Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Diesel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Pulsed laser heating of diesel engine and turbojet combustor soot: Changes in nanostructure and implications

Here, carbonaceous particulate produced by a diesel engine and turbojet engine combustor are analyzed by transmission electron microscopy (TEM) for differences in nanostructure before and after pulsed laser annealing. Soot is examined between low/high diesel engine torque and low/high turbojet engine thrust. Small differences in nascent nanostructure are magnified by the action of high-temperature annealing induced by pulsed laser heating. Lamellae length distributions show occurrence of graphitization while tortuosity analyses reveal lamellae straightening. Differences in internal particle structure (hollow shells versus internal graphitic ribbons) are interpreted as due to higher internal sp3 and O-atom content under the higher power conditions with hypothesized greater turbulence and resulting partial premixing. TEM in concert with fringe analyses reveal that a similar degree of annealing occurs in the primary particles in soot from both diesel engine and turbojet engine combustors—despite the aggregate and primary size differences between these sources. Implications of these results for source identification of the combustion particulate and for laser-induced incandescence (LII) measurements of concentration are discussed with inter-instrument comparison of soot mass from both diesel and turbojet soot sources.

42 ENGINEERING↗
DOE OSTI2023

An Experimental Comparison of Cyclic Variations in Diesel–Natural Gas and POMDME–Natural Gas Dual Fuel Combustion

Abstract Cyclic variations in internal combustion engines are caused by various factors, including combustion mixture stratification, in-cylinder flows, local fluctuations in air-fuel ratio, etc. Cyclic variations have a profound impact on engine performance and emissions. In this study, cyclic variations in dual fuel combustion are analyzed, comparing diesel–natural gas (NG) and polyoxymethylene dimethyl ether (POMDME)-NG dual fuel combustion. Cyclic variability was initially quantified using the coefficient of variation of gross indicated mean effective pressure (IMEPg) computed from experimental cylinder pressure data. The cases analyzed in this study had a coefficient of variation (COV) of IMEPg greater than or around 5%, which was the lower limit of onset of instability for this engine. Experiments were performed at two fixed start of injection (SOI) of high-cetane fuel: 310 CAD and 350 CAD. For all experiments, a constant load of 5 bar IMEPg was maintained, and the intake boost pressure and rail pressure were fixed at 1.5 bar and 500 bar, respectively. For each case, 1000 cycles of cylinder pressure data were recorded, filtered, and processed using an in-house heat release analysis code for each cycle. A comparison between individual cycles and the “ensemble averaged cycle” was made for both diesel–NG and POMDME–NG combustion. For the early SOI of 310 CAD, the peak cylinder pressure fluctuations of individual cycle were found to be ± 15 bar for both fuel combinations, compared to the ensemble averaged cycle, and < 1/10th of the cycles had an IMEPg lower than 0.05 bar of the ensemble averaged cycle. However, the peak pressure fluctuations were found to be lower for POMDME–NG (±3 bar) than diesel–NG dual fuel combustion at 350 CAD SOI, indicating lower cyclic variations. The higher reactivity of POMDME helped reduce fluctuations in combustion phasing at the retarded SOI. The presence of cycles of deterioration and cycles of recovery were also observed with diesel–NG combustion for 310 CAD SOI, and the scatter in the IMEPg return map was similar for both fuel combinations. The IMEPg return map for POMDME–NG combustion was less scattered at the 350 CAD SOI.

Engineering↗
DOE OSTI2022

Design and Optimization of Structured Multi-Functional Trapping Catalysts for Conversion of Hydrocarbons and NOx from Diesel and Advanced Combustion Engines

