Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Effective stress”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Stress effects on flow and transport in three-dimensional fracture networks

We investigate the effects of various external stress regimes on fracture apertures, fluid flow, and solute transport in three-dimensional fracture networks. We use well-established geomechanics equations coupled with discrete fracture network modeling to characterize changes in primary flow paths within a complex network as a function of stress magnitude and orientation. These changes manifest in the alterations of the fluid flow field and are measured in terms of Eulerian and Lagrangian flow observables including solute transport, which is a key problem in many hydrologic applications. Changes in primary flow paths affect the solute transport in the network by promoting anomalously early arrival or long tailing behavior. However, early time arrival is not ubiquitous in anisotropically stressed networks and in most cases there is a delayed arrival of solute, which is attributed to (i) the presence of low-velocity zones normal to the flow direction, (ii) the angle between flow direction and major compressive principal stress directions, and (iii) changes in the primary flow paths (i.e., increases in tortuosity and active network structure). Overall, flows become more channelized in anisotropically stressed fracture networks than in unstressed and isotropically stressed networks.

58 GEOSCIENCES↗
DOE OSTI2020

Voltage bias stress effects in metal halide perovskites are strongly dependent on morphology and ion migration pathways

The solar-to-power power conversion efficiencies (PCEs) of metal halide perovskites (MHP) have improved over the last decade using a wide variety of methods, including composition manipulation, dopant introduction, and interfacial buffers. These methods, however, have taken little regard for the electronic and interfacial effects such alterations may cause within devices under voltage bias stress – a condition required for most device operation. We investigate how halide and cation substitution in MHP structures [specifically, CH 3 NH 3 PbI 2.87 Cl 0.13 and Cs 0.1 (MA 0.17 FA 0.83 ) 0.9 Pb(I 0.83 Br 0.17 ) 3 ] effects the current behavior of devices while under a range of voltage bias stress in both light and dark conditions. Additionally, conducting in depth investigations into the electronic and morphological differences between these two MHP devices, we confirmed their unique voltage bias stress effects are due to intrinsic behavior within the perovskite structure. Importantly, we also determined how crystallite orientation can influence ion migration and therefore alter charge transport and current stability in MHP photovoltaic devices.

36 MATERIALS SCIENCE↗
NASA NTRS2004

Associative Flow Rule Used to Include Hydrostatic Stress Effects in Analysis of Strain-Rate-Dependent Deformation of Polymer Matrix Composites

designing reliable composite engine cases that are lighter than the metal cases in current use. The types of polymer matrix composites that are likely to be used in such an application have a deformation response that is nonlinear and that varies with strain rate. The nonlinearity and the strain-rate dependence of the composite response are due primarily to the matrix constituent. Therefore, in developing material models to be used in the design of impact-resistant composite engine cases, the deformation of the polymer matrix must be correctly analyzed. However, unlike in metals, the nonlinear response of polymers depends on the hydrostatic stresses, which must be accounted for within an analytical model. By applying micromechanics techniques along with given fiber properties, one can also determine the effects of the hydrostatic stresses in the polymer on the overall composite deformation response. First efforts to account for the hydrostatic stress effects in the composite deformation applied purely empirical methods that relied on composite-level data. In later efforts, to allow polymer properties to be characterized solely on the basis of polymer data, researchers at the NASA Glenn Research Center developed equations to model the polymers that were based on a non-associative flow rule, and efforts to use these equations to simulate the deformation of representative polymer materials were reasonably successful. However, these equations were found to have difficulty in correctly analyzing the multiaxial stress states found in the polymer matrix constituent of a composite material. To correct these difficulties, and to allow for the accurate simulation of the nonlinear strain-rate-dependent deformation analysis of polymer matrix composites, in the efforts reported here Glenn researchers reformulated the polymer constitutive equations from basic principles using the concept of an associative flow rule. These revised equations were characterized and validated in an experimental program carried out through a university grant with the Ohio State University, wherein tensile and shear deformation data were obtained for a representative polymer for strain rates ranging from quasi-static to high rates of several hundred per second. Tensile deformation data also were obtained over a variety of strain rates and fiber orientation angles for a representative polymer matrix composite composed using the polymer.

