Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FORGE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

The Determination of Residual Stress in Quenched and Cold-Compressed 7050 Aluminum Alloy T-Section Forgings by the Contour Method and Neutron Diffraction

Residual stresses were determined through the thickness of quenched and quenched followed by cold compression 7050 aluminum alloy T-section forgings using the contour method and neutron diffraction. 7050 T-section forgings are used for the manufacture of the connecting joints of wing and fuselage. Inevitably high residual stresses are introduced during the quenching process of 7050 T-section forgings, which could be reduced by cold compression to overcome the effect of residual stress on machining deformation. The longitudinal residual stresses obtained by the two techniques achieved good agreement in both trend and magnitude in both the quenched and quenched followed by cold compression 7050 T-section forgings. The stress-free lattice spacing of Al(311), the Bragg reflection used for the neutron measurements, was obtained from a 5-mm slice using the plane-stress condition, and its variation through the thickness is insignificant in both the quenched specimen and quenched followed by cold compression specimen. A comparison of the residual stresses in the quenched specimen and quenched followed by cold compression specimen showed significant changes in range of residual stresses from (− 304, 262 MPa) induced by quenching process to (− 125, 142 MPa) due to 3% cold compression. The percentage reduction in residual stress in the quenched specimen due to 3% cold compression was (46, 59%).

36 MATERIALS SCIENCE↗

Research into Oil-based Colloidal-Graphite Lubricants for Forging of Al-based Alloys

The presented paper describes the topical problem in metal forging production. It deals with the choice of an optimal lubricant for forging of Al-based alloys. Within the scope of the paper, the properties of several oil-based colloidal-graphite lubricants were investigated. The physicochemical and technological properties of these lubricants are presented. It was found that physicochemical properties of lubricant compositions have an influence on friction coefficient value and quality of forgings.The ring compression method was used to estimate the friction coefficient value. Hydraulic press was used for the test. The comparative analysis of the investigated lubricants was carried out. The forging quality was estimated on the basis of production test. The practical recommendations were given to choose an optimal oil-based colloidal-graphite lubricant for isothermal forging of Al-based alloy.

36 MATERIALS SCIENCE↗

2017 Status report-Tritium aging studies on stainless steel: Effect of hydrogen, tritium and decay helium on the fracture-toughness properties of stem, cup and block forgings

The materials of construction of tritium reservoirs are forged stainless steels. During service, the structural properties of the stainless steel change over time because of the diffusion of tritium into the reservoir wall and its radioactive decay to helium-3. This aging effect can cause cracks to initiate and grow which could result in a tritium leak or delayed failure of a tritium reservoir. Numerous factors affect the tendency for crack formation and propagation and are being investigated in this program. The goal of the research is to provide relevant fracture mechanics data that can be used by the design agencies in their assessments of tritium reservoir structural integrity. In this status report, new experimental results are presented on the effects of tritium and decay helium on the cracking properties of specimens taken from actual tritium reservoir forgings instead of the experimental forgings of past programs. The properties measured are more representative of actual reservoir properties because the microstructure of the specimens tested are more like that of the actual tritium reservoirs. The program was designed to measure the effects of material variables on tritium compatibility and includes two stainless steels (Type 304L and 316L stainless steel), multiple yield strengths (360-500 MPa), and multiple forging shapes (Stem, Cup, and Block).

36 MATERIALS SCIENCE↗

Utah FORGE: 3D Gravity Data

These resources describe the 3D geophysical inversion modeling of gravity data at the FORGE site near Milford, Utah. FORGE is the Frontier Observatory for Research in Geothermal Energy and the site in Utah has been selected by the U.S. Dept. of Energy for a 5-year R&D program to test technologies for the development of Engineered Geothermal Systems (EGS). 3D modelling of gravity data at the FORGE site is to help characterize the subsurface geologic framework. Specifically, modelling of gravity data in 3D, used in conjunction with rock density measurements and other subsurface geologic information can provide an independent test of an existing 3D geologic model (e.g. Witter et al., 2018). Such an exercise can be useful for reducing uncertainty in 3D geologic models (Witter et al, 2019).

