Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Matrix completion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

A pad perturbation method for the dynamic coefficients of tilting-pad journal bearings

A pad assembly method for analyzing tilting-pad bearings is presented. The method results in the complete coefficient matrix for a tilting-pad bearing; the matrix is independent of the pad inertia, the pitch frequency and the number of degrees of freedom of the pad. A pad assembly method is used because it allows the collection of more bearing data with less computer time than a brute force iterative procedure. The results given show the complete dynamical matrices for a five-pad tilting-pad bearing both including and ignoring the damping effects of the unloaded (top) pads. For a symmetrical tilting-pad bearing the reduced cross-coupling coefficients are zero when the moment of inertia of the pad is ignored.

Allaire, P. E.↗
NASA NTRS1976

Monotectic and syntectic alloys experiment MA-044

The flight test furnace run of the monotectic and syntectic alloys experiment was successfully performed during the Apollo Soyuz Test Project mission. All three experiment cartridges were returned intact. A second ground based test was conducted after the mission to provide one g samples with an equivalent thermal history. The examinations of all flight and ground based cartridges and ampoules have been completed. Encouraging results have been obtained in the preliminary analysis of one flight aluminum antimonide sample as compared to ground based and prototype test counterparts. In terms of reduction of the unwanted second phase, the low g sample shows a homogeneity improvement by a factor of 5 to 20. Preliminary examination of one lead zinc flight sample shows a dispersion of lead in the zinc matrix. However, complete homogenization of the material did not occur. A thermal analysis of flight data shows that the average soak temperature for the head zinc ampoules was 20 C lower than planned but 35 C above the published consolute temperature..

Ang, C. Y.↗
NASA NTRS1981

Modeling of photodegradation in solar cell modules of substrate and superstrate design made with ethylene-vinyl acetate as pottant material

The rates of hydrogen abstraction by peroxy radicals were proven to be too slow for significant oxidation of the alkane substrate to be important. The numerical procedure, independent of our particular data base was verified by reproducing concentration time profiles for a model reaction set describing the cesium flare system in the upper atmosphere. Simulation was identical to that given in the literature. Experimental verification of the data base is to be attempted by weatherometry studies in the coming year. Work on the new diagnostic techniques was completed. The adapted automated viscometer was demonstrated to be an efficient and reliable tool for routine measurements of viscosity (molecular weight) changes in solid samples after batch solutions have been made up. The laser photolysis GC method for monitoring extremely low levels of oxidation in polymers proved to be impractical because the yields of carbon monoxide were too low for quantification. Much progress was made with the computer model. The reaction matrix was completely revised, resulting in a new scheme of 31 reactions and time, lifetimes in excess of ten years. The results to date lead us to some tentative observations.

Somersall, A. C.↗
NASA NTRS2001

Polymer Matrix Composite Lines and Ducts

Since composite laminates are beginning to be identified for use in reusable launch vehicle propulsion systems, a task was undertaken to assess the feasibility of making cryogenic feedlines with integral flanges from polymer matrix composite materials. An additional level of complexity was added by having the feedlines be elbow shaped. Four materials, each with a unique manufacturing method, were chosen for this program. Feedlines were to be made by hand layup (HLU) with standard autoclave cure, HLU with electron beam cure, solvent-assisted resin transfer molding (SARTM), and thermoplastic tape laying (TTL). A test matrix of fill and drain cycles with both liquid nitrogen and liquid helium, along with a heat up to 250 F, was planned for each of the feedlines. A pressurization to failure was performed on any feedlines that passed the cryogenic cycling testing. A damage tolerance subtask was also undertaken in this study. The effects of foreign object impact to the materials used was assessed by cross-sectional examination and by permeability after impact testing. At the end of the program, the manufacture of the electron beam-cured feedlines never came to fruition. All of the TTL feedlines leaked heavily before any cryogenic testing, all of the SARTM feedlines leaked heavily after one cryogenic cycle. Thus, only the HLU with autoclave cure feedlines underwent the complete test matrix. They passed the cyclic testing and were pressurized to failure.