Goldberg, Robert K.↗
DOE OSTI2024

Uniaxial stress effect on the electronic structure of quantum materials

Uniaxial stress has proven to be a powerful experimental tuning parameter for effectively controlling lattice, charge, orbital, and spin degrees of freedom in quantum materials. In addition, its ability to manipulate the symmetry of materials has garnered significant attention. Recent technical progress to combine uniaxial stress cells with quantum oscillation and angle-resolved photoemission techniques allowed to study the electronic structure as function of uniaxial stress. This review provides an overview on experimental advancements in methods and examines studies on diverse quantum materials, encompassing the semimetal WTe 2 , the unconventional superconductor Sr 2 RuO 4 , Fe-based superconductors, and topological materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Uniaxial stress effect on the electronic structure of quantum materials

Uniaxial stress has proven to be a powerful experimental tuning parameter for effectively controlling lattice, charge, orbital, and spin degrees of freedom in quantum materials. In addition, its ability to manipulate the symmetry of materials has garnered significant attention. Recent technical progress to combine uniaxial stress cells with quantum oscillation and angle-resolved photoemission techniques allowed to study the electronic structure as function of uniaxial stress. This review provides an overview on experimental advancements in methods and examines studies on diverse quantum materials, encompassing the semimetal WTe2, the unconventional superconductor Sr2RuO4, Fe-based superconductors, and topological materials.

FOS: Physical sciences↗
NASA NTRS1985

Study of statis and dynamic stress effects in nonlinear solids

As the basic physical principles behind the low-field magnetoacoustic interactions have been unfolded, a new step in the present research had to be taken. First, the stress measurements began in samples obtained in real railroad wheel and rail materials. Second, the effect of texture, which is the prime obstacle of conventional NDE techniques, has been investigated. The first stage shows experimental results on these subjects again confirmed that the present technique is most suited for nondestructive stress characterization in steel components. The stress effects on the magnetoacoustic interaction obtained in a sample made from railroad rail which were very similar to those obtained previously in 1045 steel. These results being somewhat different from the results with low (1020) and high (1095) carbon steels, there seemed to be certain range of medium carbon steels having the same characteristics. Also, as expected from the model, the stress information obtained by this technique has been confirmed to be least affected by the presence of texture.

Namkung, M.↗
NASA NTRS1999

Hydrostatic Stress Effects in Metal Plasticity

Since the 1940s, the theory of plasticity has assumed that hydrostatic stress does not affect the yield or postyield behavior of metals. This assumption is based on the early work of Bridgman. Bridgman found that hydrostatic pressure (compressive stress) does not affect yield behavior until a substantial amount of pressure (greater than 100 ksi) is present. The objective of this study was to determine the effect of hydrostatic tension on yield behavior. Two different specimen geometries were examined: an equal-arm bend specimen and a double edge notch specimen. The presence of a notch is sufficient to develop high enough hydrostatic tensile stresses to affect yield. The von Mises yield function, which does not have a hydrostatic component, and the Drucker-Prager yield function, which includes a hydrostatic component, were used in finite element analyses of the two specimen geometries. The analyses were compared to test data from IN 100 specimens. For both geometries, the analyses using the Drucker-Prager yield function more closely simulated the test data. The von Mises yield function lead to 5-10% overprediction of the force-displacement or force-strain response of the test specimens.

Wilson, Christopher D.↗
NASA NTRS1999

Thermoelastic Stress Analysis: The Mean Stress Effect in Metallic Alloys

The primary objective of this study involved the utilization of the thermoelastic stress analysis (TSA) method to demonstrate the mean stress dependence of the thermoelastic constant. Titanium and nickel base alloys, commonly employed in aerospace gas turbines, were the materials of interest. The repeatability of the results was studied through a statistical analysis of the data. Although the mean stress dependence was well established, the ability to confidently quantify it was diminished by the experimental variations. If calibration of the thermoelastic response to mean stress can be successfully implemented, it is feasible to use the relationship to determine a structure's residual stress state.

