Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cross Flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Optimization of Orifice Geometry for Cross-Flow Mixing in a Cylindrical Duct

Mixing of gaseous jets in a cross-flow has significant applications in engineering, one example of which is the dilution zone of a gas turbine combustor. Despite years of study, the design of the jet injection in combustors is largely based on practical experience. The emergence of NO(x) regulations for stationary gas turbines and the anticipation of aero-engine regulations requires an improved understanding of jet mixing as new combustor concepts are introduced. For example, the success of the staged combustor to reduce the emission of NO(x) is almost entirely dependent upon the rapid and complete dilution of the rich zone products within the mixing section. It is these mixing challenges to which the present study is directed. A series of experiments was undertaken to delineate the optimal mixer orifice geometry. A cross-flow to core-flow momentum-flux ratio of 40 and a mass flow ratio of 2.5 were selected as representative of a conventional design. An experimental test matrix was designed around three variables: the number of orifices, the orifice length-to- width ratio, and the orifice angle. A regression analysis was performed on the data to arrive at an interpolating equation that predicted the mixing performance of orifice geometry combinations within the range of the test matrix parameters. Results indicate that the best mixing orifice geometry tested involves eight orifices with a long-to-short side aspect ratio of 3.5 at a twenty-three degree inclination from the center-line of the mixing section.

Kroll, J. T.↗
NASA NTRS2000

Bubble Formation from Wall Orifice in Liquid Cross-Flow Under Low Gravity

Two-phase flows present a wide variety of applications for spacecraft thermal control systems design. Bubble formation and detachment is an integral part of the two phase flow science. The objective of the present work is to experimentally investigate the effects of liquid cross-flow velocity, gas flow rate, and orifice diameter on bubble formation in a wall-bubble injection configuration. Data were taken mainly under reduced gravity conditions but some data were taken in normal gravity for comparison. The reduced gravity experiment was conducted aboard the NASA DC-9 Reduced Gravity Aircraft. The results show that the process of bubble formation and detachment depends on gravity, the orifice diameter, the gas flow rate, and the liquid cross-flow velocity. The data are analyzed based on a force balance, and two different detachment mechanisms are identified. When the gas momentum is large, the bubble detaches from the injection orifice as the gas momentum overcomes the attaching effects of liquid drag and inertia. The surface tension force is much reduced because a large part of the bubble pinning edge at the orifice is lost as the bubble axis is tilted by the liquid flow. When the gas momentum is small, the force balance in the liquid flow direction is important, and the bubble detaches when the bubble axis inclination exceeds a certain angle.

Nahra, Henry K.↗
NASA NTRS1995

Nonlinear stability of non-stationary cross-flow vortices in compressible boundary layers

The nonlinear evolution of long wavelength non-stationary cross-flow vortices in a compressible boundary layer is investigated and the work extends that of Gajjar (1994) to flows involving multiple critical layers. The basic flow profile considered in this paper is that appropriate for a fully three-dimensional boundary layer with O(1) Mach number and with wall heating or cooling. The governing equations for the evolution of the cross-flow vortex are obtained and some special cases are discussed. One special case includes linear theory where exact analytic expressions for the growth rate of the vortices are obtained. Another special case is a generalization of the Bassom & Gajjar (1988) results for neutral waves to compressible flows. The viscous correction to the growth rate is derived and it is shown how the unsteady nonlinear critical layer structure merges with that for a Haberman type of viscous critical layer.

Gajjar, J. S. B.↗
NASA NTRS1979

A study of viscous cross-flow effects on circular cylinders at high Reynolds numbers

Results of experimental studies on viscous cross-flow over circular cylinders for Reynolds numbers from 0.15 x 10 to the 6th to 10.9 x 10 to the 6th at Mach numbers of less than 0.3 are presented and compared with previous work where possible. Results presented include the variation of static cross-flow drag coefficients with both Reynolds number and ratio of surface roughness to model diameter, the variation of Strouhal number with Reynolds number and the dynamic variation of surface static pressure coefficients with both angular position around the cylinder and Reynolds number. The effects of end-plates on flow around two-dimensional bluff-bodies and of tunnel blockage on drag measurements are also discussed.

