Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructural characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Temperature-dependent mechanism on hardening mitigation in thermomechanically processed 800H alloys under neutron irradiation

Irradiation induced hardening is commonly observed in structural materials, and is often associated with the degraded ductility. This study explores the role of thermomechanical processing (TMP) in mitigating irradiation-induced hardening in Incoloy 800H. The radiation response of solution-annealed and TMP-treated samples was systematically investigated to elucidate the underlying mechanisms of hardening reduction. Neutron irradiation was performed on solution-annealed and TMP-treated samples at 359, 431, and 580 °C, revealing consistently lower hardening in TMP samples. Microstructural characterization compared dislocation loops, cavities, clusters, and precipitates to assess their contributions to hardening. The strengthening contributions from individual microstructural features were estimated, and the microstructure-derived yield strength is consistent with the hardness-converted yield strength. The microstructure–properties correlation revealed the temperature-dependent primary hardening mechanism: dislocation loops dominated at lower temperature, whereas Ni3(Al,Ti) γ′ precipitates were predominant at higher temperature. TMP reduced radiation-induced hardening through two mechanisms: (1) increased sink strength from dislocations and Ti(C,N) precipitates limited dislocation loop formation at lower temperatures, and (2) reduced Ti solute within the matrix in TMP samples suppressed γ′ precipitate formation at higher temperatures. These findings identify the mechanisms governing radiation-induced hardening across different temperatures, which lays the foundation for TMP optimization for the development of advanced radiation-tolerant materials.

Zhong, Weicheng [ORNL] (ORCID:0000000231589271)↗
DOE OSTI2026

Influence of microstructure and temperature on impact toughness of H13 steel produced by binder jet additive manufacturing

Binder Jet Additive Manufacturing (BJAM) is a promising manufacturing pathway to produce H13 steel dies and tooling with complex geometries for applications in high pressure aluminum die casting, hot stamping, and injection molding. While fully dense H13 coupons produced using BJAM have been subjected to detailed microstructure characterization, properties which are critical and relevant to the aforementioned applications, such as impact toughness, have not been reported. Here, this work evaluated the influence of microstructural characteristics and test temperature on the impact toughness of H13 produced by BJAM. Coupons were produced from three different powder size distributions (PSDs), with nominal powder size ranges of −22 μm, 10-32 μm, and 15-53 μm. Coupons were printed, sintered, hot isostatically pressed (HIPed), and heat treated by quenching and tempering. After HIPing, the measured porosities of the different PSDs were all less than 0.015 vol%. The −22 μm PSD BJAM material exhibited the best impact toughness of all three PSDs across the entire test temperature range from 25 to 400 °C, and also exhibited an ambient temperature impact toughness of 10.9 J at a hardness of 46 HRC, equivalent to minimum threshold requirements for premium grade H13. However, all three BJAM PSDs exhibited moderately lower impact toughness than premium grade wrought H13 from RT to 400 °C. We attribute this in part due to the very large prior-austenite grain (PAG) sizes near 400 μm and segregation from former liquid channels leading to greater amounts of carbide precipitation on PAG boundaries. Technical pathways for optimizing processing and chemistry of BJAM H13 to further improve impact toughness are discussed.

Binder jet additive manufacturing↗
DOE OSTI2025

Tailoring additive manufacturing to optimize dynamic properties in 316L stainless steel

With the advent of additive manufacturing, manipulation of typical microstructural elements such as grain size, texture, and defect densities is now possible at a faster time scale. While the processing–structure–property relationship in additive manufactured metals has been well studied over the past decade, little work has been done in understanding how this process affects the dynamic behavior of materials. We postulate that additive manufacturing can be used to alter the material microstructure and used to enhance its dynamic strength. In this work, 316L stainless steel (SS) was manufactured via selected laser melting and its microstructure was altered through changing build parameters like laser power, speed, and hatch spacing systematically. These samples were then subjected to spall recovery experiments to measure the spall strength and quantify the amount of damage as a function of build parameters. By mapping the spall strength as a function of build parameters, this work demonstrated that indeed additive manufacturing can be used to tailor the spall strength of 316L SS. This work also determined the optimum build parameters (laser power=195W; scanning speed=1083mm/s; hatch spacing=0.09mm; layer thickness=0.02mm) to obtain the highest spall strength and the least amount of total damage in 316L SS. Microstructural characterization of the pre- and post-mortem samples revealed that increased grain average misorientation and textural index were the main driving force behind this higher spall strength. This work aims to enhance microstructural engineering techniques to design materials with greater resistance to dynamic shock loading.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Additive manufacturing of AISI M2 tool steel by binder jetting (BJ): Investigation of microstructural and mechanical properties

