Results for “Impact Ice” — Page 3

NASA NTRS2018

Fragment Size Distribution for Ice Particle Impacts on a Glass Plate

This work presents the results of an experimental study of ice particle impacts on a flat glass plate. The experiment was conducted at the Ballistics Impact Laboratory of NASA Glenn Research Center. The main objective of the experiment was to gain understanding about the modifications needed to the experimental configuration for a future parametric study at a larger range of values for particle diameters and other parameters. This was achieved by studying the effect of the velocity of an impacting ice particle on the post-impact fragment size and distribution for a reduced range of impacting particle diameters. Pre-impact particle diameter and velocity data were captured with a high-speed side camera. Post-impact fragment data were captured in a single frame with a 29-megapixel camera located above and normal to the target. Repeat runs were conducted for ice particles with diameters ranging from 1.7 to 2.9 millimeters, impacting at velocities between 39 and 98 meters per second. The fragment areas were measured, and the corresponding equivalent diameters and histogram distributions were calculated. Analysis of the data showed that the average equivalent diameter for the fragments in a run was an order of magnitude smaller than the diameter of the impacting ice particle. The histograms for equivalent diameter distribution were nonnormal with long tails, with most of the fragments having equivalent diameters concentrated toward the minimum value of the fragment size that could be resolved. Factors affecting the accuracy of the data during the digital imaging analysis were identified. Needed modifications to the setup to handle small size ice particles and other testing conditions were also identified.

engine icing↗

NASA NTRS2015

Ice Particle Impacts on a Flat Plate

An experimental study was conducted at the Ballistic Laboratory of NASA Glenn Research Center to study the impact of ice particles on a stationary flat surface target set at 45 degrees with respect to the direction of motion of the impinging particle (Figure 1). The experiment is part of NASA efforts to study the physics involved in engine power-loss events due to ice-crystal ingestion and ice accretion formation inside engines. These events can occur when aircraft encounter high-altitude convective weather.

ice particle↗

NASA NTRS2006

Dynamic Crush Characterization of Ice

During the space shuttle return-to-flight preparations following the Columbia accident, finite element models were needed that could predict the threshold of critical damage to the orbiter's wing leading edge from ice debris impacts. Hence, an experimental program was initiated to provide crushing data from impacted ice for use in dynamic finite element material models. A high-speed drop tower was configured to capture force time histories of ice cylinders for impacts up to approximately 100 ft/s. At low velocity, the force-time history depended heavily on the internal crystalline structure of the ice. However, for velocities of 100 ft/s and above, the ice fractured on impact, behaved more like a fluid, and the subsequent force-time history curves were much less dependent on the internal crystalline structure.

Fasanella, Edwin L.↗

NASA NTRS2014

Ice Particle Impacts on a Moving Wedge

This work presents the results of an experimental study of ice particle impacts on a moving wedge. The experiment was conducted in the Adverse Environment Rotor Test Stand (AERTS) facility located at Penn State University. The wedge was placed at the tip of a rotating blade. Ice particles shot from a pressure gun intercepted the moving wedge and impacted it at a location along its circular path. The upward velocity of the ice particles varied from 7 to 12 meters per second. Wedge velocities were varied from 0 to 120 meters per second. Wedge angles tested were 0, 30, 45, and 60. High speed imaging combined with backlighting captured the impact allowing observation of the effect of velocity and wedge angle on the impact and the post-impact fragment behavior. It was found that the pressure gun and the rotating wedge could be synchronized to consistently obtain ice particle impacts on the target wedge. It was observed that the number of fragments increase with the normal component of the impact velocity. Particle fragments ejected immediately after impact showed velocities higher than the impact velocity. The results followed the major qualitative features observed by other researchers for hailstone impacts, even though the reduced scale size of the particles used in the present experiment as compared to hailstones was 4:1.

