Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Homojunction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Characterization of n-Type Iodine-Doped and Indium-Doped CdTe/Cd-Se-Te Thin Films Fabricated by Close-Spaced Sublimation Epitaxy

In this study, n-type CdTe thin films, specifically iodine-doped CdTe (CdTe:I), indium-doped CdTe (CdTe:In), and indium-doped Cd-Se-Te (CST:In), were synthesized using close-spaced sublimation epitaxy (CSSE). Characterization techniques secondary ion mass spectrometry (SIMS), electron backscatter diffraction (EBSD), Hall-effect measurements, and time-resolved photoluminescence (TRPL) were employed to analyze the chemical, structural, and electronic properties of these materials. The results indicated epitaxial single crystal CSSE films grew on the single crystal substrates, with carrier density ranging from 10^14 - 10^16 cm -3 , and after post-annealing, the minority-carrier lifetimes reach near the radiative limit. Additionally, a preliminary exploration of homojunction structures with an n- type (CdTe:In /CST:In /CdTe:I) /CdTe:P /Cu /Mo configuration was performed. The best device performance was achieved with CdTe:I including CdS aiding in band alignment, resulting in a power conversion efficiency (..eta..) of 2.61% with open circuit voltage (Voc) of 850 mV, fill factor (FF) of 47.8%, and short-circuit current (Jsc) of 6.44 mA/cm 2 . The observed low Jsc and efficiency may be attributed to a buried junction and a poor interface, due to dopant interdiffusion. Consequently, further investigations focusing on interface optimization, diffusion blocking, and reduced recombination through passivation, are crucial to enhancing the efficiency of CSSE CdTe homojunction devices in the future.

cadmium compounds↗
NASA NTRS1981

High-efficiency thin-film GaAs solar cells, phase2

Thin GaAs epi-layers with good crystallographic quality were grown using a (100) Si-substrate on which a thin Ge epi-interlayer was grown by CVD from germane. Both antireflection-coated metal oxide semiconductor (AMOS) and n(+)/p homojunction structures were studied. The AMOS cells were fabricated on undoped-GaAs epi-layers deposited on bulk poly-Ge substrates using organo-metallic CVD film-growth, with the best achieved AM1 conversion efficiency being 9.1%. Both p-type and n(+)-type GaAs growth were optimized using 50 ppm dimethyl zinc and 1% hydrogen sulfide, respectively. A direct GaAs deposition method in fabricating ultra-thin top layer, epitaxial n(+)/p shallow homojunction solar cells on (100) GaAs substrates (without anodic thinning) was developed to produce large area (1 sq/cm) cells, with 19.4% AM1 conversion efficiency achieved. Additionally, an AM1 conversion efficiency of 18.4% (17.5% with 5% grid coverage) was achieved for a single crystal GaAs n(+)/p cell grown by OM-CVD on a Ge wafer.

Yeh, Y. C. M.↗
NASA NTRS1984

Applicability of the Meyer-Neldel rule to solar cells

A comparison of data taken on high quality silicon, GaAs, and GaInAs solar cells with those taken on a variety of homojunction, heterojunction, and metal-insulator-semiconductor devices indicates that while the Meyer-Neldel rule may be applicable to certain types of solar cells it is not applicable to well-behaved, diffusion-controlled homojunction devices. It cannot be used, therefore, as a universal rule to predict maximum achievable solar cell voltages.

Goradia, C.↗
NASA NTRS1987

Recent developments in indium phosphide space solar cell research

Recent developments and progress in indium phosphide solar cell research for space application are reviewed. Indium phosphide homojunction cells were fabricated in both the n+p and p+n configurations with total area efficiencies of 17.9 and 15.9% (air mass 0 and 25 C) respectively. Organometallic chemical vapor deposition, liquid phase epitaxy, ion implantation and diffusion techniques were employed in InP cell fabrication. A theoretical model of a radiation tolerant, high efficiency homojunction cell was developed. A realistically attainable AMO efficiency of 20.5% was calculated using this model with emitter and base doping of 6 x 10 to the 17th power and 5 x 10 the the 16th power/cu cm respectively. Cells of both configurations were irradiated with 1 MeV electrons and 37 MeV protons. For both proton and electron irradiation, the n+p cells are more radiation resistant at higher fluences than the p+n cells. The first flight module of four InP cells was assembled for the Living Plume Shield III satellite.