The presented research demonstrates for the first time the successful processing of AISI M2 tool steel by binder jetting, a promising additive manufacturing technique capable of producing complex shapes with minimal residual stresses and isotropic properties. The optimal printing parameters were explored by varying processing parameters such as the binder saturation (45 %–105 %), binder set time (0 to 10 s), targeted bed temperature (50–60 °C), oscillator (2600–2750 rpm), recoater (20–28 mm/s), and roller speeds (200–300 rpm). Microstructural characterization and evaluation of mechanical properties of binder jetted parts were performed using x-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) to study their chemical composition, powder morphology, microstructure, carbide morphologies, relative density, hardness, compressive strength, and ductility. Two powder sizes (5 and 10 μm) were used, and sintering was performed at varying temperatures (1270, 1280, and 1300 °C) and durations (60 and 120 min), followed by a furnace, air, and water cooling. An optimum hardness of ~970 HV was obtained when parts were sintered at 1270 °C for 60 min, followed by water quenching. Impressive compressive strength of ~ 3580 MPa was observed in the sample sintered at 1280 °C for 60 min duration, followed by air cooling. Furnace-cooled parts showed the highest density of ~95 %, whereas the relative density of air- and water-cooled parts varied between ~91 to 93.50 %, respectively. The microstructure of sintered samples revealed the formation of M 6 C stable carbide, M 2 C metastable carbide, MC as a secondary carbide, and a-Fe matrix, which contributed to the observed increase in mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Elucidating microstructural evolution and hardness variation across friction self-piercing riveted Al-7055 using synchrotron X-ray scattering and advanced microscopy techniques

Friction self-piercing riveting (FSPR) is a unique hybrid joining technique that combines the advantages of mechanical interlocking, frictional heat, and solid-state joining (if metallurgically compatible) to produce crack free joints in high strength and/or low-ductility alloys at room temperature. Here, in the current study, Al-7055 sheets were joined using FSPR for lightweight automotive applications and significant microhardness variations were observed across the joint cross-section. A detailed microstructural characterization at multiple length scales was carried out using advanced electron microscopy and X-ray scattering techniques to provide a fundamental understanding of the process-structure-property relationships. The relative contributions of microstructural characteristics at various length scales (i.e., grain size, dislocation density, solute concentration, precipitate nature) to strengthening were estimated using existent formulations (i.e., Hall-Petch, Taylor, precipitate bypass/shear equations) and correlated to the observed microhardness values across different regions. Small-angle X-ray scattering and scanning transmission electron microscopy revealed significant changes in the size and volume fraction of precipitate species, i.e., GP-I Zones, η′, and Mg/Zn solute co-clusters, depending on the process region. It was observed that the dissolution of the small η′/GP-I zones (T ∼ 150–200 °C) in the heat-affected zone were the key reason for the hardness drop. Further, it was shown that solid-solution, dislocation, grain size and solute co-cluster strengthening played a key role in the thermo-mechanically affected zone and grain-refined zone (GRZ). Finally, these observations were leveraged along with the Zener-Holloman relationship and grain size in the GRZ to estimate the peak joining temperature of the GRZ (∼ 350 °C) near the steel rivet.

aluminum 7xxx alloy↗
DOE OSTI2026

Influence of the as-built microstructure on the recrystallization of an additively manufactured Inconel939 Ni-based superalloy

