Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Freestream Velocity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Experimental study of boundary layer transition on a heated flat plate

A detailed investigation to the document momentum and thermal development of boundary layers undergoing natural transition on a heated flat plate was performed. Experimental results of both overall and conditionally sampled characteristics of laminar, transitional, and low Reynolds number turbulent boundary layers are presented. Measurements were done in a low-speed, closed-loop wind tunnel with a freestream velocity of 100 ft/s and zero pressure gradient over a range of freestream turbulence intensities from 0.4 to 6 percent. The distributions of skin friction, heat transfer rate, and Reynolds shear stress were all consistent with previously published data. Reynolds analogy factors for momentum thickness Reynolds number, Re(sub theta) less than 2300 were found to be well predicted by laminar and turbulent correlations which accounted for an unheated starting length and uniform heat flux. A small dependence of turbulence results on the freestream turbulence intensity was observed.

Sohn, K. H.↗
NASA NTRS1991

Analysis of flow on cones and cylinders using discrete vortex methods

Discrete vortex methods have been developed to investigate the vortex flows on cones and two-dimensional cylinders. The cone problem was solved by assuming that, to meet conical flow and zero-force conditions, the vortices move radially away from the body at a given cross-section. The two-dimensional cylinder problem was solved by limiting the velocity along the zero streamline surrounding the vortex field to two times freestream velocity and by limiting the lateral movement of the vortices. Variations in vortex position and strength with time were determined by taking into account the rate at which circulation is generated at separation points on the body. The calculated vortex positions and strengths were in good agreement with available experimental data. Viscous effects could be accounted for by adding empirically determined damping terms to the velocity equations. The models indicate that different types of asymmetry occur for the cone and two-dimensional cylinder. Asymmetry onset boundaries determined by the discrete vortex method show the same trend as experiment.

Gainer, Thomas G.↗
NASA NTRS1991

Experimental study of boundary layer transition on a heated flat plate

A detailed investigation to the document momentum and thermal development of boundary layers undergoing natural transition on a heated flat plate was performed. Experimental results of both overall and conditionally sampled characteristics of laminar, transitional, and low Reynolds number turbulent boundary layers are presented. Measurements were done in a low-speed, closed-loop wind tunnel with a freestream velocity of 100 ft/s and zero pressure gradient over a range of freestream turbulence intensities from 0.4 to 6 percent. The distributions of skin friction, heat transfer rate, and Reynolds shear stress were all consistent with previously published data. Reynolds analogy factors for momentum thickness Reynolds number, Re(sub theta) less than 2300 were found to be well predicted by laminar and turbulent correlations which accounted for an unheated starting length and uniform heat flux. A small dependence of turbulence results on the freestream turbulence intensity was observed.

Sohn, K. H.↗
NASA NTRS1993

Flight validation of a pulsed smoke flow visualization system

A flow visualization scheme, designed to measure vortex fluid dynamics on research aircraft, was validated in flight. Strake vortex trajectories and axial core velocities were determined using pulsed smoke, high-speed video images, and semiautomated image edge detection hardware and software. Smoke was pulsed by using a fast-acting three-way valve. After being redesigned because of repeatedly jamming in flight, the valve shuttle operated flawlessly during the last two tests. A 25-percent scale, Gothic strake was used to generate vortex over the wing of a GA-7 Cougar and was operated at a local angle of attack of 22 degrees and Reynolds number of approximately 7.8 x 10(exp 5)/ft. Maximum axial velocities measured in the vortex core were between 1.75 and 1.95 times the freestream velocity. Analysis of the pulsed smoke system's affect on forebody vortices indicates that the system may reorient the forebody vortex system; however, blowing momentum coefficients normally used will have no appreciable affect on the leading-edge extension vortex system. It is recommended that a similar pulsed smoke system be installed on the F/A-18 High Angle Research Vehicle and that this approach be used to analyze vortex core dynamics during the remainder of its high-angle-of-attack research flights.

Ward, Donald T.↗
NASA NTRSDate not supplied

Integral Velocity Sampling for Unsteady Rotor Models on Cartesian Meshes

An unsteady body-force rotor model utilizing integral velocity sampling is developed for Cartesian meshes with a focus on accurate performance predictions. In this approach, the rotors are modeled as body-force source terms, and integral sampling is used to define the local freestream velocity vector. The method is verified in two dimensions for airfoils, providing accurate angle of attack and freestream Mach number estimates even on relatively coarse meshes, and demonstrating excellent mesh convergence across a variety of source region thicknesses. Extensions of the model to three dimensions for both fixed and rotating wings are considered, with numerical experiments demonstrating the need for a spanwise-continuous representation of the induced velocity or angle of attack. The model provides reasonable spanwise lift distributions without any explicit tip-loss model. Comparisons to high-fidelity simulations and experimental data show excellent agreement for predictions of an isolated DJI Phantom 3 propeller in hover. Finally, simulations of the full aircraft in edgewise forward flight also compare well with wind tunnel data across a variety of pitch angles and propeller speeds.