Brinker, David J.↗
NASA NTRS1987

Recent developments in indium phosphide space solar cell research

Recent developments and progress in indium phosphide solar cell research for space application are reviewed. Indium phosphide homojunction cells were fabricated in both the n + p and p + n configurations with total area efficiencies of 17.9 and 15.9 percent (air mass 0 and 25 C) respectively. Organometallic chemical vapor deposition, liquid phase epitaxy, ion implantation and diffusion techniques were employed in InP cell fabrication. A theoretical model of a radiation tolerant, high efficiency homojunction cell was developed. A realistically attainable AM0 efficiency of 20.5 percent was calculated using this model with emitter and base doping of 6 x 10 to the 17th power and 5 x 10 to the 16th power/cu cm, respectively. Cells of both configurations were irradiated with 1 MeV electrons and 37 MeV protons. For both proton and electron irradiation, the n + p cells are more radiation resistant at higher fluences than the p + n cells. The first flight module of four InP cells was assembled for the Living Plume Shield III satellite.

Brinker, David J.↗
NASA NTRS1988

Predicted performance of near-optimally designed indium phosphide space solar cells at high intensities and temperatures

The authors calculated the expected performance dependence of near-optimally designed shallow homojunction n+pp+ InP solar cells on incident intensities up to 200 AM0 and temperatures up to 100 deg C (373 K). Both circular and rectangular cells were considered, the former for use in a Cassegrainian concentrator array at 100 AM0, 80-100 deg C and the latter for use in a Slats concentrator array at 20 AM0, 80-100 deg C. With efficiencies near 22 percent at 80 deg C, both the circular and rectangular InP shallow homojunction solar cells compare very favorably to GaAs cells of the same design and may be preferable to the GaAs cells for space applications because of the superior radiation tolerance of the InP cells.

Goradia, Chandra↗
NASA NTRS1991

Two-terminal monolithic InP-based tandem solar cells with tunneling intercell ohmic connections

A monolithic two-terminal InP/InGaAsP tandem solar cell was successfully fabricated. This tandem solar cell consists of a p/n InP homojunction top subcell and a 0.95 eV p/n InGaAsP homojunction bottom subcell. A patterned 0.95 eV n(+)/p(+) InGaAsP tunnel diode was employed as an intercell ohmic connection. The solar cell structure was prepared by two-step liquid phase epitaxial growth. Under one sun, AM1.5 global illumination, the best tandem cell delivered a conversion efficiency of 14.8 pct.

Shen, C. C.↗
DOE OSTI2023

High-Performance Passivating Contacts for Si PV Based on Engineered, Doped Nanopinholes through Dielectric Layers

We present a novel, industrially relevant method to fabricate high-performance poly-Si passivating contacts for Si PV. Passivating contacts based on SiOx/poly-Si layer stacks have been implemented in record-efficiency homojunction Si solar cells. In this technology, the carrier transport through a surface-passivating SiOx is enabled either by quantum-tunneling or nanopinholes. The doped poly-Si layer provides charge-carrier selectivity. Previously, the ISFH research group demonstrated a record 26.1% efficient Si homojunction cell, where transport pinholes in ~2 nm SiOx were produced by thermal breakdown at > 1000 degrees C, which is hard to control and is surface morphology-dependent. At room temperature, our new process uses electroless plating of Ag nanoparticles, followed by metal-assisted chemical etching. Nanogalvanic corrosion yields < 20 nm-wide nanopinholes in an insulating > 2 nm SiOx layer. The nanopinholes are filled by a heavily doped a-Si:H overlayer. We drive in the dopants into the Si wafer with subsequent high-temperature annealing. Preferential incorporation of dopants at pinhole locations results in nanoscale p+/n or n+/n junctions near the wafer interface. Each heavily-doped nanoscale pinhole junction collects and transports photogenerated carriers to the cell metal contacts. The density of the engineered nanopinholes can be tuned over a wide range which is critical for optimization of device performance. The same nanogalvanic corrosion principles can be applied to produce doped transport pinholes in well-passivating thick dielectric SiOx/SiNy stacks. Importantly, our process does not rely on thermal breakdown of the dielectric layers and can be applied to textured wafers resulting in Si solar cells with > 20% conversion efficiency.