Nettles, A. T.↗
NASA NTRS1995

EDTA-insoluble, calcium-binding proteoglycan in bovine bone

A calcium ion precipitable, trypsin-generated proteoglycan fragment has been isolated from the demineralized, EDTA-insoluble matrices of bone. The demineralized matrix was completely digested with trypsin, increasing concentrations of CaCl2 were added to the supernatant, and the resulting precipitates were analyzed. The amount of precipitate gradually increased with higher concentrations of calcium and was reversibly solubilized by EDTA. After molecular sieve and anion exchange chromatography, a proteoglycan-containing peak was obtained. Immunochemical analysis showed that this peak contained chondroitin 4-sulfate and possibly keratan sulfate. Amino acid analysis showed that this proteoglycan contained high amounts of aspartic acid/asparagine (Asx), serine (Ser), glutamic acid/glutamine (Glx), proline (Pro), and glycine (Gly); however, it contained little leucine (Leu) which suggests that it is not a member of the leucine-rich small proteoglycan family. In addition, significant amounts of phosphoserine (P-Ser) and hydroxyproline (Hyp) were identified in hydrolysates of this fraction. A single band (M(r) 59 kDa) was obtained on SDS-PAGE that stained with Stains-all but not with Coomassie Brilliant Blue R-250. If bone powder was trypsinized prior to demineralization, this proteoglycan-containing fraction was not liberated. Collectively, these results indicate that a proteoglycan occurs in the demineralized matrix that is precipitated with CaCl2 and is closely associated with both mineral and collagen matrices. Such a molecule might facilitate the structural network for the induction of mineralization in bone.

NASA Program Space Physiology and Countermeasures↗
DOE OSTI2023

Measurement of the CMB temperature power spectrum and constraints on cosmology from the SPT-3G 2018 T T , T E , and E E dataset

We present a sample-variance-limited measurement of the temperature power spectrum ( T T ) of the cosmic microwave background using observations of a ∼ 1500 deg 2 field made by the SPT-3G in 2018. We report multifrequency power spectrum measurements at 95, 150, and 220 GHz covering the angular multipole range 750 ≤ ℓ < 3000 . We combine this T T measurement with the published polarization power spectrum measurements from the 2018 observing season and update their associated covariance matrix to complete the SPT-3G 2018 T T / T E / E E dataset. This is the first analysis to present cosmological constraints from SPT T T , T E , and E E power spectrum measurements jointly. We blind the cosmological results and subject the dataset to a series of consistency tests at the power spectrum and parameter level. We find excellent agreement between frequencies and spectrum types and our results are robust to the modeling of astrophysical foregrounds. We report results for Λ CDM and a series of extensions, drawing on the following parameters: the amplitude of the gravitational lensing effect on primary power spectra A L , the effective number of neutrino species N eff , the primordial helium abundance Y P , and the baryon clumping factor due to primordial magnetic fields b . We find that the SPT-3G 2018 T T / T E / E E data are well fit by Λ CDM with a probability to exceed of 15%. For Λ CDM , we constrain the expansion rate today to H 0 = 68.3 ± 1.5 km s - 1 Mpc - 1 and the combined structure growth parameter to S 8 = 0.797 ± 0.042 . The SPT-based results are effectively independent of Planck, and the cosmological parameter constraints from either dataset are within < 1 σ of each other. The addition of temperature data to the SPT-3G T E / E E power spectra improves constraints by 8–27% for each of the Λ CDM cosmological parameters. When additionally fitting A L , N eff , or N eff + Y P , the posteriors of these parameters tighten by 5–24%. In the case of primordial magnetic fields, complete T T / T E / E E power spectrum measurements are necessary to break the degeneracy between b and n s , the spectral index of primordial density perturbations. We report a 95% confidence upper limit from SPT-3G data of b < 1.0 . The cosmological constraints in this work are the tightest from SPT primary power spectrum measurements to date and the analysis forms a new framework for future SPT analyses.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1968

Random access-random release relay switching matrix

XY relay switching matrix provides complete random access and random release of 400 points. A mercury-wetted bistable relay with independent set and reset coils is the unique feature associated with each point.

Carter, J. A.↗
NASA NTRS1980

Errors incurred in a plane-wave-type expansion of a Gaussian beam

The multipole expansion obtained by Morita et al. (1968) of the Gaussian laser beam used to levitate an aerosol particle in order that its complete phase matrix may be measured is compared with that of Tsai and Pogorzelski (1975) in order to demonstrate the effect of the incorrect expansion used by Morita. Errors incurred by the use of an equation in which one side satisfies the scalar wave equation while the other side does not and can be reduced to a plane wave amplitude are calculated as functions of the inverse of the wave number times the beam waist, the wave number times the radial spherical coordinate and the angular spherical coordinate. Errors on the order of a few percent, considered undetectable are obtained in the squared-field amplitudes due to the expansion, however, they are found to become significant (several tens of percent) when the angle is zero. It is concluded that the expansion of Morita should only be used in the regions where the spherical angle is less than 0.01 and its product with the wave number and the radial spherical coordinate is less than unity.