Oxides of nitrogen in the form of nitric oxide (NO) and nitrogen dioxide (NO 2 ) commonly referred to as NOx, is one of the two chemical precursors that lead to ground-level ozone, a ubiquitous air pollutant in urban areas. A major source of NOx is generated by equipment and vehicles powered by diesel engines, which have a combustion exhaust that contains NOx in the presence of excess O 2 . Vehicular emission control catalysts are ineffective in eliminating CO, hydrocarbons, and NO x during engine cold-start when exhaust temperatures are below 200°C. The objective of the project was to develop and demonstrate a multi-functional, catalyzed trap that enables vehicles with advanced combustion strategies to meet Tier 3 emissions standards while achieving the 150 °C challenge for sustained co-oxidation of HCs and CO and ≥90% NO trapping and release during warmup. Specifically, the multi-functional Lean HC+NOx (LHCNT) was developed for application in the exhaust aftertreatment of conventional diesel engines and engines having low temperature combustion (LTC) regimes. Activities included the design and synthesis of adsorbents and catalysts, screening and evaluation. Passive NOx absorbers (PNA), hydrocarbon (HC) traps, and oxidation catalysts (OC) were evaluated for use in series or as integrated devices. Predictive tools were developed utilizing the characterization and analysis of these materials, and an emission system was designed and optimized utilizing the catalyst systems. Microkinetic models were developed for the PNA for the simple NO-only feed and complex feed containing CO, H 2 , and model hydrocarbons (ethylene and dodecane). A first-principles, mechanistic-based model of the PNA was developed which utilized molecular-scale estimates (density functional theory) of energy barriers, mechanistic-based kinetics and realistic treatments of the flow and transport processes. Two new oxidation catalysts were developed (PdCu alloy, mixed copper-ceria-cobalt oxide), both of which significantly lessened the detrimental inhibition by CO on hydrocarbon and NO oxidation. A method for lessening the detrimental impact of CO on PNA activity was developed that involves use of an oxidation catalyst upstream of the PNA. The SwRI Ectolab TM burner system was applied to evaluate the baseline PNA material and confirmed performance comparable to the benchflow PNA studies using simulated exhaust. Spatially-resolved mass spectrometry (SpaciMS) was used to measure the transient spatial profiles of reacting species spanning the length of a three-function LHCNT containing PNA, HCT, and OC. The findings from this study provide diesel vehicle and catalyst companies valuable information to develop more cost effective emission control catalysts which helps to expand the use of more fuel efficient diesel power. The fundamental modeling and experimental tools and findings from this project can be applied to catalyst technologies used in the energy and chemical industries. The project led to 14 publications in the peer-reviewed literature with 2 additional currently under review. Finally, the project also led to training of several doctoral students who were placed in research jobs in industry and academia. Specifically, Mugdha Ambast (UH) has joined Cummins, Kevin Gu (UVa) has joined GM, and Abhay Gupta (UH) is to join Caterpillar.

42 ENGINEERING↗
DOE OSTI2023

Production of bio-diesel blend stocks via acid-catalyzed dehydration of ethanol oligomerization products

Ethanol is the most widely produced biofuel in the world. Gasoline demand is projected to decrease in the next 20 years largely due to an increase in electric vehicles. Diesel fuel demand is projected to continue to increase. Long-chain mono C10+ ethers have high cetane numbers and appropriate physical properties to be blended at high levels into petroleum diesel fuel. A techno-economic analysis shows that the ethers can be produced at prices similar to biodiesel. In our presentation we will show the catalytic chemistry involved in our ethanol to diesel approach, the engine and physical measurements of the produced diesel-range ethers, and a summary of the techno-economic analysis.

Canales, Emmanuel↗
DOE OSTI2024

Development of advanced combustion strategies for direct injection heavy duty LPG engines to achieve near-diesel engine efficiency

The Vehicle Technologies Office funds early-stage, high-risk research to develop technology upon which industry can implement innovative transportation energy technologies that increase efficiency, decrease cost, and expand use of domestic energy sources, such as liquefied petroleum gas (LPG). To improve the viability of medium and heavy-duty vehicles the LPG engine efficiency must be closer to that of diesel. This work addresses fundamental limitations to achieve diesel-like efficiencies in heavy duty on-road LPG engines. The primary goal of this research is to achieve diesel-like efficiencies in heavy duty on-road LPG engines, focusing on the Cummins 15-liter engine platform (baseline diesel efficiency of 44% at peak torque). That goal has been achieved, though more work is needed to facilitate practical implementation of the developed technologies.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Machine learning models for maintenance cost estimation in delivery trucks using diesel and natural gas fuels