Impacts↗

NASA NTRS2004

Ice Particle Impact on Cloud Water Content Instrumentation

Determining the total amount of water contained in an icing cloud necessitates the measurement of both the liquid droplets and ice particles. One commonly accepted method for measuring cloud water content utilizes a hot wire sensing element, which is maintained at a constant temperature. In this approach, the cloud water content is equated with the power required to keep the sense element at a constant temperature. This method inherently assumes that impinging cloud particles remain on the sensing element surface long enough to be evaporated. In the case of ice particles, this assumption requires that the particles do not bounce off the surface after impact. Recent tests aimed at characterizing ice particle impact on a thermally heated wing section, have raised questions about the validity of this assumption. Ice particles were observed to bounce off the heated wing section a very high percentage of the time. This result could have implications for Total Water Content sensors which are designed to capture ice particles, and thus do not account for bouncing or breakup of ice particles. Based on these results, a test was conducted to investigate ice particle impact on the sensing elements of the following hot-wire cloud water content probes: (1) Nevzorov Total Water Content (TWC)/Liquid Water Content (LWC) probe, (2) Science Engineering Associates TWC probe, and (3) Particle Measuring Systems King probe. Close-up video imaging was used to study ice particle impact on the sensing element of each probe. The measured water content from each probe was also determined for each cloud condition. This paper will present results from this investigation and attempt to evaluate the significance of ice particle impact on hot-wire cloud water content measurements.

Emery, Edward F.↗

NASA NTRS2014

Ice Particle Impacts on a Moving Wedge

This work presents the results of an experimental study of ice particle impacts on a moving wedge. The experiment was conducted in the Adverse Environment Rotor Test Stand (AERTS) facility located at Penn State University. The wedge was placed at the tip of a rotating blade. Ice particles shot from a pressure gun intercepted the moving wedge and impacted it at a location along its circular path. The upward velocity of the ice particles varied from 7 to 12 meters per second. Wedge velocities were varied from 0 to 120 meters per second. Wedge angles tested were 0 deg, 30 deg, 45 deg, and 60 deg. High speed imaging combined with backlighting captured the impact allowing observation of the effect of velocity and wedge angle on the impact and the post-impact fragment behavior. It was found that the pressure gun and the rotating wedge could be synchronized to consistently obtain ice particle impacts on the target wedge. It was observed that the number of fragments increase with the normal component of the impact velocity. Particle fragments ejected immediately after impact showed velocities higher than the impact velocity. The results followed the major qualitative features observed by other researchers for hailstone impacts, even though the reduced scale size of the particles used in the present experiment as compared to hailstones was 4:1.

Roughness↗

NASA NTRS1947

Laboratory Investigation of Ice Formation and Elimination in the Induction System of a Large Twin-engine Cargo Aircraft

The icing characteristics, the de-icing rate with hot air, and the effect of impact ice on fuel metering and mixture distribution have been determined in a laboratory investigation of that part of the engine induction system consisting of a three-barrel injection-type carburetor and a supercharger housing with spinner-type fuel injection from an 18-cylinder radial engine used on a large twin-engine cargo airplane. The induction system remained ice-free at carburetor-air temperatures above 36 F regardless of the moisture content of the air. Between carburetor-air temperatures of 32 F and 36 F with humidity ratios in excess of saturation, serious throttling ice formed in the carburetor because of expansion cooling of the air; at carburetor-air temperatures below 32 F with humidity ratios in excess of saturation, serious impact-ice formations occurred, Spinner-type fuel injection at the entrance to the supercharger and heating of the supercharger-inlet elbow and the guide vanes by the warn oil in the rear engine housing are design features that proved effective in eliminating fuel-evaporation icing and minimized the formation of throttling ice below the carburetor. Air-flow recovery time with fixed throttle was rapidly reduced as the inlet -air wet -bulb temperature was increased to 55 F; further temperature increase produced negligible improvement in recovery time. Larger ice formations and lower icing temperatures increased the time required to restore proper air flow at a given wet-bulb temperature. Impact-ice formations on the entrance screen and the top of the carburetor reduced the over-all fuel-air ratio and increased the spread between the over-all ratio and the fuel-air ratio of the individual cylinders. The normal spread of fuel-air ratio was increased from 0.020 to 0.028 when the left quarter of the entrance screen was blocked in a manner simulating the blocking resulting from ice formations released from upstream duct walls during hot-air de-icing.

