Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Inconel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

An operando synchrotron study on the effect of wire melting state on solidification microstructures of Inconel 718 in wire-laser directed energy deposition

Directed energy deposition (DED) with a coaxial wire-laser configuration has gained significant attention in recent years for the production of large-scale metallic components because of its low directional dependence, fast deposition rate, high feedstock efficiency, and low manufacturing costs. This work studies the coaxial wire-laser DED process of Inconel 718 alloy under a stable deposition condition with a relatively low input volumetric energy density (55.5J/mm 3 ). Post characterization reveals a cluster of refined grains at the center-bottom region of the as-printed track. Operando high-energy synchrotron X-ray experiments and multi-physics modeling are applied innovatively to study the fundamental mechanism responsible for the formation of this microstructure. The X-ray diffraction experiment provides direct evidence, which is supported by the simulation, that the feeding wire can reach the melt pool bottom and release solid particles (primarily carbides) near the mushy zone owing to insufficient melting. Consequently, these sub-micron sized particles suppress the growth of large columnar grains and cause the formation of unique microstructural heterogeneity. In conclusion, this discovery offers new opportunities for tailoring the solidification microstructure by controlling the melting state of the feedstock wire in DED process, in addition to commonly known factors such as the thermal gradient and solidification velocity.

42 ENGINEERING↗
DOE OSTI2022

Development and performance of INCONEL® alloy 740H® seam-welded piping

INCONEL® alloy 740H® is an age-hardenable nickel-based alloy approved for pressure vessels and piping within ASME Section I, VIII, and B31.1. Currently, the code applies a weld strength reduction factor (WSRF) of 0.7 to the allowable stresses for longitudinal seam welds in the time dependent creep regime. In this work, a full-scale seam weld was successfully produced using typical industrial practices. The component was solution heat-treated and aged after fabrication to improve the performance of the weldment. Tensile, bend, impact, and low-cycle fatigue tests showed the component met all the specification requirements and elevated temperature properties were within base metal expectations with failures predominately in the weld metal. Long-term creep tests, including large samples more representative of the entire weldment, were fabricated and tested to times in excess of 10,000 h at multiple temperatures. Analysis of the creep data supports a WSRF of 0.9 for the solution annealed + aged weldments in contrast to the WSRF of 0.7 currently applied to welded + aged weldments. Metallurgical analysis shows that the solution annealing causes recrystallization of the weld metal and reduces the chemical compositional and microstructural gradients in the weldments resulting in acceptable short-term performance. In long-term creep, evidence for coarsened zones in the weldments due to discontinuous coarsening reactions were identified as the mechanism leading to accelerated creep damage formation in the weld metal and sample failure.

14 SOLAR ENERGY↗
DOE OSTI2026

Topology-driven compressive behavior of Inconel 718 lattice structures with Z-strut reinforcement fabricated by laser powder bed fusion

This study investigates the compressive deformation behavior and mechanical performance of Inconel 718 lattice structures fabricated by laser powder bed fusion (LPBF). Four unit-cell topologies—BCC, FCC, BCCZ, and FCCZ—were designed with a unit-cell size of 3 mm and fabricated under identical process conditions to isolate the effect of topology. Measured relative densities ranged from 14.65% to 17.72%. Compressive testing showed that Z-strut-reinforced topologies (BCCZ: 54.6 MPa; FCCZ: 80.2 MPa) exhibited higher strength than their unreinforced counterparts, which may be associated with mixed-mode deformation behavior enabled by the vertically aligned Z-struts. Finite element simulations and Digital Image Correlation (DIC) analysis support the observation of a transition from node-dominated deformation in BCC/FCC to mixed-mode deformation in BCCZ/FCCZ. These findings suggest that unit-cell topology is a key design variable for tailoring deformation mechanisms in LPBF lattice structures.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Effect of LPBF Processing Parameters on Inconel 718 Lattice Structures: Geometrical Characteristics, Surface Morphology, and Mechanical Properties

Laser Powder Bed Fusion (LPBF) enables the additive manufacturing of complex lattice structures. However, the fabrication of lattice structures via LPBF poses challenges in achieving the intended geometrical accuracy due to their inherent complexity. This study investigates the effects of LPBF processing parameters, specifically laser power and scanning speed, on the geometrical characteristics, surface quality, and mechanical behavior of Inconel 718 lattices structures. The results reveal that processing parameters required for the fabrication of near-full dense structures do not translate effectively to lattice configurations, as variations in energy input influence lattice geometry and surface quality. In this work, strut thickness, open-pore size, open-cell porosity, and surface roughness were measured, and the mechanical properties of the lattices were evaluated under shear loading. The findings indicate that lower energy inputs, achieved by reducing laser power and increasing scanning speed, yield porous structures but lead to mechanical degradation. In contrast, high energy inputs lead to lattices with enhanced strength but result in undesirable open-pore blockage and dimensional inaccuracies. These findings provide insights into tailoring LPBF parameters for dimensional accuracy in lattices and correlating the processing parameters to mechanical performance and surface roughness.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Plasticity and fracture behavior of Inconel 625 manufactured by laser powder bed fusion: Comparison between as-built and stress relieved conditions