The maintenance costs can represent about 15%–60% of the cost of produced goods depending on the type of goods transported. To comply with stringent emissions regulations, diesel engines are incorporated with complex after-treatment systems that demand increased maintenance. The availability of alternative fuels such as natural gas and propane has fostered the natural gas and propane powertrain systems as well as electrification options for heavy- and medium-duty vehicles. A critical barrier to adopting alternative fuel vehicles has been the lack of knowledge on comparative vehicle maintenance/repair costs with conventional diesel. Moreover, the region of operation, the type of vehicle operation, and seasonal temperature changes also affect the duty cycle which impacts the maintenance and repair costs. This study focuses on estimating the cost-per-mile for heavy-duty vehicles using machine learning models such as random forest, xgboost, neural networks, and a super-learner model. The super-learner model achieved an error as low as 0.0068 $/mile for mean absolute error and 0.0086 $/mile for root mean square error with a coefficient of determination/R-Squared of 97.28%. Specifically, the paper investigates the data collected from the maintenance and repair costs associated with delivery trucks using diesel and natural gas fuels. Since the availability of data is the major constraint, we leveraged the data collected by West Virginia University and the partnership with fleet companies. This allows for additional information related to maintenance costs and fleet-specific maintenance practices of alternative fuel vehicles. This study promotes clean fuel technologies and enables fleet management companies to adopt alternative fuel vehicles in case of similar or lower cost of maintenance compared to diesel vehicles resulting in reduced emissions and total cost of ownership.

Katreddi, Sasanka↗
DOE OSTI2024

Spatially-resolved soot evolution and statistics in high-pressure diesel spray flames using two-color pyrometry

Previous studies of diesel spray flames have focused on details of the sooting behavior mainly during the quasi-steady period, but few have considered the spatially-resolved transient evolution in combination with injection-to-injection variations. In this study, a 500-injection data set is utilized to investigate the temporal evolution of a spray flame during auto-ignition, the premixed burn phase, and the quasi-steady period. Spatially-resolved OH* chemiluminescence data provide ignition delay times and reaction zone locations. Two-color pyrom-etry with a vastly improved optical system is used to quantify spatially-resolved soot evolution and its statistical variations. The ambient thermodynamic con-ditions are slightly below those in modern diesel engines, resulting in longer lift-off lengths and lower overall soot production. Spatially, soot formation in the lift-off region is small, but appreciable soot forms in the jet core and jet head regions, while it oxidizes gradually on the jet periphery. Total soot mass profiles indicate that regions with larger local soot mass take longer to form, but are the first to oxidize. Probability distributions of soot mass in localized regions indicate that a few injections with high soot mass bias the average soot mass data towards higher values. Altogether, results show good agreement with previous studies employing different diagnostic techniques while providing statistical details of transient and localized soot behavior in high pressure diesel spray flames in support of the related modeling efforts.

09 BIOMASS FUELS↗
DOE OSTI2025

An experimental and numerical investigation of HD diesel engine DOC efficiency in oxidizing NO to NO 2