dielectric layer↗
DOE OSTI2026

Design and simulation of n -type solar cells based on an iodine-doped CdTe absorber using SCAPS-1D

The performance of conventional p-type CdTe solar cells has plateaued in recent years, motivating exploration of n-type absorbers. Here, we evaluate a homojunction solar cell employing iodine-doped CdTe (CdTe:I) as the absorber in a Ti 3 C 2 T x MXene/p-CdTe:As/n-CdTe:I/indium structure through SCAPS-1D simulations and prototype devices. Optimized simulations predict efficiencies above 25% for thin CdTe:I absorbers (~0.7 μm). In contrast, the first prototype achieved only ~1.36% efficiency with V OC = 0.48 V, J SC = 6.45 mA/cm 2 and FF = 43.8%. When the simulation is adjusted to match the actual device structure, and the effective illumination is reduced to account for front-side light loss, the predicted V OC (0.48 V) and JSC (6.74 mA/cm 2 ) closely reproduce the experimental values. This suggests that the device performance is primarily limited by reduced front-side photon transmission and other material non-idealities. These results highlight the promise of iodine-doped n-type CdTe and identify clear pathways for further efficiency improvement.

14 SOLAR ENERGY↗
DOE OSTI2022

Metastability and Degradation of CdTe Solar Cells Investigated by nm-Scale Electrical Potential Imaging

We report on investigations of reversible metastability and irreversible degradation of MZO/CdSeTe/CdTe devices from the perspective of electric field across the device using Kelvin probe force microscopy (KPFM). The device showed reversible transitions between the light-soak state (LSS) with the best device efficiency and the dark-soak state (DSS) with an inferior efficiency. However, it showed an irreversible degradation state (DgS) driven by long-hour light soaking at an elevated temperature. The nm-scale KPFM electric field imaging on cross-sections of the devices revealed different anomalous electric field profiles. The electric field at the LSS exhibits a main peak inside the CdSeTe layer but not at the MZO/CdSeTe heterointerface, demonstrating that working junction of the device is a buried homojunction (BHJ). At the DSS, a second electric field peak was observed at the MZO/CdSeTe interface with a similar strength to the main BHJ, which probably caused the decrease in fill factor at the DSS. At the DgS, the electric field peak at the MZO/CdSeTe interface increased significantly and a third electric field was measured at the back contact of the device. Device modeling using COMSOL and in alignment with both the electric field and device current-voltage curves suggest that a slightly low n-doped CdSeTe in the region near the MZO/CdSeTe interface caused the BHJ, and that either a loss of MZO doping or increase of the conduction band offset spike due to long-term stress caused the fill factor-dominated degradation and the increased electric field near the MZO/CdSeTe interface at the DgS. The former, MZO doping decrease, is more plausible by referring the related literature.

BHJ↗
DOE OSTI2026

Probing the Nanoscale Excitonic Landscape and Confinement of Excitons in Gated Monolayer Semiconductors

Engineering and probing excitonic properties at the nanoscale remains a central challenge in quantum photonics and optoelectronics. While exciton confinement via electrical control and strain engineering has been demonstrated in 2D semiconductors, substantial nanoscale heterogeneity limits the scalability of 2D quantum photonic device architectures. Here, in this work, we use cathodoluminescence spectroscopy to probe the excitonic landscape of monolayer WS 2 under electrostatic gating. Exploiting the high spatial resolution of the converged electron beam, we resolve a homojunction arising between gated and ungated regions. Moreover, we reveal an exciton confinement channel arising from an unconventional doping mechanism driven by the interplay between the electron beam and the applied gate fields. These findings offer new insights into the optoelectronic behavior of monolayer semiconductors under the combined influence of electron-beam excitation and electrostatic gating. Our approach provides a pathway for exciton manipulation at the nanoscale and opens opportunities for controlling quantum-confined exciton transport in 2D materials.