This study investigates the influence of the as-built microstructure on the recrystallization (RX) behavior and mechanical properties of the Ni-based superalloy Inconel 939 produced by laser powder bed fusion (PBF-LB/M). Two distinct as-built microstructures were obtained by varying the hatch distance (h d ): a columnar, strongly textured condition (h d =50, termed h d 50) and an equiaxed, weakly textured condition (h d =70, termed h d 70)). Both were subjected to nine solution treatments combining three temperatures (1100, 1150, and 1200 °C) and three holding times (1, 4, and 8 h). Comprehensive microstructural characterization was conducted to assess grain morphology, texture, grain boundary character, dislocation density, and precipitate distribution. Recrystallization was found to be significantly slower than in cast counterparts, requiring higher temperatures and longer times for completion. The initial microstructure plays a decisive role: full RX was achieved only in hd70 specimens after treatment at 1200 °C for 8 h, whereas hd50 samples exhibited delayed and incomplete RX under identical conditions. This behavior is attributed to the finer grain size and higher fraction of high-angle grain boundaries in hd70, which promote recrystallization. Mechanical testing revealed that hd70 samples subjected to a 1200 °C/8 h treatment followed by standard double ageing show higher yield and tensile strengths across the investigated temperature range than both printed and cast Inconel939 processed under conventional conditions, albeit with slightly reduced ductility. The enhanced mechanical performance is attributed to the larger grain size, which limits grain boundary sliding. These results demonstrate the critical importance of controlling the as-built microstructure and tailoring post-processing strategies to optimize high-temperature performance of PBF-LB/M Inconel939.

Inconel939↗
DOE OSTI2025

Charpy Impact Characterization of Surveillance Specimens Harvested from Palisades High Fluence A-60 Capsule

Located on the shores of Lake Michigan, the Palisades Nuclear Generating Station (PNGS) was a nuclear power plant that operated in Covert Township, Michigan. The plant had a single pressurized water reactor that produced electricity for the region. The PNGS was shut down in 2022 after more than four decades of service. The PNGS included in its surveillance program a surveillance capsule, designated A-60, containing specimens of a weld metal with nickel content of about 1.36 wt% and copper content of about 0.25 wt%. The capsule was removed from its surveillance position in early 1995 and has been resident in the spent fuel pool since that time. This capsule was irradiated to a fluence of 1.96×10 20 n/cm 2 (E>1MeV) that is equivalent for more than 150 effective full power years (EFPYs) for the US reactor pressure vessel (RPV) fleet. The material is also of special interest because of its very high nickel content and potential for development of NiMnSi (nickel-manganese-silicon) precipitates. Combination of very high fluence and very high Ni and Cu content makes the material in this capsule of great interest as benchmark for currently developing embrittlement trend curves (ETC) aiming to predict embrittlement at high fluences. Multi-year efforts by the Light Water Reactor Sustainability (LWRS) Program personnel from the Materials Research Pathway (MRP) to harvest this capsule finally succeeded in 2023. As a result, the Westinghouse Electric Company (WEC) through contract with Oak Ridge National Laboratory (ORNL) came to PNGS site, retrieved the A-60 capsule, brought it to WEC Churchill hot cell facility, opened the capsule and sent all surveillance specimens in the capsule to ORNL for future characterization by July 2023. Total of 9 tensile and 48 Charpy specimens were inventoried in the ORNL hot cells. Testing plan has been developed based on available specimens. It includes hardness, tensile, Charpy impact, Mini-CT fracture toughness testing, in-situ thermal annealing, and microstructural characterization, including Atom Probe Tomography (APT). Charpy impact testing has been completed and results are presented in this report. Moreover, negotiations with Pressurized Water Reactors Owners Group (PWROG) and Westinghouse resulted in Westinghouse donating to ORNL a piece of archive weld and base metal such that unirradiated characterization of these materials can be performed as part of this project. Comparison of measured hardening and embrittlement has been performed and data are compared to available large database.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Bulk nanocrystalline Al–Mg–Y alloys with amorphous grain boundary complexions display high strength and compressive plasticity

Although nanocrystalline alloys regularly exhibit high strengths, their use in structural applications often face challenges due to sample size limitations, unstable microstructures, and the limited ability to plastically deform. The incorporation of amorphous grain boundary complexions has been proposed to address these issues, by simultaneously stabilizing nanocrystalline grain structures for scale-up processing and improving alloy toughness. In the present study, the mechanical behavior of bulk nanocrystalline Al–Mg–Y is examined with macroscale compression testing, probing a length scale that is relevant to real-world structural applications. Bulk samples were fabricated via a simple powder metallurgy approach, with different hot-pressing temperatures and durations employed for consolidation in order to investigate microstructural and property evolution. All of the specimens contained primary face-centered cubic Al and secondary Al 4 C 3 and Al 3 Y phases, with the Al 3 Y particles exhibiting two populations of small equiaxed and larger elongated particles. Appreciable plasticity was measured along with high ultimate stresses over 800 MPa due to the presence of amorphous grain boundary complexions. Microstructural characterization of fracture surfaces revealed that the area fraction of dimpled regions increased with longer hot-pressing time. Most importantly, the elongated Al 3 Y particles formed regular cellular patterns with increasing hot-pressing time, delaying shear localization and significantly enhancing plasticity. The hierarchy present in the microstructure of the Al–Mg–Y alloy, from amorphous grain boundary complexions to secondary phases, gives rise to excellent bulk mechanical properties, which are attractive for structural applications.