Reducing pollutant emissions from heavy-duty (HD) diesel engines is critical due to their significant environmental impact, particularly concerning NOx emissions. Understanding and optimizing modern diesel oxidation catalyst (DOC) and selective catalytic reduction (SCR) performance is essential for improving exhaust aftertreatment (EAT) system efficiency to meet stringent emissions regulations. The oxidation of nitric oxide (NO) to nitrogen dioxide (NO 2 ) in DOC plays a key role in improving SCR efficiency in reducing NO x . This study investigates the DOC performance in oxidizing NO to NO2 and its impact on the SCR efficiency of a 2021 MY Navistar E39 HD diesel engine. The influence of engine speed, load, exhaust gas temperature, and composition on DOC efficiency is experimentally investigated. The relationships between DOC inlet temperature, oxygen availability and NO 2 /NO x ratio at the DOC inlet are examined to better understand their effects on the overall DOC efficiency. The results indicate that DOC NO oxidation efficiency is highly dependent on exhaust temperature, with optimal oxidation occurring within a specific temperature range (275-350°C). Below this threshold, the chemical reactions are kinetically limited, while at higher temperatures, thermodynamic constraints reduce the efficiency of DOC in oxidizing NO to NO 2 . The experimental data further reveal that the NO 2 /NO x ratio peaks at medium loads before declining at higher loads due to reduced residence time and mass transfer effects. Additionally, the SCR NO x conversion efficiency is significantly influenced by the NO 2 /NO x ratio, achieving peak performance when the NO 2 /NO x ratio approaches 0.5. A DOC chemistry model was developed and validated against the experimental data to predict DOC oxidation behavior under various operating conditions. The findings of this study provide insights into the interdependencies between DOC and SCR performance, contributing to the optimization of SCR systems for optimized NOx reduction.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

A Hybrid Heavy Duty Diesel Power System for Off-Road Applications—Concept Validation

A multiyear power system R&D program was completed with the objective of developing an off-road hybrid heavy duty diesel engine with front end accessory drive-integrated energy storage. This system was validated to deliver 10.5–25.6% reduction in fuel consumption over current Tier 4 Final-based 18L diesel engines, over various off-road machine application cycles. The power system consisted of a downsized heavy-duty diesel 13L engine containing advanced combustion technologies, capable of elevated peak cylinder pressures and thermal efficiencies, thermal barrier coatings, exhaust waste heat recovery via SuperTurbo™ turbocompounding, and hybrid energy assisting and recovery through both mechanical and electrical systems. Following the concept definition, design, and analysis phases of the program, the final phase focused on building and validating the performance and efficiency in laboratory tests. While aspects of the system such as start/stop and reduced off-road cooling package energy losses were only analytically evaluated, the main 13L concept engine with full hybrid system was successfully built and tested in steady-state and in transient certification and real-world application cycles. Extensive simulations in Caterpillar's DYNASTY™ software environment utilized the validation test data to assess performance more fully and confidently over varied cycles and strategies. An average fuel consumption reduction of 17.9% was realized, and the majority (~13%) of the benefit stemmed from the core concept 13L engine. In conclusion, a total cost of ownership analysis provides context to commercial viability and where adoption focus should be placed.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Microbial Analysis of 100-N Borehole Samples: Estimation of Diesel and BTEX Degrading Bacterial Populations

Historical unplanned releases at the UPR-100-N-17 166-N Diesel Oil Supply Line Leak waste site located within the 100-NR-1 OU resulted in diesel fuel contamination of the unsaturated vadose zone and site groundwater. Enhanced in situ bioremediation of the deep vadose zone was the final remedy decision for the 100-NR-1 Operable Unit (OU) and the full-scale bioventing demo began in 2012. For this remedy, oxygen is actively supplied to the deep vadose zone to stimulate aerobic hydrocarbon degrading microorganisms to metabolize petroleum contamination. Degradation rate calculations based on vadose zone respirometry measurements, however, have indicated declining activity over recent years, though the precise reason for this apparent decline has not been determined. In this investigation 100-NR-1 OU sediment cores were analyzed for total microbial biomass, as well as enumeration of diesel and BTEX degrading bacteria to determine if these microbial populations have declined relative to previous measurements taken in 2009.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

How Does the COVID-19 Pandemic Affect Transport-Related Diesel Consumption in the U.S.?

