Results for “Microstructural Refinement” — Page 3

DOE OSTI2025

Boron Nitride-Driven Strengthening of Aluminum Composites via Friction Stir Processing

Friction stir welding and processing (FSW/P) has emerged as an effective solid-state joining technique for fabricating metal matrix composites (MMCs), offering improved mechanical properties through refined microstructural evolution. In this study, an aluminum-boron nitride nanoparticle (Al-BNNP) composite was synthesized via FSW, and its indentation-based mechanical properties were systematically evaluated. Microhardness mapping across the weld cross-section revealed a progressive increase in hardness toward the stir zone (SZ), attributed to severe plastic deformation, dynamic recrystallization (DRX), and the reinforcing effect of BNNPs. Profilometry-based indentation plastometry (PIP) inferred yield strength (YS) demonstrates a 47.8% increase compared to the base metal (BM) and a 75% improvement compared to FSP pure aluminum reported in literature. This enhancement is attributed to strengthening mechanisms, including grain boundary pinning, load transfer, and increased dislocation density. The strain rate sensitivity (SRS) measurements at the nanoscale demonstrated a substantial decrease in the SZ, correlated with ultrafine grain structures and strong BNNP-matrix interactions. Activation volume analysis revealed a significant reduction in the SZ, suggesting that dislocation motion is increasingly restricted by dislocation-dislocation and dislocation-particle interactions. These findings suggest that incorporating BNNPs in FSW/P enables tailoring the microstructure without thermal degradation of the secondary particles, thereby significantly enhancing the mechanical performance of aluminum composites, particularly for structural applications in aerospace and automotive industries.

Aluminum↗

DOE OSTI2025

Ultrafast Oxygen Conduction in Sillén Oxychlorides

Oxygen ion conductors are crucial for enhancing the efficiency of various clean energy technologies, including fuel cells, solid oxide air batteries, electrolyzers, membranes, sensors, and more. In this study, a structure-similarity analysis of ≈62k oxygen-containing compounds identified the MBi 2 O 4 X (M = rare-earth element, X = halogen element) family as promising candidates for fast oxygen transport. Among these, LaBi 2 O 4 Cl is found as an ultrafast oxygen conductor with an ultralow migration barrier of 0.1 eV based on ab initio studies. Its 2D layered structure, featuring a “triple fluorite” layer, supports diffusion of both oxygen vacancies and interstitials. In addition to vacancy diffusion with a 0.1 eV barrier, ab initio studies show interstitial diffusion exhibits a modest barrier of 0.6–0.8 eV. Frenkel pairs are found to be the dominant defects in intrinsic LaBi 2 O 4 Cl, facilitating significant vacancy-mediated oxygen diffusion at elevated temperatures. With 2.8% oxygen vacancies, LaBi 2 O 4 Cl is predicted to achieve a conductivity of 0.3 S/cm at 25 °C in a single crystal. Experimental synthesis and characterization of polycrystalline LaBi 2 O 4 Cl and Sr-doped LaBi 2 O 4 Cl revealed conductivity exceeding that of YSZ and LSGM below 400 °C, with lower activation energies, achieving a total conductivity of 0.1−0.2 mS/cm at 300 °C. Here, while these results confirm its potential of fast oxygen transport, we suggest further experimental optimization of LaBi 2 O 4 Cl, including aliovalent doping and microstructure refinement, could significantly enhance its performance, facilitating fast oxygen conduction approaching room temperature.