Bulk nanocrystalline alloy↗
DOE OSTI2026

Additively manufactured refractory high-entropy alloys with superior radiation resistance

Refractory high-entropy alloys (RHEAs) are promising candidates for next-generation nuclear and high-temperature applications. Among many approaches to manufacture RHEAs, additive manufacturing (AM) represents the most recent and advanced metal manufacturing method which allows near-net-shape manufacturing to reduce material waste and post-processing time. However, performance of AM RHEAs under complex irradiation conditions remains largely unexplored. Here, in this study, we demonstrate for the first time the response of directed energy deposition (DED) AM quaternary RHEAs (HfTaVW, CrTaVW) subjected to sequential dual-beam ion irradiation, consisting of helium pre-implantation followed by high-dose heavy ion bombardment. Compositions of DED AM RHEAs were selected using Monte Carlo (MC) simulations based on a cluster expansion (CE) Hamiltonian parameterized by density functional theory (DFT). Post-irradiation microstructural characterization revealed that the AM RHEA maintained remarkable stability, with suppressed helium bubble growth and reduced defect accumulation compared to conventional alloys. Even at high doses (∼100 dpa), the alloy exhibited no void swelling, a low density of dislocation loops, and no evidence of severe degradation. These results highlight the intrinsic ability of AM-derived microstructures and multicomponent chemistry to synergistically mitigate irradiation effects. Our findings establish AM RHEAs as a class of materials with superior resistance to radiation damage under conditions relevant to advanced fusion and fission environments and demonstrate the importance of sequential ion beam studies in evaluating their long-term performance.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Geomechanical characterization of Rock Valley carbonates

In Rock Valley, Nevada, the USA, past earthquake sequences and shallow faulting in Paleozoic carbonates remain poorly understood. Carbonates are typically more ductile rocks that do not experience large stress drops or fracture coalescence, which contradicts previous observations in the region. As part of the Source Physics Experiment, an effort has been made to experimentally characterize the petrophysical and geomechanical properties of carbonates from Rock Valley. Well core and outcrop samples were used to determine the difference between shallow-buried Tertiary limestones and deeply buried Paleozoic limestones and dolostones. The carbonates possessed porosities between 3 and 9%, with V P and V S in the Tertiary carbonates around 2700 and 1800 m/s, respectively, and 6000 and 3100 m/s, respectively, in the Paleozoic carbonates. Microstructural characterization revealed that the Paleozoic carbonates contained significantly more pre-existing damage and alteration than the Tertiary carbonates, though the deformation varies from localized to diffuse. Unconfined Brazilian tests and triaxial tests with confining pressures between 0 and 50 MPa showed that, although samples all experienced failure, the dolostones typically failed at greater stresses and possessed greater E/ν ratios than the limestones. Furthermore, the Hoek–Brown failure criterion was used to construct failure envelopes with the compressive and tensile failure tests. Velocity, density, and porosity measurements were used to construct a hypothetical velocity-depth profile and compare the results with the theoretical petrophysical measurements. Using brittleness analysis, the likely failure conditions were determined to be low-porosity dolomitic rock for fault nucleation in the Paleozoic basement.

Brittleness↗
DOE OSTI2024

Insight into the interfacial microstructure and chemistry of hot isostatically pressed AA6061-AA6061 bonds for U-10Mo fuel cladding application

Here, in the present study, hot isostatic pressing (HIP) bonding was carried out using AA6061-AA6061 plates for U-10Mo monolithic fuel cladding application. HIP was performed at 560°C with an applied isostatic pressure of 103 MPa for 90 min. Interfacial microstructure characterizations were performed using scanning electron microscopy (SEM) combined with electron backscatter diffraction (EBSD) to quantify precipitate fractions and study recrystallization, grain growth, and orientation relationships across the interface. EBSD results confirmed that no interfacial grain growth occurred during the HIP process. Transmission electron microscopy (TEM) was also employed to quantify composition and identify phases of various precipitates and an oxide layer that formed at the interface during HIP bonding. Microstructural analyses revealed the formation of a large fraction of Mg 2 Si precipitate and a ~50 nm thick Mg-oxide layer at the interface. Further TEM analysis confirmed that the oxide layer was not continuous, and Mg 2 Al 2 O 5 oxide particles with an average size of 18 nm were present in the oxide layer. Finite element modeling analysis was performed to study the stress distribution at the interface during HIP processing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Creep Deformation and Damage Mechanisms in an Advanced High-Temperature Additively Manufactured Nickel-Base Superalloy

