Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Indirect drive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Self-generated magnetic fields in the hot spot of direct-drive cryogenic implosions at Omega

This work reports that Biermann self-generated magnetic fields of ≈200 MG and Hall parameters of ≈1.5 are produced in the stagnation phase of direct-drive cryogenic implosions at Omega. The magnetic fields produce a drop of 2.4% in fusion yield and 1% in ion temperature. A quantitative estimate of the effect of self-generated magnetic fields on yield and ion temperature is essential, since direct measurements of these fields are not available. Reconstructed simulations of the 50 Gbar implosions, with all the stagnation measurements reproduced simultaneously by a combination of mid- and low-mode asymmetries as degradation mechanisms [Bose et al., Phys. Plasmas 25, 062701 (2018)], are used to obtain the estimates. The magnetic fields cause a decrease in yield due to the Righi–Leduc heat flow, which exceeds any benefits from heat flow suppression due to magnetization. It is important to note that both direct-drive Omega-scale implosions and indirect-drive National Ignition Facility (NIF)-scale implosions [Walsh et al., Phys. Rev. Lett. 118, 155001 (2017)] produce similar estimates for the magnetic field strength, and both show a decrease in fusion yield, with the Righi–Leduc transport as the loss mechanism. However, the yield degradation at Omega is small and lower by ≈5× compared to the indirect-drive ignition-scale NIF estimate.

Physics↗
DOE OSTI2022

Evaluation of 3D Simulation Capabilities within xRAGE using a Suite of Test Problems

This presentation describes a 3D verification and validation suite for xRAGE. Three verification test problems for hydrodynamics are presented: the Kidder ball problem, the Verney shell problem, and a 5-material compression problem. There is excellent agreement between 2D and 3D XRAGE simulation results for these problems, and between the xRAGE results and the benchmark solutions. In addition, two 3D ICF test problems are presented, based on an OMEGA direct drive capsule experiment, and on a NIF indirect drive capsule experiment. These two ICF test problems are used to evaluate two hydrodynamic methods within xRAGE. In addition to hydrodynamics the simulations also include three temperature plasma physics, thermal conduction and radiation diffusion. When simulating either capsule in 3D the newer unsplit hydrodynamic method in xRAGE produces more vorticity relative to the older default method. For the indirect drive capsule the 3D simulations are in reasonable agreement with the experimental values of ion temperature and neutron production. Unstable 3D vortex rings are present near the DT ice/carbon interface which enhance the confinement of the DT ice.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Integrated Design of a Robust System for Inertial Fusion Energy

For inertial fusion energy (IFE) to be successful, designs need to work robustly including both target physics and engineering considerations. For a power plant to be reliable and have a high operating capacity factor, the integrated design of the target, driver, target fabrication, target injection system, and chamber all need to work together in way that is robust and repeatable to expected variations. One of the lesson’s learned from our experience at NIF is that designs that are sensitive have not performed as expected – even in single shot mode. The lesson’s learned from NIF should be folded into creating integrated designs for IFE and for evaluating the tradeoffs between the different parts of the IFE system. To do so, we propose using the NIF 1.3 MJ yield shot/design (N210808) as a starting point of a study of the feasibility of indirect drive designs for IFE. If the hohlraum inefficiency precludes indirect drive, the study would include direct drive or fast ignition versions of this design.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Optimization of Backscatter and Symmetry for Laser Fusion Experiments Using Multiple Tunable Wavelengths

A new additional wavelength-tuning capability has been implemented on the National Ignition Facility (NIF) laser allowing for unprecedented control of crossed-beam energy transfer (CBET) between all groups of beams for better performance of indirect-drive inertial confinement fusion (ICF) ignition experiments. In particular, this advance allows for negation and reversal of flow-induced CBET and the rebalancing of the intensity of different groups of beams within an indirect-drive (ICF) hohlraum. The experiments conducted at the NIF using a 1.1 MJ laser pulse with peak power of 390 TW demonstrate this high level of control through measurements of the precise changes to stimulated Brillouin scattering, typically driven by flow-induced CBET at the end of the pulse. Additionally, this new capability is shown to be able to predictably control gold-wall plasma expansion in the target driven by early-time flow-induced CBET. Estimates of early-time CBET from the wall expansion are shown to be consistent with simulation expectations. This new additional capability to control symmetry and backscatter expands the design space of current experiments and provides extra margin for increased laser energy in near-future experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