Defects↗

DOE OSTI2026

Role of Si substitution in modulating the coercivity and magnetic anisotropy in Fe3CoB2 nanocrystallites

In this work, we report the impact of Si substitution on the structural and magnetic properties of Fe3CoB2 nanocrystallites as a rare-earth-free hard-magnet candidate. X-ray diffraction confirmed the formation of the tetragonal phase with an average crystallite size of ∼40 nm, while the transmission electron microscopy image revealed nanosized crystallites embedded in an amorphous matrix. Room-temperature Mössbauer spectra exhibited two sextets and two doublets, indicating magnetically ordered Fe sites in the tetragonal phase along with high-spin paramagnetic FeIII species in disordered regions. ZFC–FC magnetization curves displayed field-dependent blocking behavior, consistent with paramagnetic Fe species. Singular point detection measurements revealed a high anisotropy field of ∼10.7 kOe in the pristine Fe3CoB2, and systematically decreased with Si substitution. Magnetization measurements revealed a monotonic decrease in saturation magnetization with Si content, while coercivity was observed to increase, likely due to microstructural refinement. These results establish Fe3CoB2 as a rare-earth-free material with strong magnetic anisotropy, ideal for hard magnets.

Abbas, Hur [Department of Physics, University of T↗

DOE OSTI2025

Improving high temperature resilience of fiber sensor embedded smart components through laser shock peening

This study explores the use of laser shock peening (LSP) to enhance material properties and high-temperature performance of fiber-sensor-fused smart parts fabricated by additive manufacturing (AM) methods. Using embedded fiber sensors as distributed strain gauges, the study demonstrates that LSP can induce compressive strains of up to 130 µε on fiber embedded 1-mm below metal surfaces. The electron backscatter diffraction (EBSD) analysis shows that, with optimized LSP parameters, the metallic matrix undergoes substantial microstructural refinement, resulting in denser structures. Thermal cycling tests showed that the LSP process can increase fiber slippage temperatures by more than 50 °C. This work shows that the LSP process is an effective room-temperature process for enhancing both surface quality and increasing fiber slippage threshold under both thermal and mechanical stress.

Zhong, Shuda [University of Pittsburgh, PA (United↗

DOE OSTI2024

High Strength Aluminum Additive Manufacturing

High-strength aluminum alloys for elevated temperature applications are desirable to replace heavier and more expensive titanium alloys. However, most aluminum alloys lose a large fraction of their strength at temperatures above approximately 200°C. ORNL has designed DuAlumin-3D, an alloy with nominal composition Al-9Ce-4Ni-0.5Mn-1Zr (wt.%), which utilizes the high cooling rates in additive manufacturing (AM) to achieve a refined microstructure, and thermally stable mechanical properties. DuAlumin-3D was fabricated by laser powder bed fusion and tested for its tensile mechanical properties across a range of temperature, and for its room temperature high-cycle fatigue resistance. The alloy was tested in both the as-printed and heat treated conditions, and both parallel and perpendicular to the AM build direction. The alloy was found to have anisotropic mechanical behavior in the as-printed state, but the anisotropy significantly decreased (both for tensile and fatigue properties) following heat treatment. The tensile properties significantly out-performed benchmark wrought 2219-T61 across a wide temperature range. The room temperature fatigue performance was approximately similar to 2219-T61.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Materials Characterization, Prediction, and Control Project: Summary Report on Material Characterization, Part 1

The Pacific Northwest National Laboratory (PNNL) undertook the Materials Characterization, Prediction, and Control (MCPC) Laboratory Directed Research and Development Project to advance understanding of nuclear material processing and enable multifold acceleration in the development and qualification of new material systems in national security and advanced energy applications (Smith 2021). The MCPC Project executed research across three scientific vertices—material characterization, predictive modeling, and data analytics—with extensive support by a data curation and management team. The central technical objective in the MCPC Project was to improve the prediction and characterization of the process-structure-property relationships within the microstructurally refined region of stainless-steel samples prepared utilizing friction stir processing (FSP). Application of the FSP technique is well established at PNNL within the Solid Phase Processing capability through many years of investment across a range of materials and applications (PNNL 2024). Three distinct rounds of FSP experiments were performed by the experimental team, producing replicate samples utilizing across different nominal processing conditions (Condition IDs) listed in Table 1. The starting material on which FSP was applied was commercially available unprocessed stainless-steel type 316L material. Chosen processing conditions were very diverse, and some were intentionally chosen to produce defects. Several samples experienced tool breakage during experimentation, so a full set of three replicates was not produced for every nominal processing condition.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Materials Characterization, Prediction, and Control Project: Summary Report on Material Characterization, Part 2