In this work, the influence of stress relief on the plasticity and fracture behavior of Inconel 625 fabricated through laser powder bed fusion additive manufacturing (AM) was investigated. The as-built versus stress relieved microstructures were compared, showing similar grain structures but the presence of ~10 vol % δ phase in the stress relieved condition, and no δ phase in the as-built condition. Mechanical tests under plane strain tension were performed on the stress relieved samples, and an anisotropic plasticity model was calibrated and validated using finite element simulations. Uniaxial and notched tension tests were performed on both as-built and stress relieved samples to probe the effect of stress relief on stress state- and direction-dependent fracture behavior. It was found that on average, the fracture strain of the stress relieved samples along the build direction was 30% higher than that along the perpendicular build direction in the stress state range studied, and the stress relief heat treatment resulted in a 45% decrease in fracture strain. The fracture strain in stress relieved samples was more strongly dependent on stress state than in as-built samples.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Measurement of grain boundary strength of Inconel X-750 superalloy using in-situ micro-tensile testing techniques in FIB/SEM system

Grain boundaries (GBs), known as two-dimensional defects, are omnipresent in polycrystalline metallic alloys and thus influence a wide range of mechanical properties under different environmental conditions like irradiation and corrosion. Therefore, quantifying the strength of individual GBs is critical for understanding the degradation of mechanical properties of materials under different conditions. In this study we developed an efficient approach for the fabrication of micro-tensile specimens with a GB almost perpendicular to the tensile direction, which is expected to advance the development of individual GB tensile testing at micro or nanoscale in a wide scope of materials. Further, an in-situ cantilever micro-tensile testing method was developed and used to quantify the strength of a Σ3 GB in Inconel X-750 with the combination of finite element modeling. The average ultimate tensile strength (UTS) of a non-irradiated Σ3 GB is estimated at around 1.4 GPa, comparable to that of a neutron-irradiated Σ3 GB with a dose of ~1.5 dpa (1.3 GPa). Moreover, the in-situ push-to-pull micro-tensile testing technique developed in this work provides valuable insights into the high-angle GB deformation and fracture behavior. This method generates qualitatively similar ductility behavior before and after neutron irradiation as the bulk material testing. However, the ductility and UTS values obtained from this method are different from bulk measurements due to vastly different specimen dimensions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-Temperature RF Transmission Loss Characteristics of Platinum–Inconel 600 and Platinum–304 Steel Interconnects

Radio frequency (RF) transmission losses that occur at electronic interconnects is currently an important limitation of wireless sensors and other electronic device packages that must operate in high-temperature environments. Herein, in-situ RF transmission losses were measured for two types of interconnects: platinum (Pt) wire bonded to an Inconel 600 coaxial cable; and Pt-wire bonded to a block of 304 steel. Heating the Pt wire/Inconel interconnects at 800 °C for up to 200 hours were found to be very stable with no measurable transmission losses. In contrast, Pt wire/304 steel block interconnects examined over similar test periods at 800 °C exhibited gradual increases in transmission losses leveling off at 10, 38 and 85 mdB at 400 MHz, 700 MHz, and 1 GHz, respectively. Increasing the test temperature to 900 °C caused further elevated transmission losses of 30, 70 and 108 mdB at the same reported frequencies. By comparison, temperature cycling of the Pt wire/304 steel interconnects between room temperature and 900 °C was found to cause more significant degradation. In particular, four thermal cycles from room temperature to 900 °C resulted in losses of 75, 271, and 482 mdB at the same reported frequencies. Parabolic oxidation relative to the RF skin depth in the 304 steel block at the tested frequencies are discussed as possible reasons for the transmission losses during the isothermal soaks, whereas interconnect degradation due to differences in thermal expansion between Pt and 304 steel are primarily responsible for transmission losses caused by high temperature cycling.