First large capsule implosions in a frustum-shaped hohlraum

Here, we report on the first indirect-drive implosions driven by a dual conical frustum-shaped hohlraum denoted “frustraum” and the experimental tuning campaigns leading up to two layered implosions. The campaign used 1.2 and 1.4 mm inner radius high density carbon (HDC) capsules and represented the largest HDC capsules to be imploded on the National Ignition Facility via indirect drive. Several techniques were successfully implemented to control the Legendre mode 2 capsule symmetry of the implosions, including changing the wall angle of the frustraum, which is not possible with cylindrical hohlraums. A mode 4 feature was observed and its implications for hotspot mix discussed. Two layered implosions were conducted with 1.2 mm inner radius capsules, the latter of which achieved the highest layered capsule absorbed energy on the National Ignition Facility using only 1.74 MJ of laser energy. The layered implosion results, along with generalized Lawson parameters, suggest that increasing the energy absorbed by the capsule at the expense of long coast times makes it more challenging to achieve ignition and that further reducing coast time (time between end of laser pulse and bang time) closer to the 1 ns level is warranted to improve the areal density and make it easier to achieve the hotspot temperature, alpha heating, and yield amplification required for ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Functional Photoresists for Energy Applications. Final Report

Monolithic ultralow-density porous bulk materials have recently attracted much interest due to many emerging applications in the areas of catalysis, energy storage and conversion, and thermal insulation. They are also important components of high energy density (HED) and inertial confinement fusion (ICF) targets. However, despite tremendous progress that has been made in the synthesis of porous materials, deterministic and independent control over microscopic architecture, density and composition remain key issues, and their integration in high precision devices requires cost and time-intensive mechanical machining that not only reduces reproducibility by generating debris but also limits the complexity of the 3D shapes that can be realized. In this project, we overcame these limitations by developing a universal templating capability that provides deterministic and independent control over density, composition, architecture, and macroscopic sample shape. This was achieved by developing the technology to 1) 3D print ultrahigh resolution, ultra-high precision polymeric micro-lattice templates, 2) coat these templates with the desired materials, and 3) removing the template (Fig. 1a). Atomic layer deposition (ALD) provides the atomic scale coating thickness accuracy required for precisely controlling density. While this templating approach had been demonstrated in prior work, limitations in suitable photoresists, 3D print technologies, print design, and template removal techniques did not allow the fabrication of millimeter-sized high-precision parts with sub-micron resolution. To enable this technology, we developed 1) two-photon polymerization (TPP) print designs that enable the fabrication of millimeter-sized, mechanically robust polymeric templates with sub-micron resolution and 2) a continuum level TPP printing simulation capability for additional print design guidance; 3) atomistic models to study photoresist polymerization kinetics and network topography, 4) refractive index matched polymeric and preceramic TPP photoresists, and 5) functional TPP photoresists including porous voxel structures and self-immolative polymer photoresist chemistries; and 6) damage free template removal techniques that enable the fabrication of defect-free high-precision low-density foam components. We also developed a templating approach for pure carbon microlattices with a unique tube-in-tube ligament morphology. As a test platform, we pursued the fabrication of foam liners that promise to further increase the neutron yield in indirect drive ICF experiments by improving implosion symmetry control and coupling between the laser and the deuterium-tritium fuel. This application requires fabrication and integration of a ultra-high precision, millimeter-sized, thin-walled (200-400 micrometer thick), low-density (10-30 mg/cc), high atomic number (high Z) cylindrical foam tube into the gold hohlraum of an indirect drive ICF target (Fig. 1b). While our hohlraum liner test case will mainly find application in HED and ICF experiments, the underlying science will also directly apply to previously developed nanoparticle and additive manufacturing technologies and will advance those techniques as well.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Achievement of Target Gain Larger than Unity in an Inertial Fusion Experiment

On December 5, 2022, an indirect drive fusion implosion on the National Ignition Facility (NIF) achieved a target gain G target of 1.5. This is the first laboratory demonstration of exceeding “scientific breakeven” (or G target > 1 ) where 2.05 MJ of 351 nm laser light produced 3.1 MJ of total fusion yield, a result which significantly exceeds the Lawson criterion for fusion ignition as reported in a previous NIF implosion [H. Abu-Shawareb (Indirect Drive ICF Collaboration), ]. This achievement is the culmination of more than five decades of research and gives proof that laboratory fusion, based on fundamental physics principles, is possible. This Letter reports on the target, laser, design, and experimental advancements that led to this result. Published by the American Physical Society 2024

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

FY20 LLNL Experimental Programs at Omega

In Fiscal Year 2020 (FY20), Lawrence Livermore National Laboratory’s (LLNL’s) High-Energy-Density Physics (HED) and Indirect Drive Inertial Confinement Fusion (ICF-ID) programs conducted numerous campaigns on the OMEGA and OMEGA-EP (EP) laser systems. This was the 22ndyear of National Lab collaborative experiments at OMEGA since the Nova Laser at LLNL shut down in 1999, building upon prior collaborations. In FY20overall,these LLNL programs led 375target shots, with 166shots using just the OMEGA laser system and209 shots using just the EP laser system. Approximately 34% of the total number of shots (35OMEGA shots and 93EP shots) supported the Indirect Drive Inertial Confinement Fusion Campaign. The remaining 66% (131OMEGA-only shots and 116EP-only shots) were dedicated to experiments for High-Energy-Density Physics.Highlights of the various HED and ICF-ID campaigns are summarized in the following reports.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Pathways towards break even for low convergence ratio direct-drive inertial confinement fusion