15 GEOTHERMAL ENERGY↗

Utah FORGE Well 16A(78)-32 Stimulation DFN Fracture Plane Evaluation and Data

This dataset includes files used to fit planar fractures through the preliminary earthquake catalogs of the three stages of the April 2022 well 16A(78)-32 stimulation which is linked bellow. These planar features have been used to update the FORGE reference Discrete Fracture Network (DFN) model. The files are provided to encourage other modelers to use additional workflows to find additional/alternative features. To this end, the dataset includes the cleaned earthquake catalog data translated to the FORGE reference model global reference frame, the well trajectory of 16A(78)-32 in those same coordinates, the fit 15 planar features in csv format, and a pdf file with slides illustrating the process used to fit the features. A recorded presentation of this material is available from the October 2022 FORGE Modeling and Simulation Forum which is also linked below.

15 GEOTHERMAL ENERGY↗

Utah FORGE: Well 16B(78)-32 Drilling Data

This drilling data for Utah FORGE well 16B(78)-32 include a well survey, core summary, mud and mud temperature logs, daily reports of the drilling process, and additional data from the Pason oil and gas company. Well 16B(78)-32 serves as the production well for reservoir creation, fluid circulation, and demonstration of heat extraction for the FORGE project. It has been drilled as a doublet approximately 300 feet parallel to and above the injection well 16A(78)-32. The proposed total depth was 10,658 feet, which was exceeded. Spudding began on April 26th, 2023. As of June 20th, 2023, the total depth measured 10,947 feet and the vertical depth measured 8,357 feet. Drilling included the trial use of insulated drill pipe (IDP) from Eavor Technologies, which was considered a success. IDP restricts counter-current heat transfer between drilling fluid inside the drill string and hotter returning fluid in the annulus, thereby ensuring the bottomhole assembly (BHA) remains submerged in cool fluid. Eavor rented 350 joints of IDP to FORGE which were run in two consecutive BHAs at the well. The results of this trial are included here.

15 GEOTHERMAL ENERGY↗

Pulse current auxiliary forging of sintered TiAl alloys based on the investigation of dynamic recrystallization and phase transformation

Highlights: • DRX kinetics model of sintered near γ TiAl alloy was established. • DRX process was accompanied by twinning when compressed at 1125 °C/0.1 s{sup − 1}. • Hot deformation has a promotion to the phase transformation of γ → α. - Abstract: Pulse current auxiliary forging is a new and efficient way to fabricate high performance TiAl based alloys. Dynamic recrystallization (DRX) and phase transformation have a pronounced effect on the subsequent deformability of TiAl based alloys. Hence, the dynamic recrystallization kinetics were determined at the temperature range of 1125–1275 °C and strain rate range of 0.1–0.001 s{sup − 1}. In addition, the DRX mechanism and phase transformation of TiAl based alloys were investigated to model the microstructure evolution in order to provide guidance for the pulse current auxiliary forging process. When the specimens were compressed at 1125 °C/0.1 s{sup − 1}, twinning played an important role in the DRX process. With increasing deformation temperature, the microstructure transformed from near gamma into duplex microstructure. In addition, according to the kinetics of dynamic recrystallization and phase transformation, fully DRXed TiAl based alloys were fabricated through pulse current auxiliary forging. The as-forged TiAl-based alloys show good superplastic performance with an elongation over 410%.