The Pacific Northwest National Laboratory (PNNL) undertook the Materials Characterization, Prediction, and Control (MCPC) Laboratory Directed Research and Development Project to advance understanding of nuclear material processing and enable multifold acceleration in the development and qualification of new material systems in national security and advanced energy applications (Smith 2021). The MCPC Project executed research across three scientific vertices—material characterization, predictive modeling, and data analytics—with extensive support by a data curation and management team. The central technical objective in the MCPC Project was to improve the prediction and characterization of the process-structure-property relationships within the microstructurally refined region of stainless-steel samples prepared utilizing friction stir processing (FSP). Application of the FSP technique is well established at PNNL within the Solid Phase Processing capability through many years of investment across a range of materials and applications (PNNL 2024).

36 MATERIALS SCIENCE↗

DOE OSTI2024

Materials Characterization, Prediction, and Control Project: Summary Report on Material Characterization, Part 3

The Pacific Northwest National Laboratory (PNNL) undertook the Materials Characterization, Prediction, and Control (MCPC) Laboratory Directed Research and Development Project to advance understanding of nuclear material processing and enable multifold acceleration in the development and qualification of new material systems in national security and advanced energy applications (Smith 2021). The MCPC Project executed research across three scientific vertices—material characterization, predictive modeling, and data analytics—with extensive support by a data curation and management team. The central technical objective in the MCPC Project was to improve the prediction and characterization of the process-structure-property relationships within the microstructurally refined region of stainless-steel samples prepared utilizing friction stir processing (FSP). Application of the FSP technique is well established at PNNL within the Solid Phase Processing capability through many years of investment across a range of materials and applications (PNNL 2024).

36 MATERIALS SCIENCE↗

DOE OSTI2024

Materials Characterization, Prediction, and Control Project: Summary Report on Material Characterization, Part 4

The Pacific Northwest National Laboratory (PNNL) undertook the Materials Characterization, Prediction, and Control (MCPC) Laboratory Directed Research and Development Project to advance understanding of nuclear material processing and enable multifold acceleration in the development and qualification of new material systems in national security and advanced energy applications (Smith 2021). The MCPC Project executed research across three scientific vertices—material characterization, predictive modeling, and data analytics—with extensive support by a data curation and management team. The central technical objective in the MCPC Project was to improve the prediction and characterization of the process-structure-property relationships within the microstructurally refined region of stainless-steel samples prepared utilizing friction stir processing (FSP). Application of the FSP technique is well established at PNNL within the Solid Phase Processing capability through many years of investment across a range of materials and applications (PNNL 2024).

36 MATERIALS SCIENCE↗

DOE OSTI2025

An Additively Manufactured Fe-3Si Stator for a High-Performance Electrical Motor

Additive manufacturing (AM) has the potential to produce novel high-performance electrical machines, enabling the direct printing of complex shapes and the simultaneous processing of multiple feedstocks in a single build. We examined the properties and functional performance of Fe-3 wt.% Si materials that were printed via selective laser melting, machined down to thin laminates, and stacked to form a stator core of a prototype brushless permanent-magnet electrical motor. Big Area Additive Manufacturing of Nd2Fe14B (NdFeB)–polyphenylene sulfide (PPS) bonded magnets was performed, with them then being magnetized and used for the rotor. The magnetic, mechanical, and electrical properties of the as-printed and various heat-treated thin laminates and the back electromotive force (EMF) of the electrical motors at different rotational speeds were measured. The thin laminates exhibit a maximum relative permeability of 7494 at an applied field of 0.8 Oe and a core loss of about 20 W/lb at 60 Hz with the maximum induction of 15 kg. In addition to the demonstration of AM printing, motor assembly, and complete characterization of printed Fe-3 wt.% Si, this report highlights the areas of improvement needed in printing technologies to achieve AM built electrical motors and the need for isotropic microstructure refinements to make the laminates appropriate for high-mechanical-strength and low-loss rotational electrical devices.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Strong, ductile, and hierarchical hetero-lamellar-structured alloys through microstructural inheritance and refinement

