Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Graphite/Epoxy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Fabrication of graphite/epoxy cases for orbit insertion motors

The fabrication procedures are described for filament-wound rocket motor cases, approximately 26.25 inches long by 25.50 inches diameter, utilizing graphite fibers. The process utilized prepreg tape which consists of Fortafil 4-R fibers in the E-759 epoxy resin matrix. This fabrication effect demonstrated an ability to fabricate high quality graphite/epoxy rocket motor cases in the 26.25 inch by 25.50 inch size range.

Schmidt, W. W.↗
NASA NTRS1974

Developments of a unique graphite/epoxy antenna subreflector

Advanced concepts for large, furlable space antennas have led to an extensive development program at the Jet Propulsion Laboratory (JPL) with configurations utilizing conical main reflectors. The antenna subreflectors for these conical configurations have unusual geometries and new structural requirements. Structural efficiency of the conical antennas is improved through the use of fiber composites. A subreflector was designed and fabricated with graphite/epoxy material. The subreflector is a cylindrical paraboloid with demanding criteria for contour surface precision, high thermal stability, and sufficient structural capacity for inertial launch loads in axial and transverse directions. The paper describes the design, analysis, and fabrication of the subreflector.

Robinson, E. Y.↗
NASA NTRS1974

Design, fabrication and test of graphite/epoxy metering truss structure components, phase 3

The design, materials, tooling, manufacturing processes, quality control, test procedures, and results associated with the fabrication and test of graphite/epoxy metering truss structure components exhibiting a near zero coefficient of thermal expansion are described. Analytical methods were utilized, with the aid of a computer program, to define the most efficient laminate configurations in terms of thermal behavior and structural requirements. This was followed by an extensive material characterization and selection program, conducted for several graphite/graphite/hybrid laminate systems to obtain experimental data in support of the analytical predictions. Mechanical property tests as well as the coefficient of thermal expansion tests were run on each laminate under study, the results of which were used as the selection criteria for the single most promising laminate. Further coefficient of thermal expansion measurement was successfully performed on three subcomponent tubes utilizing the selected laminate.

Source record↗
NASA NTRS1975

Design, fabrication, and test of a Graphite/Epoxy Metering Shell (GEMS)

A program to design, fabricate and test a dimensionally stable metering structure in support of the large space telescope (LST) program is discussed. Graphite/epoxy was the material selected as the only viable candidate material which can meet the stringent thermal expansion criteria of the LST. A metering shell was designed and fabricated, with emphasis on dimensional stability in conjunction with low cost. Thermal expansion test coupons extracted from the layups of the skin panels indicated the attainment of a coefficient of thermal expansion of 0.0666 micrometers/m K. Subsequent thermal vacuum chamber tests on the complete metering shell demonstrated an expansion of the 2.95-meter overall length of 0.27 micrometers/K. Static and dynamics tests, which demonstrated adequacy with respect to limit loads and stiffness, were also accomplished.

Source record↗
NASA NTRS1975

Experimental evaluation of two 36 inch by 47 inch graphite/epoxy sandwich shear webs

The design is described and test of two large (36 in. x 47 in.) graphite/epoxy sandwich shear webs. One sandwich web was designed to exhibit strength failure of the facings at a shear load of 7638 lbs/in., which is a characteristic loading for the space shuttle orbiter main engine thrust beam structure. The second sandwich web was designed to exhibit general instability failure at a shear load of 5000 lbs/in., to identify problem areas of stability critical sandwich webs and to assess the adequacy of contemporary analysis techniques.

Bush, H. G.↗
NASA NTRS1975

Design of a graphite/epoxy metering truss for the Large Space Telescope

This paper presents the design development of a truss-type structure which utilizes graphite/epoxy as the primary material system. A review is given of an on-going NASA sponsored program to develop a structural assembly which is required to have a very high degree of dimensional stability. Methods of material characterization and selection are given along with property data such as strength, stiffness, outgassing and thermal expansion. Finite element (NASTRAN) analysis will be discussed and deflection plots of the lowest mode frequencies will be presented. Proposed full scale tests: static, dynamic, and thermal/vacuum will be described.

Oken, S.↗
NASA NTRS1976

Stress-strain and failure properties of graphite/epoxy laminates

The results of a series of tensile tests on graphite/epoxy laminates at rates varying from 0.002 in/min to 2 in/min are reported. The loads are applied at various angles to the fiber directions in each case. The rate dependent behavior of the stress-strain response is assessed. Evidence is presented to indicate that failure first occurs on inner piles. Also, evidence is presented to indicate that, in some cases, moduli increase with increased stress or strain level. The lamination theory is used to predict moduli and comparisons with experiment are given. Also, the lamination theory is used in conjunction with three failure theories to predict ultimate strengths with varying degrees of success.

Yeow, Y. T.↗
NASA NTRS1976

Axial fatigue of /0, +30, and -30 deg/6s graphite/epoxy

Results are presented for an investigation carried out on a /0, +30, and -30 deg/6s graphite/epoxy angle-ply laminate in order to characterize the overall fatigue behavior, to evaluate strength/moduli degradation due to cyclic loading, and to identify the failure modes and mechanisms. The specimen life determined from fatigue tests is measured as a function of cyclic stress amplitude for various stress ratios. Fractured specimens are sectioned and examined by conventional metallography and SEM to reveal failure modes and mechanisms. It is shown that the laminate studied is susceptible to axial fatigue failures under cyclic loading which involves both tensile and compressive mean stresses. Fracture surface observations indicate the occurrence of complex failure modes. A variety of local failure mechanisms are identified.