36 MATERIALS SCIENCE↗

Effect of whisker breakage on the forgeability and the tensile properties of the forged 2024Al/Al18B4O33w composite

Highlights: • The rotation and breakage of whiskers and microcracks contribute to strain softening during compression. • The whiskers with orientation angle of about 45° to the applied axial stress are serious broken. • The microcracks between the broken whiskers connecting with others result in major surface crack. • The composite forged at 450 °C and at strain rate of 0.1 s{sup − 1} shows no major surface cracks and the increase in the elongation, yield strength and tensile strength. - Abstract: The effect of the whisker breakage on the forgeability of 2024Al/Al{sub 18}B{sub 4}O{sub 33}w composite is investigated. The 2024Al/Al{sub 18}B{sub 4}O{sub 33}w composite is forged according to the forgeability at the different temperatures. The tensile properties of the as-cast and forged composites are also studied. The results shows that the rotation and breakage of the whiskers and the microcracks contribute to the strain softening during compression. The whiskers with the orientation angle of about 45° to the applied axial stress are serious broken resulting in the lower average aspect ratio of the whiskers. Due to the lower flow ability of the matrix at the lower temperature than 400 °C, the microcracks between the broken whiskers connecting with others result in the major surface crack oriented to approximately 45° with respect to the compression direction. The composite forged at the temperature of 450 °C and at the strain rate of 0.1 s{sup − 1} shows the no major surface cracks and the increase in the elongation, yield strength and tensile strength.

36 MATERIALS SCIENCE↗

Accumulative fold-forging (AFF) as a novel severe plastic deformation process to fabricate a high strength ultra-fine grained layered aluminum alloy structure

Highlights: • A novel SPD process named as AFF was introduced. • AFF process is based on the repetitive forging of folded metal foils. • This new method possesses an exceptional capability for fabrication of UFG layered structures. • An AA8006 aluminum alloy layered material with the UFG structure of 200–300 nm was produced. • An enhanced hardness up to ~ 100% was attained owing to the UFG and layered structures. - Abstract: A novel severe plastic deformation (SPD) process termed accumulative fold forging (AFF) is introduced to fabricate a homogenous ultra-fine grained (UFG) layered metal structure by repetitive folding and forging aluminum alloy foil. The present work studies AFF applied to thin foils of AA8006 Al-Fe-Mn aluminum alloy after 26 folding steps to produce a UFG structure containing 67,108,864 layers across a 2 mm thickness. The structure of the layers and grain refinement are studied using X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM) and scanning-transmission electron microscopy (STEM) analysis. The results indicate a well-bonded inter-layer structure with an average grain size of about 200 nm parallel and 250 nm perpendicular to the forging direction, while dislocation density increased to ~ 7.2 × 10{sup 15} m{sup − 2} following AFF. The mechanical strength of the aluminum foil is evaluated in the terms of indentation hardness testing before and after AFF process. The processed UFGed layered material exhibited an average hardness value of ~ 61.5 Vickers as compared to the initial value of ~ 30.4 Vickers for the annealed foil alloy, which indicates an improvement of ~ 100% due to the contributions of grain refinement, work hardening and interfacial strengthening of the bonded layers.

36 MATERIALS SCIENCE↗

Anisotropy of the Thermal Expansion of a Polycrystalline Ni–Mn–Ga Alloy Subjected to Plastic Deformation by Forging

The formation of a sharp crystallographic texture in a Ni–Mn–Ga Heusler alloy by the multiple isothermal forging has been studied. An analysis of the thermal expansion near the martensitic transformation temperatures in the as-cast and forged states of the alloy shows that the thermomechanical treatment leads to an increase in the anisotropy of the sample geometric size changing during the phase transformation, which favors an increase in the functional characteristics of the alloy. The structural studies show that the alloy structure after multiple isothermal forging has the bimodal distribution of grain sizes. The formation of the bimodal structure by forging is assumed to make it possible to enhance the stability of the functional properties of the alloy during repeated cycles of the phase transformation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Analysis of Rig Parameter Data Using Drilling Process Modeling Constraints, Volume 5: Utah FORGE Well 16B(78)-32