Understanding how energy usage reacts to the COVID-19 pandemic is essential to making strategic policy decisions. This study aims to quantify the pandemic’s influences on diesel consumption and explore the potential causes of the differences across regions. We found various levels of reduction in diesel consumption at the state level during the pandemic in the U.S. Many factors, including COVID-19 cases and commodities being moved, are associated with these reductions. In particular, at the state level, more truck/train shipping of minerals, coal, and forest products associates with fewer truck activities and greater decreases in diesel consumption.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Detailed Compositional Comparison of Hydrogenated Vegetable Oil with Several Diesel Fuels and Their Effects on Engine-Out Emissions

The Coordinating Research Council (CRC) is actively involved in developing and applying advanced analytical techniques to the chemical characterization of transportation fuels. Here, this article complements a 2017 CRC project to quantify and compare the effects of a commercially available renewable diesel fuel (hydrotreated vegetable oil [HVO]) and an ultralow sulfur diesel (ULSD) fuel on engine-out gaseous and particulate matter (PM) emissions from a light-duty vehicle. Results showed that the combustion of HVO fuel had an advantage over ULSD in terms of lowering engine-out emissions (THC, CO, NO x , etc.). Furthermore, this advantage is strongly related to the fuel composition. This article summarizes the results of advanced and comprehensive analytical tests on the same ULSD and HVO fuels and attempts to connect some of the engine-out emissions results to fuel composition and specific chemical structures. A variety of test methods, generally unavailable in combination, were employed, such as one-dimensional (1D) and two-dimensional (2D) gas chromatography (GC), nuclear magnetic resonance spectroscopy (NMR), and high-pressure solid-liquid phase transition experiments. In summary, the ULSD sample was found to have representation across the expected set of hydrocarbon classes typical for the sample type. Interestingly, a high content of cycloparaffins (>50 wt%) and a very low content of diaromatics (~2 wt%) were present. While not without precedent, these are higher and lower, respectively, than typically found for commercial ULSD compositions. In contrast, HVO was found to consist of only two hydrocarbon classes: n-paraffins (~10 wt%) and iso-paraffins (~90 wt%), both predominantly in a narrow carbon atom number range (i.e., C14–C18). HVO engine-out emissions results for the LA-92 and steady-state testing can be tracked to the narrow carbon atom number range of the n-paraffins and iso-paraffins, which result in a high cetane number fuel having a narrow distillation range. Previously, the low-temperature operability of HVO has been a concern, but that appears not be the case for this particular HVO. HVO and ULSD were evaluated at pressures up to ~275 MPa and found to have comparable solid-liquid equilibria despite significant compositional differences.

09 BIOMASS FUELS↗
DOE OSTI2023

Diesel fuel properties of renewable polyoxymethylene ethers with structural diversity

Polyoxymethylene ethers (POMEs) are a class of low-soot and high-cetane oxygenate oligomers of structure RO-(CH 2 O-) $n$ -R, with different chain lengths ($n$) and end-groups (R) that determine their diesel-like fuel properties. Commercial POMEs with methyl end-groups (MM-POME 3-6 ) exhibit undesirably low energy density and high-water solubility. A previous computational assessment indicated that the lower heating value (LHV) and water solubility for MM-POME 3-6 both improve upon end-group exchange with larger butyl, $iso$-butyl and $iso$-pentyl end-groups. Here, we expanded upon our initial trans-acetalization reaction that employed 1-butanol to install butyl end-groups to also include branched, higher carbon-number end-groups using $iso$-butanol and fusel oil as reagents. Additionally, these new products are termed $i$B*POME 1-6 , and FOil*POME 1-5 , respectively, and collectively referred to as R*POMEs. They possess the advantaged properties of the parent MM-POME 3-6 while exhibiting higher LHV (31 MJ kg -1 and 28 MJ kg -1 for $i$B*POME 1-6 , and FOil*POME 1-5 , respectively) and much reduced water solubility (2.7 g L -1 and 1 g L -1 for $i$B*POME 1-6 , and FOil*POME 1-5 , respectively). Additional fuel property analyses were performed using 20 vol% blends of the R*POMEs with a base diesel fuel. Overall, the greater energy density and decreased water solubility of the R*POMEs, as well as their synergistic blending with diesel at moderate blend levels, provide the greatest benefits to consumers and position this group of products as an environmentally friendlier blendstock alternative to the commercially available MM-POME 3-6 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Scale-Up Studies for the Dehydration of C 4+ Alcohols into Drop-In Diesel Fuel