Abstract This research investigates the processing–structure–properties–performance relationship in a novel nickel-base superalloy, ABD ® -900AM, designed for extreme environments. Specifically tailored for additive manufacturing (AM), ABD ® -900AM maintains mechanical integrity at high temperatures and is comparable to other nickel-based superalloys with a 30–40% gamma-prime volume fraction. A comprehensive study was conducted using laser-beam powder bed fusion and electron-beam powder bed fusion methods. Factors such as heat treatment, porosity, build orientation, and hot isostatic pressing were evaluated to understand their effects on microstructure and mechanical performance. Microstructural characterization revealed significant differences in grain size and orientation across build processes and heat treatments. High-temperature mechanical testing indicated that grain size, heat treatment, and orientation significantly influence creep behavior. A super-solvus heat treatment led to recrystallization and grain growth, significantly improving creep properties compared to a near-solvus heat treatment. Various creep mechanisms were identified across different conditions, and creep rupture models were developed for each build process. Post-test microstructural analysis showed grain boundary damage, with differences in creep cavitation morphology under varying stress conditions. It was shown that MC carbides grow at the expense of gamma-prime near grain boundaries, leading to precipitate-free zones in specimens tested at higher temperatures. This study fills a significant gap in fundamental research by offering a deeper insight into the high-temperature mechanical behavior of additively manufactured nickel-base superalloys. It also explores critical research questions regarding the role of carbides and the significance of heat treatment. The insights gained enhance confidence in the industry adoption of ABD ® -900AM and similar alloys for high-temperature applications, bridging the knowledge gap and supporting the development of reliable AM processes for extreme environments.

Bridges, Alex (ORCID:000000030338759X)↗
DOE OSTI2026

Insights on carbon dioxide adsorption in a flexible 1-D coordination polymer from in situ X-ray scattering and density functional theory

A combination of in situ small-angle X-ray scattering (SAXS) microstructure characterization over scales ranging from 1 nm to 10 µm and powder X-ray diffraction (XRD) structure characterization under various gas/pressure/temperature conditions with density functional theory (DFT) calculations provides new insights for the CO2 sorption behavior of a one-dimensional porous coordination polymer: catena-bis­(di­benzoyl­methanato)(4,4′-bi­pyridyl)­nickel(II), denoted NiDBM-Bpy. The NiDBM-Bpy chains are held together by van der Waals forces, but the structure of guest-free NiDBM-Bpy is unsolved due to a lack of suitable crystals and high-quality powder XRD patterns. Nevertheless, SAXS and powder XRD can follow microstructural and structural changes as a function of gas pressure, composition and temperature. Both mixed-gas flow and static supercritical CO2 regimes are explored experimentally. DFT calculations are used to model the structural variation associated with XRD changes and hysteresis in the sorption isotherms. XRD and DFT calculations suggest that an orthorhombic Fddd structure with two CO2 per Ni emerges following a transition from the structure with lower molar volume and symmetry that exists without CO2 present.

Allen, Andrew J.↗
DOE OSTI2024

Invertible Temper Modeling using Normalizing Flows and the Effects of Structure Preserving Loss

Advanced manufacturing research and development is typically small-scale, owing to costly experiments associated with these novel processes. Deep learning techniques could help accelerate this development cycle but frequently struggle in small-data regimes like the advanced manufacturing space. While prior work has applied deep learning to modeling visually plausible advanced manufacturing microstructures, little work has been done on data-driven modeling of how microstructures are affected by heat treatment, or assessing the degree to which synthetic microstructures are able to support existing workflows. We propose to address this gap by using invertible neural networks (normalizing flows) to model the effects of heat treatment, e.g., tempering. The model is developed using scanning electron microscope imagery from samples produced using shear-assisted processing and extrusion (ShAPE) manufacturing. This approach not only produces visually and topologically plausible samples, but also captures information related to a sample’s material properties or experimental process parameters. We also demonstrate that topological data analysis, used in prior work to characterize microstructures, can also be used to stabilize model training, preserve structure, and improve downstream results. We assess directions for future work and identify our approach as an important step towards end-to-end deep learning system for accelerating advanced manufacturing research and development.

