Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Equivalent”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Experimental Investigation of Air-Fuel Equivalence Ratio Effects on Advanced Dual-fuel Diesel/Ammonia Combustion on a Single-Cylinder Medium-Duty Diesel Engine at High Load

Ammonia (NH3) has gathered a lot of interest as a low-lifecycle-carbon fuel in sectors with high weight and distance requirements, such as shipping. The International Maritime Organization (IMO) mandates a 70-80% greenhouse gas (GHG) reduction by 2040, which is only possible with advanced engine technologies and fuels like NH3. Prior research studies at the US Department of Energy’s Oak Ridge National Laboratory have shown strong performance with NH3 under dual-fuel mode using conventional diesel combustion (CDC) manifold air pressure (MAP) settings. Diesel airflow was initially used to simplify retrofitting (no turbocharger modification), which resulted in air-fuel equivalence ratios (λ) greater than 1.5. To characterize potential improvements in dual-fuel NH3 combustion performance at richer in-cylinder conditions, a global λ sweep using a diesel pilot ignition (DPI) strategy with diesel fuel injected near top-dead center (TDC) and a reactivity-controlled compression ignition (RCCI) injection strategy with diesel fuel injected earlier during the compression stroke were compared. The experiments were conducted at 1200 RPM and 12.6 bar (75% load), and λ was varied by decreasing the commanded air flow to the engine at greater than 90% ammonia energy substitution (AES) level. A diesel injection timing sweep was conducted for both the combustion modes at fixed λ, and the timing with the lowest engine-out N2O emissions was identified. The results indicated an optimal balance between CO2, eq and thermal efficiency benefits for both DPI and RCCI injection strategy cases compared to CDC at a λ of 1.4. The indicated N-based emissions exhibited a strong correlation to the ratio of CA5–50 and ignition delay for DPI, but no apparent trend emerged for the RCCI injection strategy at the tested boundary conditions.

Tyrewala, Daanish [ORNL] (ORCID:0000000208599324)↗
DOE OSTI2026

Stochastic fracture generation and thermo-hydro-mechanical modeling in an equivalent continuum framework for enhanced geothermal systems

Enhanced geothermal systems (EGS) involve fracturing low permeability material to establish well connectivity and then injecting and circulating fluid into the fractured subsurface for geothermal power production. Changes in fracture aperture from contraction of the cooling matrix rock may alter network connectivity and risk thermal short-circuiting. Thermo-hydro-mechanical (THM) models are a useful tool to study these processes. However, as fracture networks are complex, and data may be limited, fracture networks in THM models are often stochastically generated. Given reliance on stochastic fracture networks and THM modeling to represent the subsurface and assess productivity of EGS, increased understanding of the influence of such statistically derived fracture networks on flow and heat transport in THM models is needed. Here, a new fracture process model is developed in the reactive transport code PFLOTRAN to stochastically generate fracture families and simulate changes in fracture aperture over time due to temperature changes of the rock matrix. Sixty-four different fracture networks ranging from well to poorly-connected, are modeled in PFLOTRAN with and without mechanical processes (THM vs TH). Results indicate that for well-connected fracture networks, thermal short-circuiting is less of a concern due to the abundance of available alternative flowpaths. For poorly-connected fracture networks, inclusion of mechanical processes showed steep thermal drawdown coincident with increase in fracture aperture along developing colder flowpaths, demonstrating the risk of thermal short-circuiting. Simulations with additional, larger fractures engineered to establish connectivity in a poorly-fractured subsurface, indicate that while stochastic variation of fracture orientation of the background network had limited influence, such variation in the engineered fractures significantly affected flow and heat transport.

Discrete fracture networks (DFN)↗
DOE OSTI2024

A Goldstone boson equivalence for inflation

The effective field theory of single-field inflation characterizes the inflationary epoch in terms of a pattern of symmetry breaking. An operator acquires a time-dependent vacuum expectation value, defining a preferred spatial slicing. In the absence of dynamical gravity, the fluctuations around the time-dependent background are described by the Goldstone boson associated with this symmetry breaking process. With gravity, the Goldstone is eaten by the metric, becoming the scalar metric fluctuation. In this paper, we will show that in general single-field inflation, the statistics of scalar metric fluctuations are given by the statistics of this Goldstone boson decoupled from gravity up to corrections that are controlled as an expansion in slow-roll parameters. This even holds in the presence of additional parameters, like the speed of sound, that naively enhance the impact of the gravitational terms. In the process, we derive expressions for leading and sub-leading gravitational corrections to all-orders in the Goldstone boson.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Structural response reconstruction using a system-equivalent singular vector basis

