SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Visible He/Ne laser beam substituted for invisible CO2 beam during alinement. System accomplished visually by using low-power He/Ne laser previously adjusted to visible beam parallel to invisible infrared CO2 laser beam. Method used to aline adjacent telescopes in other optical systems.
Explore the source record for details and available documents.
With the advent of stable, cw infrared lasers with moderate output power capabilities in the mid 1960's came the idea of using heterodyne detection, a mature radio frequency technique, in the infrared. This technique was first applied in radar and communications applications; however, it became apparent that infrared lasers and heterodyne detection techniques would be useful in a number of atmospheric measurement applications. The level to which these techniques are being put to use in field measurements is shown using two developed flight instruments as examples.
An in situ diffuse reflectance-Fourier transform infrared technique was developed to determine infrared spectra of graphite fiber prepregs as they were being cured. A bismaleimide, an epoxy, and addition polyimide matrix resin prepregs were studied. An experimental polyimide adhesive was also examined. Samples were positioned on a small heater at the focal point of diffuse reflectance optics and programmed at 15 F/min while FTIR spectra were being scanned, averaged, and stored. An analysis of the resulting spectra provided basic insights into changes in matrix resin molecular structure which accompanied reactions such as imidization and crosslinking. An endo-exothermal isomerization involving reactive end-caps was confirmed for the addition polyimide prepregs. The results of this study contribute to a fundamental understanding of the processing of composites and adhesives. Such understanding will promote the development of more efficient cure cycles.
Radiometric sensors for aviation hazards have the potential for widespread and inexpensive deployment on aircraft. This report contains discussions of three aviation hazards - icing, turbulence, and volcanic ash - as well as candidate radiometric detection techniques for each hazard. Dual-polarization microwave radiometry is the only viable radiometric technique for detection of icing conditions, but more research will be required to assess its usefulness to the aviation community. Passive infrared techniques are being developed for detection of turbulence and volcanic ash by researchers in this country and also in Australia. Further investigation of the infrared airborne radiometric hazard detection approaches will also be required in order to develop reliable detection/discrimination techniques. This report includes a description of a commercial hyperspectral imager for investigating the infrared detection techniques for turbulence and volcanic ash.
In our proposal we laid out work in three areas of relevance to atmospheric science: millimeter and submillimeter spectroscopy, variable temperature pressure broadening, and band and intensity measurements in the FIR. Below we will briefly discuss our progress during the second year of this project. In our millimeter and submillimeter (mm/submm) spectroscopic work, one of our goals has been to work towards the unification of the rotational (primarily obtained by mm/submm techniques) and rotational-vibrational (primarily obtained by infrared techniques) data sets in the context of theoretically well founded models which take advantage of the strengths of the data from each experimental technique. From the point of view of the development of the optimal data base for atmospheric observations, this is clearly a desirable goal. During the first year of this project we did an analysis of a weighted, mixed infrared and mm/submm data set of the n = 0, 1, and 2 torsional states of the ground vibrational state of HOOH. The purpose of this work is to provide a unified understanding of the spectrum, which is applicable in both the rotational and rotational - vibrational regimes. We have succeed in doing this in the context of a single weighted fit which accounts for both data sets to their respective experimental uncertainty (-0.1 and 10 MHz, respectively). Additionally, we have now done a similar analysis on the n = 0 torsional state of v(sub 3) and begun a similar analysis on v(sub 6). For several years we have been working on the mm/submm rotational spectra of the many excited vibrational states of HNO3, again with particular emphasis on the relationships between the mm/submm and infrared spectra. During the first year of this project we were able to use mm/submm spectroscopy to fully resolve the torsional splittings in 2 v(sub 9) and v(sub 5), establish a theoretically well founded quantitative relation between them, and show that both have their physical origin in the torsional motion of the v(sub 9) mode.This result has now been incorporated in a recent reanalysis of the infrared spectrum and has resulted in improved fits - eliminating what was in retrospect a systematic error associated with this previously unknown effect.
An experimental simulation of an in-flight wingtip vortical flow visualization technique uses infrared imaging to observe strong and concentrated vortices. This experiment is phase 1 of a two-phase infrared evaluation program. The system includes a vortex generator (model 320 Vortec Vortex Tube) which generates the required vortex. The mouth of the unit is mounted close to the free end of a half-inch diameter, sixteen and a half foot long stainless steel tubing (sized after tubing currently installed in the wings of an experimental Beechcraft Sundowner 180 aircraft). Dichloro difluoromethane (Freon-12) is entrained into the generated vortex. A breakdown of the vortices is indicated by the rapid diffusion and the resulting pattern is tracked using the infrared imager and video systems. Flow rates (volume and mass) are estimated at the laboratory and proposed flight conditions. The nominal flight altitude is expected to be 2500 feet.
