Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “INKS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Ink-jet printing of silver metallization for photovoltaics

The status of the ink-jet printing program at Purdue University is described. The drop-on-demand printing system was modified to use metallo-organic decomposition (MOD) inks. Also, an IBM AT computer was integrated into the ink-jet printer system to provide operational functions and contact pattern configuration. The integration of the ink-jet printing system, problems encountered, and solutions derived were described in detail. The status of ink-jet printing using a MOD ink was discussed. The ink contained silver neodecanate and bismuth 2-ethylhexanoate dissolved in toluene; the MOD ink decomposition products being 99 wt% AG, and 1 wt% Bi.

Vest, R. W.↗

Investigation of the Microstructure and Rheology of Iridium Oxide Catalyst Inks for Low-Temperature Polymer Electrolyte Membrane Water Electrolyzers

Here, we present an investigation of the structure and rheological behavior of catalyst inks for low-temperature polymer electrolyte membrane water electrolyzers. The ink consists of iridium oxide (IrO 2 ) catalyst particles and a Nafion ionomer dispersed in a mixture of 1-propanol and water. The effects of ionomer concentration and catalyst concentration on the microstructure of the catalyst ink were studied. Studies on dilute inks (0.1 wt % IrO 2 ) using zeta potential and dynamic light scattering measurements indicated a strong adsorption of the ionomer onto the catalyst particles which resulted in an increase in the ..zeta..-potential and the z-average diameter. Steady-shear and dynamic-oscillatory-shear rheological measurements of concentrated IrO 2 dispersions (35 wt % IrO 2 ) indicated that the particles are strongly agglomerated in the absence of the ionomer. The addition of even a small amount of the ionomer (2.4 wt % with respect to total solids) caused the rheology to transition from shear thinning to Newtonian because of the reduction in agglomerated structure due to stabilization of the aggregates by the ionomer, consistent with the behavior of dilute inks. At intermediate ionomer loadings, between 2.4 and 9 wt %, the viscosity increased with increasing ionomer wt %, though remained Newtonian, predominantly due to the increasing ionomer volume fraction in the ink. For ionomer loadings greater than 9 wt %, the particles were found to be flocculated, likely induced by a dispersed ionomer. The flocculated inks exhibited strong shear-thinning and gel-like behaviors in steady-shear and oscillatory-shear rheology. The onset of flocculation was found to be sensitive to the catalyst concentration, where below 35 wt % of IrO 2 , flocculation was not observed. The rheological observations were further verified by ultra-small-angle X-ray scattering.

36 MATERIALS SCIENCE↗

Experimental and Theoretical Analysis of Ink Dispersion Stability for Polymer Electrolyte Fuel Cell Applications

The aggregate size in fuel cell catalyst inks depends on the type of dispersion medium, particle concentration, and addition of stabilizing agents. In this work, ink stability and particle size of carbon black and carbon black/Nafion dispersions in four non-aqueous media, viz., methanol, ethanol, isopropanol and ethyl acetate are studied. Based on visual inspection, isopropanol is found to be the best medium for dispersion of carbon black inks. To rationalize this observation, a semi-empirical model based on diffusion-limited aggregation was developed to evaluate the rate of particle aggregation and predict the ink stability time for each dispersion medium. The proposed model supports the experimental observation by qualitatively predicting the same relationship between carbon stability and the dispersion media. The model also showed that the dielectric constant of the dispersion medium and the particle zeta potential are primarily responsible for the ink stability. Particle size for the different inks was determined by dynamic light scattering with and without dilution. Experimental results show that Nafion is a strong stabilizing agent, increasing the ink stability and decreasing the particle size of carbon aggregates. The beneficial effects of Nafion are independent of its concentration and are observed even at Nafion volume fractions of 10 wt%. The interaction energy is found to be a strong function of the surface potential for the dispersion medium with a higher dielectric constant.