James, W. D.↗
NASA NTRS1998

Reduction of Jet Penetration in a Cross-Flow by Using Tabs

A tab placed suitably on a nozzle that produces a jet in a cross-flow can reduce the penetration of the jet. This effect, achieved when the tab is placed on the windward side of the nozzle relative to the cross flow, may be of interest in film cooling applications. Wind tunnel experiments are carried out, in the momentum ratio (J) range of 10-90, to investigate the tab geometry that would maximize this effect. The preliminary results show that a 'delta tab' having a base width approximately fifty percent of the nozzle diameter may be considered optimum. With a given tab size, the effect is more pronounced at higher J. Reduction in jet penetration by as much as 40% is observed. Comparable reduction in jet penetration is also obtained when a triangular shaped tab is placed flush with the tunnel wall or with its apex tilted down into the jet nozzle (the 'delta tab' being the configuration in which the apex is tilted up). However, the delta tab involves the least flow blockage and pressure loss. Relative to the baseline case, the lateral spreading of the jet is found to be more with the delta tab but less with other orientations of the tab.

Zaman, K. B. M. Q.↗
NASA NTRS1994

Influence of cross-flow on nonlinear Tollmien-Schlichting/vortex interaction

The transition of an incompressible three-dimensional boundary layer with strong cross-flow is considered theoretically and computationally in the context of vortex/wave interactions. Specifically the work centers on two lower-branch Tollmien-Schlichting waves which mutually interact nonlinearly to induce a longitudinal vortex flow. The vortex motion in turn gives rise to significant wave modulation via wall-shear forcing. The characteristic Reynolds number is large and, as a consequence, the waves' and the vortex motion are governed primarily by triple deck theory. The nonlinear interaction is captured by a viscous partial-differential system for the vortex coupled with a pair of amplitude equations for each wave pressure. Following analysis and computation over a wide range of parameters, three distinct responses are found to emerge in the nonlinear behavior of the flow solution downstream: an algebraic finite-distance singularity, far-downstream saturation or far-downstream wave decay leaving pure vortex flow. These depend on the input conditions, the wave angles and the size of the cross flow.

Davis, D. A. R.↗
NASA NTRS2003

Active Control of Jets in Cross-Flow for Film Cooling Applications

Jets in cross-flow have applications in film cooling of gas turbine vanes, blades and combustor liners. Their cooling effectiveness depends on the extent to which the cool jet-fluid adheres to the cooled component surface. Lift-off of the cooling jet flow or other mechanisms promoting mixing, cause loss of cooling effectiveness as they allow the hot "free-stream" fluid to come in contact with the component surface. The premise of this project is that cooling effectiveness can be improved by actively controlling (e.9. forcing, pulsing) the jet flow. Active control can be applied to prevent/delay lift-off and suppress mixing. Furthermore, an actively controlled film-cooling system coupled with appropriate sensory input (e.g. temperature or heat flux) can adapt to spatial and temporal variations of the hot-gas path. Thus, it is conceivable that the efficiency of film-cooling systems can be improved, resulting in coolant fluid economy. It is envisioned that Micro Electro-Mechanical Systems (MEMS) will play a role in the realization of such systems. As a first step, a feasibility study will be conducted to evaluate the concept, identify actuation and sensory elements and develop a control strategy. Part of this study will be the design of a proof-of-concept experiment and collection of necessary data.

Nikitopoulos, Dimitris E.↗
NASA NTRS1978

Round jet in a cross flow - Influence of injection angle on vortex properties

A model is developed to infer the properties of a pair of diffuse contrarotating vortices for perpendicular jet injection into the cross flow. Attention is given to pressure distribution on the surface where the jet exhausts, especially in terms of V/STOL applications. A V/STOL wind tunnel experiment is described, whereby a round jet of air (10.16 cm dia) was discharged through a horizontal flat plate into the cross flow of the wind tunnel test section at angles of 45, 60, 75, and 90 deg. Results indicate that the effective vortex strength for both velocity ratios is highest near the jet orifice, and decreases as the vortices are swept downstream, at which point the effective vortex spacing increases. In addition, the core radius of the vortex exhibits properties similar to those of the effective vortex spacing

Krausche, D.↗
DOE OSTI2021

Performance Data from a 1-Meter Cross-flow Turbine with High Deflection Hydrofoils

Performance data of a 1-meter diameter cross-flow tidal turbine consisting of three NACA 0018 blades with two support struts with high deflection hydrofoils. Data was collected at the University of New Hampshire Jere A. Chase Ocean Engineering Lab within the tow tank. Three turbine parameters were varied: the blade materials, blade shape, and support strut position. A detailed description of the testing set-up and data files contained within the compressed "Turbine_Performance_Data.zip" file is in the "ReadMe.txt" file. Review of the original dataset "_Ver1" found that one of the tests had issues with one of the two redundant sensors. Resources were updated by replacing the dataset with measurements from the redundant sensor and are provided as version 2 "_Ver2".

