Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Graphite Properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Effect of heat-treatment temperature of vapor-grown graphite fibers. I - Properties of their bromine intercalation compounds

Vapor-grown graphite fibers were heat treated at 2000, 2200, 2400, 2600, 2800, and 3000 C, brominated at room temperature for two days, and then characterized by X-ray diffraction analysis, differential scanning calorimetry, and resistivity measurements. Fibers greater than 13 microns in diameter had low resistivities (50 microohms or less) irrespective of the heat treatment temperature. An analysis of the results obtained suggests that resistivities below 6 microohms cannot be achieved through a further reduction in defect level unless the amount of bromine is increased.

Gaier, James R.↗
NASA NTRS1987

Space environmental effects on graphite-epoxy compressive properties and epoxy tensile properties

This study characterizes the effects of electron radiation and temperature on a graphite-epoxy composite material. Compressive properties of the T300/934 material system were obtained at -250 F (-157 C), room temperature, and 250 F (121 C). Tensile specimens of the Fiberite 934 epoxy resin were fabricated and tested at room temperature and 250 F (121 C). Testing was conducted in the baseline (nonirradiated) and irradiated conditions. The radiation exposure was designed to simulate 30 year, worst-case exposure in geosynchronous Earth orbit. Mechanical properties tended to degrade at elevated temperature and improve at cryogenic temperature. Irradiation generally degraded properties at all temperatures.

Fox, Derek J.↗
NASA NTRS2005

Modeling and Testing of the Viscoelastic Properties of a Graphite Nanoplatelet/Epoxy Composite

In order to facilitate the interpretation of experimental data, a micromechanical modeling procedure is developed to predict the viscoelastic properties of a graphite nanoplatelet/epoxy composite as a function of volume fraction and nanoplatelet diameter. The predicted storage and loss moduli for the composite are compared to measured values from the same material using three test methods; Dynamical Mechanical Analysis, nanoindentation, and quasi-static tensile tests. In most cases, the model and experiments indicate that for increasing volume fractions of nanoplatelets, both the storage and loss moduli increase. Also, the results indicate that for nanoplatelet sizes above 15 microns, nanoindentation is capable of measuring properties of individual constituents of a composite system. Comparison of the predicted values to the measured data helps illustrate the relative similarities and differences between the bulk and local measurement techniques.

Odegard, Gregory M.↗
NASA NTRS1982

Predictions for partial and monolayer coverages of O2 on graphite

Monolayer properties of O2 on graphite are calculated using a pattern recognition, optimization scheme. Equilibrium monolayers are predicted at two different densities with properties in agreement with recent X-ray diffraction, specific heat, and neutron scattering data. Properties of the extremely low density regime are calculated using a model based upon a distribution of two-dimensional O2 clusters. The results are consistent with experimental evidence.

Pan, R. P.↗
NASA NTRS1987

In-plane and interlaminar Iosipescu shear properties of various graphite fabric/epoxy laminates

The Iosipescu shear test method was used to measure the in-plane and interlaminar shear properties of four T300 graphite fabric/Fiberite 934 epoxy composite materials. Weave geometries tested included an Oxford weave, a 5-harness satin weave, an 8-harness satin weave, and a plain weave with auxiliary warp yarns. Both orthogonal and quasi-isotropic layup laminates were tested. In-plane and interlaminar shear properties were obtained for laminates of all four fabric types. Overall, few differences in shear properties attributable to the fabric weave pattern were observed. However, the auxiliary warp material was significantly weaker and less stiff in interlaminar shear parallel to its fill direction.

Adams, Donald F.↗
NASA NTRS1984

Evaluation of long-duration exposure to the natural space environment on graphite-polyimide and graphite-epoxy mechanical properties (A0175)

The primary objective of this experiment is to accumulate the needed operational data associated with the exposure of graphite-polyimide and graphite-epoxy material to the environments of space. The experiment will be mounted in two 3-in.-deep peripheral trays. Graphite-polyimide specimens will occupy 1 1/3 trays and the graphite-epoxy specimens will occupy two-thirds of a tray. The experiment approach requires two matched sets of specimens with traceable records that are maintained for materials processing and specimen quality. After fabrication, one set of each test specimen will be sectioned and structurally tested to serve as a data baseline. After the flight, the other set of specimens will undergo extensive measurements of mechanical properties for comparison with the original data baseline. Structural testing of the graphite-polyimide specimens will provide strength and elastic data in tension, compression, and shear. Transverse tension microcracking and crack propagation will be evaluated by photomicroscopy. Structural testing of the graphite-epoxy specimens will include verification of laminate, core, adhesive, and fatigue properties as applied to the design and analysis of the payload bay door. Microcracking and crack propagation will also be analyzed by photomicroscopy.