Applications of passive visible and infrared techniques to the study of meteorological parameters are presented. For the remote sensing of temperature and humidity profiles, infrared sounder improvements have proceeded with the narrow band-pass channels approach, and the partially scanned interferogram approach. Current and planned infrared and microwave sea-surface temperature sounders have an expected accuracy of approximately 2 K, and this can be improved by using three super window channels from the 3.7 micron window region, with narrow band passes away from principal water vapor absorption lines. Cloud data remote sensing is currently performed from satellites, and these visible and infrared images have been used to track weather patterns. In addition, a passive infrared correlation-spectroscopy technique has been proposed for wind measurements. Finally, these techniques have also been applied to monitor such parameters as the Solar Constant, aerosols, and minor gas constituents.
The techniques considered make it possible to construct high performance low-pass wide-band, and medium-band filters at wavelengths in the range from 25 to 300 micrometers. Short wavelength rejection without appreciable loss at long wavelengths is achieved by means of small particle scattering. Spectral definition in the far infrared is obtained by cooling one or more crystalline materials to liquid-He or liquid-nitrogen temperatures. The problem of reflection losses at the various surfaces is solved by a new antireflection coating technique.
The principal subjects of investigation were the determination of the CO2 photodissociation quantum yields at the wavelengths from 1200 A to 1500 A, and the efficiency of electronic-to-vibrational energy transfer in the systems 0(1D) + CO, N2, CO2 yields 0(3P) + CO N2, CO2 vibrational energies. Measurements on the photodissociation quantum yield of CO2 in the 1200-1500 A region show that it is wavelength dependent, and for the six atomic line sources used, the quantum yield varied from 0.2 to 0.8. The data appear to fit the interpretation of stable CO2 bound states mixed with repulsive or predissociating states, since the low quantum yields coincide with the maximum structure in the CO2 absorption spectrum. The first reliable measurements were made on the efficiency of electronic-to-vibrational energy transfer in the systems 0(1D)-CO and 0(1D)-N2, using a uv resonance fluorescence technique. The 0(1D)-CO2 interaction was investigated by infrared techniques.
Bulk metal foil and thin film resistors occasionally contain localized defects within the etched resistor pattern. Common defects of this type include in-line constrictions referred to as notches, unremoved resistor material bridges between adjacent pattern lines, and embedded non-conductive particles in the resistor material. Such defects are prone to fracture due to thermomechanical fatigue during powered operation, especially power cycling, resulting in positive resistance change and open circuit failure modes. Common screening methods of optical microscopy, short time overload power tests (e.g., 6.25x rated power for 5 seconds) and burn-in (e.g., 1.5x rated power for 100 hours) are useful, but they are not always effective at removing devices with such defects. An improved method has been developed to screen for localized resistor pattern defects. The method involves the application of brief, high power electrical pulses at a low duty cycle while inspecting the resistor with a high resolution, high speed infrared camera. The following test conditions were found to be suitable for this purpose: 6.25x rated power, 1 to 5 pulses, 50 ms pulse width and 10% duty cycle. During the power pulsing, localized constrictions in the resistor pattern are identifiable as hot spots via the infrared camera. Reject criteria can be established based on observations of hot spots. To assess its effectiveness, a total of two hundred eighty (280) surface mount foil resistors (40 each from 7 different lots) were screened using this infrared technique. The screening identified twenty-nine (29) resistors with significant hot spots in the resistor pattern. All 280 resistors were then subjected to an industry standard 10,000 hour life test at 1x rated power at 70°C with power cycled for 90 minutes on and 30 minutes off. During life testing, three resistors exhibited positive resistance change failure mode. All three failures were due to thermomechanical fatigue failure of localized bridge defects at the locations identified via infrared screening. The results of this evaluation illustrate the benefits of the pulsed-power infrared detection screening technique to identify reliability suspect foil or thin film resistors that may escape common screening methods.
Bulk metal foil and thin film resistors occasionally contain localized defects within the etched resistor pattern. Common defects of this type include in-line constrictions referred to as notches, unremoved resistor material bridges between adjacent pattern lines, and embedded non-conductive particles in the resistor material. Such defects are prone to fracture due to thermomechanical fatigue during powered operation, especially power cycling, resulting in positive resistance change and open circuit failure modes. Common screening methods of optical microscopy, short time overload power tests (e.g., 6.25x rated power for 5 seconds) and burn-in (e.g., 1.5x rated power for 100 hours) are useful, but they are not always effective at removing devices with such defects. An improved method has been developed to screen for localized resistor pattern defects. The method involves the application of brief, high power electrical pulses at a low duty cycle while inspecting the resistor with a high resolution, high speed infrared camera. The following test conditions were found to be suitable for this purpose: 6.25x rated power, 1 to 5 pulses, 50 ms pulse width and 10% duty cycle. During the power pulsing, localized constrictions in the resistor pattern are identifiable as hot spots via the infrared camera. Reject criteria can be established based on observations of hot spots. To assess its effectiveness, a total of two hundred eighty (280) surface mount foil resistors (40 each from 7 different lots) were screened using this infrared technique. The screening identified twenty-nine (29) resistors with significant hot spots in the resistor pattern. All 280 resistors were then subjected to an industry standard 10,000 hour life test at 1x rated power at 70°C with power cycled for 90 minutes on and 30 minutes off. During life testing, three resistors exhibited positive resistance change failure mode. All three failures were due to thermomechanical fatigue failure of localized bridge defects at the locations identified via infrared screening. The results of this evaluation illustrate the benefits of the pulsed-power infrared detection screening technique to identify reliability suspect foil or thin film resistors that may escape common screening methods.