Following indirect-drive experiments which demonstrated promising performance for low convergence ratios (below 17), previous direct-drive simulations identified a fusion-relevant regime which is expected to be robust to hydrodynamic instability growth. This paper expands these results with simulated implosions at lower energies of 100 and 270 kJ, and ‘hydrodynamic equivalent’ capsules which demonstrate comparable convergence ratio, implosion velocity and in-flight aspect ratio without the need for cryogenic cooling, which would allow the assumptions of one-dimensional-like performance to be tested on current facilities. A range of techniques to improve performance within this regime are then investigated, including the use of two-colour and deep ultraviolet laser pulses. Finally, further simulations demonstrate that the deposition of electron energy into the hotspot of a low convergence ratio implosion through auxiliary heating also leads to significant increases in yield. Results include break even for 1.1 MJ of total energy input (including an estimated 370 kJ of short-pulse laser energy to produce electron beams for the auxiliary heating), but are found to be highly dependent upon the efficiency with which electron beams can be created and transported to the hotspot to drive the heating mechanism.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1990

Modelling of piezoelectric actuator dynamics for active structural control

The paper models the effects of dynamic coupling between a structure and an electrical network through the piezoelectric effect. The coupled equations of motion of an arbitrary elastic structure with piezoelectric elements and passive electronics are derived. State space models are developed for three important cases: direct voltage driven electrodes, direct charge driven electrodes, and an indirect drive case where the piezoelectric electrodes are connected to an arbitrary electrical circuit with embedded voltage and current sources. The equations are applied to the case of a cantilevered beam with surface mounted piezoceramics and indirect voltage and current drive. The theoretical derivations are validated experimentally on an actively controlled cantilevered beam test article with indirect voltage drive.

Hagood, Nesbitt W.↗
DOE OSTI2022

Compensating cylindrical Hohlraum mode 4 asymmetry via capsule thickness tailoring and effects on implosions

We report previously, hydrodynamic simulations suggested that precisely tailoring the capsule ablator thickness (shimming) could counterbalance cylindrical Hohlraum Legendre P 4 drive asymmetries at the capsule in laser indirect drive implosions. As a result, the stagnated deuterium–tritium (DT) fuel areal density P 4 asymmetry is reduced, potentially resulting in a nuclear yield increase. Inflight radiographs of various level of shimmed capsules with plastic (CH) ablators showed that shims can indeed control the in-flight capsule shell P 4 asymmetry, with a linear sensitivity to shim amplitude that is close to analytic estimates and simulations. Furthermore, the stagnated DT fuel areal density P 4 asymmetry inferred from downscattered neutron imaging was reduced when the capsule shim was applied, in agreement with simulations matching the inflight shell asymmetry. A nuclear yield improvement via shim was not observed, as predicted, likely due to implosion instabilities and as built capsule shim deviations from an ideal P 4 shape.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

A review on charged-particle transport modeling for laser direct-drive fusion

Inertial confinement fusion (ICF) with the laser-indirect-drive scheme has recently made a tremendous breakthrough recently after decades of intensive research effort. Taking this success to the next step, the ICF community is coming to a general consensus that laser direct-drive (LDD) fusion might be the viable way for enabling inertial fusion energy (IFE) and high-gain targets for other applications. Designing and understanding LDD fusion targets heavily rely on radiation-hydrodynamic code simulations, in which charged-particle transport plays an essential role in modeling laser-target energy coupling and bootstrap heating of fusion-produced α-particles. To better simulate charged-particle transport in LDD targets, over the past four decades the plasma physics community has advanced transport calculations from simple plasma physics models to sophisticated computations based on first-principles methods. In this review, we give an overview of the current status of charged-particle transport modeling for LDD fusion, including what challenges we still face and the possible paths moving forward to advance transport modeling for ICF simulations. We hope this review will provide a summary of exciting challenges to stimulate young minds to enter the field, facilitate further progress in understanding warm-dense matter physics, and ultimately bridge toward the success of reliable LDD fusion designs for IFE and other high-gain ICF applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Ablating Pellets for Areal Density Symmetry Control in Indirectly Driven Inertial Confinement Fusion Target Designs