Powell, J. H.↗
NASA NTRS1975

Review of electrical and thermal properties of carbon and graphite

Some of the electrical and thermal properties of ordered and partially ordered carbons are reviewed. Earlier and current research areas are discussed relative to electrical properties of pyrolytic and polycrystalline graphite; thermal, electrical, and magnetic properties of graphitizable and glassy carbon with heat treatment temperatures in the range 600-2500 C; Josephson junction-like and switching behavior in carbon films; and some high-conductivity and superconducting compounds made from carbon. Due to the newness and complexity of many of the areas examined, the results are not always completely understood, nor have these areas been completely investigated experimentally. Suggestions for future research are made.

Woollam, J. A.↗
NASA NTRS1982

Effects of thermal cycling on residual mechanical properties of C6000/PMR-15 graphite polyimide

An experimental study to determine the effects of thermal cycling on residual mechanical properties of a graphite/polyimide composite has been conducted. Interlaminar shear, flexure and compression strengths were measured at room temperature and 316 C on unidirectional and quasi-isotropic laminates subjected to 150 and 500 thermal cycles between -156 C and 316 C. Thermal cycling produced transverse microcracks and delaminations in the laminates. The linear density of the microcracks (35/cm) was about the same after 150 and 500 cycles. Although the crack density did not change from 150 to 500 cycles, crack growth did occur with intralamina cracks growing into adjacent lamina. The matrix controlled properties of the quasi-isotropic laminate at both room temperature and 316 C were significantly reduced by thermal cycling. However, the properties of the unidirectional laminate were significantly reduced only at 316 C.

Tompkins, S. S.↗
NASA NTRS1976

Environmental Effects on Graphite-Epoxy Fatigue Properties

Effects of torsional and flexural fatigue on the long-time Integrity of advanced graphite-epoxy structural composites have been investigated. Torsional fatigue tests were run at stress ratios of R = 0 (zero to maximum, repeated) and R = -1 (zero mean stress) on unidirectional, angleply, and woven graphite fiber materials in air and water at room temperature and at 74 C. Flexural fatigue tests (four-point bending) with R = -1 were run in air and water at room temperature, and with R = 0 in air. Results show that, in torsional cycling, both water environment and higher test temperature contribute to significant degradation of torsional stiffness. The degradation of stiffness from torsional stress cycling was observed to be much greater with R = -1 than with simple R = 0 cycling. The effect of environment also is greater in the fully reversed cycling. Flexural fatigue results on +/- 30 deg material show a large fatigue effect, with fatigue limits of less than 50% and 30% of the static failure strength for specimens tested under stress ratios of R = 0 and R = -1, respectively. Compliance measurements indicate that the final failures are preceded by damage initiation and accumulation, which begins at about 1% of the specimen life.

Sumsion, H. T.↗
NASA NTRS1976

The effect of thermal exposure on the mechanical properties of aluminum-graphite composites

To promote the development of aluminum-graphite composites with improved properties for aerospace applications, composite samples were fabricated by solid-state diffusion bonding of liquid-phase Al-infiltrated Thornel 50 fibers, and their mechanical properties were measured at room temperature in the as-received condition, after temperature exposure and after thermal cycling. The interface structure in aluminum-graphite composites and its effect on the composite properties, the effect of thermal cycling on the tensile properties of the composites, and the characteristics of failures of the composites in tension is discussed. The studied composites exhibited tensile properties corresponding well with those predicted by the rule of mixtures. Thermal cycling between 20 C and 500 C, as well as the formation of the Al4C3 at the Al-graphite interfaces at temperatures above 500 C resulted in degradation of the composite strength. Scanning electron microscopy of fractured surfaces indicated that the relatively weak interface governs the mode of failure in tension.