Gyekenyesi, Andrew L.↗
NASA NTRS2022

Interactive Biogenic Emissions and Drought Stress Effects on Atmospheric Composition in NASA GISS ModelE

Drought is a hydroclimatic extreme that causes perturbations to the terrestrial biosphere and acts as a stressor on vegetation, affecting emissions patterns. During severe drought, isoprene emissions are reduced. In this paper, we focus on capturing this reduction signal by implementing a new percentile isoprene drought stress (y d ) algorithm in NASA GISS ModelE based on the MEGAN3 (Model of Emissions of Gases and Aerosols from Nature Version 3) approach as a function of a photosynthetic parameter (V c,max ) and water stress (β). Four global transient simulations from 2003–2013 are used to demonstrate the effect without y d (Default_ModelE) and with online y d (DroughtStress_ModelE). DroughtStress_ModelE is evaluated against the observed isoprene measurements at the Missouri Ozarks AmeriFlux (MOFLUX) site during the 2012 severe drought where improvements in the correlation coefficient indicate it is a suitable drought stress parameterization to capture the reduction signal during severe drought. The application of y d globally leads to a decadal average reduction of ∼ 2.7 %, which is equivalent to ∼14.6 Tg yr -1 of isoprene. The changes have larger impacts in regions such as the southeastern US. DroughtStress_ModelE is validated using the satellite ΩHCHO column from the Ozone Monitoring Instrument (OMI) and surface O 3 observations across regions of the US to examine the effect of drought on atmospheric composition. It was found that the inclusion of isoprene drought stress reduced the overestimation of ΩHCHO in Default_ModelE during the 2007 and 2011 southeastern US droughts and led to improvements in simulated O 3 during drought periods. We conclude that isoprene drought stress should be tuned on a model-by-model basis because the variables used in the parameterization responses are relative to the land surface model hydrology scheme (LSM) and the effects of y d application could be larger than seen here due to ModelE not having large biases of isoprene during severe drought.

drought stress effects↗
DOE OSTI2025

Contrasting c -axis and in-plane uniaxial stress effects on superconductivity and stripe order in La 1.885 Ba 0.115 CuO 4

The cuprate superconductor La 2−x Ba x CuO 4 (LBCO) near x = 0.125 is a striking example of intertwined electronic orders, where 3D superconductivity is anomalously suppressed, allowing spin and charge stripe order to develop. Understanding this interplay remains a key challenge in cuprates, highlighting the necessity of external tuning for deeper insight. While in-plane uniaxial stress enhances superconductivity and suppresses stripe order, the effects of c -axis compression remains largely unexplored. Here, we use muon spin rotation ( μ SR) and AC susceptibility with an in situ piezoelectric stress device to investigate the spin-stripe order and superconductivity in LBCO-0.115 under c-axis compression. The measurements reveal a gradual suppression of the superconducting transition temperature ( T c ) with increasing c -axis stress, in stark contrast to the strong enhancement observed under in-plane stress. We further show that while in-plane stress rapidly reduces both the magnetic volume fraction ( V m ) and the spin-stripe ordering temperature ( T so ), c-axis compression has no effect, with V m and T so exhibiting an almost unchanged behavior up to the highest applied stress of 0.21 GPa. These findings demonstrate a strong anisotropy in stress response.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Intermediate Principal Stress Effects on the 3D Cracking Behavior of Flawed Rocks Under True Triaxial Compression

Crack initiation, growth, and coalescence in flawed rocks have been extensively studied for 2D (planar, penetrating) flaws under uniaxial/biaxial compression. However, little is known as to the mechanisms and processes of cracking from 3D flaws under true triaxial compression, where the intermediate principal stress (σ 2 ) is distinguished from the major and minor principal stresses. In this work, we systematically investigate the effects of σ 2 on the 3D cracking behavior of rock specimens with preexisting flaws, through the use of mechanistic simulations of mixed-mode fracture in rocks. We explore how two characteristics of σ 2 , namely, (i) its orientation with respect to the flaw and (ii) its magnitude, affect two aspects of the cracking behavior, namely, (i) the cracking pattern and (ii) the peak stress. Results show that the orientation of σ 2 exerts more control over the cracking pattern than the flaw inclination angle. The peak stress becomes highest when σ 1 is parallel to the flaw, whereas it becomes lowest when σ 2 is parallel to the flaw. Also, the effects of σ 2 magnitude are more significant when σ 2 becomes more oblique to the flaw plane. On the basis of our observations, we propose mechanisms underlying the cracking behavior of 3D flawed rocks under true triaxial compression.