2D materials↗
DOE OSTI2022

Zn‐Doped P‐Type InAs Nanocrystal Quantum Dots

Abstract Doped heavy metal‐free III–V semiconductor nanocrystal quantum dots (QDs) are of great interest both from the fundamental aspects of doping in highly confined structures, and from the applicative side of utilizing such building blocks in the fabrication of p–n homojunction devices. InAs nanocrystals (NCs), that are of particular relevance for short‐wave IR detection and emission applications, manifest heavy n‐type character poising a challenge for their transition to p‐type behavior. The p‐type doping of InAs NCs is presented with Zn – enabling control over the charge carrier type in InAs QDs field effect transistors. The post‐synthesis doping reaction mechanism is studied for Zn precursors with varying reactivity. Successful p‐type doping is achieved by the more reactive precursor, diethylzinc. Substitutional doping by Zn 2+ replacing In 3+ is established by X‐ray absorption spectroscopy analysis. Furthermore, enhanced near infrared photoluminescence is observed due to surface passivation by Zn as indicated from elemental mapping utilizing high‐resolution electron microscopy corroborated by X‐ray photoelectron spectroscopy study. The demonstrated ability to control the carrier type, along with the improved emission characteristics, paves the way towards fabrication of optoelectronic devices active in the short‐wave infrared region utilizing heavy‐metal free nanocrystal building blocks.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

Modeling and design of III-V heterojunction solar cells for enhanced performance

Heterojunctions can increase the efficiency of solar cell devices relative to homojunctions, but there is a large parameter space with significant tradeoffs that must be considered. Here, we present an experimental and computational study of III-V heterojunction solar cells and show how the emitter doping, emitter band gap, and heteroband offsets impact device efficiency. Efficiency is maximized by pushing the junction depletion region into the wider band gap material while minimizing the effects of heteroband offsets through optimized choice of emitter band gap, emitter electron affinity, and/or emitter doping density. We use these results to guide optimization of devices grown by halide vapor phase epitaxy, achieving 27% efficiency in a GaAs/GaInPAs heterojunction device. We also show that heterojunctions yield proportionally larger efficiency improvements in lower-quality materials. Although the modeling was developed and validated using III-V materials, the results are theoretically applicable to materials systems outside III-Vs.

14 SOLAR ENERGY↗
DOE OSTI2022

Failure Modes of Platinized pn+-GaInP Photocathodes for Solar-Driven H2 Evolution

The long-term stability for the hydrogen-evolution reaction (HER) of homojunction pn+-Ga0.52In0.48P photocathodes (band gap = 1.8 eV) with an electrodeposited Pt catalyst (pn+-GaInP/Pt) has been systematically evaluated in both acidic and alkaline electrolytes. Electrode dissolution during chronoamperometry was correlated with changes over time in the current density-potential (J-E) behavior to reveal the underlying failure mechanism. Pristine pn+-GaInP/Pt photocathodes yielded an open-circuit photopotential (Eoc) as positive as >1.0 V vs the potential of the reversible hydrogen electrode (RHE) and a light-limited current density (Jph) of >12 mA cm-2 (1-sun illumination). However, Eoc and Jph gradually degraded at either pH 0 or pH 14. The performance degradation was attributed to three different failure modes: (1) gradual thinning of the n+-emitter layer due to GaInP dissolution in acid; (2) active corrosion of the underlying GaAs substrate at positive potentials causing delamination of the upper GaInP epilayers; and (3) direct GaAs/electrolyte contact compromising the operational stability of the device. This work reveals the importance of both substrate stability and structural integrity of integrated photoelectrodes toward stable solar fuel generation.

CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSICS,S↗
DOE OSTI2024

Imaging Valley Excitons in a 2D Semiconductor with Scanning Tunneling Microscope-Induced Luminescence

Valley excitons dominate the optoelectronic response of transition-metal dichalcogenides and are drastically affected by structural and environmental inhomogeneities localized in these materials. Critical to understanding and controlling these nanoscale excitonic changes is the ability to correlate the imaging of excitonic states with crystalline structures on the atomic scale. Here, in this study, we apply scanning tunneling microscope-induced luminescence microscopy to image valley excitons in a semiconducting transition-metal dichalcogenide monolayer decoupled by a 10 nanometer-thick hexagonal-boron-nitride flake incorporated in a lateral homojunction on an Au electrode surface. This design enables the observation of chiral excitonic emission arising from neutral and charged valley excitons of the monolayer semiconductor at ambipolar voltages with a quantum efficiency up to similar to ~10 -5 photon/electron. The measured light helicity demonstrates considerable circular polarization dependent on the sample voltage, reaching as much as 40%. The real-space luminescence imaging maps$-$at subnanometer resolution$-$of the valley excitons reveal striking spatial variations associated with localized inhomogeneities, including surface impurities and possibly nanoscale dielectric and/or potential disorders in the monolayer. Our study introduces a promising format for 2D materials to explore and tailor their optoelectronic processes at the atomic scale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

III-Nitride p-down green (520 nm) light emitting diodes with near-ideal voltage drop

We demonstrate p-down green emitting LEDs with low turn-on voltage enabled by efficient tunnel junctions. Due to the polarization field alignment in the (In,Ga)N/GaN interface with the p-down orientation, the electrostatic depletion barrier for electron and hole injection is reduced when compared with the conventional p-up LEDs. A single (In,Ga)N/GaN heterostructure quantum well active region with a GaN homojunction tunnel junction exhibited very low forward operating voltage of 2.42 V at 20 A/cm 2 with a peak electroluminescence emission wavelength of 520 nm for current densities above 100 A/cm 2 . Furthermore, the bottom tunnel junction with minimal voltage drop enabled excellent hole injection into the bottom p-GaN layer.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Breakdown characteristics analysis of kV-class vertical GaN PIN rectifiers by wafer-level sub-bandgap photoluminescence mapping

This work reports analysis of the reverse-bias breakdown characteristics of homojunction gallium nitride (GaN) p–i–n (PIN) rectifiers fabricated on bulk GaN substrates. Sub-bandgap photoluminescence mapping at room temperature as a contactless, non-destructive wafer inspection method was performed to analyze the impact of material properties on grown GaN PIN diodes and to study the correlation between defect types and breakdown characteristics of vertical GaN PIN rectifiers. Under the sub-bandgap excitation, yellow luminescence is dominant. The premature breakdown characteristics of the fabricated kV-class vertical GaN PIN rectifiers with nitrogen-implanted floating guard rings are found to be associated with material defects and deep level complexes. Photoluminescence mapping has demonstrated its effectiveness in quantitative analysis of dislocations and other types of defects.

42 ENGINEERING↗
DOE OSTI2026

15.3% AM1.5G Efficiency GaAs Solar Cells Fabricated via an Epitaxy-Free Process

Here, we report simple and potentially low-cost techniques for creating high-quality n-type gallium arsenide (GaAs) and GaAs p/n junctions and fabricate GaAs p/n junction solar cells. Detailed-balance modeling suggests that 20% AM1.5G efficiency p/n homojunction devices may be possible if the surface doping concentration can be limited to values less than ∼ 5 × 10 19 cm −3 . Our process exploits an open-tube, vapor-phase, deposition-free, zinc diffusion technique for forming p-type layers in melt-grown n-GaAs substrates that results in sheet resistances less than 1 kΩ/$\square$. In addition, we have improved the minority carrier diffusion lengths of melt-grown GaAs from less than one micron to over five microns using an open-tube, vacuum-free, annealing process which reduces the density of EL2 midgap defects. Finally, we have combined these advances to fabricate epitaxy-free, GaAs solar cells with a validated AM1.5G efficiency of 15.3%.

14 SOLAR ENERGY↗