ARMD↗
NASA NTRS1991

Three-component laser velocimeter surveys of the flow over a backward-facing step

A three-component laser velocimeter is used to investigate the flow over a backward-facing step. The backward-facing step had an expansion ratio of 2, a boundary layer height to step height ratio of 0.34 and a Reynolds number based on step height of 19,000. Results from three-component velocimeter surveys of the flow over the backward-facing step are presented with comparisons of the current experiment with previous experiments and computational results. The present results compared well with previous experiments with the exception of the reattachment length. The short reattachment length was due to the short length of the channel downstream. The measurement of the lateral velocity component showed that there is a mean flow in and out of the centerline plane as high as 7 percent of the freestream velocity. However, the shear stresses show no correlation between the lateral fluctuations and the longitudinal and vertical fluctuations, indicating that the flow is 2D in terms of the turbulence quantities.

Kjelgaard, Scott O.↗
NASA NTRS1974

A forward speed effects study on jet noise from several suppressor nozzles in the NASA/Ames 40- by 80-foot wind tunnel

A test program was conducted in a 40 by 80 foot wind tunnel to evaluate the effect of relative velocity on the jet noise signature of a conical ejector, auxiliary inlet ejector, 32 spokes and 104 tube nozzle with and without an acoustically treated shroud. The freestream velocities in the wind tunnel were varied from 0 to 103.6 m/sec (300 ft/sec) for exhaust jet velocities of 259.1 m/sec (850 ft/sec) to 609.6 m/sec (2000 ft/sec). Reverberation corrections for the wind tunnel were developed and the procedure is explained. In conjunction with wind tunnel testing the nozzles were also evaluated on an outdoor test stand. The wind tunnel microphone arrays were duplicated during the outdoor testing. The data were then extrapolated for comparisons with data measured using a microphone array placed on a 30.5 meter (100 ft) arc. Using these data as a basis, farfield to nearfield arguments are presented with regards to the data measured in the wind tunnel. Finally, comparisons are presented between predictions made using existing methods and the measured data.

Beulke, M. R.↗
NASA NTRS1993

Separated flow generated by a vectored jet in a crossflow

Results of an experimental investigation to determine the characteristics of the separated flow region generated by a subsonic vectored rectangular jet in a subsonic crossflow is presented. Using surface visualization techniques, it was found that the upstream separated flow consist of horseshoe vortices that are formed periodically with a frequency corresponding to that of the vortex shedding behind the jet. The size of the recirculation region around the jet is found to decrease with increasing jet vector angle. The variation of the mean primary separation distance upstream of the jet, with velocity ratio revealed the existence of two different flow regimes. The change from one to the other depends on the velocity ratio and the jet vector angle. It is shown that the Strouhal number, based on the vortex shedding frequency and a combination of jet exit and freestream velocities, varies uniquely with velocity ratio.

Krothapalli, A.↗
NASA NTRSDate not supplied

An Overset Grid Motion Driver for Resolving Entry Vehicle CFD Simulations with Large Changes in Wake Orientation

Time-accurate computational fluid dynamics (CFD) simulations using overset meshes can enable reduced computational cost compared to a rigid, monolithic mesh for blunt-body atmospheric entry vehicles. If the vehicle has a significant change in attitude, the high-density region of the overset mesh designed for resolving the subsonic wake can be kept in position as the wake orientation changes relative to the body. Current simulations generally keep the wake mesh fixed in attitude while the body rotates, assuming the wake orientation remains relatively constant. However, changes in the relative velocity over a long-duration simulation or effects of the body geometry can invalidate this assumption. This work presents a method for calculating the desired mesh orientation to resolve a blunt body wake using the atmosphere-relative velocity of the vehicle. A motion driver using these calculations is implemented in a CFD-in-the-loop flight model bridging the FUN3D flow solver and POST2 trajectory propagator. Overset meshing is performed using the Yoga extension for FUN3D. Results are presented for simulations with both overset and monolithic meshes under large changes in relative velocity (and therefore wake orientation). The results demonstrate that the motion driver successfully orients an overset wake mesh to capture the subsonic wake with sufficient resolution despite variable body rotation and body-relative freestream velocity.

