductive carbon additives and binders, leads to a larger amount of charge stored, and increases redox capacity at higher rates. In addition, MXene encapsulated α‐MoO 3 showed improved electrochemical stability, which was attributed to the suppressed dissolution of α‐MoO 3 . The work suggests that oxide/MXene hybrids are promising for energy storage.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A study of in situ reduction of MoO 3 to MoO 2 by X-ray Photoelectron Spectroscopy

Results from X-ray Photoelectron Spectroscopy (XPS) of molybdenum oxide samples are presented to elucidate how Mo (VI) oxide evolves to Mo (IV) oxide upon heating of a MoO 3 sample. XPS data analysis techniques based on manipulation of spectra treated as vectors are shown and allow insights into intermediate phases of Mo oxide which suggest how the original oxide changes under the influence of heat but also supports an interpretation of as-received tetravalent Mo powders as multivalent materials. In particular, several new spectral components were observed and assigned to the Magnéli phase as well as MoO 3 domains that have been modified by the presence of X-rays or temperature. Finally, these assignments comprise a new method of data processing where sample modification is used to inform XPS data interpretation and differ from previous work where the linear relationship of the binding energy of molybdenum oxides has been used.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Controlling MoO 2 and MoO 3 phases in MoO x /CNTs nanocomposites and their application to anode materials for lithium-ion batteries and capacitors

Molybdenum oxides (MoO 2 and MoO 3 ) are attractive anode materials for Li- and Na- ion batteries. Although there have been extensive studies on them individually, systematic and comparative studies are still lacking. Here, we demonstrate a facile and straightforward synthesis method to control the phase and oxidation state in the MoO x /CNTs nanocomposites via hydrothermal reaction followed by heat-treatment. By changing the gas atmosphere during the annealing process, well-dispersed MoO 2 /CNTs and MoO 3 /CNTs nanocomposites are formed without altering their overall morphology. This strategy enables us to investigate the true structure-property correlation of MoO x /CNTs nanocomposites by comparing the structure and electrochemical properties of MoO 2 /CNTs and MoO 3 /CNTs. When tested as anode materials for lithium-ion batteries, both HT-MoO 2&3 /CNTs electrodes show much-improved cycling stability and rate performance compared to the rod-shaped bulk MoO 3 electrode. In situ Mo K-edge x-ray absorption spectroscopy (XAS) has been further employed to compare and elucidate Li + storage mechanisms of both electrodes. When employed to the negative electrode of a high-power lithium-ion capacitor (LIC), the LIC full-cell composed of HT-MoO 3 /CNTs negative and activated carbon positive electrodes demonstrates impressive energy and power densities (~ 90 Wh kg –1 with 2000 W kg –1 ) and excellent cycling stability (96.8 % capacity retention after 300 cycles), revealing the versatility of the MoO x /CNTs electrodes in energy applications.

25 ENERGY STORAGE↗
DOE OSTI2024

Chemical preintercalation of magnesium ions into ⍺-MoO 3 structure for improved electrochemical stability in Li-ion cells

Chemical preintercalation of layered materials, used as electrodes in intercalation-based energy storage devices, represents a promising strategy to enhance electrochemical stability and extend cycle life. However, standardized synthesis approaches for the chemical preintercalation of diverse ions into various layered materials are lacking, necessitating the development of specific synthesis routes for each ion and layered phase combination. In this study, we present the first successful demonstration of Mg 2+ ion chemical preintercalation into the interlayer region of α-MoO 3 , revealing its stabilizing effect during cycling in non-aqueous Li-ion cells. Using ethanol during hydrothermal treatment facilitated molybdenum reduction, which was critical for Mg 2+ ion preintercalation. Interestingly, we found that Mg preintercalation was accompanied by the incorporation of water. Mg-preintercalated α-MoO 3 exhibited enhanced charge storage capacity, electrochemical stability, and power capability compared to pristine α-MoO 3 electrodes. This improved performance is attributed to the structural stabilization provided by Mg 2+ pillars, which prevent undesirable phase transformations during repeated Li intercalation/deintercalation, and increased Li + ion diffusion due to the shielding of electrostatic interactions between electrochemically cycled ions and the α-MoO 3 lattice, enabled by structural water. In conclusion, our study offers new insights into developing chemical preintercalation synthesis approaches that can be broadly applied to a wide range of pillaring ions and layered material hosts.

