Engineering PapersSearch

SEARCH · Engineering Papers

Results for “ERAD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Performance of a V/STOL tilt nacelle inlet with blowing boundary layer control

A scale model of a V/STOL tilt nacelle fitted to a 0.508 m single stage fan was tested in the NASA Lewis low speed wind tunnel to determine the effect of diffuser blowing on the inlet aerodynamics and aeromechanical performance. The test was conducted over a range of freestream speeds (up to 120 knots) and angles-of attack (up to 120 deg). In general, diffuser blowing had a beneficial affect on all performance parameters. The angle-of-attack range for a separation-free flow substantially increased, and the fan face distortion reduced with a corresponding increase in total pressure recovery. Discrete narrow band blade stress peaks which were common to the nonblowing (baseline) configuration were eradicated with diffuser blowing.

Johns, A. L.

Large arcuate scars: A geological legacy of the Earth's accretionary past

Immediately following accretion, the surface of the Earth was densely patterned with circular scars which were the surface expressions of 3-D craterform structures. In the course of geological time these structures would have become less and less visible due to the workings of the Earth's atmosphere, surface waters, and plate tectonics regime but there is no compelling reason to assume that they have been entirely eradicated. Furthermore, a very imperfect analogy with the other inner planets suggests that geological processes may not in fact be capable of totally erasing such deep features. Some illustrative examples of arcuate scars are discussed.

Saul, J. M.

Tunneling calculations for GaAs-Al(x)Ga(1-x)As graded band-gap sawtooth superlattices

The transmission resonance spectra and tunneling current-voltage characteristics for direct conduction band electrons in sawtooth GaAs-Al(x)Ga(1-x)As superlattices are computed. Only direct-gap interfaces are considered. It is found that sawtooth superlattices exhibit resonant tunneling similar to that in step superlattices, manifested by correlation of peaks and regions of negative differential resistance in the current-voltage curves with transmission resonances. The Stark shift of the resonances of step-barrier superlattices is a linear function of the field, whereas in sawtooth superlattices under strong fields the shift is not a simple function of the field. This follows from the different ways in which the two structures deform under uniform electric fields: the sawtooth deforms into a staircase, at which field strength all barriers to tunneling are eradicated. The step-barrier superlattice always presents some barrier to tunneling, no matter how high the electric field strength.

Forrest, Kathrine

Modelling Rift Valley fever (RVF) disease vector habitats using active and passive remote sensing systems

The NASA Ames Ecosystem Science and Technology Branch and the U.S. Army Medical Research Institute of Infectious Diseases are conducting research to detect Rift Valley fever (RVF) vector habitats in eastern Africa using active and passive remote-sensing. The normalized difference vegetation index (NDVI) calculated from Landsat TM and SPOT data is used to characterize the vegetation common to the Aedes mosquito. Relationships have been found between the highest NDVI and the 'dambo' habitat areas near Riuru, Kenya on both wet and dry data. High NDVI values, when combined with the vegetation classifications, are clearly related to the areas of vector habitats. SAR data have been proposed for use during the rainy season when optical systems are of minimal use and the short frequency and duration of the optimum RVF mosquito habitat conditions necessitate rapid evaluation of the vegetation/moisture conditions; only then can disease potential be stemmed and eradication efforts initiated.

Ambrosia, Vincent G.

The Management and Security Expert (MASE)

The Management and Security Expert (MASE) is a distributed expert system that monitors the operating systems and applications of a network. It is capable of gleaning the information provided by the different operating systems in order to optimize hardware and software performance; recognize potential hardware and/or software failure, and either repair the problem before it becomes an emergency, or notify the systems manager of the problem; and monitor applications and known security holes for indications of an intruder or virus. MASE can eradicate much of the guess work of system management.

Miller, Mark D.

Product assurance management and software product assurance

The evolution of software assurance is discussed. The definition and implementation of standards are considered. It is recommended that requirements be clarified at the start of a project. The need for quality assurance in hardware is identified as the coming trend in the production of high cost single units which call for eradication of all errors during the early stages of development. The need to apply quality assurance throughout the whole mission is stressed. The dangers of overpricing product assurance services is stressed.

Schneider, C.

Destruction and survival of polycyclic aromatic hydrocarbons in active galaxies

Infrared spectra of dusty galactic environments often contain emission features attributed to polycyclic aromatic hydrocarbons or PAHs, which can be considered to be very small grains or very large molecules. Although IR spectra of starburst galaxies almost always show these emission features, similar spectra of active galaxies are usually featureless. Even in those active galaxies that do exhibit PAH emission, the PAHs still appear to be eradicated from the nuclear region. This dichotomy suggests that PAHs are destroyed by the intense hard radiation field from an AGN. Laboratory experiments show that certain PAHs are, in fact, so effectively destroyed by individual EUV and X-ray photons that they cannot survive even at kiloparsec distances from active nuclei. Regions within active galaxies that do show PAH emission must therefore be shielded from the central X-ray source by a substantial column density of X-ray absorbing gas.