The strength−ductility trade-off exists ubiquitously, especially in brittle intermetallic-containing multiple principal element alloys (MPEAs), where the intermetallic phases often induce premature failure leading to severe ductility reduction. Hierarchical heterogeneities represent a promising microstructural solution to achieve simultaneous strength−ductility enhancement. However, it remains fundamentally challenging to tailor hierarchical heterostructures using conventional methods, which often rely on costly and time-consuming processing. Here, we report a multiscale microstructural inheritance and refinement strategy to process “structural hierarchy precursors” in as-cast heterogeneous Al 0.7 CoCrFeNi MPEAs, which lead directly to a hierarchical hetero-lamellar structure (HLS) after simple rolling and annealing. Interestingly, it takes only 10 min of annealing time, two orders of magnitude less than that required to render the state-of-the-art properties during conventional processing of Al 0.7 CoCrFeNi, for us to achieve record-high strength−ductility combinations via the hierarchical HLS design that sequentially stimulates multiple unusual deformation and reinforcement mechanisms. In particular, the HLS-enabled high hetero-deformation-induced (HDI) internal stress triggers profuse <111>-type dislocations on over five independent slip systems in the supposedly brittle intermetallic phase and activates extensive stacking faults (SFs) and nanotwinning in the adjoining soft phase with a rather high SF energy. These unexpected, dynamically reinforcing hetero-deformation mechanisms across multiple length scales facilitate high sustained HDI strain hardening, along with a salient microcrack-mediated extrinsic ductilization effect, suggesting that the proposed microstructural inheritance and refinement strategy provides an efficient, fast, and low-cost approach to overcome the strength−ductility trade-off in a broad range of structural materials.

Science & Technology - Other Topics↗

DOE OSTI2022

The Trajectory of Additively Manufactured Titanium Alloys with Superior Mechanical Properties and Engineered Microstructures

Additive manufacturing (AM) plays a crucial role in the manufacturing and development of advanced materials including titanium alloys for engineering applications. During the last two decades, a great deal of effort has been devoted to print titanium parts with desired properties. However, due to presence of non-equilibrium/metastable phases, anisotropic microstructure, and various porosities in the printed titanium alloys, achieving an excellent combination of mechanical properties has been challenging. Here this review paper aims to provide a comprehensive overview of multiple post-process and in-process approaches to achieve enhanced strength-ductility combinations by microstructure engineering. Approaches such as addition of alloying elements/nucleants, multi-step post heat treatment, in-situ heat treatment, forced inter-pass cooling, in situ peening/rolling, hybridizing microstructure, high-intensity acoustic vibration, thermo-hydrogen refinement of microstructure, deliberately introducing lack of fusion defects with subsequent hot isostatic pressing are discussed in detail. Finally, we conclude by highlighting the challenges associated with each method and potential areas of improvement that can pave the way to develop reliable components with enhanced performance.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Toughening Sm–Co sintered magnets via microstructure modification with additives