25 ENERGY STORAGE↗

Block Polyelectrolyte Additives That Modulate the Viscoelasticity and Enhance the Printability of Gelatin Inks at Physiological Temperatures

We demonstrate the utility of block polyelectrolyte (bPE) additives to enhance viscosity and resolve challenges with the three-dimensional (3D) printability of extrusion-based biopolymer inks. The addition of oppositely charged bPEs to solutions of photocurable gelatin methacryloyl (GelMA) results in complexation-driven self-assembly of the bPEs, leading to GelMA/bPE inks that are printable at physiological temperatures, representing stark improvements over GelMA inks that suffer from low viscosity at 37 °C, leading to low printability and poor structural stability. The hierarchical microstructure of the self-assemblies (either jammed micelles or 3D networks) formed by the oppositely charged bPEs, confirmed by small-angle X-ray scattering, is attributed to the enhancements in the shear strength and printability of the GelMA/bPE inks. Varying bPE concentration in the inks is shown to enable tunability of the rheological properties to meet the criteria of pre- and postextrusion flow characteristics for 3D printing, including prominent yielding behavior, strong shear thinning, and rapid recovery upon flow cessation. Moreover, the bPE self-assemblies also contribute to the robustness of the photo-cross-linked hydrogels; photo-cross-linked GelMA/bPE hydrogels are shown to exhibit higher shear strength than photo-cross-linked GelMA hydrogels. Last, the assessment of the printability of GelMA/bPE inks indicates excellent printing performance, including minimal swelling postextrusion, satisfactory retention of the filament shape upon deposition, and satisfactory shape fidelity of the various printed constructs. We envision this study to serve as a practical guide for the printing of bespoke extrusion inks where bPEs are used as scaffolds and viscosity enhancers that can be emulated in a range of photocurable precursors.

36 MATERIALS SCIENCE↗

High Performance Composite Dielectric Ink for Ultracapacitors

The present invention is a dielectric ink and means for printing using said ink. Approximately 10-20% of the ink is a custom organic vehicle made of a polar solvent and a binder. Approximately 30-70% of the ink is a dielectric powder having an average particle diameter of approximately 10-750 nm. Approximately 5-15% of the ink is a dielectric constant glass. Approximately 10-35% of the ink is an additional amount of solvent. The ink is deposited on a printing substrate to form at least one printed product, which is then dried and cured to remove the solvent and binder, respectively. The printed product then undergoes sintering in an inert gas atmosphere.

Rolin, Terry D.↗

Rheological Investigation on the Microstructure of Fuel Cell Catalyst Inks

We present a rheological investigation of fuel cell catalyst inks. The effects of ink parameters, which include carbon black-support structure, Pt presence on carbon support (Pt-carbon), and ionomer (Nafion) concentration, on the ink microstructure of catalyst inks were studied using rheometry in combination with ultrasmall-angle X-ray scattering (USAXS) and dynamic light scattering (DLS). Dispersions of a high-surface-area carbon (HSC), or Ketjen black type, demonstrated a higher viscosity than Vulcan XC-72 carbon due to both a higher internal porosity and a more agglomerated structure that increased the effective particle volume fraction of the inks. The presence of Pt catalyst on both the carbon supports reduced the viscosity through electrostatic stabilization. For carbon-only dispersions (without Pt), the addition of ionomer up to a critical concentration decreased the viscosity due to electrosteric stabilization of carbon agglomerates. However, with Pt-carbon dispersions, the addition of ionomer showed contrasting behavior between Vulcan and HSC supports. In the Pt-Vulcan dispersions, the effect of ionomer addition on the rheology was qualitatively similar to Vulcan dispersions without Pt. The Pt-HSC dispersions showed an increased viscosity with ionomer addition and a strong shear-thinning nature, indicating that Nafion likely flocculated the Pt-HSC aggregates. These results were verified using DLS and USAXS. Further, the observations of the effect of ionomer:carbon ratio and a comparison between carbons of different surface areas provided insights on the microstructure of the catalyst ink corresponding to the optimized I/C ratio for fuel cell performance reported in the literature.