Herein, we demonstrate the production of liter quantities of drop-in diesel-range ethers from biomass-derived alcohols. We report scale-up resultsfor the dehydration of a mixture of C 4+ alcohols using powder and pellet zeolite Ycatalyst in continuous flow and batch reactors. The activity of zeolite Y decreaseswith the introduction of an alumina binder. Large alcohols, as well as branchedand secondary alcohols, increase the coke content over the pellet Y catalyst. Thepellet formulation had lower carbon balances and selectivity to C 10+ ethers,suggesting that the pellet formulation increases alcohol absorption and cokeproduction. Crushing the pellet Y catalyst to smaller particle sizes does notrecover the activity of zeolite Y in its powder form. Cold flow experiments showthat particle agglomeration contributes to pressure buildup in the continuous flowreactor. C 10+ ether blends can be produced in batch reactors at high alcohol conversion regimes. One liter of a diesel #2 blend wasproduced by scaling up this reaction. The final blend consists of a substantial portion of C 10+ ethers (63.7 wt %), followed by heavyunknown products (27.4 wt %). Furthermore, the final alcohol and butyl ether concentration values were 7.3 and 1.5 wt %, respectively. Theblendstock reported in this paper can satisfy diesel #2 ASTM standards for density, cloud point, flashpoint, and cetane number.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Performance Evaluation of a Microgrid System with Grid-Forming and Grid-Following Inverters with Diesel Generators: Insights From Hardware Experiments

This paper presents a comprehensive performance evaluation of a microgrid system integrating grid-forming (GFM) inverters, grid-following (GFL) inverters, and a diesel generator, focusing on their interactions and behavior under various dynamic events. The study is conducted using a pure hardware setup comprising two GFM inverters, one GFL inverter, a diesel generator, load banks, a point of common coupling (PCC), and an emulated main grid. The evaluation specifically examines dynamic scenarios, including voltage jumps, phase jumps, rate of change of frequency (ROCOF), synchronization, and islanding operations, which pose critical challenges to system stability. Among all the tests conducted, the overloading and phase jump tests proved to be the most challenging. The capacity of the DC side is crucial for withstanding overloading and grid disturbance tests; otherwise, GFM inverters frequently trip due to DC undervoltage. Throughout all grid disturbance tests, the diesel generator consistently stands out as the most robust and reliable GFM unit in the system. Overall, insights from these hardware experiments shed light on the response characteristics of different generation types during grid disturbances and identify potential stability concerns in such hybrid microgrid systems.

14 SOLAR ENERGY↗
DOE OSTI2023

Lubricant impacts on piston deposit formation in the Enterprise marine diesel research engine

The impact of lubricant formulation on piston deposits was studied using the Enterprise, a reduced-scale, single-cylinder, two-stroke crosshead marine diesel research engine. The Enterprise engine was specially designed for marine diesel lubricant research, with a custom reduced-scale cylinder lubricant injection system and extensive instrumentation of thermal boundary conditions on both the liner and piston. Lubricant conditions typical of full-scale marine diesel engines are obtained by matching mean piston speed, liner temperature profile, and combustion metrics to realistic values.Piston deposit thicknesses were measured after a set period of operation, with a focus on lubricant-based deposits on the lands and ring grooves, using both optical and contact-based measurement techniques. Engine operation for each lubricant was conducted according to a standardized protocol, with precise control of engine speed and load, cylinder lubricant injection rate, coolant temperatures, and system oil temperature; the liner and piston temperatures are continuously monitored during operation. After operation with each lubricant was completed, the engine was disassembled, and the piston and ring deposits were characterized. The piston was then thoroughly cleaned, and the lubricant system flushed, between each lubricant formulation being evaluated. The impacts on piston deposits of the lubricants being evaluated can thus be accurately quantified and are described herein.

