Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DOPES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Characterization of n-Type Iodine-Doped and Indium-Doped CdTe/Cd-Se-Te Thin Films Fabricated by Close-Spaced Sublimation Epitaxy

In this study, n-type CdTe thin films, specifically iodine-doped CdTe (CdTe:I), indium-doped CdTe (CdTe:In), and indium-doped Cd-Se-Te (CST:In), were synthesized using close-spaced sublimation epitaxy (CSSE). Characterization techniques secondary ion mass spectrometry (SIMS), electron backscatter diffraction (EBSD), Hall-effect measurements, and time-resolved photoluminescence (TRPL) were employed to analyze the chemical, structural, and electronic properties of these materials. The results indicated epitaxial single crystal CSSE films grew on the single crystal substrates, with carrier density ranging from 10^14 - 10^16 cm -3 , and after post-annealing, the minority-carrier lifetimes reach near the radiative limit. Additionally, a preliminary exploration of homojunction structures with an n- type (CdTe:In /CST:In /CdTe:I) /CdTe:P /Cu /Mo configuration was performed. The best device performance was achieved with CdTe:I including CdS aiding in band alignment, resulting in a power conversion efficiency (..eta..) of 2.61% with open circuit voltage (Voc) of 850 mV, fill factor (FF) of 47.8%, and short-circuit current (Jsc) of 6.44 mA/cm 2 . The observed low Jsc and efficiency may be attributed to a buried junction and a poor interface, due to dopant interdiffusion. Consequently, further investigations focusing on interface optimization, diffusion blocking, and reduced recombination through passivation, are crucial to enhancing the efficiency of CSSE CdTe homojunction devices in the future.

cadmium compounds↗
DOE OSTI2026

Luminescence properties of europium doped and sodium co-doped LiCaAlF 6

This paper serves as a literature review of scintillating thermal neutron detectors, along with a study of sodium and europium doped LiCaAlF 6 (LiCAF) polycrystalline material. A set of polycrystalline LiCAF material was synthesized with 2 molar percent of europium (Eu 2+ ) and co-doped with 0, 1, and 2 molar percent of sodium (Na + ), with a stoichiometric synthesis approach in a glassy-carbon crucible. The quantum yield and photoluminescence spectrum at room temperature was analyzed. For the first time, we have demonstrated that Na-co-doping directly alters the quantum yield. The quantum yield for LiCAF:Eu 2+ , with 0, 1, and 2 molar percent of sodium (Na + ) was 0.578, 0.635, and 0.580, respectively. The photoluminescence (PL) spectrum was also analyzed for all samples. The photo-luminescence excitation (PLE) spectrum showed a maximum at 300 nm, while the emission spectrum showed a maximum at 370 nm, corresponding to the Eu 2+ 5d-4f transitions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Luminescence and Scintillation in the Niobium Doped Oxyfluoride Rb4Ge5O9F6:Nb

A new niobium-doped inorganic scintillating oxyfluoride, Rb4Ge5O9F6:Nb, was synthesized in single crystal form by high-temperature flux growth. The host structure, Rb4Ge5O9F6, crystallizes in the orthorhombic space group Pbcn with lattice parameters a = 6.98430(10) Å, b = 11.7265(2) Å, and c = 19.2732(3) Å, consisting of germanium oxyfluoride layers made up of Ge3O9 units connected by GeO3F3 octahedra. In its pure form, Rb4Ge5O9F6 shows neither luminescence nor scintillation but when doped with niobium, Rb4Ge5O9F6:Nb exhibits bright blue luminescence and scintillation. The isostructural doped structure, Rb4Ge5O9F6:Nb, crystallizes in the orthorhombic space group Pbcn with lattice parameters a = 6.9960(3) Å, b = 11.7464(6) Å, and c = 19.3341(9) Å. X-ray absorption near edge structure (XANES) and extended X-ray absorption fine structure (EXAFS) measurements suggest that the niobium is located in an octahedral coordination environment. Optical measurements inform us that the niobium dopant acts as the activator. The synthesis, structure, and optical properties are reported, including radioluminescence (RL) measurements under X-ray irradiation.

Carone, Darren (ORCID:0000000164014098)↗
DOE OSTI2023

The Effect of Dopant Concentration and Annealing Treatments on N-Type Iodine Doped CdTe

We report properties of highly conducting n-type cadmium telluride single crystals doped with iodine (CdTe:I). These crystals were grown with dopant concentrations in the range of 10^17 cm-3 to 10^19 cm-3 by Modified Vertical Bridgman (MVB) melt growth. Post-growth dopant activation, including Cd annealing, Te annealing, and rapid thermal annealing (RTA), was applied to improve free carrier density. The structural, optical, and electrical properties were analyzed by Glow Discharge Mass Spectroscopy (GDMS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), Photoluminescence Spectroscopy (PL), optical absorption, Hall measurements, Capacitance-Voltage (CV) measurements, and time-resolved photoluminescence (TRPL). The results indicate that Cd annealing is the most effective activation method to get 100% donor activation (n is approximately 2 x 10^18 cm-3), which is close to the room temperature solubility limit of iodine. This leads to the lowest resistivity and the highest mobility. Moreover, this data suggests a potential role of Cd vacancy-related defects on electrical self-compensation.