Kattawar, G. W.↗
NASA NTRS1985

Calculations of atomic processes in Fe XVII

A synoptic study has been made of the neon-like ion Fe XVII in order to improve knowledge of its line production in high-temperature, low-density plasmas. The following were computed: (1) distorted wave, electron collision strengths from the ground level to all 88 levels with one n = 3 - or n = 4 electron; (2) a complete cascade matrix; (3) the contribution of resonances to the n = 3 level population rates; and (4) the resulting X-ray and EUV line emission coefficients as functions of temperature between T = 10 to the 5.6 and T = 10 to the 8.4 K. Results are presented for typical population rates, line emission coefficients fitted with a useful formula for spectrum calculations, and the dielectronic recombination rate.

Smith, B. W.↗
NASA NTRS1986

Imaging radar polarimetry from wave synthesis

It was shown that it is possible to measure the complete scattering matrix of an object using data acquired on a single aircraft pass, and can combine the signals later in the data processor to generate radar images corresponding to any desired combination of transmit and receive polarization. Various scattering models predict different dependence on polarization state of received power from an object. The imaging polarimeter permits determination of this dependence, which is called the polarization signature, of each point in a radar image. Comparison of the theoretical predictions and observational data yield identification of possible scattering mechanisms for each area of interest. It was found that backscatter from the ocean is highly polarized and well-modeled by Bragg scattering, while scattering from trees in a city park possesses a considerable unpolarized component. Urban regions exhibit the characteristics expected from dihedral corner reflectors and their polarization signatures are quite different from the one-bounce Bragg model.

Zebker, Howard A.↗
NASA NTRS1986

Imaging radar polarimetry from wave synthesis

It is shown that it is possible to measure the complete scattering matrix of an object using data acquired on a single aircraft pass, and combine the signals later in the data processor to generate radar images corresponding to any desired combination of transmit and receive polarization. Various scattering models predict different dependence on polarization state of received power from an object. The imaging polarimeter permits determination of this dependence, the polarization signature, of each point in a radar image. Comparison of predictions and observational data reveals scattering mechanisms for each area of interest. Backscatter from the ocean is highly polarized and well-modeled by Bragg scattering, while scattering from trees in a city park possesses a considerable unpolarized component. Urban regions exhibit the characteristics expected from dihedral corner reflectors, and their polarization signatures are quite different from the on-bounce Bragg model.

Zebker, H. A.↗
NASA NTRS1988

Multifrequency imaging radar polarimetry: Depolarisation of radar echoes at three wavelengths

It is shown that high resolution imaging radar polarimeters can describe depolarization effects in great detail by measuring the complete Stokes matrix for small regions on the Earth's surface, permitting to distinguish between coherent polarization transformation by the surface and diffuse interactions that randomize the polarization state of the received wave. Multiwavelength polarimeter observations of a variety of types of terrain, including images of the coherent and diffuse parts of the received signal are presented. The diffuse image, in particular, is highly indicative of small-scale surface roughness, an effect illustrated by analyzing a set of polarimeter images acquired over lava fields of varying roughness.

Zebker, H. A.↗
NASA NTRS1990

The unpolarized component in polarimetric radar observations of forested areas

A polarimetric radar measures the complete scattering matrix of a target. For the forest and other natural targets, the average return is, in general, partially polarized. Conditions on the second-order statistics of the scattering matrix under which the return is fully polarized are derived, and it is shown that these conditions are connected with the eigenvalues of the covariance matrix. The result of this analysis is a set of three quantities which indicate the ability of a scatterer to generate an unpolarized component. These quantities for forested areas are shown.

Durden, Stephen L.↗
NASA NTRS1990

Time-dependent wave-packet method for the complete determination of S-matrix elements for reactive molecular collisions in three dimensions

An alternative time-dependent wave-packet method for treating three-dimensional gas phase reactive atom-diatom collisions is presented. The method employs a nonreactive body-frame wave packet propagation procedure, made possible by judicious use of absorbing optical potentials, a novel scheme for interpolating the wave function from coordinates in one arrangement to those in another and the fact that the time-dependent Schroedinger equation is an initial-value problem. The last feature makes possible a computationally viable and accurate procedure for changing from one arrangement's coordinates to another. In addition, the method allows the determination of S-matrix elements over a wide range of energies from a single wave-packet propagation. The method is illustrated by carrying out detailed calculations of inelastic and reactive scattering in the H + H2 system using the Liu-Siegbahn-Truhlar-Horowitz potential surface.