Kaul, Brian↗
DOE OSTI2023

Effects of soybean varieties on life-cycle greenhouse gas emissions of biodiesel and renewable diesel

This study presents a life-cycle analysis (LCA) of the greenhouse gas (GHG) emissions of biodiesel (BD) and renewable diesel (RD) produced from soybean varieties with altered oil profiles and meal composition. The varieties evaluated include those with high oleic oil content (78% of oil being oleic oil vs. the current content of 25%), high lipid content (25% vs. the current content of 19%) or high protein content (45% vs. the current content of 35%). The results suggest that high-oleic soybean oil could reduce GHG emissions of RD by 1 g CO 2 e/MJ by reducing hydrogen consumption in the hydro-treating stage of RD production. With the default allocation method (mass-based allocation between oil and meal), changes in lipid and protein contents have negligible impacts on GHG emissions of BD/RD pathways. Since high-protein soybean meal has a higher nutrient value, we employed the market-based allocation for sensitivity analysis. Assuming a market price of $1.17/dry kg and an average of two substitute feeds with similar protein contents (corn gluten and fish meal), the allocation factor for soybean meal increases from 63 to 81%. Compared with the results for the case with commodity soybean using mass allocation, GHG emissions could be 1.9 and 1.8 g CO 2 e/MJ lower for BD and RD, respectively. In addition to product-level LCA, we employed a land-based LCA to evaluate the effect of soybean properties on product slates with the same land area and the associated displacement of conventional products. The results suggest that high-lipid soybeans may offer more GHG savings than other varieties as the higher BD/RD yield replaces more fossil diesel. © 2023 UChicago Argonne, LLC, Operator of Argonne National Laboratory and Northrup, Ag. Biofuels, Bioproducts and Biorefining published by Society of Industrial Chemistry and John Wiley & Sons Ltd.

09 BIOMASS FUELS↗
DOE OSTI2025

Renewable diesel and bio-aromatics production from waste cooking oil using ethanol as a hydrogen donor in deoxygenation reaction

Biofuels offer a promising solution in the fight against climate change. With a global increase in waste cooking oil, this research investigated the production of bio-hydrogenated diesel (BHD) from waste cooking oil, using ethanol as a hydrogen donor in the deoxygenation process. A hydrolyzed waste cooking oil model compound served as the feedstock, and the deoxygenation was performed at 300–400 °C. The catalysts used in the experiments were 2.6 wt% Ni and 7.8 wt% Mo (2.6Ni-7.8Mo) and 10 wt% Ni and 5 wt% Mo (10Ni-5Mo) on γ-Al 2 O 3 . The results showed that ethanol is an effective hydrogen donor for biofuel production without the need for external hydrogen at an elevated pressure. The increasing temperature enhanced the free fatty acid (FFA) conversion and n-alkane selectivity in the oil product, with the highest FFA conversion and alkane selectivity of 100 % and 46 %, respectively, observed at 400 °C for the sulfided 10Ni-5Mo catalyst. On the other hand, 2.6Ni-7.8Mo offers 100 % FFA conversion with a lower n-alkane selectivity of 35 % at identical temperatures. The total acid number (TAN) of the oil products decreased from 174.03 mg KOH/g of feedstock to 9.43 and 8.67 mg KOH/g with the sulfided 2.6Ni-7.8Mo and 10Ni-5Mo catalysts, respectively. Both the catalysts achieved similar heating values (~43 MJ/kg) at 400 °C. This is a significant improvement to the HHV of the feedstock, which was 36.02 MJ/kg. Additionally, aromatic compounds, mainly BTXE (benzene, toluene, xylene, and ethylbenzene), were also produced. Compared to glycerol as a hydrogen donor, ethanol more effectively increased n-alkane selectivity due to its higher effective hydrogen-to-carbon ratio (H/C eff ). Conversely, glycerol was more advantageous for achieving greater selectivity towards BTXE compounds due to its lower H/C eff , which potentially leads to coke formation. Since aromatic compounds are intermediates in coke production, glycerol provides higher aromatic selectivity than ethanol. Finally, this study presents an alternative pathway for producing diesel fuel from waste cooking oil using ethanol as a hydrogen donor.

36 MATERIALS SCIENCE↗