304 steel↗
DOE OSTI2022

Diffusion bonded compact heat exchanger in Inconel 740H for high temperature and high-pressure applications

It is desired to develop heat exchangers able to be operated at high temperatures (750˚C) and pressures (3636 psi) for use in advanced Brayton power cycle. Conventional materials have not had the high strength at temperature required for these applications previously, however a fairly new material Inconel 740H developed by Special Metals for the ultra-supercritical water fossil industry has shown good performance under these conditions. In further efforts to capitalize on these new high strength high temperature alloys CompRex has developed a diffusion bonding procedure capable of alloying compact high effectiveness heat exchangers that can perform under these high temperature and high-pressure conditions. Initial tests of the heat exchanger are being conducted at the University of Wisconsin using supercritical CO2 working fluid. The bonding process has been adjusted such that the strength of the bonded block has achieved over 90% yield and tensile strength of the 740H base material values. Grain size before and after bonding were measured to determine the extent of grain growth and grain diffusion across the interface. A discussion of the heat exchanger design, etching and initial tensile tests on sample bonds will be discussed.

14 SOLAR ENERGY↗
DOE OSTI2020

3D Characterization of the Columnar-to-Equiaxed Transition in Additively Manufactured Inconel 718

Additive manufacturing (AM) provides enormous processing flexibility, enabling novel part geometries and optimized designs. Access to a local heat source further permits the potential for local microstructure control on the scale of individual melt pools, which can enable local control of part properties. In order to design tailored processing strategies for target microstructures, models predicting the columnar-to-equiaxed transition must be extended to the high solidification velocities and complex thermal histories present in AM. Here, we combine 3D characterization with advanced modeling techniques to develop a more complete understanding of the solidification process and evolution of microstructure during electron beam melting (EBM) of Inconel 718. Full calibration of existing microstructure prediction models demonstrates the differences between AM processes and more conventional welding techniques, underlying the need for accurate determination of key parameters that can only be measured directly in 3D. The ability to combine multisensor data in a consistent 3D framework via data fusion algorithms is essential to fully leverage these advanced characterization approaches. Thermal modeling provides insight on microstructure development within isolated solidification events and demonstrates the role of Marangoni effects on controlling solidification behavior.

Polonsky, Andrew↗
DOE OSTI2023

Tailoring the γ-γ'-γ" dual superlattice microstructure of INCONEL® 725 by high temperature aging and Nb/Ta additions for superior creep properties

Next-generation energy systems require superior resistance to creep deformation due to the considerably prolonged exposure times at operating stress and temperature. To improve the elevated temperature properties of INCONEL® 725 (IN725), a corrosion resistant alloy, several variants with different Ti/Al ratio and judicious amounts of Nb and Ta were made. Furthermore, a high temperature aging (HTA) heat treatment, designed to promote favorable precipitate phase formation, was explored. These adjustments allowed to tailor the amount and type of precipitate strengthening which led to significant increases in time to failure. The Ti/Al ratio was used to favor the formation of γ' or γ" precipitates. Compact morphology precipitates, consisting of γ' precipitates surrounded by a γ" shell, were formed in alloys with a low Ti/Al ratio. The HTA increased the creep life of various alloy formulations up to a maximum improvement of 371% as compared to the standard aging heat treatment. The Nb and Ta additions had a similar effect on increasing creep life by promoting and stabilizing γ" precipitation. The positive effect of the additions was even more pronounced when coupled with the HTA. A phase stability study with up to 10,000 h exposure at 700°C revealed that the compact morphology helped in slightly reducing coarsening of the γ' precipitates, although the effect on creep was not significant. The findings of this study enable design of dual superlattice alloys through microstructural engineering that yields superior performance and can be applied to a wide range of alloys in the IN718 and derivatives family.

Antonov, Stoichko↗
DOE OSTI2023

Factors Influencing Propensity for Stress Relaxation Cracking in Inconel® Alloy 740H® and Practical Guidance for Applications

Inconel® alloy 740H® (UNS N07740) was the first age-hardenable nickel-based alloy approved by the ASME Boiler & Pressure Vessel Code for use in pressure-boundary applications. In recent years, advanced energy systems such as supercritical CO2 power cycles have utilized alloy 740H in large demonstration projects driven by the requirement for higher fluid temperatures and pressures. Stress relaxation cracking (SRxC) following post-weld heat-treatment (PWHT), also known as strain age cracking (SAC), has been identified in a limited number of weldments during these industrial builds resulting in focused research to further clarify factors influencing this cracking tendency. This paper will summarize some of the findings from shop and field fabrication leading to successful welds and characteristics of observed SRxC. Laboratory experiments supported by microstructural characterization will be presented to highlight the importance of variables such as strain, material starting condition, and PWHT temperatures. Finally, the results will be summarized within the context of practical guidance for industry to successfully weld the material in boiler, heat exchanger, and piping applications.