36 MATERIALS SCIENCE↗

Metal-Complex Inks for Lower Cost and Improved Passivation for Silicon Photovoltaic Metallization

This contribution introduces the silicon PV community to screen-printable metal-complex inks that potentially will reduce Ag usage in Si PV metallization to one-quarter and costs to one-third that of traditional particle-based pastes while also improving passivation. Metal-complex inks are formulated using a Tollen's reaction to produce inks with a high percentage of diamminesilver (I) cations (22 wt %) in a solution of acetate and formate anions. When printed and dried labile ammonia ligands evaporate, leaving behind silver cations which, when reduced by formate anions and acetic acid, plate out silver and silver acetate. When annealed to just 300 degrees C a dense metallic silver film forms with excellent conductivity, and adhesion to silicon. When compared to traditional particle-based screen-printing pastes, the metal-complex inks are much denser, have higher conductivity, use less Ag, and are a fraction of the cost. Importantly, the inks anneal from 90 - 450 degrees C allowing for better passivation schemes than fired SiNx. This contribution highlights first experiments on the improved passivation of metallized poly-Si/SiO2 passivated contacts using metal-complex, Ag inks compared with particle-based, fired pastes.

metal-complex ink↗

Multicolor Inks of Black Phosphorus for Midwave‐Infrared Optoelectronics

Abstract Black phosphorus (bP) based ink with a bulk bandgap of 0.33 eV ( λ = 3.7 µm) has recently been shown to be promising for large‐area, high performance mid‐wave infrared (MWIR) optoelectronics. However, the development of multicolor bP inks expanding across the MWIR wavelength range has been challenging. Here a multicolor ink process based on bP with spectral emission tuned from 0.28 eV ( λ = 4.4 µm) to 0.8 eV ( λ = 1.5 µm) is demonstrated. Specifically, through the reduction of bP particle size distribution (i.e., lateral dimension and thickness), the optical bandgap systematically blueshifts, reaching up to 0.8 eV. Conversely, alloying bP with arsenic (bP 1− x As x ) induces a redshift in the bandgap to 0.28 eV. The ink processed films are passivated with an infrared‐transparent epoxy for stable infrared emission in ambient air. Utilizing these multicolor bP‐based inks as an infrared light source, a gas sensing system is demonstrated that selectively detects gases, such as CO 2 and CH 4 whose absorption band varies around 4.3 and 3.3 µm, respectively. The presented ink formulation sets the stage for the advancement of multiplex MWIR optoelectronics, including spectrometers and spectral imaging using a low‐cost material processing platform.

Kim, Jae Ik↗

Direct Writing of Additive-Free MXene-in-Water Ink for Electronics and Energy Storage

Additive-free, single step formulations of MXene-in-water inks are developed from clay-like titanium carbide (Ti 3 C 2 ) sediments. Solution-processable Ti 3 C 2 inks are compatible with stamping, printing, painting, and writing on a variety of substrates. Specifically, MXene-in-water inks at higher concentrations of 30 mg mL -1 are employed in commercially available pens for dispensing and patterning 2D MXene directly. These MXene pens are employed either manually or automatically using an AxiDraw, enabling direct-writing and complex patterning of functional MXene devices. Versatile MXene pens show compatible writing on a variety of substrates, including paper and polymers, where the deposited ink is used as a passive circuit, similar to silver and copper nanoparticle inks. Written MXene lines without additional post-treatment exhibit length dependent resistance, showing typical resistivity values between carbon based and metal nanoparticle inks. Current collector-free fabrication of MXene micro-supercapacitors is demonstrated on unconventional platforms including paper, textiles, and curved surfaces directly.

catalysis (heterogeneous)↗

The Role of Liquid Ink Transport in the Direct Placement of Quantum Dot Emitters onto Sub-Micrometer Antennas by Dip-Pen Nanolithography

Here, dip-pen nanolithography (DPN) is used to precisely position core/thick-shell (“giant”) quantum dots (gQDs; ≥10 nm in diameter) exclusively on top of silicon nanodisk antennas (≈500 nm diameter pillars with a height of ≈200 nm), resulting in periodic arrays of hybrid nanostructures and demonstrating a facile integration strategy toward next-generation quantum light sources. A three-step reading-inking-writing approach is employed, where atomic force microscopy (AFM) images of the pre-patterned substrate topography are used as maps to direct accurate placement of nanocrystals. The DPN “ink” comprises gQDs suspended in a non-aqueous carrier solvent, o-dichlorobenzene. Systematic analyses of factors influencing deposition rate for this non-conventional DPN ink are described for flat substrates and used to establish the conditions required to achieve small (sub-500 nm) feature sizes, namely: dwell time, ink-substrate contact angle and ink volume. Finally, it is shown that the rate of solvent transport controls the feature size in which gQDs are found on the substrate, but also that the number and consistency of nanocrystals deposited depends on the stability of the gQD suspension. In conclusion, the results lay the groundwork for expanded use of nanocrystal liquid inks and DPN for fabrication of multi-component nanostructures that are challenging to create using traditional lithographic techniques.