Howland, Sylvia↗
DOE OSTI2026

Variation in supercurrent connectivity and vortex pinning of state-of-the-art pulsed laser deposited RE Ba 2 Cu 3 O 7- x coated conductors

REBa 2 Cu 3 O 7-x (REBCO, RE: rare earth) coated conductors (CCs) suffer from great critical current I c differences between different manufacturers, I c variations within individual manufacturers, and often significant lengthwise fluctuations. The understanding of such variations is complicated by the lack of a direct correlation between I c and the critical current density J c . In fact, although J c is the fundamental property determined by the local vortex pinning landscape, I c is often limited by variable current blocking mechanisms. An important practical complexity is commercial practices of performing J c and I c evaluations based on I c at 77 K and self-field (sf), where connectivity variation dominates over vortex pinning variations. However, at higher fields and lower temperatures, vortex pinning becomes more complex and highly variable, making predictions of I c and J c at arbitrary temperature T, magnetic field H, and field orientation θ, quite uncertain. To address some aspects of this problem, we conducted detailed spool-to-spool performance characterization on recently manufactured REBCO CCs. Despite J c (77 K, sf) varies by only ∼11%, J c (77 K, 1 T) of its minimum and maximum (for H//ab-plane) show variations of ∼21% and ∼32%, respectively. This emphasizes the shortcoming in using J c (77 K, sf) as parameter for evaluating even the low field performance. An even more remarkable spool-to-spool J c variation of ∼68% was observed at 20 K and 15 T for H//ab-plane. To identify the origin of such lack of reproducibility we performed microstructural characterizations, which revealed, within the REBCO layer, large variation in the density of copper oxide (CuO x ) particles ranging from 0.1 to 2 μm in size. We believe that they play a decisive role in reducing the effective cross-section of the REBCO layer by not simply blocking current themselves, but also by nucleating off-axis REBCO grains, whose misoriented grain boundaries adversely impact REBCO grain-to-grain connectivity. The REBCO growth associated with high density CuO x particles also leads to the more disordered spatial arrangement of BaHfO 3 precipitate arrays, which, when self-aligning along the ab-planes, generate stronger pinning enhancing J c (H//ab) at all temperatures. In this way, we established that variations of both connectivity and vortex pinning are thus directly coupled. Our results also explain why the so-called ‘lift-factor’, typically defined by the ratio between I c (T, H) and I c (77 K, sf), frequently turns out to be unreliable.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Enhancing cold spray coatings: Microstructural dynamics and performance attributes of Inconel 625 with chromium carbide incorporation for hydropower applications

The incorporation of chromium carbide (CrC) particles into the cold spray (CS) process is known to mitigate nozzle clogging, although at the expense of deposition efficiency. This study explores the intricate microstructural changes induced by varying amounts of CrC powder (12.5 % and 6 %) in conjunction with Inconel-625 (Inc-625) powder. The deposition was carried out onto A27 cast steel under different CS parameters. Microstructural characterization, including detailed electron microscopy studies, reveals a complex yet structurally stable coating. Noteworthy features include grain fragmentation and a cellular structure enriched with Nb and Mo, with minimal plastic deformation of CrC in the matrix. The cold-sprayed coatings exhibit a significant (~4 times) increase in microhardness compared to the A27 substrate. Mechanical and cavitation erosion properties were systematically investigated. Coatings subjected to higher particle energy conditions with a gas pressure of 600 psi and gas temperature of 650 °C, demonstrated superior resistance to cavitation erosion. This resistance is attributed to a combination of factors, including microstructural characteristics and porosity. Altogether, the study provides valuable insights into the structural dynamics and performance of CS coatings enriched with CrC particles.