We report the mechanical properties of the brittle Smsingle bondCo permanent magnets are of great practical significance. However, studies on the magnets have mostly focused on their magnetic properties. This paper reports the modified microstructure and refined unimodal grain size, enhanced flexural strength, and magnetic properties of Sm 2 (Co,Fe,Cu,Zr) 17 sintered magnets doped with La 2 O 3 , MgO, and CaF 2 fine particulates. The correlations between microstructure, phase composition, and mechanical and magnetic properties were studied. Doping of a small amount (e.g., 0.5–3 wt%) of La 2 O 3 , MgO, or CaF 2 fine particulates could significantly refine the unimodal grain sizes of the Smsingle bondCo magnets via the Zener pinning effect. Moreover, doping significantly improved the flexural strengths σ of the magnets. For example, the σ values of the magnets with 0.5 wt% MgO, 1 wt% La 2 O 3 , and 1 wt% CaF 2 were approximately 65%, 63%, and 42% higher than that of the reference magnet, respectively. Micromechanical simulations revealed that the fine particles of La 2 O 3 could deflect crack growth, while the CaF 2 particles could attract or arrest cracks during the fracture process. The mechanical strengthening effect was mainly due to grain size refinement. The Smsingle bondCo magnets with 0.5–1.5 wt% CaF2 and 0.5 wt% La 2 O 3 exhibited excellent magnetic properties while doping 1–3 wt% La2O3 and 0.5–3 wt% MgO deteriorated magnetic performance. The rational design of CaF 2 - or La 2 O 3 -doped microstructure can be an economical and effective method for producing toughened Sm–Co sintered magnets with high magnetic performance.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Mechanically robust high magnetic-performance Sm-Co sintered magnets through microstructure engineering

Samarium-cobalt (Sm-Co) sintered magnets have high magnetic energy densities, great resistance to demagnetization and corrosion, and excellent thermal stability in a wide temperature range (–50–550 °C). However, the utilization of these magnets is restricted by their brittleness. Based on micromechanical and the Zener pinning model, Sm-Co sintered magnets with improved mechanical properties have been designed and fabricated via microstructure engineering. A small amount of fine Sm 2 O 3 particulates (0–3 wt%) has been incorporated into Sm 2 (CoFeCuZr) 17 sintered magnets to refine the grain size by up to approximately 50% (from 45 to 22 µm) and narrow the grain size distribution. Doping with 3 wt% Sm 2 O 3 increased the flexural strength by 62% while maintaining magnetic performance. Both grain-refined unimodal microstructure and heterogeneous laminated coarse/fine grain microstructure were formed by strategically designed assemblies of Sm 2 O 3 -added Sm-Co powder feedstock mixtures. The technology is compatible with existing magnet manufacturing processes. Numerical micromechanics simulation indicates that the fracture is dominated by intragranular mode. The mechanical strength is mainly enhanced by the additive-induced grain refinement, while the small amount of Sm 2 O 3 addition has a small direct positive contribution. Finally, these magnets will be more cost-effective, efficient, and robust for various functional applications.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Nucleation and growth of α phase in a metastable β-Titanium Ti-5Al-5Mo-5V-3Cr alloy: Influence from the nano-scale, ordered-orthorhombic O" phase and α compositional evolution

We investigated the nucleation and growth of α precipitates in the presence of nano-scale, titanium-rich, ordered-orthorhombic O" precipitates formed during heating at 5 °C/min to 400 °C in a metastable β-Ti alloy, Ti-5Al-5Mo-5V-3Cr. The O" precipitates are found to assist α nucleation by serving as preferential nucleation sites. In the very initial stages of its precipitation, the α phase is found to have formed via a coupled diffusional-displacive mode as titanium-rich plates. At this stage, aluminum partitions equally between the β matrix and the growing α precipitates, but slowly diffuses up-hill into the α phase during isothermal aging at 400 °C for 15 h. The interplay between such pre-formed metastable phases and α can be exploited to tailor the microstructure, by refining the α distribution, and consequently improve the mechanical properties of β-Ti alloys. Finally, our work paves the way for exploiting this cascade of metastable phases for further microstructural engineering of β-Ti alloys.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Fabrication of thin-walled tubes from alloy 602 CA using shear assisted processing and extrusion