Drill rig parameter measurements are routinely used during deep well construction to monitor and guide drilling conditions for improved performance and reduced costs. While insightful into the drilling process, these measurements are of reduced value without a standard to aid in data evaluation and decision making. In the main body of this work (Volume 1), a method is demonstrated whereby rock reduction model constraints are used to interpret drilling response parameters; the method could be applied in real-time to improve decision-making in the field and to further discern technology performance during post-drilling evaluations. Drilling parameters are evaluated using laboratory-validated rock reduction models for predicting the phenomenological response of drag bits (Detournay and Defourny, 1992) in computational algorithms. The method presented has applicability to development of advanced analytics on future geothermal wells using real-time electronic data recording for improved performance and reduced drilling costs. A drilling cost model is also used to show the tradeoff between rate of penetration and bit life and the influence on interval drilling costs. Details of the bit specifications and performance are cataloged in an independent volume, documented under separate cover, for each of the four wells, and include Volume 2: Utah FORGE 16A(78)-32; Volume 3: Utah FORGE 56-32; Volume 4: Utah FORGE 78B-32 and Volume 5: Utah FORGE 16B(78)-32.

15 GEOTHERMAL ENERGY↗

Analysis of Rig Parameter Data Using Drilling Process Modeling Constraints, Volume 4: Utah FORGE Well 78B-32

Drill rig parameter measurements are routinely used during deep well construction to monitor and guide drilling conditions for improved performance and reduced costs. While insightful into the drilling process, these measurements are of reduced value without a standard to aid in data evaluation and decision making. In the main body of this work (Volume 1), a method is demonstrated whereby rock reduction model constraints are used to interpret drilling response parameters; the method could be applied in real-time to improve decision-making in the field and to further discern technology performance during post-drilling evaluations. Drilling parameters are evaluated using laboratory-validated rock reduction models for predicting the phenomenological response of drag bits (Detournay and Defourny, 1992) in computational algorithms. The method presented has applicability to development of advanced analytics on future geothermal wells using real-time electronic data recording for improved performance and reduced drilling costs. A drilling cost model is also used to show the tradeoff between rate of penetration and bit life and the influence on interval drilling costs. Details of the bit specifications and performance are cataloged in an independent volume, documented under separate cover, for each of the four wells, and include Volume 2: Utah FORGE 16A(78)-32; Volume 3: Utah FORGE 56-32; Volume 4: Utah FORGE 78B-32 and Volume 5: Utah FORGE 16B(78)-32.

15 GEOTHERMAL ENERGY↗

Analysis of Rig Parameter Data Using Drilling Process Modeling Constraints, Volume 3: Utah FORGE Well 56-32

Drill rig parameter measurements are routinely used during deep well construction to monitor and guide drilling conditions for improved performance and reduced costs. While insightful into the drilling process, these measurements are of reduced value without a standard to aid in data evaluation and decision making. In the main body of this work (Volume 1), a method is demonstrated whereby rock reduction model constraints are used to interpret drilling response parameters; the method could be applied in real-time to improve decision-making in the field and to further discern technology performance during post-drilling evaluations. Drilling parameters are evaluated using laboratory-validated rock reduction models for predicting the phenomenological response of drag bits (Detournay and Defourny, 1992) in computational algorithms. The method presented has applicability to development of advanced analytics on future geothermal wells using real-time electronic data recording for improved performance and reduced drilling costs. A drilling cost model is also used to show the tradeoff between rate of penetration and bit life and the influence on interval drilling costs. Details of the bit specifications and performance are cataloged in an independent volume, documented under separate cover, for each of the four wells, and include Volume 2: Utah FORGE 16A(78)-32; Volume 3: Utah FORGE 56-32; Volume 4: Utah FORGE 78B-32 and Volume 5: Utah FORGE 16B(78)-32.