36 MATERIALS SCIENCE↗

Additive‐Free Aqueous MXene Inks for Thermal Inkjet Printing on Textiles

Abstract Direct printing of functional inks onto flexible substrates allows for scalable fabrication of wearable electronics. However, existing ink formulations for inkjet printing require toxic solvents and additives, which make device fabrication more complex, limit substrate compatibility, and hinder device performance. Even water‐based carbon or metal nanoparticle inks require supplemental surfactants, binders, and cosolvents to produce jettable colloidal suspensions. Here, a general approach is demonstrated for formulating conductive inkjet printable, additive‐free aqueous Ti 3 C 2 T x MXene inks for direct printing on various substrates. The rheological properties of the MXene inks are tuned by controlling the Ti 3 C 2 T x flake size and concentration. Ti 3 C 2 T x ‐based electrical conduits and microsupercapacitors (MSCs) are printed on textile and paper substrates by optimizing the nozzle geometry for high‐resolution inkjet printing. The chemical stability and electrical properties of the printed devices are also studied after storing the devices for six months under ambient conditions. Current collector‐free, textile‐based MSCs show areal capacitance values up to 294 mF cm −2 (2 mV s −1 ) in poly(vinyl alcohol)/sulfuric acid gel electrolyte, surpassing reported printed MXene‐based MSCs and inkjet‐printed MSCs using other 2D nanomaterials. This work is an important step toward increasing the functional capacity of conductive inks and simplifying the fabrication of wearable textile‐based electronics.

Uzun, Simge↗

Shelf-life of ball-milled catalyst inks for the fabrication of fuel cell electrodes

A major factor driving fuel cell costs is the quantity of precious metal required. Therefore, it is important to understand a timeframe where inks can be reused. Here, in this work, we explore differences between a freshly prepared catalyst ink and one that has been stored for over a year – comparing ink properties, cathode catalyst layer microstructure, and their respective fuel cell performance. Ink studies revealed smaller agglomerate sizes and a decrease in shear viscosity for the aged ink. Longer storage time also results in fewer cracks and a more uniform ionomer distribution, as evidenced by microscopy characterization of rod-coated electrodes. Lastly, polarization curves show improved performance at higher current densities for the electrode prepared from the aged ink. We rationalize such effect in terms of enhanced ionomer adsorption onto the catalyst over time.

08 HYDROGEN↗

Additive-free MXene inks and direct printing of micro-supercapacitors

Direct printing of functional inks is critical for applications in diverse areas including electrochemical energy storage, smart electronics and healthcare. However, the available printable ink formulations are far from ideal. Either surfactants/additives are typically involved or the ink concentration is low, which add complexity to the manufacturing and compromises the printing resolution. Here, we demonstrate two types of two-dimensional titanium carbide (Ti 3 C 2 T x ) MXene inks, aqueous and organic in the absence of any additive or binary-solvent systems, for extrusion printing and inkjet printing, respectively. We show examples of all-MXene-printed structures, such as micro-supercapacitors, conductive tracks and ohmic resistors on untreated plastic and paper substrates, with high printing resolution and spatial uniformity. The volumetric capacitance and energy density of the all-MXene-printed micro-supercapacitors are orders of magnitude greater than existing inkjet/extrusion-printed active materials. The versatile direct-ink-printing technique highlights the promise of additive-free MXene inks for scalable fabrication of easy-to-integrate components of printable electronics.

36 MATERIALS SCIENCE↗

Formulation of Conductive Inks for DIW Printed Battery Electrodes

Ink formulations for DIW printing of Li ion battery electrodes were optimized for high conductivity, surface area and printability. Our focus is particularly on optimizing Li-ion battery electrodes for low temperature applications by 3-D printing the cathodes into high surface area shapes. The sluggish kinetics of ion transport at the solid-electrolyte phase boundary can be a major problem in batteries at low temperatures, so optimizing for ion transport can help combat these issues. Two families of DIW ink were investigated; aqueous conductive polymer suspension with graphene nano platelets (GNP) ink, and “oil in water” graphene oxide (GO) micro emulsion ink which carbonizes to an open cell graphene aerogel. By iterative formulation changes, the conductivity of PEDOT:PSS based ink was increased over tenfold, and stiffness of GO emulsion ink was increased to provide better printability without sacrificing porosity.