14 SOLAR ENERGY↗
DOE OSTI2023

Relationship between Grain Size and Sample Thickness on the Creep-Rupture Performance of Thin Metallic Sheets of INCONEL Alloy 740H

A study was conducted on INCONEL® alloy 740H® to examine the role of grain size and sheet thickness on the alloy’s creep-rupture behavior. Three different starting sheet thicknesses were utilized and multiple heat-treatment conditions anticipated for compact heat exchanger (CHX) manufacturing were applied to produce a range of grain sizes. Creep-rupture testing was conducted at 750 °C for times up to about 6000 h and the results were compared to wrought databases. The data show that both creep strength and ductility were important factors in the overall creep performance of the sheets. Reductions in performance were observed due either to accelerated creep when grain size was fine or loss of rupture ductility when grain sizes approached the sheet thickness. Some combinations of heat-treatment and thickness were able to produce typical expected wrought creep properties. Historically a ‘rule-of-thumb’ requirement for creep testing suggests 3-5 grains per sample minimum dimension to ensure homogeneous behavior. This research shows that to ensure representative wrought creep performance (i.e. no effect of sample size), the sample minimum cross-section should be 10 times the average ASTM grain size. Statistical analysis of the microstructures suggests the population of larger grains as a controlling feature in creep failure.

14 SOLAR ENERGY↗
DOE OSTI2022

Microstructural Development in Inconel 718 Nickel-Based Superalloy Additively Manufactured by Laser Powder Bed Fusion

Excellent weldability and high temperature stability make Inconel 718 (IN718) one of the most popular alloys to be produced by additive manufacturing. Here in this study, we investigated the effects of laser powder bed fusion (LPBF) parameters on the microstructure and relative density of IN718. The samples were fabricated with independently varied laser power (125 - 350W), laser scan speed (200 - 2200 mm/s), and laser scan rotation (0° - 90°). Archimedes’ method, optical microscopy, and scanning electron microscopy were employed to assess the influence of LPBF parameters on the relative density and microstructure. Optimal processing windows were identified for a wide range of processing parameters and relative density greater than 99.5% was achieved using volumetric energy density between 50 and 100 J/mm3. Microstructural features including melt pool geometry, lack of fusion defect, keyhole porosity, and sub-grain cellular microstructure were examined and quantified to correlate to LPBF parameters. A simple empirical model was postulated to relate relative sample density and LPBF volumetric energy density. Melt pool dimensions were quantitatively measured and compared to estimations based on Rosenthal solution, which yielded a good agreement with the width, but underestimated the depth, particularly at high energy input, due to lack of consideration for keyhole mode. In addition, the sub-grain cellular-dendritic microstructure in the as-built samples was observed to decrease with increasing laser scan speed. Quantification of the sub-micron cellular-dendritic microstructure yielded estimated cooling rate in the order of 10 5 – 10 7 K/s.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Elucidating the effect of preheating temperature on melt pool morphology variation in Inconel 718 laser powder bed fusion via simulation and experiment

In laser powder bed fusion (L-PBF) additive manufacturing, the mechanical performance, microstructure and defects of fabricated parts are closely associated with the melt pool morphology, e.g., its dimension and shape through the building process. Past studies have largely focused on how the process parameters such as laser power and scan speed affect melt pool characteristics. In this study, the melt pool morphology variation as a function of preheating temperature in the conduction, transition, and keyhole regimes and the underlying mechanisms in each regime are investigated through ex-situ sample characterization and computation thermal fluid dynamics (CtFD) simulation. Single tracks with different combinations of laser power and scan speed are deposited on an Inconel 718 bare plate preheated to a temperature range of 100–500 °C in the experiment. Significant changes are observed in melt pool morphology as a function of preheating temperature from optical measurements of melt track cross sections. The depth of melt pool in the three regimes increases monotonically with preheating temperature, e.g., at 500 °C, the experimental melt pool depth is increased by 49% in conduction regime, 34% in transition regime and 33% in keyhole regime, respectively, while the variation of melt pool width in each regime does not all follow an increasing trend but depends on the melt pool regimes. Melt pool width variation in the conduction and transition regimes is found to depend on the enhanced heat conduction directly related to temperature dependent thermal properties. Through validated CtFD simulations, it is found that in the keyhole regime the evaporation mass, recoil pressure, and laser drilling effect is enhanced with higher preheating temperature, which gives rise to a deeper melt pool. The simulations also reveal that preheating temperature significantly elongates the melt track length due to the increased flow rate and strong recoil pressure that accelerates the backward flow.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Analysis of inconel 600 oxidized under loss-of-coolant accident conditions: A multi-modal approach