15 GEOTHERMAL ENERGY↗

Analysis of Rig Parameter Data Using Drilling Process Modeling Constraints, Volume 1: Summary of Utah FORGE Wells 16A(78)-32, 56-32, 78B-32 and 16B(78)-32

Drill rig parameter measurements are routinely used during deep well construction to monitor and guide drilling conditions for improved performance and reduced costs. While insightful into the drilling process, these measurements are of reduced value without a standard to aid in data evaluation and decision making. In the main body of this work (Volume 1), a method is demonstrated whereby rock reduction model constraints are used to interpret drilling response parameters; the method could be applied in real-time to improve decision-making in the field and to further discern technology performance during post-drilling evaluations. Drilling parameters are evaluated using laboratory-validated rock reduction models for predicting the phenomenological response of drag bits (Detournay and Defourny, 1992) in computational algorithms. The method presented has applicability to development of advanced analytics on future geothermal wells using real-time electronic data recording for improved performance and reduced drilling costs. A drilling cost model is also used to show the tradeoff between rate of penetration and bit life and the influence on interval drilling costs. Details of the bit specifications and performance are cataloged in an independent volume, documented under separate cover, for each of the four wells, and include Volume 2: Utah FORGE 16A(78)-32; Volume 3: Utah FORGE 56-32; Volume 4: Utah FORGE 78B-32 and Volume 5: Utah FORGE 16B(78)-32.

15 GEOTHERMAL ENERGY↗

Residual Stresses in 21-6-9 Stainless Steel Warm Forgings

Forging residual stresses are detrimental to the production and performance of derived machined parts due to machining distortions, corrosion drivers and fatigue crack drivers. Residual strains in a 21-6-9 stainless steel warm High Energy Rate Forging (HERF) were measured via neutron diffraction. The finite element analysis (FEA) method was used to predict the residual stresses that occur during forging and water quenching. The experimentally measured residual strains were used to calibrate simulations of the three-dimensional residual stress state of the forging. ABAQUS simulation tools predicted residual strains that tend to match with experimental results when varying yield strength is considered.

Everhart, Wesley A.↗

Shock Hugoniot of forged and additively manufactured 304L stainless steel

The purpose of this research was to measure the equation of state for additively manufactured (AM) and forged 304L stainless steel. An understanding of the dynamic behavior of AM metals is integral to their timely adoption into industrial and governmental applications. The Hugoniot of the AM 304L was compared to that of the forged 304L. This comparison enabled us to determine the sensitivity of the equation of state to processing parameters and the resulting microstructure. Our results show that there is a measurable difference in the Hugoniot between the AM 304L and forged 304L. The shock wave velocities for the AM 304L were found to be slower than those for the forged 304L at similar particle speeds perhaps because of the presence of porosity in the AM 304L. While our measurements of density showed no distinct trend toward a measurable decrease in density in the AM 304L, there was a fair amount of scatter in these results.

36 MATERIALS SCIENCE↗

TRITIUM AGING EFFECTS ON THE FRACTURE TOUGHNESS PROPERTIES OF FORGED STAINLESS STEEL

The fracture toughness properties of Type 21-6-9 stainless steel were measured for forgings in the unexposed, hydrogen-exposed, and tritium-exposed-and-aged conditions. Fracture toughness samples were cut from conventionally-forged and high-energy-rate-forged forward-extruded cylinders and mechanically tested at room temperature using ASTM fracture-toughness testing procedures. Some of the samples were exposed to either hydrogen or tritium gas (340 MPa, 623 K) prior to testing. Tritium-exposed samples were aged for up to seven years and tested periodically in order to measure the effect on fracture toughness of {sup 3}He from radioactive tritium decay. The results show that hydrogen-exposed and tritium-exposed samples had lower fracture- toughness values than unexposed samples and that fracture toughness decreased with increasing decay {sup 3}He content. Forged steels were more resistant to the embrittling effects of tritium and decay {sup 3}He than annealed steels, although their fracture-toughness properties depended on the degree of sensitization that occurred during processing. The fracture process was dominated by microvoid nucleation, growth and coalescence; however, the size and spacing of microvoids on the fracture surfaces were affected by hydrogen and tritium with the lowest-toughness samples having the smallest microvoids and finest spacing.

08 HYDROGEN↗