annealing↗
DOE OSTI2021

Promoting Atomically Dispersed MnN 4 Sites via Sulfur Doping for Oxygen Reduction: Unveiling Intrinsic Activity and Degradation in Fuel Cells

Carbon supported and nitrogen coordinated single Mn site catalysts (Mn-N-C) catalysts are the most desirable platinum group metal (PGM)-free cathode catalysts for proton exchange membrane fuel cells (PEMFCs) due to their insignificant Fenton reactions (vs. Fe), earth abundances (vs. Co) and encouraging activity and stability. However, current Mn-N-C catalysts suffer from high over-potential due to low intrinsic activity and less dense MnN 4 sites. Herein, we present sulfur-doped Mn-N-C catalyst (Mn-N-C-S) synthesized through an effective adsorption-pyrolysis process. Using electron microscopy and X-ray absorption spectroscopy (XAS) techniques, we verify the uniform dispersion of MnN 4 sites and confirm the effect of S doping on the Mn-N coordination. The Mn-N-C-S catalyst exhibits a favorable oxygen reduction reaction (ORR) activity in acidic media relative to the S-free Mn-N-C catalyst. The corresponding membrane electrode assembly (MEA) generated a remarkable performance with a peak power density of 500 mW cm -2 under a realistic H 2 /air environment. The constant voltage tests of fuel cells confirm the much-enhanced stability of the Mn-N-C-S catalyst compared to the Fe-N-C and Fe-N-C-S catalysts. The electron microscopy and Fourier transform XAS analysis provide insights into catalyst degradation associated with Mn oxidation and agglomeration. The theoretical calculation elucidates that the promoted ORR activity is mainly attributed to the spatial effect stemmed from the repulsive interaction between the ORR intermediates and adjacent S do-pants.

25 ENERGY STORAGE↗
NASA NTRS1919

Airplane dopes and doping

Cellulose acetate and cellulose nitrate are the important constituents of airplane dopes in use at the present time, but planes were treated with other materials in the experimental stages of flying. The above compounds belong to the class of colloids and are of value because they produce a shrinking action on the fabric when drying out of solution, rendering it drum tight. Other colloids possessing the same property have been proposed and tried. In the first stages of the development of dope, however, shrinkage was not considered. The fabric was treated merely to render it waterproof. The first airplanes constructed were covered with cotton fabric stretched as tightly as possible over the winds, fuselage, etc., and flying was possible only in fine weather. The necessity of an airplane which would fly under all weather conditions at once became apparent. Then followed experiments with rubberized fabrics, fabrics treated with glue rendered insoluble by formaldehyde or bichromate, fabrics treated with drying and nondrying oils, shellac, casein, etc. It was found that fabrics treated as above lost their tension in damp weather, and the oil from the motor penetrated the proofing material and weakened the fabric. For the most part the film of material lacked durability. Cellulose nitrate lacquers, however were found to be more satisfactory under varying weather conditions, added less weight to the planes, and were easily applied. On the other hand, they were highly inflammable, and oil from the motor penetrated the film of cellulose nitrate, causing the tension of the fabric to be relaxed.

PROTECTIVE COATINGS AND COVERINGS↗
DOE OSTI2025

Facet-Dependent Doping and Dopant-Dependent Faceting in Si-Doped GaAsSb Nanowires

Here, we correlate the spatial distributions of Si, Sb, and rotational twins in Si-doped GaAs 1-x Sb x nanowires. GaAs 1-x Sb x nanowires were grown epitaxially on Si(111) substrates by tuning process conditions to achieve repeated nucleation of rotational twins and growth along the [111]B direction; dilute Sb and Si fluxes were chosen to create a sufficient twin density to achieve high yield while avoiding growth of the wurtzite phase. While the impact of Si and Sb on twin density and nanowire growth rate has been previously reported, the facet-dependent incorporation of these species has not been established. Scanning transmission electron microscopy was used to confirm that Sb incorporates preferentially on the (111)B facets relative to {1 ̅1 ̅0} facets prior to nucleation of a rotational twin. With periodic twinning, this facet dependence leads to alternating regions of enriched and depleted Sb concentration attributed to a growth rate-dependent Sb-As-exchange mechanism. Atom probe tomography measurements establish that while Si doping is not perturbed by twinning on (111)B facets, Si and Sb concentrations are anti-correlated for growth on non-(111)B facets. Density functional theory calculations underpin a thermodynamic model that explains the observed anisotropies in dopant incorporation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electro-Optical Characterization of Arsenic-Doped CdSeTe and CdTe Solar Cell Absorbers Doped in-situ During Close Space Sublimation