Judson, Richard S.↗
NASA NTRS1992

A new pre-loaded beam geometric stiffness matrix with full rigid body capabilities

Space structures, such as the Space Station solar arrays, must be extremely light-weight, flexible structures. Accurate prediction of the natural frequencies and mode shapes is essential for determining the structural adequacy of components, and designing a controls system. The tension pre-load in the 'blanket' of photovoltaic solar collectors, and the free/free boundary conditions of a structure in space, causes serious reservations on the use of standard finite element techniques of solution. In particular, a phenomenon known as 'grounding', or false stiffening, of the stiffness matrix occurs during rigid body rotation. The authors have previously shown that the grounding phenomenon is caused by a lack of rigid body rotational capability, and is typical in beam geometric stiffness matrices formulated by others, including those which contain higher order effects. The cause of the problem was identified as the force imbalance inherent in the formulations. In this paper, the authors develop a beam geometric stiffness matrix for a directed force problem, and show that the resultant global stiffness matrix contains complete rigid body mode capabilities, and performs very well in the diagonalization methodology customarily used in dynamic analysis.

Bosela, P. A.↗
NASA NTRS1992

Multiresolution image gathering and restoration

In this paper we integrate multiresolution decomposition with image gathering and restoration. This integration leads to a Wiener-matrix filter that accounts for the aliasing, blurring, and noise in image gathering, together with the digital filtering and decimation in signal decomposition. Moreover, as implemented here, the Wiener-matrix filter completely suppresses the blurring and raster effects of the image-display device. We demonstrate that this filter can significantly improve the fidelity and visual quality produced by conventional image reconstruction. The extent of this improvement, in turn, depends on the design of the image-gathering device.

Fales, Carl L.↗
NASA NTRS2000

Asymptotic Solutions for Optical Properties of Large Particles with Strong Absorption

For scattering calculations involving nonspherical particles such as ice crystals, we show that the transverse wave condition is not applicable to the refracted electromagnetic wave in the context of geometric optics when absorption is involved. Either the TM wave condition (i.e., where the magnetic field of the refracted wave is transverse with respect to the wave direction) or the TE wave condition (i.e., where the electric field is transverse with respect to the propagating direction of the wave) may be assumed for the refracted wave in an absorbing medium to locally satisfy the electromagnetic boundary condition in the ray tracing calculation. The wave mode assumed for the refracted wave affects both the reflection and refraction coefficients. As a result, a nonunique solution for these coefficients is derived from the electromagnetic boundary condition. In this study we have identified the appropriate solution for the Fresnel reflection/refraction coefficients in light scattering calculation based on the ray tracing technique. We present the 3 x 2 refraction or transmission matrix that completely accounts for the inhomogeneity of the refracted wave in an absorbing medium. Using the Fresnel coefficients for an absorbing medium, we derive an asymptotic solution in an analytical format for the scattering properties of a general polyhedral particle. Numerical results are presented for hexagonal plates and columns with both preferred and random orientations. The asymptotic theory can produce reasonable accuracy in the phase function calculations in the infrared window region (wavelengths near 10 micron) if the particle size (in diameter) is on the order of 40 micron or larger. However, since strong absorption is assumed in the computation of the single-scattering albedo in the asymptotic theory, the single scattering albedo does not change with variation of the particle size. As a result, the asymptotic theory can lead to substantial errors in the computation of single-scattering albedo for small and moderate particle sizes. However, from comparison of the asymptotic results with the FDTD solution, it is expected that a convergence between the FDTD results and the asymptotic theory results can be reached when the particle size approaches 200 micron. We show that the phase function at side-scattering and backscattering angles is insensitive to particle shape if the random orientation condition is assumed. However, if preferred orientations are assumed for particles, the phase function has a strong dependence on scattering azimuthal angle. The single-scattering albedo also shows very strong dependence on the inclination angle of incident radiation with respect to the rotating axis for the preferred particle orientations.

Yang, Ping↗
NASA NTRS2001

Transonic Drag Prediction Using an Unstructured Multigrid Solver

This paper summarizes the results obtained with the NSU-3D unstructured multigrid solver for the AIAA Drag Prediction Workshop held in Anaheim, CA, June 2001. The test case for the workshop consists of a wing-body configuration at transonic flow conditions. Flow analyses for a complete test matrix of lift coefficient values and Mach numbers at a constant Reynolds number are performed, thus producing a set of drag polars and drag rise curves which are compared with experimental data. Results were obtained independently by both authors using an identical baseline grid and different refined grids. Most cases were run in parallel on commodity cluster-type machines while the largest cases were run on an SGI Origin machine using 128 processors. The objective of this paper is to study the accuracy of the subject unstructured grid solver for predicting drag in the transonic cruise regime, to assess the efficiency of the method in terms of convergence, cpu time, and memory, and to determine the effects of grid resolution on this predictive ability and its computational efficiency. A good predictive ability is demonstrated over a wide range of conditions, although accuracy was found to degrade for cases at higher Mach numbers and lift values where increasing amounts of flow separation occur. The ability to rapidly compute large numbers of cases at varying flow conditions using an unstructured solver on inexpensive clusters of commodity computers is also demonstrated.

Mavriplis, D. J.↗