58 GEOSCIENCES↗
NASA NTRS1973

A review of the influence of physical condition parameters on a typical aerospace stress effect: Decompression sickness

The study examines data on episodes of decompression sickness, particularly from recent Navy work in which the event occurred under multiple stress conditions, to determine the extent to which decompression sickness might be predicted on the basis of personal characteristics such as age, weight, and physical condition. Such information should ultimately be useful for establishing medical selection criteria to screen individuals prior to participation inactivities involving extensive changes in ambient pressure, including those encountered in space operations. The main conclusions were as follows. There is a definite and positive relationship between increasing age and weight and the likelihood of decompression sickness. However, for predictive purposes, the relationship is low. To reduce the risk of bends, particularly for older individuals, strenuous exercise should be avoided immediately after ambient pressure changes. Temperatures should be kept at the low end of the comfort zone. For space activities, pressure changes of over 6-7 psi should be avoided. Prospective participants in future missions such as the Space Shuttle should not be excluded on the basis of age, certainly to age 60, if their general condition is reasonably good and they are not grossly obese. (Modified author abstract)

West, V. R.↗
NASA NTRS1979

Lubricant limiting shear stress effect on EHD film thickness

A Grubin-like EHD inlet analysis utilizing a non-linear viscous fluid model with a limiting shear stress is reported. The shear rheological equation requirs only a low shear stress viscosity and the limiting shear stress both functions of pressure. Values employed for these properties are taken from measurements on typical lubricants. Reductions of EHD film thickness are found to be up to 40 percent compared with the standard Grubin prediction for typical operating conditions. Slide-roll ratio, limiting shear stress dependence on pressure, and atmospheric pressure value of limiting shear stress are new variables required to determine film thickness with the first two being more important than the last. The EHD film thickness is reduced by increasing slide-roll ratio and/or decreasing the pressure dependence of the limiting shear stress.

Gecim, B.↗
NASA NTRS1990

Interlaminar shear stress effects on the postbuckling response of graphite-epoxy panels

The influence of shear flexibility on overall postbuckling response was assessed, and transverse shear stress distributions in relation to panel failure were examined. Nonlinear postbuckling results are obtained for finite element models based on classical laminated plate theory and first-order shear deformation theory. Good correlation between test and analysis is obtained. The results presented analytically substantiate the experimentally observed failure mode.

Engelstad, S. P.↗
NASA NTRS1990

Interlaminar shear stress effects on the postbuckling response of graphite-epoxy panels

The objectives of the study are to assess the influence of shear flexibility on overall postbuckling response, and to examine transverse shear stress distributions in relation to panel failure. Nonlinear postbuckling results are obtained for finite element models based on classical laminated plate theory and first-order shear deformation theory. Good correlation between test and analysis is obtained. The results presented in this paper analytically substantiate the experimentally observed failure mode.

Engelstad, S. P.↗
NASA NTRS1970

Diurnal rhythm of the pituitary-adrenocortical response to stress: effect of constant light and constant darkness

The existence of a biological rhythm in the response of animals to noxious stimuli and drugs is well known. However, the mechanism of this response is not well understood. This study was undertaken to describe the existence of a diurnal rhythm in the hypothalamic-pituitary-adrenocortical system before and after stress in female rats kept in controlled environmental conditions in 12L:12D, 24L:OD, or OL:24D. Plasma ACTH and plasma corticosterone concentrations were compared in unstressed animals. The time pattern in the response to stress was determined at four hourly intervals during a 24 hr period in which plasma ACTH and plasma corticosterone were measured at different time intervals. The stress response varied considerably with time of day in both magnitude and duration. The adrenals of rats exposed to constant light for 45 days atrophied, whereas the adrenals of animals kept in constant dark for the same period did not differ significantly from those of controls kept in 12L:12D. The increase in plasma ACTH in response to stress was greater both in the animals maintained in constant light and in constant dark than in the 12L:12D controls. Homeostatic mechanisms involved in these changes are discussed.

Photoperiod↗