Ramani, S. V.↗
NASA NTRS1976

Effect of Low Velocity Impact Damage on the Compressive Strength of Graphite/Epoxy Hat-Stiffened Panels

Low velocity impact damage on the compressive strength of graphite/epoxy hat stiffened panels is studied. Fourteen panels, representative of minimum-mass designs for two compression load levels were tested. Eight panels were damaged by impact and the effect on compressive strength was evaluated by comparing the results with data for undamaged panels. The impact tests consisted of firing 1.27 cm diameter aluminum projectiles normal to the plane of the panel at a velocity of approximately 55 m/sec to simulate impact from runway debris. The results of this investigation indicate that impact damage in the panels designed for 0.53 MN/m was contained locally and the damaged panels were capable of carrying the design load. The panels designed for 1.58 MN/m failed between 50 and 58 percent of the design load due to impact damage in the high axial stiffness region. The extent of damage in the high axial stiffness region of both panel designs increased with the magnitude of applied axial load. Damage in this region was the most significant factor in reducing panel strength. Limited damage that was not visually detectable reduced ultimate strength as much as extensive visible damage.

Rhodes, M. D.↗
NASA NTRS1976

Notched and Unnotched Fatigue Behavior of Angle-Ply Graphite/Epoxy Composites

The axial fatigue behavior of both notched and unnotched graphite/epoxy composites was studied. In unnotched studies, conducted on a 0/+ or - 30 3S AS/3501 laminate, S-N curves were determined for various stress ratios R using simply supported test specimens. Apparent fatigue limits in tension-tension (T-T) and compression-compression (C-C) cycling occurred at about 60% of the respective static strengths. The overall results were expressed in the form of a constant life diagram showing the relationship between mean stress and stress amplitude. The diagram illustrates a skew-symmetry in fatigue life caused by the relatively low compressive strength of the unrestrained test specimens used. In effect, a maximum in fatigue properties occurs at a positive value of mean stress. Results are of significance in situations where structural members are buckling or crippling critical in design.

Ramani, S. V.↗
NASA NTRS1977

A study of damage zones or characteristic lengths as related to the fracture behavior of graphite/epoxy laminates

Uniaxial tensile tests conducted on a variety of graphite/epoxy laminates, containing narrow rectangular slits, square or circular holes with various aspect ratios are discussed. The techniques used to study stable crack or damage zone growth--namely, birefringence coatings, COD gages, and microscopic observations are discussed. Initial and final fracture modes are discussed as well as the effect of notch size and shape, and laminate type on the fracture process. Characteristic lengths are calculated and compared to each other using the point, average and inherent flaw theories. Fracture toughnesses are calculated by the same theories and compared to a boundary integral equation technique. Finite width K-calibration factors are also discussed.

Yeow, Y. T.↗
NASA NTRS1976

Design, fabrication, and test of a full-scale graphite/epoxy metering truss for the space telescope

This paper presents the work performed in a program sponsored by MSFC-NASA in which a full-scale graphite/epoxy metering truss was designed, fabricated and tested. The primary requirement was to provide a structure that was dimensionally stable in a transient temperature environment. Structural element characterization requiring measurements in the microstrain region are described along with resulting strength, stiffness and coefficient of thermal expansion data. The full-scale tests included static, dynamic and thermal-vacuum dimensional stability evaluations.

Oken, S.↗
NASA NTRS1979

Low-cost graphite/epoxy structural panels

Manufacturing process precures components of composite panels prior to assembly. Process separately cures the graphite/epoxy skin, stiffener ribs, and stiffener grid. After curing, panels are assembled using special adhesive. With implementation of cost effective manufacturing techniques, uses of graphite-epoxy laminate panels may be found in other areas such as auto industry.

Lager, J. R.↗
NASA NTRS1978

The time-temperature behavior of a unidirectional graphite/epoxy composite

A testing program to determine the time-temperature response of undirectional graphite/epoxy materials is described. Short-term creep test results of strip tensile specimen with the load at various angles to the fiber direction and at various temperature levels are reported. It was shown that the material is elastic at all temperature levels when the fiber is in the load direction. On the other hand, when the load is transverse to the fibers, the viscoelastic response was shown to vary from small amounts at room temperature to large amounts for temperatures in excess of 180 C for other fiber angles, the response was similar to the latter.

Yeow, Y. T.↗
NASA NTRS1978

Impact behavior of filament wound graphite/epoxy fan blades

The fabrication and impact tests of graphite/epoxy filament wound fan blades are discussed. Blades which were spin tested at tip speeds up to 305 meters per second retained their structural integrity. Two blades were each impacted with a 454 gram slice of a 908 gram simulated bird at a tip speed of 263 meters per second and impact angles of 22 and 32 deg. The impact tests were recorded with high-speed movie film. The blade which was impacted at 22 deg sustained some root delamination but remained intact. The 32 deg impact separated the blade from the root. No local damage other than leading edge debonding was observed for either blade. Results of a failure mode analysis are also discussed.

Bowles, K. J.↗
NASA NTRS1977

An experimental study of the fracture behavior of laminated graphite/epoxy composites

The results of an experimental investigation on the fracture behavior of unidirectional and multidirectional laminated graphite/epoxy composites is reported. Critical tensile fracture stresses for constant head rate uniaxial specimens containing single-edge notches, double-edge notches, and centrally located circular holes are presented. Results are reported for loads and notches at various angles to the fiber direction. Evidence of notch sensitivity and stable crack growth is presented. Self-similar crack growth is shown to occur for only a limited set of circumstances. Critical stresses are compared to the theories of Waddoups et al and Whitney et al. These comparisons are presented using isotropic and orthotropic stress concentration factors together with a finite width correction factor. The results tend to show that use of only isotropic correction factors allow good correlation between theory and experiment.

Brinson, H. F.↗