Asymmetry of the compressed fusion fuel configuration, as characterized by a variation in areal density, in inertial confinement fusion (ICF) implosions is a known performance limitation. While ignition has been achieved on the National Ignition Facility (NIF), implosion symmetry was not perfect, and subsequent experiments that have extended fusion performance still struggle with symmetry control and would, in principle, perform much better if the areal density uniformity of the fuel was improved by eliminating thin regions in the DT (Deuterium-Tritium) fuel that develop by the time of peak compression. In indirect drive (IDD), altering the time-dependent laser cone fraction and cross-beam energy transfer are the usual tactics for controlling implosion asymmetry in IDD target designs, but it may be that those tools have been pushed to their limits. In this Letter, we present a new tactic for controlling the implosion using satellite ablating pellets to manipulate the time-dependent x-ray field around an ICF capsule. In theory and in simulations the action of these pellets is quite effective at reducing the swing of x-ray drive from waist hot to pole hot, thus achieving a more one-dimensional fuel configuration at peak compression. Simulations show that a factor of ∼2 in yield performance can be obtained via this technique, when applied to past record implosions on the NIF. As a result, some speculative alternate uses of the proposed target concept are also mentioned in the conclusion of this Letter.

Implosion symmetry↗
DOE OSTI2024

Experimental capabilities of the LMJ-PETAL facility

In this study, recent progress in the experimental capabilities of the LMJ-PETAL laser facility is reviewed. Updates on the indirect-drive D 2 implosion experiments and equation-of-state experiments using the LMJ laser are presented, including the commissioning of new plasma diagnostics. Several recent campaigns using the PETAL laser alone are also presented, namely the development of a platform using high-resolution and high-energy X-ray sources for radiography experiments, laser wakefield acceleration studies in the self-modulated regime, and neutron generation using a Target Normal Sheath Accelerated proton beam in a pitcher-catcher configuration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Lawson Criterion for Ignition Exceeded in an Inertial Fusion Experiment

For more than half a century, researchers around the world have been engaged in attempts to achieve fusion ignition as a proof of principle of various fusion concepts. Following the Lawson criterion, an ignited plasma is one where the fusion heating power is high enough to overcome all the physical processes that cool the fusion plasma, creating a positive thermodynamic feedback loop with rapidly increasing temperature. In inertially confined fusion, ignition is a state where the fusion plasma can begin “burn propagation” into surrounding cold fuel, enabling the possibility of high energy gain. While “scientific breakeven” (i.e., unity target gain) has not yet been achieved (here target gain is 0.72, 1.37 MJ of fusion for 1.92 MJ of laser energy), this work reports the first controlled fusion experiment, using laser indirect drive, on the National Ignition Facility to produce capsule gain (here 5.8) and reach ignition by nine different formulations of the Lawson criterion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Hotspot parameter scaling with velocity and yield for high-adiabat layered implosions at the National Ignition Facility

Here, in this paper, we present a study on hotspot parameters in indirect-drive, inertially confined fusion implosions as they proceed through the self-heating regime. The implosions with increasing nuclear yield reach the burning-plasma regime, hotspot ignition, and finally propagating burn and ignition. These implosions span a wide range of alpha heating from a yield amplification of 1.7–2.5. We show that the hotspot parameters are explicitly dependent on both yield and velocity and that by fitting to both of these quantities the hotspot parameters can be fit with a single power law in velocity. The yield scaling also enables the hotspot parameters extrapolation to higher yields. This is important as various degradation mechanisms can occur on a given implosion at fixed implosion velocity which can have a large impact on both yield and the hotspot parameters. The yield scaling also enables the experimental dependence of the hotspot parameters on yield amplification to be determined. The implosions reported have resulted in the highest yield (1.73×10 16 ±2.6%), yield amplification, pressure, and implosion velocity yet reported at the National Ignition Facility.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Approaching hydro-equivalent ignition in laser direct-drive via target design optimization using novel statistical modeling

Laser direct-drive offers significant advantages in terms of target simplicity, improved energy coupling, and large fuel masses over indirect drive. However, performance degradations from hydrodynamic and laser-plasma instabilities seeded and driven by the direct illumination pose limitations on the parameter space available for achieving ignition. In this paper, new design improvements are identified to forge a path forward for a hydro-equivalent ignition demonstration. The first is related to a new formulation of the statistical model (SM) used to accurately predict target performance directly from input parameters such as laser pulse shape and target specifications. This new SM formulation provides direct guidance on target dimensions and laser beam-to-target radius to achieve the highest fusion yield on the OMEGA laser. The second improvement comes from cooling the deuterium–tritium (DT) ice layer below the triple point right before shot time leading to lower DT vapor densities and higher convergence. Guided by these design improvements, a Bayesian optimization algorithm was used to design an implosion that is predicted to closely approach a Lawson triple product that hydrodynamically scales to ignition if equivalent laser–target coupling is achieved at laser energies typical of the National Ignition Facility.

Deuterium↗