ICE PREVENTION - AIR HEATING↗

NASA NTRS2006

Forces Generated by High Velocity Impact of Ice on a Rigid Structure

Tests were conducted to measure the impact forces generated by cylindrical ice projectiles striking a relatively rigid target. Two types of ice projectiles were used, solid clear ice and lower density fabricated ice. Three forms of solid clear ice were tested: single crystal, poly-crystal, and "rejected" poly-crystal (poly-crystal ice in which defects were detected during inspection.) The solid ice had a density of approximately 56 lb/cu ft (0.9 gm/cu cm). A second set of test specimens, termed "low density ice" was manufactured by molding shaved ice into a cylindrical die to produce ice with a density of approximately 40 lb/cu ft (0.65 gm/cu cm). Both the static mechanical characteristics and the crystalline structure of the ice were found to have little effect on the observed transient response. The impact forces generated by low density ice projectiles, which had very low mechanical strength, were comparable to those of full density solid ice. This supports the hypothesis that at a velocity significantly greater than that required to produce fracture in the ice, the mechanical properties become relatively insignificant, and the impact forces are governed by the shape and mass of the projectile.

Pereira, J. Michael↗

NASA NTRS1997

Tests of the Performance of Coatings for Low Ice Adhesion

This paper reports studies of the performance of low-ice-adhesion coatings by NASA Lewis and BFGoodrich. Studies used impact ice accreted both in the NASA Lewis Icing Research Tunnel (IRT) and in the BFGoodrich Icing Wind Tunnel (IWT) and static ice in a BFGoodrich bench-top parallel-plate shear rig. Early tests at NASA Lewis involved simple qualitative evaluations of the ease of removing impact ice from a surface. Coated surfaces were compared with uncoated ones. Some of the coatings were tested again with static ice at BFGoodrich to obtain quantitative measurements. Later, methods to establish the adhesion force on surfaces subjected to impact ice were explored at Lewis. This paper describes the various test programs and the results of testing some of the coatings looked at over the past 5 years. None of the coatings were found to be truly ice-phobic; however, the most effective coatings were found to reduce the adhesion of ice to about 1/2 that of an uncoated aluminum sample.

Anderson, David N.↗

NASA NTRS1991

Influence of aerodynamic forces in ice shedding

Stresses in accreted ice on a typical airfoil impact ice caused by aerodynamic forces have been studied using finite element analyses. The objective of this study is to determine the significance of these stresses relative to values needed to cause ice shedding. In the case studied, stresses are not significant (less than 10 percent) when compared to the fracture value for airspeeds below a Mach number of 0.45. Above this velocity, the influence of aerodynamic forces on impact ice stresses should be considered in analyses of ice shedding.

Scavuzzo, R. J.↗

NASA NTRSDate not supplied

Regional Impacts of Ice Sheet Surface Representation Improvements in an Earth System Model

Ice sheet surface conditions and their subsequent impact on surface mass balance play an important role in ice sheet dynamics and ice sheet interaction with the overlying atmosphere and surrounding ocean. The NASA Global Modeling and Assimilation Office’s (GMAO) Goddard Earth Observing System (GEOS) ecosystem of models and reanalyses model ice sheet and glacier surface mass balance with a moderately complex snow and ice module, including prognostic surface albedo evolution, fractional snow cover, and snowpack hydrology and meltwater retention. With this configuration, Greenland near surface air temperatures and ice sheet melt are well represented in MERRA-2, GMAO’s current atmospheric reanalysis; however, the similarity to observations in some regions is due, in part, to compensating biases in surface energy budget. Recent improvements to GEOS’ cloud microphysics and longwave radiation parameterizations reduced biases in surface net longwave radiation and exacerbated surface net shortwave radiation biases, effectively increasing near surface temperatures and melting, particularly during the summer months. Here, we demonstrate the Earth system response to an improved representation of the ice sheet surface focused on minimizing the surface energy biases and increasing spatial and temporal representativeness. New changes to the surface albedo parameterization, including the introduction of a prognostic aerosol darkening scheme, help mitigate shortwave biases, while modifications to surface roughness characteristics improve near surface sensible heat fluxes. Focusing on the Arctic and Greenland, we examine the combined impact on these changes on regional weather conditions and ice sheet surface mass balance using a high resolution atmospheric only experiment, and we use a coupled model configuration to assess the impact on oceanic conditions and subseasonal-to-seasonal prediction. Overall, these improvements increase modeled ice sheet surface realism and provide a strong basis for more accurate ice sheet mass balance in GMAO’s future reanalyses and forecasting systems.