36 MATERIALS SCIENCE↗

Metal-Complex Inks for Lower Cost and Improved Passivation for Silicon Photovoltaic Metallization

This contribution introduces the silicon PV community to screen-printable metal-complex inks that potentially will reduce Ag usage in Si PV metallization to one-quarter and costs to one-third that of traditional particle-based pastes while also improving passivation. Metal-complex inks are formulated using a Tollen’s reaction to produce inks with a high percentage of diamminesilver (I) cations (22 wt %) in a solution of acetate and formate anions. When printed and dried, labile ammonia ligands evaporate, leaving behind silver cations which, when reduced by formate anions and acetic acid, plate out silver and silver acetate. When annealed to just 300 °C a dense metallic silver film forms with excellent conductivity, and adhesion to silicon. When compared to traditional particle-based screen-printing pastes, the metal-complex inks are much denser, have higher conductivity, use less Ag, and are a fraction of the cost. Importantly, the inks anneal from 90 – 450 °C allowing for improved passivation schemes compared with fired SiNx. This contribution highlights first experiments on the improved passivation of metallized poly-Si/SiO2 passivated contacts using metal-complex Ag inks.

Young, David L. (ORCID:0000000340970493)↗

Properties of conductive thick-film inks

Ten different conductive inks used in the fabrication of thick-film circuits were evaluated for their physical and handling properties. Viscosity, solid contents, and spectrographic analysis of the unfired inks were determined. Inks were screened on ceramic substrates and fired for varying times at specified temperatures. Selected substrates were given additional firings to simulate the heat exposure received if thick-film resistors were to be added to the same substrate. Data are presented covering the (1) printing characteristics, (2) solderability using Sn-63 and also a 4 percent silver solder, (3) leach resistance, (4) solder adhesion, and (5) wire bonding properties. Results obtained using different firing schedules were compared. A comparison was made between the various inks showing general results obtained for each ink. The changes in firing time or the application of a simulated resistor firing had little effect on the properties of most inks.

Holtze, R. F.↗

Apparatuses and methods for removal of ink buildup

A substrate patterning method including the steps of spraying ink on a surface of a substrate, the spraying of the ink resulting in an overspray of excess ink past an edge of the substrate; changing a temperature of the excess ink to cause a change in a viscosity of the excess ink; and removing the excess ink having the changed viscosity.

36 MATERIALS SCIENCE↗

Investigation of Reactive Silver Ink Formula for Reduced Silver Consumption in Silicon Heterojunction Metallization

Silver is the most expensive non-silicon component in photovoltaic cells. This is particularly salient for silicon heterojunction (SHJ) cells, which rely on large quantities of low-temperature silver pastes (LT-SP). SHJ cells would benefit greatly from an industrially scalable metallization process that simultaneously offers low silver consumption, low finger resistivities (<20 μΩ·cm), and low processing temperatures. Printed reactive silver inks (RSI) are an innovative candidate to this end. Furthermore, this work furthers the research on RSI metallization by investigating the impact of ink formula on properties pertinent to SHJ cells, including electrical properties, line width, ink splatter, silver consumption, cell performance, and adhesion. We introduce a scalable, high-throughput flexible needle contact printing approach for metallization that solves many of the issues associated with drop-on-demand printing. The printed silver fingers are characterized using electrical measurements and top-down and cross-sectional microscopy. The best performing ink, consisting of silver acetate, ethylamine, and formic acid, achieved silver fingers with total resistivities of 3.1 μΩ·cm and contact resistivities of 3.2 mΩ·cm 2 when printed at 61 °C. This ink metallized a full-sized 156 mm × 156 mm SHJ cell. This is the first reported data for RSI metallization of a full-sized SHJ cell and shows how an optimized RSI can achieve similar performances to LT-SP while consuming 80–90% less silver.

14 SOLAR ENERGY↗