CFD↗
NASA NTRSDate not supplied

An Overset Grid Motion Driver for Resolving Entry Vehicle CFD Simulations with Large Changes in Wake Orientation

Time-accurate computational fluid dynamics (CFD) simulations using overset meshes can enable reduced computational cost compared to a rigid, monolithic mesh for blunt-body atmospheric entry vehicles. If the vehicle has a significant change in attitude, the high-density region of the overset mesh designed for resolving the subsonic wake can be kept in position as the wake orientation changes relative to the body. Current simulations generally keep the wake mesh fixed in attitude while the body rotates, assuming the wake orientation remains relatively constant. However, changes in the relative velocity over a long-duration simulation or effects of the body geometry can invalidate this assumption. This work presents a method for calculating the desired mesh orientation to resolve a blunt body wake using the atmosphere-relative velocity of the vehicle. A motion driver using these calculations is implemented in a CFD-in-the-loop flight model bridging the FUN3D flow solver and POST2 trajectory propagator. Overset meshing is performed using the Yoga extension for FUN3D. Results are presented for simulations with both overset and monolithic meshes under large changes in relative velocity (and therefore wake orientation). The results demonstrate that the motion driver successfully orients an overset wake mesh to capture the subsonic wake with sufficient resolution despite variable body rotation and body-relative freestream velocity.

Computational Fluid Dynamics↗
NASA NTRS1976

Engineering flowfields and heating rates for highly swept wing leading edges

An engineering flow model is developed (and verified experimentally) which describes the flowfield that arises when a supersonic stream encounters a wedge/cylinder configuration whose angles are such that the flow includes only weak shock waves. A numerical code using the perfect gas relations is used to describe the flow in the plane of symmetry inboard of the shock interaction region. Theoretical surface-pressure and heat-transfer distributions are computed for freestream velocities ranging from 1167 to 7610 m/sec. Nondimensionalization of the heat-transfer rates in terms of local flow parameters produced a correlation of Stanton number as a function of the local Reynolds number, which is independent of the freestream flow conditions and of the surface temperature.

Bertin, J. J.↗
NASA NTRS1992

Aerodynamic roughness measured in the field and simulated in a wind tunnel

This study evaluates how well values of aerodynamic surface roughness, z sub 0, measured over scale models in wind tunnels correlate with values of z sub 0 measured at full scale in the field. A field experiment was conducted in which values of z sub 0 and u* (wind friction speed) were measured over three arrays of non-erodible roughness elements on a dry lake bed. Wind profiles were measured by ten anemometers on a 15 m mast under thermally neutral atmospheric conditions. Values of z sub 0 increased from .00014 m (dry lake bed only) to .026 m with increasing roughness element density. The three roughness element arrays were simulated at 1/10 and 1/20 scale in an open-circuit atmospheric boundary-layer wind tunnel. Velocities were measured with a boundary-layer pitot-tube rake from the same relative position within the scale model arrays as the anemometers were relative to the field arrays. Each array at each scale was sampled three times at five freestream velocities. Average values of z sub 0 for each model array at each scale were compared with full-scale values of z sub 0 obtained in the field. The field vs. wind tunnel correspondence of z sub 0 is found to be z sub 0 field = 0.2661 x (z sub(0 model) x scale(exp -1))exp .8159.

Sullivan, Robert↗
NASA NTRS1978

Low speed test of a high-bypass-ratio propulsion system with an asymmetric inlet designed for a tilt-nacelle V/STOL airplane

A large scale model of a lift/cruise fan inlet designed for a tilt nacelle V/STOL airplane was tested with a high bypass ratio turbofan. Testing was conducted at low freestream velocities with inlet angles of attack ranging from 0 deg to 120 deg. The operating limits for the nacelle were found to be related to inlet boundary layer separation. Small separations originating in the inlet diffuser cause little or no performance degradation. However, at sufficiently severe freestream conditions the separation changes abruptly to a lip separation. This change is associated with a significant reduction in nacelle net thrust as well as a sharp increase in fan blade vibratory stresses. Consequently, the onset of lip separation is regarded as the nacelle operating limit. The test verified that the asymmetric inlet design will provide high performance and stable operation at the design forward speed and angle of attack conditions. At some of these, however, operation near the lower end of the design inlet airflow range is not feasible due to the occurrence of lip separation.

Syberg, J.↗
NASA NTRS2015

Investigation of Spiral and Sweeping Holes

Surface infrared thermography, hotwire anemometry, and thermocouple surveys were performed on two new film cooling hole geometries: spiral/rifled holes and fluidic sweeping holes. The spiral holes attempt to induce large-scale vorticity to the film cooling jet as it exits the hole to prevent the formation of the kidney shaped vortices commonly associated with film cooling jets. The fluidic sweeping hole uses a passive in-hole geometry to induce jet sweeping at frequencies that scale with blowing ratios. The spiral hole performance is compared to that of round holes with and without compound angles. The fluidic hole is of the diffusion class of holes and is therefore compared to a 777 hole and Square holes. A patent-pending spiral hole design showed the highest potential of the non-diffusion type hole configurations. Velocity contours and flow temperature were acquired at discreet cross-sections of the downstream flow field. The passive fluidic sweeping hole shows the most uniform cooling distribution but suffers from low span-averaged effectiveness levels due to enhanced mixing. The data was taken at a Reynolds number of 11,000 based on hole diameter and freestream velocity. Infrared thermography was taken for blowing rations of 1.0, 1.5, 2.0, and 2.5 at a density ration of 1.05. The flow inside the fluidic sweeping hole was studied using 3D unsteady RANS.