Voit, G. M.

Strength After Bouts of Eccentric or Concentric Actions

This study examined the influence of an initial bout of eccentric or concentric actions and a subsequent bout of eccentric actions on muscular strength. Twenty-four healthy males, 24-45 yr old, were placed in three groups that performed eccentric actions in bouts 1 and 2 (ECC/ECC, N = 8), concentric actions in bout 1, and eccentric actions in bout 2 (CON/ECC, N = 8) or served as controls (N = 8). Bouts involved unilateral actions with the left and right quadriceps femoris. Ten sets of 10 repetitions with an initial resistance equal to 85% of the eccentric or concentric one repetition maximum (1 RM) were performed for each bout. Three minutes of rest were given between sets and 3 wk between bouts. Two weeks before bout 1 and 1, 4, 7, and 10 d after bouts 1 and 2, eccentric and concentric 1 RM were measured for the right quadriceps femoris and a speed-torque relation established for the left quadriceps femoris. Eccentric and concentric 1 RM decreased (P less than 0.05) 32% 1 d after bout 1 for group ECC/ECC. The speed-torque relation was down-shifted (P less than 0.05) 38%. Eccentric 1 RM and eccentric and isometric torque returned to normal 6 d later. Concentric 1 RM and torque at 3.14 rad-s(exp -1) had not recovered on day 10 (-7% for both, P less than 0.05). Decreases in strength after bout 2 for group ECC/ECC only occurred on day 1 (-9% for concentric 1 RM and 16% downshift of the speed- torque relation). Group CONIECC showed the opposite responses; marked decreases in strength after bout 2 but not bout 1. The results indicate that the initial decrease in strength after performance of a novel bout of eccentric exercise is comparable for eccentric, concentric and isometric muscle actions. Recovery of strength, however, appears to occur more rapidly for eccentric and isometric actions. They suggest that performance of a prior bout of eccentric but not concentric actions, as done in this study, can essentially eradicate decreases in strength after a subsequent bout of eccentric exercise. It is suggested that neural factors are, in part, responsible for adaptations to eccentric exercise.

Golden, Catherine L.

Breakdown Degradation Associated with Elementary Screw Dislocations in 4H-SiC P(+)N Junction Rectifiers

It is well-known that SiC wafer quality deficiencies are delaying the realization of outstandingly superior 4H-SiC power electronics. While efforts to date have centered on eradicating micropipes (i.e., hollow core super-screw dislocations with Burgers vector greater than 2c), 4H-SiC wafers and epilayers also contain elementary screw dislocations (i.e., Burgers vector = lc with no hollow core) in densities on the order of thousands per sq cm, nearly 100-fold micropipe densities. This paper describes an initial study into the impact of elementary screw dislocations on the reverse-bias current-voltage (I-V) characteristics of 4H-SiC p(+)n diodes. First, Synchrotron White Beam X-ray Topography (SWBXT) was employed to map the exact locations of elementary screw dislocations within small-area 4H-SiC p(+)n mesa diodes. Then the high-field reverse leakage and breakdown properties of these diodes were subsequently characterized on a probing station outfitted with a dark box and video camera. Most devices without screw dislocations exhibited excellent characteristics, with no detectable leakage current prior to breakdown, a sharp breakdown I-V knee, and no visible concentration of breakdown current. In contrast devices that contained at least one elementary screw dislocation exhibited a 5% to 35% reduction in breakdown voltage, a softer breakdown I-V knee, and visible microplasmas in which highly localized breakdown current was concentrated. The locations of observed breakdown microplasmas corresponded exactly to the locations of elementary screw dislocations identified by SWBXT mapping. While not as detrimental to SiC device performance as micropipes, the undesirable breakdown characteristics of elementary screw dislocations could nevertheless adversely affect the performance and reliability of 4H-SiC power devices.

Neudeck, P. G.