Understanding the performance of cladding materials during a loss-of-coolant accident scenario is crucial for developing next-generation accident tolerant nuclear fuel rod claddings. We describe a multi-modal approach combining synchrotron-based diffraction, and Raman spectroscopy with nano-scale electron microscopy techniques for investigating oxidation of Inconel 600 (A600) in steam and air environments at 1200 °C for 2 h. We report that A600 exposed to steam develops a Cr 2 O 3 -enriched surface layer while a mixed phase oxide layer containing NiFe 2 O 4 , Cr 2 O 3 , Fe 3 O 4 and Fe (3–x) CrxO 4 is formed in air. Mechanism of oxidation for A600 in air and steam environments is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of differently oriented interlayer phases on the radiation damage of Inconel-$\mathrm{Ni}$ multimetallic layered composite

Multimetallic layered composites (MMLCs) have shown an excellent potential for application under extreme environments, e.g., accident-tolerant fuel cladding, because of their low oxidation tendency and high corrosion resistance. Interfacial phases or complexions in nanocrystalline materials accelerate the annihilation of defects and enhance the radiation resistance of materials, making MMLCs with engineered interlayer phases compelling to deploy in extreme conditions. However, implementation of MMLCs in full capacity remained a challenge due to a lack of fundamental understanding of the underlying mechanisms governing the characteristics of the interface between the metallic layers. The precise role of interlayer phases in MMLCs and their interaction with defects, specifically under extreme conditions, is still unexplored. Pursuing atomistic simulations for various Inconel-Ni MMLCs model materials, we revealed accelerated defect mobility in interlayers with larger crystalline misorientation and the inverse relationship between the interface sink strength to the misorientation angle. Furthermore, we found a linear relation between interlayer misorientation angle with the density of radiation-induced defects and radiation enhanced displacements. So, our results indicate that radiation-induced material degradation is accelerated by the higher defect formation tendency of MMLCs with a high-angle interlayer interface.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Interfacial characteristics of P91 steel - Inconel 740H bimetallic structure fabricated using wire-arc additive manufacturing

Although bimetallic structures can offer unique solutions to engineering problems with varying functionality, joining two dissimilar alloys using additive manufacturing involves challenges such as cracking and segregation. In this work, bimetallic structures of Inconel 740H superalloy and P91 steel are processed using wire-arc additive manufacturing (WAAM) for the first time. P91 steel is directly deposited over 740H with a cooling time of 20 minutes in between the two depositions. During microstructure characterization, a large gradient zone with coarse grains spanning for ~2200 μm is observed. Moreover, the microhardness of the gradient zone is the least in comparison with the P91 and 740H deposits. No deleterious phase formation is found; however, intergranular cracks are observed along the gradient zone. In order to deduce the reason for cracking, non-equilibrium solidification simulations are performed for the mixed compositions of P91 and 740H in the gradient zone. Here, the reasons for crack formation in the gradient zone are the sudden change in the volumetric coefficient of thermal expansion due to the formation of MC carbides as well as the development of local strains from the thermal residual stresses. Therefore, altering the deposition sequence and introducing gradient layers with mixed composition between the P91 and 740H deposits will be beneficial in achieving defect-free builds. Through the integration of experiments and simulation, this work gains valuable insights into the processability of dissimilar alloy manufacturing using the WAAM technique.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2025

Effect of homogenization heat treatment on the evolution of carbonitrides in powder bed fusion processed INCONEL 718

Inconel 718 fabricated using laser powder-bed fusion, contains precipitates in the as-built condition that can be coarsened by high-temperature heat treatments. In this study, two homogenization heat treatment regimens were applied to discern the impact of heat treatment conditions on the growth of complex M(C, N) carbonitrides. In the first heat treatment, the samples underwent heat treatment between 1050 °C and 1200 °C for 0.5 h. In the second heat treatment, the samples were held at a constant temperature of 1150 °C, with varied holding times from 0.5 h to 8 h. Heat treatments dissolved the unstable Laves phase, but the carbonitrides persisted in the structure regardless of temperature and duration. Changes in the compositions, lattice parameters, and sizes of M(C, N) carbonitrides were measured using transmission electron microscopy and high-energy synchrotron X-ray diffraction. The results show an Nb enrichment at carbonitrides while Nb loss at the matrix with increased homogenization temperature. The findings suggest the optimum heat treatment conditions to achieve a homogeneous structure and controlled carbonitride size are between 1000 and 1050 °C for up to 2 h.

IN178↗