Here, this paper develops a novel method for reconstructing the full-field response of structural dynamic systems using sparse measurements. The singular value decomposition is applied to a frequency response matrix relating the structural response to physical loads, base motion, or modal loads. The left singular vectors form a non-physical reduced basis that can be used for response reconstruction with far fewer sensors than existing methods. The contributions of the singular vectors to measured response are termed singular-vector loads (SVLs) and are used in a regularized Bayesian framework to generate full-field response estimates and confidence intervals. The reconstruction framework is applicable to the estimation of single data records and power spectral densities from multiple records. Reconstruction is successfully performed in configurations where the number of SVLs to identify is less than, equal to, and greater than the number of sensors used for reconstruction. In a simulation featuring a seismically excited shear structure, SVL reconstruction significantly outperforms modal FRF-based reconstruction and successfully estimates full-field responses with as few as two uniaxial accelerometers. SVL reconstruction is further verified in a simulation featuring an acoustically excited cylinder. Finally, response reconstruction and uncertainty quantification are performed on an experimental structure with three shaker inputs and 27 triaxial accelerometer outputs.

42 ENGINEERING↗
DOE OSTI2025

Ptychographic reconstructions performed in real time and offline have equivalent quality

Abstract Ptychography is a burgeoning imaging technique that enables high-resolution, lensless reconstruction of complex samples by analysing overlapping diffraction patterns, making it invaluable in fields like materials science, biology, and nanotechnology. Real-time ptychographic reconstructions are gaining interest in the scientific community as they provide immediate feedback. Yet their potential to replace offline reconstructions remains uncertain, in part due to questions about the quality of the resulting images. This study quantitatively compares real-time and offline reconstructions at different overlap conditions. Offline reconstructions, using all diffraction patterns at once, and real-time reconstructions, where new frames are added to the reconstructions in small chunks as the diffraction patterns are recorded, were indistinguishable and identical in reconstruction quality. These results hold consistently across all tested overlap ratios. This study represents the first quantitative analysis of real-time ptychographic reconstruction using a growing dataset, demonstrating the potential for real-time reconstructions to replace or at least complement offline reconstructions.

Science & Technology - Other Topics↗
DOE OSTI2026

Are Capacity and Energy Loss Equivalent Metrics for Battery Aging Reporting?

Battery aging in research publications and manufacturer specification sheets for individual cells is commonly reported as capacity (Ah) versus cycle number. However, the key measured quantity in battery-powered devices is energy (Wh), which is derived from integrating capacity with voltage. In this work, we compare the rate of capacity and energy loss across a wide range of Li-ion single-cell cycling studies with different positive electrode chemistries, charge–discharge rates, and temperatures. We find that the relative rate of discharge energy loss varies with cycling conditions. For many cells cycled under moderate conditions, the rate of discharge energy fade is only slightly faster than the rate of discharge capacity fade. However, some cells demonstrated up to a 15% decline in cycle count when 80% energy retention rather than 80% capacity retention was used as the end-of-life metric. These results highlight the importance of reporting cell aging based on energy fade to avoid overestimating battery lifetime in full systems.

batteries↗
DOE OSTI2025

$2+1$ dimensional Floquet systems and lattice fermions: Exact bulk spectral equivalence

A connection has recently been proposed between periodically driven systems known as Floquet insulators in continuous time and static fermion theories in discrete time. This connection has been established in a (1+1) ( 1 + 1 ) -dimensional free theory, where an explicit mapping between the spectra of a Floquet insulator and a discrete-time Dirac fermion theory has been formulated. Here we investigate the potential of static discrete-time theories to capture Floquet physics in higher dimensions, where so-called anomalous Floquet topological insulators can emerge that feature chiral edge states despite having bulk bands with zero Chern number. Starting from a particular model of an anomalous Floquet system, we provide an example of a static discrete-time theory whose bulk spectrum is an exact analytic match for the Floquet spectrum. The spectra with open boundary conditions in a particular strip geometry also match up to finite-size corrections. However, the models differ in several important respects. The discrete-time theory is spatially anisotropic, so that the spectra do not agree for all lattice terminations, e.g. other strip geometries or on half spaces. This difference can be attributed to the fact that the static discrete-time model is quasi-one-dimensional in nature and therefore has a different bulk-boundary correspondence than the Floquet model.