Non-Micropipe Dislocations in 4H-SiC Devices: Electrical Properties and Device Technology Implications

It is well-known that SiC wafer quality deficiencies are delaying the realization of outstandingly superior 4H-SiC power electronics. While efforts to date have centered on eradicating micropipes (i.e., hollow core super-screw dislocations with Burgers vectors greater than or equal to 2c), 4H-SiC wafers and epilayers also contain elementary screw dislocations (i.e., Burgers vector = 1c with no hollow core) in densities on the order of thousands per sq cm, nearly 100-fold micropipe densities. While not nearly as detrimental to SiC device performance as micropipes, it has recently been demonstrated that elementary screw dislocations somewhat degrade the reverse leakage and breakdown properties of 4H-SiC p(+)n diodes. Diodes containing elementary screw dislocations exhibited a 5% to 35% reduction in breakdown voltage, higher pre-breakdown reverse leakage current, softer reverse breakdown I-V knee, and microplasmic breakdown current filaments that were non-catastrophic as measured under high series resistance biasing. This paper details continuing experimental and theoretical investigations into the electrical properties of 4H-SiC elementary screw dislocations. The nonuniform breakdown behavior of 4H-SiC p'n junctions containing elementary screw dislocations exhibits interesting physical parallels with nonuniform breakdown phenomena previously observed in other semiconductor materials. Based upon experimentally observed dislocation-assisted breakdown, a re-assessment of well-known physical models relating power device reliability to junction breakdown has been undertaken for 4H-SiC. The potential impact of these elementary screw dislocation defects on the performance and reliability of various 4H-SiC device technologies being developed for high-power applications will be discussed.

Neudeck, Philip G.

Behavior of Windblown Sand on Mars: Results from Single-Particle Experiments

Experiments are investigating the behavior of individual sand grains in the high-energy martian aeolian regime. Energy partitioning during impact of a saltating grain determines grain longevity, but it also influences the way in which the bed becomes mobilized by reptation. When single grains of sand are fired into loose beds, the bed can absorb up to 90% of the impact energy by momentum transfer to other grains; it has been discovered that the impacting grains cause circular craters even at low impact angles. Hundreds of grains can be splashed by a single high-velocity (100 m/s) impact causing more bed disturbance through reptation than previously thought. The research is supported by NASA's PG&G Program. Because the martian aeolian environment in both high energy and of long duration, the most mobile fractions of windblown sand should have eradicated themselves by attrition, unless sand supply has kept pace with destruction. It is therefore important to understand the rate of grain attrition in order to make sense of the existence of vast dune fields on Mars. Attrition, has been addressed in other studies, but precise data for a single saltating grain striking a loose bed of sand have not been acquired -- the quintessential case to be understood for dunes on Mars. To acquire these data, we are employing a compound crossbow which has the bolt-firing mechanism replaced with a pneumatically-automated sabot system. The sabot can launch individual grains of sand of any size between several millimeters and about 50 microns, at velocities up to 100m/s. This is around the maximum velocity expected for saltating grains on Mars. The sabot sled is equipped with photoelectric sensors for measuring shot velocity. Baffling of the grain's exit orifice has enabled projection of single grains without significant aerodynamic effects from the sabot. Grains are fired into loose beds of sand at about 15 degrees from the horizontal (typical saltation trajectory at impact) while being filmed on high-speed video. High-intensity pulse illumination for the grains is triggered by the solenoid-operated bow trigger. A 45 degree mirror over the impact site provides simultaneous horizontal and vertical images of the impact on each video frame. UV fluorescence is enabling grain and grain-fragment recovery. At 100 m/s, grains of all sizes shatter into many fragments when the sand is replaced with a solid target. Kinetic energy of the grains at this velocity exceeds the critical energy for catastrophic failure of minerals. Although probably exceptional as a grain speed, it suggests that conditions on Mars might elevate materials into an attrition regime not encountered on other planets; individual grains blown across rock pavements on Mars will have short lifespans. When experimental grains impact loose (dune) sand, much, if not most of the kinetic energy is converted into momentum of other grains. Using high-speed filming, the energy involved in splashing grains at the impact site can be derived from the size of the crater, the speed of the splashed grains, and the rebound speed of the impactor. The amount of energy partitioned into material failure (as opposed to momentum) is too small a fraction of the total to be calculated under these circumstances. This does not necessarily mean that little damage occurs to the grains (the full extent of the damage has yet to be determined) because only a small fraction of the impact energy is required for inducing brittle fracture. Damage is orders of magnitude less than during impact against solid surfaces.

Marshall, J. R.

Pest Control on the "Fly"

FlyCracker(R), a non-toxic and environmentally safe pesticide, can be used to treat and control fly problems in closed environments such as milking sheds, cattle barns and hutches, equine stables, swine pens, poultry plants, food-packing plants, and even restaurants, as well as in some outdoor animal husbandry environments. The product can be applied safely in the presence of animals and humans, and was recently permitted for use on organic farms as livestock production aids. FlyCracker's carbohydrate technology kills fly larvae within 24 hours. By killing larvae before they reach the adult stages, FlyCracker eradicates another potential breeding population. Because the process is physical-not chemical-flies and other insects never develop resistance to the treatment, giving way to unlimited use of product, while still keeping the same powerful effect.