Most contemporary device models predict that an acceptor concentration of at least 10^16 cm^-3 is required to reach an open circuit voltage of 1 V in polycrystalline CdTe-based solar cells. While copper has traditionally been used as the de facto p-type dopant in polycrystalline cadmium telluride (CdTe) and cadmium selenide telluride (CdSeTe), reaching high acceptor concentrations has proved to be challenging in such devices due to significant dopant compensation. The acceptor concentration in copper-doped CdTe and CdSeTe typically ranges from 10^13 to 10^15 cm^-3 and routinely exhibit low external radiative efficiencies below 0.01%, limiting their implied voltage (i.e., quasi-Fermi level splitting) to approximately 900 mV. As an alternative to copper, this work explores the use of arsenic as a p-type dopant for CdTe and CdSeTe. Using a novel technique in which a thin layer of arsenic-containing material is deposited and used as a reservoir for arsenic to diffuse into a front layer of previously undoped material, this contribution demonstrates that high external radiative efficiencies are achievable, a direct result of combined high acceptor concentrations and long minority-carrier lifetimes in the absorber. This leads to improved implied voltages, and indicates that As-doping represents a promising pathway towards improving the external voltage of CdSeTe/CdTe solar cells.

cadmium telluride↗
DOE OSTI2023

Spin-exchange carrier multiplication in manganese-doped colloidal quantum dots

Abstract Carrier multiplication is a process whereby a kinetic energy of a carrier relaxes via generation of additional electron–hole pairs (excitons). This effect has been extensively studied in the context of advanced photoconversion as it could boost the yield of generated excitons. Carrier multiplication is driven by carrier–carrier interactions that lead to excitation of a valence-band electron to the conduction band. Normally, the rate of phonon-assisted relaxation exceeds that of Coulombic collisions, which limits the carrier multiplication yield. Here we show that this limitation can be overcome by exploiting not ‘direct’ but ‘spin-exchange’ Coulomb interactions in manganese-doped core/shell PbSe/CdSe quantum dots. In these structures, carrier multiplication occurs via two spin-exchange steps. First, an exciton generated in the CdSe shell is rapidly transferred to a Mn dopant. Then, the excited Mn ion undergoes spin-flip relaxation via a spin-conserving pathway, which creates two excitons in the PbSe core. Due to the extremely fast, subpicosecond timescales of spin-exchange interactions, the Mn-doped quantum dots exhibit an up-to-threefold enhancement of the multiexciton yield versus the undoped samples, which points towards the considerable potential of spin-exchange carrier multiplication in advanced photoconversion.

36 MATERIALS SCIENCE↗
DOE OSTI2021

CdSexTe1-x/CdTe Devices with Reduced Interface Recombination Through Novel Back Contacts and Group-V Doping

Since excellent carrier lifetimes and front interface electronic quality are now achieved, rear interface recombination can limit V OC in CdSexTe1-x/CdTe solar cells. Several back-contact structures for devices were fabricated using combinations of tellurium, aluminum oxide, amorphous silicon, and indium tin oxide (ITO). Time-resolved photoluminescence was used to characterize such structures. We show increasingly improved interface passivation through the subsequent use of aluminum oxide, amorphous silicon, and ITO. Additionally, we show that arsenic-doped absorbers form a more passive interface with numerous back contact structures.

aluminum oxide↗
DOE OSTI2024

Site‐selective fluorescence and spectroscopic properties of Yb‐doped lanthanum titanate glasses

Abstract Ytterbium‐doped lanthanum titanate glasses were prepared by levitation melting for the detailed characterization of the spectroscopic properties in the rare‐earth titanate glass host. Low‐temperature fluorescence spectroscopy reveals distinct site‐selectivity in both static and lifetime fluorescence measurements suggesting an absence of clustering as well as significant variation of local ytterbium environments. Typical site‐selectivity behavior of a shrinking Stark manifold with lower excitation energy is observed. At 77 K, both the mean emission frequency and the fluorescence lifetime initially increase as the excitation energy decreases from about 11100 to 10750 and then slightly decrease at lower excitation energy. Temperature‐dependent lifetime measurements between 77 and 420 K show a decreasing lifetime with increasing temperature and are well described by a two‐level thermal activation model. The temperature‐dependent fluorescence spectroscopy coupled with a room temperature white light absorption measurement allow the determination of the Stark energy levels of in lanthanum titanate glass as well as the calculation of the laser cross‐sections.

Materials Science↗
DOE OSTI2020

Micro-Tubular Solid Oxide Fuel Cell Polarization and Impedance Variation With Thin Porous Samarium-Doped Ceria and Gadolinium-Doped Ceria Buffer Layer Thickness

Abstract Porous buffer layers for anode-supported solid oxide fuel cells (SOFCs) have been investigated for many years with different thicknesses of the buffer layer in each study. In this work, micro-tubular SOFCs having samarium-doped ceria (SDC) and gadolinium-doped ceria (GDC) buffer layers are compared using the current–voltage technique, electrochemical impedance spectroscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The thickness of the porous SDC and GDC buffer layer is investigated systematically with the thickness varying between 0.3 and 2.0 μm. The power density varies between 212 and 1004 mW/cm2 for samples having different SDC buffer layer thickness. Comparable changes occur for the SOFCs with a GDC buffer layer, but less variation in polarization losses resulted. Variation in electrochemical performance varies due to changes in ohmic resistance, cathode activation polarization, and interfacial reactions between the cathode and electrolyte materials.

Electrochemistry↗