Lauren C Andrews↗

NASA NTRSDate not supplied

Regional Impacts of Ice Sheet Surface Representation Improvements in an Earth System Model

Ice sheet surface conditions and their subsequent impact on surface mass balance play an important role in ice sheet dynamics and ice sheet interaction with the overlying atmosphere and surrounding ocean. The NASA Global Modeling and Assimilation Office’s (GMAO) Goddard Earth Observing System (GEOS) ecosystem of models and reanalyses model ice sheet and glacier surface mass balance with a moderately complex snow and ice module, including prognostic surface albedo evolution, fractional snow cover, and snowpack hydrology and meltwater retention. With this configuration, Greenland near surface air temperatures and ice sheet melt are well represented in MERRA-2, GMAO’s current atmospheric reanalysis; however, the similarity to observations in some regions is due, in part, to compensating biases in surface energy budget. Recent improvements to GEOS’ cloud microphysics and longwave radiation parameterizations reduced biases in surface net longwave radiation and exacerbated surface net shortwave radiation biases, effectively increasing near surface temperatures and melting, particularly during the summer months. Here, we demonstrate the Earth system response to an improved representation of the ice sheet surface focused on minimizing the surface energy biases and increasing spatial and temporal representativeness. New changes to the surface albedo parameterization, including the introduction of a prognostic aerosol darkening scheme, help mitigate shortwave biases, while modifications to surface roughness characteristics improve near surface sensible heat fluxes. Focusing on the Arctic and Greenland, we examine the combined impact on these changes on regional weather conditions and ice sheet surface mass balance using a high resolution atmospheric only experiment, and we use a coupled model configuration to assess the impact on oceanic conditions and subseasonal-to-seasonal prediction. Overall, these improvements increase modeled ice sheet surface realism and provide a strong basis for more accurate ice sheet mass balance in GMAO’s future reanalyses and forecasting systems.

Lauren C. Andrews↗

NASA NTRS2014

Detection of the Impact of Ice Crystal Accretion in an Aircraft Engine Compression System During Dynamic Operation

The accretion of ice in the compression system of commercial gas turbine engines operating in high ice water content conditions is a safety issue being studied by the aviation community. While most of the research focuses on the underlying physics of ice accretion and the meteorological conditions in which accretion can occur, a systems-level perspective on the topic lends itself to potential near-term operational improvements. Here a detection algorithm is developed which has the capability to detect the impact of ice accretion in the Low Pressure Compressor of an aircraft engine during steady flight as well as during changes in altitude. Unfortunately, the algorithm as implemented was not able to distinguish throttle changes from ice accretion and thus more work remains to be done.

high ice water content↗

NASA NTRS2014

Detection of the Impact of Ice Crystal Accretion in an Aircraft Engine Compression System During Dynamic Operation

The accretion of ice in the compression system of commercial gas turbine engines operating in high ice water content conditions is a safety issue being studied by the aviation community. While most of the research focuses on the underlying physics of ice accretion and the meteorological conditions in which accretion can occur, a systems-level perspective on the topic lends itself to potential near-term operational improvements. Here a detection algorithm is developed which has the capability to detect the impact of ice accretion in the Low Pressure Compressor of an aircraft engine during steady flight as well as during changes in altitude. Unfortunately, the algorithm as implemented was not able to distinguish throttle changes from ice accretion and thus more work remains to be done.

detection↗

NASA NTRSDate not supplied

The Impact of Ice Sheet Surface Representation on Surface Mass Balance in the Goddard Earth Observing System