Iadecola, Thomas (ORCID:0000000251456441)↗
DOE OSTI2024

Equivalency Factors and Mixed Isotope Subcritical Limits in H-Canyon [Slides]

Accurate references and documentation are of upmost importance, especially with the current workforce makeup. Tribal knowledge is likely to be lost with turnover. Using a questioning attitude is a great way to find gaps in existing analysis and “normal practices.” Most of the references reviewed are from the 1970’s, with the most recent authored in 1994. Many of these references have been revised and/or superseded in the years since. Though safe, many of the values are likely overconservative, as improvements with modeling and additional critical experiments have been performed in the years since. It would be prudent to reevaluate, clarify, and simplify the values used in H-Canyon.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Report on the Integration of Experimental and Modeling Data for Initial Equivalence Study of Microstructural Evolution in Irradiated LPBF 316SS

Advanced materials and manufacturing technologies are poised to improve the safety and design characteristics of nuclear technologies and meet US energy, environmental, and economic needs. In particular, metal additive manufacturing (AM) provides an opportunity to produce novel materials and component geometries, but their use is not without hurdles arising from the inherent microstructure variability that can result from the layer-by-layer build approach. Given the greater possible microstructure variability in AM materials—and the dearth of materials test reactors—it is impractical to rely solely on neutron irradiation studies to produce data for materials qualification for every possibility. This work within the Advanced Materials and Manufacturing Technologies (AMMT) Environmental Effects technical area contributes to the rapid qualification framework by developing a science-driven framework for the accelerated qualification of materials for nuclear environments. A key product of the Environmental Effects technical area of the AMMT program is the Licensing Approach with Ions and Neutrons (LAIN). This approach recognizes that whether using existing materials in new environments, newly developed materials tailored for these environments, or new manufacturing methods, the traditional decades-long approach for materials qualification does not facilitate rapid deployment. In FY 2023, the AMMT program presented a conceptual framework of specific steps to fulfill several technical challenges associated with qualifying materials for performance in radiation environments on an accelerated time frame informed by the state of the art in materials science and a review of the current regulatory landscape. The objective of this section of the Environmental Effects technical area is to critically evaluate and refine the proposed qualification framework presented under AMMT by integrating the research results of the neutron irradiations, the ion irradiations, and modeling efforts. These ongoing efforts span across Argonne National Laboratory (ANL), Idaho National Laboratory (INL), and Oak Ridge National Laboratory (ORNL) and are closely coordinated.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Vitrification of Hanford Tank 241-AN-107 Waste and Equivalent Simulant

Hanford Site nuclear waste is to be vitrified at the Waste Treatment and Immobilization Plant (WTP), which is a part of the safe and efficient retrieval, treatment, and disposal mission of the U.S. Department of Energy Office of River Protection. Hanford tank 241-AN-107 (referred to herein as AN-107) is one of the initial Hanford radioactive tank wastes planned to be processed and vitrified. A portion of AN-107 waste was retrieved by Washington River Protection Solutions, LLC (WRPS) and transferred to Pacific Northwest National Laboratory (PNNL). Compared to previously received and vitrified wastes (AP-107, AP-105, and AP-105), the concentration of organics in AN-107 was greater by an order of magnitude, while the activity of radionuclides was multiple orders of magnitude greater.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

GridLAB-D Technical Support Document: Residential Equivalent Thermal Parameter Model

GridLAB-D is a power distribution systems simulation and analysis tool developed by Pacific Northwest National Laboratory. Although GridLAB-D and its underlying residential load model has been used in a variety of power systems analyses, comprehensive documentation of the derivation of the residential house model has not been formally published. The purpose of this technical support document is to serve as a comprehensive resource for the thermal dynamics modeling and house definition implemented in GridLAB-D. It covers model derivation, parameter definitions, and implementation steps in the codebase.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2025

Vitrification of Hanford Tank 241-AW-105 Waste and Equivalent Simulant

Hanford Site nuclear waste is to be vitrified at the Waste Treatment and Immobilization Plant (WTP), which is a part of the safe and efficient retrieval, treatment, and disposal mission of the U.S. Department of Energy - Hanford Field Office. A portion of Hanford tank 241-AW-105 (referred to herein as AW-105) waste was retrieved by Hanford Tank Waste Operations and Closure (H2C) and transferred to Pacific Northwest National Laboratory (PNNL). Compared to previously received and vitrified wastes (AP-107, AP-101, AN-107 and AP-105), the concentration of potassium in AW-105 was greater by an order of magnitude.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