Source record

Water for Two Worlds: Designing Terrestrial Applications for Exploration-class Sanitation Systems

At the United Nations Millennium Summit in September of 2000, the world leaders agreed on an ambitious agenda for reducing poverty and improving lives: the Millennium Development Goals (MDGs) , a list of issues they consider highly pernicious, threatening to human welfare and, thereby, to global security and prosperity. Among the eight goals are included fundamental human needs such as the eradication of extreme poverty and hunger, the promotion of gender equality, the reduction of child mortality and improvement of maternal health, and ensuring the sustainability of our shared environment. In order to help focus the efforts to meet these goals, the United Nations (UN) has established a set of eighteen concrete targets, each with an associated schedule. Among these is Target 10: "By 2015, reduce by half the proportion of people without access to safe drinking water." A closely related target of equal dignity was agreed at the World Summit on Sustainable Development (Johannesburg, September 2002): "By 2015, reduce by half the proportion of people without access to basic sanitation".

Adams, Constance

Water for Two Worlds: Designing Terrestrial Applications for Exploration-class Sanitation Systems

At the United Nations Millennium Summit in September of 2000, the world leaders agreed on an ambitious agenda for reducing poverty and improving lives: the Millennium Development Goals (MDGs), a list of issues they consider highly pernicious, threatening to human welfare and, thereby, to global security and prosperity. Among the eight goals are included fundamental human needs such as the eradication of extreme poverty and hunger, the promotion of gender equality, the reduction of child mortality and improvement of maternal health, and ensuring the sustainability of our shared environment. In order to help focus the efforts to meet these goals, the United Nations (UN) has established a set of eighteen concrete targets, each with an associated schedule. Among these is Target 10: "By 2015, reduce by half the proportion of people without access to safe drinking water." A closely related target of equal dignity was agreed at the World Summit on Sustainable Development (Johannesburg, September 2002): "By 2015, reduce by half the proportion of people without access to basic sanitation." One of the greatest successes in the development of Exploration-class technologies for closed-loop, sustainable support of long-duration human space missions has been the work both ESA and NASA have done in bioregenerative water reclamation (WRS), and secondarily, in solid-waste management. Solid-waste and WRS systems tend to be combined in the commercial world into the field of sanitation, although as we will see, the most essential principles of sustainable terrestrial sanitation actually insist upon the separation of solid and liquid excreta. Seeing the potential synergy between the space program ALS technologies developed for Mars and the urgent needs of hundreds of millions of people for secure access to clean water here on Earth, we set out to organize the adaptation of these technologies to help the United Nations Development Programme (UNDP) meet Target 10. In this paper, we will summarize the issues and results of the first "Water for Two Worlds" summit held in January of this year, describe,the status of the sustainable sanitation systems that are on the table for adaptation to widespread terrestrial use, and present fundamental strategies for forward work.

Adams, Constance

The NDSC ozone and temperature lidar alogorithm intercomparison ubutuatuve (A2I): project overview

In September 2003, the Lidar Working Group (LWG) of the Network for Detection of Stratospheric Change (NDSC) initiated an extensive project to compare the ozone and temperature algorithms used within NDSC. This initiative, referred to later as Algorithm Intercomparison Initiative (A2I), uses simulated lidar signals to test and compare various parts of the ozone and temperature lidar algorithms. In addition to the fact that it meets the requirement of the NDSC protocols, this exercise allows the detailed assessment, by all the participants, of some of the sources and magnitudes of various uncertainties associated with the algorithms, and/or with the theoretical assumptions made in these algorithms. The outcome of the A21 is to try to find common grounds in the way ozone and temperature can be retrieved in order to reduce and possibly eradicate discrepancies due to algorithm issues alone. Specific issues such as homogenizing the choice of Rayleigh extinction cross-sections, ozone absorption cross-sections, a priori information, and the definition of the vertical resolutions are among the primary targets of the A21 outcome.

lidar

Identification of Bacteria and Determination of Biological Indicators

The ultimate goal of planetary protection research is to develop superior strategies for inactivating resistance bearing micro-organisms like Rummeli - bacillus stabekisii. By first identifying the particular physiologic pathway and/or structural component of the cell/spore that affords it such elevated tolerance, eradication regimes can then be designed to target these resistance-conferring moieties without jeopardizing the structural integrity of spacecraft hardware. Furthermore, hospitals and government agencies frequently use biological indicators to ensure the efficacy of a wide range of sterilization processes. The spores of Rummelibacillus stabekisii, which are far more resistant to many of such perturbations, could likely serve as a more significant biological indicator for potential survival than those being used currently.