25 ENERGY STORAGE↗
DOE OSTI2021

In Situ Polymerization of Polypyrrole and Polyaniline on the Surface of Magnetic Molybdenum Trioxide Nanoparticles: Implications for Water Treatment

Photocatalyst dissolution greatly diminishes the usability of photocatalysts in water treatments. Coating conductive polymers on the surface of photocatalysts can reduce dissolution without compromising the photocatalytic properties of the material. In this investigation, polypyrrole (PPy) and polyaniline (PANI) were used to coat two magnetic MoO 3 nanoparticles with different surface chemistries. The polymer-coated MoO 3 @Fe 3 O 4 nanoparticles were synthesized by optimizing the mole fractions of PPy or PANI, MoO 3 , and Fe 3 O 4 . The optimized PPy@ MoO 3 @Fe 3 O 4 (PMF1) and PANI@MoO 3 @Fe 3 O 4 (PMF2) resulted in 95.39 and 75.98% methylene blue dye removal, respectively. MoO 3 dissolutions of 4.12 and 5.6% were obtained for PMF1 and PMF2, respectively, demonstrating the reduced solubility of the coated nanoparticles as compared to their uncoated counterparts (7.87% for MF1 and 18.1% for MF2). In situ small-angle neutron scattering (SANS) was utilized to investigate the polymerization kinetics of PPy and PANI on nanoparticles. The results revealed that an increase in base material oxygen vacancies resulted in the reduction of both the polymer size and the polymerization rate. Furthermore, this study demonstrated that SANS provides valuable insights into the polymer growth mechanisms on nanoparticle surfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Elucidating the Competitive Hydrodeoxygenation of Lignin-Derived Oxygenates over Bulk MoO 3 Catalyst through Kinetic Analysis

Ambient pressure hydrodeoxygenation (HDO) of lignin-derived oxygenates over molybdenum oxide-based catalysts is an effective strategy to produce chemicals that can be directly integrated into our existing petrochemical infrastructure. Complexities pertaining to the simultaneous kinetic and mechanistic analysis of HDO have limited research endeavors to single-compound systems. Although valuable insight into the catalytic reaction has been gained through this approach, it provides limited understanding of the competitive adsorption behavior manifest in a realistic multioxygenate reaction environment. To address this shortcoming, simultaneous gas-phase acetone and anisole HDO was performed at 330 °C and ≤1 bar H 2 partial pressure over bulk MoO 3 . Propene, propane, and benzene were the HDO products formed, showing a similar product distribution to the single-compound system. Selectivity to propene and propane was ∼14 times higher than benzene, even at three times higher anisole partial pressure compared to acetone. A negative anisole HDO (−0.97 ± 0.22) rate order with varying acetone partial pressure suggested a strong inhibition effect on anisole HDO by acetone. Conversely, with increasing anisole partial pressure, a rate order of −0.07 ± 0.12 was observed for acetone HDO, implying a weak impact of anisole cofeed on acetone HDO. A kinetic-driven approach was taken to estimate the relative adsorption constants of the oxygenates. Acetone exhibited a 6.4 times higher adsorption propensity on the HDO active site than anisole. Relative adsorption constants for phenolics increased with increasing basicity of the oxygenate but decreased for aliphatic molecules, suggesting a volcano-shaped relationship. The results suggest the possibility of an optimal electron density around the molecule’s oxygen atom to maximize the molecule’s adsorption strength.

acid sites↗
DOE OSTI2022

The Dopamine Assisted Synthesis of MoO3/Carbon Electrodes With Enhanced Capacitance in Aqueous Electrolyte

A capacitance increase phenomenon is observed for MoO 3 electrodes synthesized via a sol-gel process in the presence of dopamine hydrochloride (Dopa HCl) as compared to α-MoO 3 electrodes in 5M ZnCl 2 aqueous electrolyte. The synthesis approach is based on a hydrogen peroxide-initiated sol-gel reaction to which the Dopa HCl is added. The powder precursor (Dopa) x MoO y , is isolated from the metastable gel using freeze-drying. Hydrothermal treatment (HT) of the precursor results in the formation of MoO 3 accompanied by carbonization of the organic molecules; designated as HT-MoO 3 /C. HT of the precipitate formed in the absence of dopamine in the reaction produced α-MoO 3 , which was used as a reference material in this study (α-MoO 3 -ref). Scanning electron microscopy (SEM) images show a nanobelt morphology for both HT-MoO 3 /C and α-MoO 3 -ref powders, but with distinct differences in the shape of the nanobelts. The presence of carbonaceous content in the structure of HT-MoO 3 /C is confirmed by FTIR and Raman spectroscopy measurements. X-ray diffraction (XRD) and Rietveld refinement analysis demonstrate the presence of α-MoO 3 and h-MoO 3 phases in the structure of HT-MoO 3 /C. The increased specific capacitance delivered by the HT-MoO 3 /C electrode as compared to the α-MoO 3 -ref electrode in 5M ZnCl 2 electrolyte in a −0.25–0.70 V vs. Ag/AgCl potential window triggered a more detailed study in an expanded potential window. In the 5M ZnCl 2 electrolyte at a scan rate of 2 mV s −1 , the HT-MoO 3 /C electrode shows a second cycle capacitance of 347.6 F g −1 . The higher electrochemical performance of the HT-MoO 3 /C electrode can be attributed to the presence of carbon in its structure, which can facilitate electron transport. Our study provides a new route for further development of metal oxides for energy storage applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