Surface conditions and their impacts on surface mass balance (SMB) play important roles in ice sheet dynamics and ice sheet interactions with the overlying atmosphere and surrounding ocean. The NASA Global Modeling and Assimilation Office’s (GMAO) Goddard Earth Observing System (GEOS) – an ecosystem of models and reanalyses – represent ice sheet and glacier SMB components, including prognostic surface albedo evolution, fractional snow cover, and snowpack hydrology and meltwater retention. We find the successful representation of ice sheet surface mass balance in MERRA-2, and similar systems, is partly due to compensating biases in surface energy budget. In the atmospheric system, subsequent changes to cloud microphysics and in the longwave radiative transfer model are found to have reduced biases in surface net longwave radiation fluxes while exacerbating surface net shortwave radiation biases, producing erroneously high near-surface temperatures and surface melt in summer months. These issues can be exacerbated by poor experiment initialization and the use of two-moment cloud microphysics within the GEOS ocean-atmosphere coupled system. Here, we document the spatial and temporal extent and causes of these biases in the ice sheet surface energy budget across GEOS systems and implement a range of model improvements to mitigate these issues. We examine the combined impact on these changes on regional energy budget and SMB using both free running and replay experiments (to simulate the impact in reanalyses). Overall, these improvements increase modeled ice sheet surface realism and provide a strong basis for more accurate ice sheet SMB in GMAO’s future reanalyses and forecasting systems.

Lauren C Andrews↗

NASA NTRS2017

Computational Modeling Approaches to Multiscale Design of Icephobic Surfaces

To aid in the design of surfaces that prevent icing, a model and computational simulation of impact ice formation at the single droplet scale was implemented. The nucleation of a single supercooled droplet impacting on a substrate, in rime ice conditions, was simulated. Open source computational fluid dynamics (CFD) software was used for the simulation. To aid in the design of surfaces that prevent icing, a model of impact ice formation at the single droplet scale was proposed•No existing model simulates simultaneous impact and freezing of a single super-cooled water droplet•For the 10-week project, a low-fidelity feasibility study was the goal.

adhesion↗

NASA NTRS1946

An Investigation of the Icing and Heated-air De-icing Characteristics of the R-2600-13 Induction System

A laboratory investigation was made on a Holley 1685-HB carburetor mounted on an R-2600-13 supercharger assembly to determine the icing characteristics and the heated-air de-icing requirements of this portion of the B-25D airplane induction system. Icing has been found to be most prevalent at relatively small throttle openings and, consequently, all runs were made at simulated 60-percent normal rated power condition. Icing characteristics were determined during a series of 15-minute runs over a range of inlet-air conditions. For the de-icing investigation severe impact ice was allowed to form in the induction system and the time required for the recovery of 95 percent of the maximum possible air flow at the original throttle setting was then determined for a range of wet-bulb temperatures. Results of these runs showed that ice on the walls of the carburetor adapter and on the rim of the impeller-shroud portion of the supercharger diffuser plate did not affect engine operation at 60-percent normal rated power. Ice that adversely affected the air flow and the fuel-air ratio was formed only on the central web of the carburetor and then only when the inlet air was saturated or contained free moisture in excess of saturation. No serious ice formations were observed at inlet-air temperatures above 66 0 F or with an inlet-air enthalpy greater than 34 Btu per pound. The maximum temperature at. which any trace of icing could be detected was 1110 F with a relative humidity of approximately 28 percent, The air-flow recovery time for emergency de-icing was 0.3 minute for.an enthalpy of 35 Btu per pound or wet-bulb temperature of 68 0 F. Further increase in enthalpy and wet-bulb temperature above these values resulted in very slight improvement in recovery time. The fuel-air ratio restored by a 5-Minute application of heated air was approximately 7 percent less than the initial value for cold-air conditions.

Chapman, Gilbert E.↗

NASA NTRS1992

A combined analytical-experimental tensile test technique for brittle materials

A semiconventional tensile test technique is developed for impact ices and other brittle materials. Accurate results have been obtained on ultimate strength and modulus of elasticity in a refrigerated ice test. It is noted that the technique can be used to determine the physical properties of impact ices accreted inside icing wind tunnels or other brittle materials.

Chu, M. L.↗