Venkateswaran, Kasthuri

Response of Staphylococcus Aureus to a Spaceflight Analogue

The decreased gravity of the spaceflight environment creates quiescent, low fluid shear conditions. This environment can impart considerable effects on the physiology of microorganisms as well as their interactions with potential hosts. Using the rotating wall vessel (RWV), as a spaceflight analogue, the consequence of low fluid shear culture on microbial pathogenesis has provided a better understanding of the risks to the astronaut crew from infectious microorganisms. While the outcome of low fluid shear culture has been investigated for several bacterial pathogens, little has been done to understand how this environmental factor affects Staphylococcus aureus. S. aureus is an opportunistic human pathogen which presents a high level of infection risk to the crew, as it has been isolated from both the space shuttle and International Space Station. Given that approximately forty percent of the population are carriers of the bacteria, eradication of this organism from in flight environments is impractical. These reasons have lead to us to assess the response of S. aureus to a reduced fluid shear environment. Culture in the RWV demonstrated that S. aureus grown under the low-shear condition had lower cell concentrations after 10 hours when compared to the control culture. Furthermore, the low-shear cultured bacteria displayed a reduction in carotenoid production, pigments responsible for their yellow/gold coloration. When exposed to various environmental stressors, post low-shear culture, a decrease in the ability to survive oxidative assault was observed compared to control cultures. The low fluid shear environment also resulted in a decrease in hemolysin secretion, a staphylococcal toxin responsible for red blood cell lysis. When challenged by the immune components present in human whole blood, low-shear cultured S. aureus demonstrated significantly reduced survival rates as compared to the control culture. Assays to determine the duration of these alterations demonstrated that the low-shear response could be lost in as few as 2.5 hours. These changes in phenotypic properties prompted investigation into variations occurring at the genetic level. Microarray analysis of low-shear cultured S. aureus revealed the differential regulation of genes involved in metabolism, stress response, and phosphate transfer. Additional genetic analysis with quantitative real-time PCR revealed alterations in the expression of Hfq, the conserved RNA chaperone protein involved in global gene regulation. Hfq has been connected to the regulation of a spaceflight microgravity response in S. typhimurium. These findings in S. aureus suggest an evolutionary conserved response to spaceflight conditions among structurally-diverse microorganisms. Furthermore, the reduction in pigmentation, hemolysin secretion, and survival against oxidative stress and immunologically active whole blood demonstrate an overall decrease in the virulence factors of S. aureus in response to spaceflight-like conditions.

Castro, S. L.

Second Cancers After Fractionated Radiotherapy: Stochastic Population Dynamics Effects

When ionizing radiation is used in cancer therapy it can induce second cancers in nearby organs. Mainly due to longer patient survival times, these second cancers have become of increasing concern. Estimating the risk of solid second cancers involves modeling: because of long latency times, available data is usually for older, obsolescent treatment regimens. Moreover, modeling second cancers gives unique insights into human carcinogenesis, since the therapy involves administering well characterized doses of a well studied carcinogen, followed by long-term monitoring. In addition to putative radiation initiation that produces pre-malignant cells, inactivation (i.e. cell killing), and subsequent cell repopulation by proliferation can be important at the doses relevant to second cancer situations. A recent initiation/inactivation/proliferation (IIP) model characterized quantitatively the observed occurrence of second breast and lung cancers, using a deterministic cell population dynamics approach. To analyze ifradiation-initiated pre-malignant clones become extinct before full repopulation can occur, we here give a stochastic version of this I I model. Combining Monte Carlo simulations with standard solutions for time-inhomogeneous birth-death equations, we show that repeated cycles of inactivation and repopulation, as occur during fractionated radiation therapy, can lead to distributions of pre-malignant cells per patient with variance >> mean, even when pre-malignant clones are Poisson-distributed. Thus fewer patients would be affected, but with a higher probability, than a deterministic model, tracking average pre-malignant cell numbers, would predict. Our results are applied to data on breast cancers after radiotherapy for Hodgkin disease. The stochastic IIP analysis, unlike the deterministic one, indicates: a) initiated, pre-malignant cells can have a growth advantage during repopulation, not just during the longer tumor latency period that follows; b) weekend treatment gaps during radiotherapy, apart from decreasing the probability of eradicating the primary cancer, substantially increase the risk of later second cancers.

Sachs, Rainer K.