16 TIDAL AND WAVE POWER↗
NASA NTRS1972

Cross flow in a starved EHD contact

An analysis of lubrication cross flow effects under starved elastohydrodynamic conditions is presented. Starvation is defined as any operating condition such that an increase in oil available to the contact will result in an increase in film thickness. Starved EHD behavior is considered in several situations: (1) when no new oil enters the contact, and (2) when a step change in one of the rolling parameters is introduced at an equilibrium contact. Based on the fact that important oil flow within the Hertz zone is across the rolling contact direction, it is possible to formulate a simple theory which explains quantitatively some aspects of starved ball bearing behavior.

Kingsburg, E. P.↗
NASA NTRS1992

Analysis of penetration and mixing of gas jets in supersonic cross flow

The JETPEN analysis for gas jets in a supersonic cross flow developed earlier at APL/JHU has been extended in several important ways. First, the treatment of cases with injection at angles other than 90 deg has been redone. Next, the second of the three regions formerly treated has been eliminated. Third, the region downstream of the Mach disk for underexpanded cases has been reformulated such that turbulent entrainment of main stream fluid into the plume is modeled, and the equations of motion are solved marching downstream. These changes now permit prediction of the variation in composition, mixing area growth and all other flow variables along the plume. The analysis has been verified by comparison of predictions and experiment over a wide range of conditions. The result is an analysis capable of reliable predictions of the major flowfield variables that can be run on a PC.

Billig, F. S.↗
DOE OSTI2023

Computational Fluid Dynamics Study of a Cross-Flow Marine Hydrokinetic Turbine and the Combined Influence of Struts and Helical Blades

A computational fluid dynamics study was performed for a cross-flow marine hydrokinetic turbine. The analysis was done in three dimensions and used the unsteady Reynolds-averaged Navier-Stokes solver in the commercial code STAR-CCM+. The base turbine configuration is the RivGen(R) Turbine, designed by the Ocean Renewable Power Company. A convergence and uncertainty analysis was performed for both the spatial and temporal discretization; this was done using the base configuration, which features support struts and helical foils. Both struts and helical blades introduce three-dimensional flow effects, influencing the complex flow phenomenon of dynamic stall. The study compares the relative impact of struts on power performance and blade loading for both helical and straight blades, and found that for this turbine the relative loss in power from struts was lower with helical blades.

CFD↗
NASA NTRS2003

Prediction of Bubble Diameter at Detachment from a Wall Orifice in Liquid Cross Flow Under Reduced and Normal Gravity Conditions

Bubble formation and detachment is an integral part of the two-phase flow science. The objective of the present work is to theoretically investigate the effects of liquid cross-flow velocity, gas flow rate embodied in the momentum flux force, and orifice diameter on bubble formation in a wall-bubble injection configuration. A two-dimensional one-stage theoretical model based on a global force balance on the bubble evolving from a wall orifice in a cross liquid flow is presented in this work. In this model, relevant forces acting on the evolving bubble are expressed in terms of the bubble center of mass coordinates and solved simultaneously. Relevant forces in low gravity included the momentum flux, shear-lift, surface tension, drag and inertia forces. Under normal gravity conditions, the buoyancy force, which is dominant under such conditions, can be added to the force balance. Two detachment criteria were applicable depending on the gas to liquid momentum force ratio. For low ratios, the time when the bubble acceleration in the direction of the detachment angle is greater or equal to zero is calculated from the bubble x and y coordinates. This time is taken as the time at which all the detaching forces that are acting on the bubble are greater or equal to the attaching forces. For high gas to liquid momentum force ratios, the time at which the y coordinate less the bubble radius equals zero is calculated. The bubble diameter is evaluated at this time as the diameter at detachment from the fact that the bubble volume is simply given by the product of the gas flow rate and time elapsed. Comparison of the model s predictions was also made with predictions from a two-dimensional normal gravity model based on Kumar-Kuloor formulation and such a comparison is presented in this work.

Nahra, Henry K.↗
DOE OSTI2023

Computational Fluid Dynamics Study of a Cross-Flow Marine Hydrokinetic Turbine and the Combined Influence of Struts and Helical Blades: Preprint

A computational fluid dynamics study was performed for a cross-flow marine hydro-kinetic turbine. The analysis was done in three dimensions and used the unsteady Reynolds averaged Navier-Stokes solver in the commercial code STAR-CCM+. The base turbine configuration is the RivGen® Turbine, designed by the Ocean Renewable Power Company (ORPC). A convergence and uncertainty analysis was performed for both the spatial and temporal discretization; this was done using the base configuration which features support struts and helical foils. The proposed study aims to compare the impact of the struts on both power performance and blade loading for helical and straight blades.

CFD↗