A27 cast steel↗
DOE OSTI2024

Effect of Heat Treatment on Microstructure and Mechanical Property of 316L Stainless Steel Produced by Laser Powder Bed Fusion

The advanced non-light water reactor designs (Gen IV reactors), including molten salt/ very high temperature/ sodium-cooled and lead-cooled fast reactors, typically operate at higher temperatures and more extreme radiation conditions than light water reactors. An intrinsic part of the deployment and progress of Gen IV reactor designs is selecting the most suitable structural material for a specific application. Additive manufacturing (AM), a fairly new process of making physical, three-dimensional objects from a computer design file, is going to completely change the way of design, build and certify nuclear systems. It offers a range of opportunities to produce complex geometries from existing materials, offers new routes for processing of previously difficult to process materials, allows for design of new high-performance materials, and finally facilitates hybridization of dissimilar materials. This emerging technology has successfully produced cars, wind turbine blade molds and even live cells. It could also open up big opportunities for the nuclear industry to quickly deploy technologies at a fraction of the cost. So far, AM techniques have been preliminarily applied in the field of nuclear reactors, including the classical parts such as the pressure vessel of a small reactor with 508-III steel, the bottom nozzle of a fuel assembly with 304L steel, the fuel cladding with zirconium alloy and the integrated impeller of a pump and the multi-channel valve body with 316L steel [6,7]. The AM applications for operating nuclear reactors started in auxiliary plant components and have slowly migrated to metallic reactors and core components, but many of these are not safety critical components. Although many parts used for nuclear reactors have been fabricated by AM techniques, practical applications in engineering are still a long way off due to the uncertainty factors focused on the processing, material properties, analysis methods and application standards, which feeds the safety and life-cycle of the nuclear reactor. Due to rapid, repeated heating and cooling during production, a high dislocation density was present in the AM material. This microstructure feature is unstable at elevated temperature while high temperature is one of the typical operation environments for nuclear reactors. Thus, it is important to understand the thermal effect on the microstructure of AM material. The objectives of this study are to investigate the effect of heat treatment on the microstructure and mechanical properties of 316L stainless steel produced by laser powder bed fusion additive manufacturing, and to determine an appropriate heat treatment practice that will be applied to the lightweight AM lattice-structured material with the same chemistry. The heat treatment study consisted of annealing the samples at a temperature range of 800 to 1200 oC with a 50 oC increment for different times (1-24 hours), followed by vacuum or air cooling. Microstructural characterization was carried out by Scanning Electron Microscope (SEM). Grain size and crystallographic orientation were investigated by Electron Backscatter Diffraction (EBSD). Vickers hardness tests with a 0.5 kg load were employed to determine the hardness of samples after different heat treatments. After heat treatment, the random crystallographic orientation was preserved, and the volume fraction of high-angle grain boundaries (grain boundary misorientation =15 oC) remained the same. The dislocation density decreased with annealing temperature due to recovery. The fine subgrain structures in the as-printed specimen were quite stable up to 1200 oC. Minimal recrystallization was observed up to 1200 oC. Recrystallization initiated only after 8.5 hours at 1200 oC. The SEM images did not show obvious dependence of microstructure on cooling rate. The hardness of the specimens decreased with increasing annealing temperature as a result of the decrease in dislocation density. It is interesting to note that the AM material showed very similar hardness to the wrought material when annealing at similar temperature, although the microstructures are very different. Annealing at 1050 oC for 1 hour followed by air cooling was selected as the heat treatment procedure for the lattice designed lightweight AM 316L material.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Utilizing machine learning to predict tensile ductility and yield strength of CoNiV-based multi-principal elements alloys

This study explores the use of machine learning (ML) as a computational tool to accelerate the design of multi-principal element alloys (MPEAs) with improved tensile elongation. An ML model was trained using available experimental data from the literature along with theoretically derived features to predict yield strength (YS) and ductility. A subset of ML-predicted compositions—CoNiVFe, CoNiVTi, CoNiVTiFe, and CoCrNiVTi—was synthesized and evaluated through tensile testing. The ML model underpredicted YS by approximately 20–30 % and overpredicted ductility by 60–70 % for Ti-containing alloys. Microstructural analysis revealed that Ti segregation at interdendritic regions contributed to early fracture, leading to discrepancies in ductility predictions. Ti segregation at these regions likely drives the increased YS due to segregation strengthening. In contrast, the CoNiVFe alloy showed good agreement with both experimental YS and elongation, with prediction errors of ∼10.2 % and ∼20.7 %, respectively. Microstructural characterization revealed minimal segregation in this alloy, suggesting that the ML model can reliably predict the properties of alloys with little to no segregation. These findings highlight the capability of ML in predicting YS with good accuracy but underscore its limitations in capturing defect-driven failure mechanisms such as segregation-induced embrittlement.

36 MATERIALS SCIENCE↗