infrared thermography↗
NASA NTRS2018

Toward Cooling Uniformity: Investigation of Spiral, Sweeping Holes, and Unconventional Cooling Paradigms

Surface infrared thermography, hotwire anemometry, and thermocouple surveys were performed on two new film cooling hole geometries: spiral/rifled holes and fluidic sweeping holes. Ways to quantify the efficacy of novel cooling holes that are asymmetric, not uniformly spaced or that show variation from hole to hole are presented. The spiral holes attempt to induce large-scale vorticity to the film cooling jet as it exits the hole to prevent the formation of the kidney shaped vortices commonly associated with film cooling jets. The fluidic sweeping hole uses a passive in-hole geometry to induce jet sweeping at frequencies that scale with blowing ratios. The spiral hole performance is compared to that of round holes with and without compound angles. The fluidic hole is of the diffusion class of holes and is therefore compared to a 777 hole and square holes. A patent-pending spiral hole design showed the highest potential of the nondiffusion type hole configurations. Velocity contours and flow temperature were acquired at discreet cross-sections of the downstream flow field. The passive fluidic sweeping hole shows the most uniform cooling distribution but suffers from low span-averaged effectiveness levels due to enhanced mixing. The data was taken at a Reynolds number of 11,000 based on hole diameter and freestream velocity. Infrared thermography was taken for blowing ratios of 1.0, 1.5, 2.0, and 2.5 at a density ratio of 1.05. The flow inside the fluidic sweeping hole was studied using 3D unsteady RANS. A section on ideas for future work is included that addresses issues of quantifying cooling uniformity and provides some ideas for changing the way we think about cooling such as changing the direction of cooling or coupling acoustic devices to cooling holes to regulate frequency.

Shyam, Vikram↗
NASA NTRS2019

Implementation of a Pulsed-Laser Measurement System in the National Transonic Facility

A remotely-adjustable laser transmission and imaging system has been developed for use in a high-pressure, cryogenic wind tunnel. Implementation in the National Transonic Facility has proven the system suitable for velocity and signal lifetime measurements over a range of operating conditions. The measurement system allows for the delivery of high-powered laser pulses through the outer pressure shell and into the test section interior from a mezzanine where the laser is free from environmental disturbances (such as vibrations and excessive condensation) associated with operation of the wind tunnel. Femtosecond laser electronic excitation tagging (FLEET) was utilized to provide freestream velocity measurements, and first results show typical data that may be obtained using the system herein described.

Reese, Daniel T.↗
NASA NTRS1991

Propulsion-induced aerodynamics of an ejector-configured STOVL fighter aircraft

Propulsion-induced aerodynamic effects are computed by using data obtained from tests of a full-scale model of the E-7A configuration that were run in the NASA Ames 40 x 80 and 80 x 120-foot tunnels. These effects are shown both in aerodynamic coefficients and nondimensionalized by thrust versus equivalent velocity. The test results show that the full-scale ventral nozzle-induced effects are smaller than scale model data, while the ejector-induced effects demonstrate fair agreement. The effect of tunnel test section size is primarily observed at low and static speed, high thrust conditions, as seen in comparisons of data from both tunnels. The 80 x 120-foot tunnel test gave better static thrust calibrations and permitted a greater range of test freestream velocities and angles-of-attack, extending the database provided by the full-scale model.

Poppen, William A.↗
NASA NTRS1982

Turbulent boundary layer over solid and porous surfaces with small roughness

The wind tunnel models and instrumentation used as well as data reduction and error analysis techniques employed are described for an experimental study conducted to measure directly skin friction and obtain profiles of mean velocity, axial and normal turbulence intensity, and Reynolds stress in the untripped boundary on a large diameter axisymmetric body. Results are given for such a body with a (1) smooth, solid surface; (2) a sandpaper roughened, solid surface; (3) a sintered metal, porous surface; (4) a ""smooth'' performated titanium surface; (5) a rough, solid surface made of fine diffusion bonded screening; and (6) a rough, porous surface made of the same screening. The roughness values were in low range (k+ 5 to 7) just above what is normally considered ""hydraulically smooth''. Measurements were taken at several axial locations and tow or normal stream freestream velocities, 45.1 m/sec and 53.5 m/sec.

Kong, F. Y.↗