The use of visible and infrared techniques for estimating precipitation for flash flood, hydrological, and agricultural applications is discussed. Satellite derived rainfall estimates supplement other data or are the only data available. The Scofield/Oliver convective rainfall technique is used for analyzing a half hour period of heavy rainfall during a Chicago flash flood event. The results of a real time hydrological application of the Scofield/Oliver technique for the Hurricane Allen event are also presented. Visible and IR techniques for agricultural applications are also discussed.
One of the critical challenges for large area cadmium zinc telluride (CdZnTe) detector arrays is obtaining material capable of uniform imaging and spectroscopic response. Two complementary nondestructive techniques for characterizing bulk CdZnTe have been developed to identify material with a uniform response. The first technique, infrared transmission imaging, allows for rapid visualization of bulk defects. The second technique, x-ray spectral mapping, provides a map of the material spectroscopic response when it is configured as a planar detector. The two techniques have been used to develop a correlation between bulk defect type and detector performance. The correlation allows for the use of infrared imaging to rapidly develop wafer mining maps. The mining of material free of detrimental defects has the potential to dramatically increase the yield and quality of large area CdZnTe detector arrays.
The remote sensing of rain amounts is of great interest for a great variety of operational applications, including hydrology, hydroelectricity and agriculture is discussed. The microwave radiometer represents the most obvious technique, however, poor spatial and temporal resolution, together with the problems associated with the estimation of effective rain layer height make visible and IR techniques more promising at the present time. Based on bivariate frequency distribution of brightness versus temperature, brightness enhancing or infrared technique alone may be inadequate to deduce details of convective activity. It is implied that better estimates of rainfall will come from visible and IR observations combined than from either used alone. The technique identifies clouds with high probability of rain as those which have large optical and presumably physical thickness as measured by the visible albedo in comparison with their height, determined by the intensity of the IR emission.
Traditional down-looking infrared techniques for the detection and study of clouds have difficulties when clouds are within approximately 200 mbar of the surface. This is because of the lack of thermal contrast between the surface and a low cloud. We present a technique that, using a prior knowledge of the total water column, allows a down-looking high spectral resolution infrared spectrometer to recognize when a significant fraction of its field-of-view contains optically thick clouds (low-altitute or not).
This paper reviews remote sensing of snow and ice, techniques for improved monitoring, and incorporation of the new data into forecasting and management systems. The snowcover interpretation of visible and infrared data from satellites, automated digital methods, radiative transfer modeling to calculate the solar reflectance of snow, and models using snowcover input data and elevation zones for calculating snowmelt are discussed. The use of visible and near infrared techniques for inferring snow properties, microwave monitoring of snowpack characteristics, use of Landsat images for collecting glacier data, monitoring of river ice with visible imagery from NOAA satellites, use of sequential imagery for tracking ice flow movement, and microwave studies of sea ice are described. Applications of snow and ice research to commercial use are examined, and it is concluded that a major problem to be solved is characterization of snow and ice in nature, since assigning of the correct properties to a real system to be modeled has been difficult.
Using ultraviolet and infrared techniques, researchers investigated the origins of the tiny (approx. 10A) grains whose presence in the interstellar medium (ISM) is inferred from near-infrared photometry (Sellgren, Werner, and Dinerstein 1983; Sellgren 1984). The authors consider two possibilities: (1) that the grains are formed by condensation in stellar atmospheres; or (2) that they are formed by fragmentation of larger grains in interstellar shocks. They searched for evidence of very small grains in circumstellar environments by analyzing ultraviolet extinction curves in binaries containing hot companions, and by searching for the 3.3-micron emission feature in similar systems. The ultraviolet extinction curve analysis could be applied only to oxygen-rich systems, where small carbonaceous grains would not be expected, so these results provide only indirect information. Researchers find a deficiency of grains smaller than 800A in oxygen-rich systems, consistent with theoretical models of grain condensation which suggest that grains grow to large sizes before injection into the interstellar medium. More direct information on carbonaceous micrograins was obtained from the search for the 3.3-micron feature in carbon-rich binaries with hot companions, whose ultraviolet flux should excite the tiny grains to emit in the infrared. No 3.3-micron feature was found, suggesting that the micrograins are absent in these systems. In addition to the negative search for micrograins in circumstellar environments, researchers have also studied the possible association of these grains with shocks in the diffuse interstellar medium. Using Infrared Astronomy Satellite (IRAS) colors as indicators of the presence or absence of the small grains (e.g., Ryter, Puget, and Perault 1987 and references cited therein), researchers systematically searched for them in regions (reflection nebulae) expected to have sufficient ultraviolet flux to make them glow in the infrared. They found that the distribution is not uniform. The researchers propose that production of micrograins by fragmentation of larger grains in shocks could explain this uneven distribution.