Thin-walled tube is usually produced seamlessly via an expensive multi-step process or via welding of thin sheets but at reduced performance. To overcome the current process and performance inefficiencies, advanced manufacturing methods need to be investigated. In this investigation, shear assisted processing and extrusion (ShAPE) was used to fabricate thin-walled Inconel 602 tube in a single-step. Tubes measuring 0.83 m length with a 12 mm outer diameter and 1 mm wall thickness were fabricated with an average surface roughness, Ra of 1.6 µm and Rz of 15 µm. Tensile testing of tubes in the as-fabricated condition showed strength increases of 4-35% over current offerings while maintaining or improving elongation. Electron microscopy analysis revealed the recrystallized microstructure with refined inter- and intra-granular carbides. Preliminary results obtained in this investigation shows the feasibility of producing thin-wall high temperature tube in single-step via ShAPE. This achievement marks a significant step towards manufacturing larger diameter nickel alloy tubes for the U.S. Department of Energy’s Waste Treatment and Immobilization Plant.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Strong‐Yet‐Ductile Eutectic Alloys Employing Cocoon‐Like Nanometer‐Sized Dislocation Cells

Abstract Eutectic alloys (EAs) with superior fluidity are known to be the easiest to cast into high‐quality ingots, making them the alloys of choice for making large‐sized structural parts. However, conventional EAs (CEAs) have never reached strength–ductility combinations on par with the best in other alloy categories. Via thermomechanical processing of cast Ni‐32.88wt%Fe‐9.53wt%Al CEAs, a cocoon‐like nano‐meshed (as fine as 26 nm) network of dislocations (CNN‐D) is produced via recovery annealing, through the rearrangement of cold‐work‐accumulated dislocations anchored by dense pre‐existing nanoprecipitates. In lieu of traditional plasticity mechanisms, such as TWIP and TRIP, the CNN‐D is particularly effective in eutectic lamellae with alternating phases, as it instigates nanometer‐spaced planar slip bands that not only dynamically refine the microstructure but also transmit from the FCC (face‐centered‐cubic) layers into the otherwise brittle B2 layers. These additional mechanisms for strengthening and strain hardening sustain stable tensile flow, resulting in a striking elevation of both strength and ductility to outrank not only all previous CEAs, but also the state of the art—additively manufactured eutectic high‐entropy alloys. The CNN‐D thus adds a novel microstructural strategy for performance enhancement, especially for compositionally complex alloys that increasingly make use of nanoprecipitates or local chemical order.

Chemistry↗

DOE OSTI2021

Microstructural evolution in Cu-Nb processed via friction consolidation

Immiscible alloys, whether in well-mixed or layered forms, are of increasing interest based on their novel structural and functional properties, such as enhanced thermal stability against grain growth or radiation-induced defect trapping at the interfaces. To address the need for new approaches to tailor microstructures, the microstructural development of an immiscible Cu-Nb alloy processed via friction consolidation of elemental powders is investigated. Friction consolidation is a solid-phase processing technique that imparts severe plastic strain into a deforming volume resulting in elevated temperatures below the melting temperature of the alloy. Two distinct processing pathways were chosen to understand the effect of thermomechanical conditions on the final microstructure. The microstructure was characterized using scanning electron microscopy, scanning transmission electron microscopy, and X-ray diffraction techniques. Path 1 exhibited larger strain, strain rate, and temperature as compared with path 2. In path 1, agglomerated Nb particles were present in the recrystallized ultrafine-grained Cu matrix, while in path 2 extremely fine and dispersed Nb particles were present in a highly deformed Cu matrix. In both pathways, supersaturation of Cu in Nb lattices was noted, but not vice-versa. The asymmetry in mixing is explained based on deformation-based, thermodynamic and kinetic factors. These findings provide a pathway for creation of novel tailored microstructures and improved properties in any number of binary immiscible alloy systems.

Cu-Nb alloys, Microstructural refinement, Friction↗