Khan, I. H.↗
NASA NTRS1972

A study of the effect of selected material properties on the ablation performance of artificial graphite

Eighteen material properties were measured on 45 different, commercially available, artificial graphites. Ablation performance of these same graphites were also measured in a Mach 2 airstream at a stagnation pressure of 5.6 atm. Correlations were developed, where possible, between pairs of the material properties. Multiple regression equations were then formulated relating ablation performance to the various material properties, thus identifying those material properties having the strongest effect on ablation performance. These regression equations reveal that ablation performance in the present test environment depends primarily on maximum grain size, density, ash content, thermal conductivity, and mean pore radius. For optimization of ablation performance, grain size should be small, ash content low, density and thermal conductivity high, and mean pore radius large.

Maahs, H. G.↗
NASA NTRS1984

Effects of high energy radiation on the mechanical properties of epoxy-graphite fiber reinforced composites

The effects of high energy radiation on the mechanical properties and on the molecular and structural properties of graphite fiber reinforced composites were assessed so that the durability of such composites in space applications could be predicted. Investigative techniques including ESR and infrared spectroscopy, ESCA, contact angle measurements, and dynamic and static mechanical testing (3-point bending and interlaminar shear) were employed. The results using these different techniques are individually described, and the implications of the data are discussed. The proposed plan of work for the next fiscal year is outlined.

Fornes, R. E.↗
NASA NTRS1975

Environmental effects on the torsion and flexure fatigue properties of graphite-epoxy composites

Effects of torsional and flexural fatigue on the long-time integrity of advanced graphite-epoxy structural composites have been investigated. Reversed (R = - 1) and unidirectional (R = 0) torsional fatigue tests were made on unidirectional, cross-plied and woven graphite fiber materials in air and water at room temperature and at 74 C. Flexural fatigue tests (4-point bending) with R = - 1 were run in air and water at room temperature, and at R = 0 in air. Results show that in torsional cycling, both water environment and higher test temperature contribute to significant degradation of torsional stiffness. The degradation of stiffness from torsional stress cycling was observed to be much greater with R = - 1 than with simple R = 0 cycling. The effect of environment is also greater in the fully reversed cycling.

Sumsion, H. T.↗
NASA NTRS1985

Tribological properties of graphite-fiber-reinforced, partially fluorinated polyimide composites

Graphite-fiber-reinforced polyimide (GFRPI) composites were formulated from three new partially fluorinated polyimides and three types of graphite fiber. Nine composites were molded into pins and evaluated in a pin-on-disk tribometer. Friction coefficients, wear rates, pin wear surface morphology, and transfer film formation were assessed at 25 and 300 C. Also assessed was the effect of sliding speed on friction. Wear was up to two orders of magnitude lower at 25 C and up to one order of magnitude lower at 300 C than with previously formulated NASA GFRPI composites.

Fusaro, R. L.↗
NASA NTRS1986

Tribological properties of graphite-fiber-reinforced, partially fluorinated polyimide composites

Graphite-fiber-reinforced polyimide (GFRPI) composites were formulated from three new partially fluorinated polyimides and three types of graphite fiber. Nine composites were molded into pins and evaluated in a pin-on-disk tribometer. Friction coefficients, wear rates, pin wear surface morphology, and transfer film formation were assessed at 25 and 300 C. Also assessed was the effect of sliding speed on friction. Wear was up to two orders of magnitude lower at 25 C and up to one order of magnitude lower at 300 C than with previously formulated NASA GFRPI composites.

Fusaro, R. L.↗
NASA NTRS1991

Evaluation of long-duration exposure to the natural space environment on graphite-polyimide and graphite-epoxy mechanical properties

Experiment AO175 involved passive exposure (on oblique leading and trailing faces of LDEF) of carbon-fiber reinforced laminates of epoxy, bismaleimide, and polyimide resins. Post-flight evaluation included: optical examination of exposed surfaces, panel weight and distortion measurements, ultrasonic c-scan inspection, and conventional mechanical testing of coupons machined from the panel.

Vyhnal, Richard F.↗
NASA NTRS1966

Carbon and graphite

Mechanical properties, plastic deformation, and tensile creep rate in carbon and graphite

TENSILE CREEP↗