Results for “Continuous Insulation” — Page 3

NASA NTRS2010

Thermographic Methods of Detecting Insulation Voids in Large Cryogenic Tanks

Four very large (900Kgal) cryogenic liquid hydrogen and oxygen storage tanks at Kennedy Space Center's LC-39 launch pads were constructed in 1965 to support the Apollo/Saturn V Program and continue to support the Space Shuttle Program. These double-walled spherical tanks with powdered insulation in the annular region, have received minimal refurbishment or even inspection over the years. Intrusively inspecting these tanks would mean a significant down time to the program as the cryogenic liquid and the perlite insulation would have to be removed which would be a significant task and long-term schedule disruption. A study of the tanks was performed to determine the extent to which performance and structural information could be revealed without intrusive inspection. Thermal images of the tanks were taken over a variety of environmental conditions to determine the best conditions under which to compare and use thermography as a health monitoring technique as the tanks continue to age. The settling and subsequent compaction of insulation is a serious concern for cryogenic tanks. Comparison of images from the tanks reveals significant variations in the insulation in the annual regions and point to the use of thermography as a way to monitor for insulation migration and possible compaction. These measurements, when combined with mathematical models of historical boil-off data provide key insight to the condition of the vessels. Acceptance testing methods for new tanks, before they are filled with cryogenic commodity (and thereby thermally cycled), are needed and we explore how thermography can be used to accomplish this.

Arens, Ellen↗

NASA NTRS2021

Orion Meteoroid and Debris Analysis with a Single Kevlar® Layer Enhancement to the Propulsion Tank Multi-Layer Insulation: Comparison of the Observed Data and the Adjusted Ballistic Models

In a continual mass optimization effort for the Orion vehicle by NASA and its prime contractor Lockheed Martin Space, along with the European Space Agency (ESA) and its contractors Airbus and Thales Alenia Space-Italy (TAS-I), a series of shield characterization shots have been performed to quantify the ballistic enhancement of a single-layer of Kevlar® in multi-layer insulation (MLI). This enhanced MLI is part of Orion’s propulsion subsystem, and it is planned to replace a double-layer Kevlar® configuration starting at the Artemis IV mission. This effort has included fifty-two shield characterization shots for five different shield configurations over the four Orion propellant storage vessels. These storage vessels are located in the European Service Module (ESM). This shield characterization has been managed by the Hypervelocity Impact Technology (HVIT) group in NASA Astromaterials Research and Exploration Sciences at Johnson Space Center (JSC) for the NASA Engineering and Safety Center (NESC) and the Multi-Purpose Crew Vehicle (MPCV) program office in coordination with Lockheed Martin Space and Thales Alenia Space-Italy (TAS-I). The shield characterization has used the two-stage, light-gas-gun at the Remote Hypervelocity Test Laboratory (RHTL) of NASA JSC White Sands Test Facility (WSTF) for acceleration of projectiles to representative orbital impact speeds. From this shield characterization effort, a revised ballistic limiting equation (BLE) has been developed for each of the five representative shielding configurations of the ESM pressure vessels. This document provides a brief description of the shield configurations considered for the Orion program and the shield characterization findings. These results are compared to the assumed BLE for each configuration going into the Artemis missions that utilize this version of ballistic enhanced MLI. The models are integrated into a fourteen day High Lunar Orbit (HLO) mission as a representative reliability prediction impact for Orion, and it has been found that the predicted risk of a loss-of-crew (LOC) event is actually a little less than half of the assumed value that launched this design modification opportunity.

Joshua E Miller↗

NASA NTRS1985

Space shuttle program solid rocket booster decelerator subsystem

The recovery of the Solid Rocket Boosters presented a major challenge. The SRB represents the largest payload ever recovered and presents the added complication that it is continually emitting hot gases and burning particles of insulation and other debris. Some items, such as portions of the nozzle, are large enough to burn through the nylon parachute material. The SRB Decelerator Subsystem program was highly successful in that no SRB has been lost as a result of inadequate performance of the DSS.

Barnard, J. W.↗

NASA NTRS1987

Investigation of the acoustic properties of composite materials

An effort to provide inspection of the bondlines in the Space Shuttle Solid Rocket Motor (SRM) is discussed. Investigation of the bondlines in the membrane region of the SRM has centered on representative samples provided by Morton Thiokol. These samples have pull-tabs, or in one case grafoil inserts, to simulate delaminations at various points in the multilayer structure of steel case, liner, insulation, liner, and propellant. Discussed here is the continuing approach to examining these defects which is predicated on a model of an ultrasonic wave propagating in a lossy multilayer resonant structure, the experimental arrangements used, and the results of these experiments.

Smith, B. T.↗

NASA NTRS2015

Insulation Reformulation Development

The current Space Launch System (SLS) internal solid rocket motor insulation, polybenzimidazole acrylonitrile butadiene rubber (PBI-NBR), is a new insulation that replaced asbestos-based insulations found in Space Shuttle heritage solid rocket boosters. PBI-NBR has some outstanding characteristics such as an excellent thermal erosion resistance, low thermal conductivity, and low density. PBI-NBR also has some significant challenges associated with its use: Air entrainment/entrapment during manufacture and lay-up/cure and low mechanical properties such as tensile strength, modulus, and fracture toughness. This technology development attempted to overcome these challenges by testing various reformulated versions of booster insulation. The results suggest the SLS program should continue to investigate material alternatives for potential block upgrades or use an entirely new, more advanced booster. The experimental design was composed of a logic path that performs iterative formulation and testing in order to maximize the effort. A lab mixing baseline was developed and documented for the Rubber Laboratory in Bldg. 4602/Room 1178.

Chapman, Cynthia↗

NASA NTRS2021

MISSE-Flight Facility Polymers and Composites Experiment 1-4 (PCE 1-4)

Spacecraft in low Earth orbit (LEO) are subjected to harsh environmental conditions, including radiation (cosmic rays, ultraviolet (UV), x-ray and charged particle radiation), micrometeoroids and orbital debris, temperature extremes, thermal cycling, and atomic oxygen (AO). These environmental exposures can result in erosion, embrittlement and optical property degradation of susceptible materials threatening spacecraft performance and durability. To increase our understanding of effects such as AO erosion and radiation induced embrittlement of spacecraft materials, NASA Glenn Research Center has developed a series of experiments that are flown as part of the Materials International Space Station Experiment (MISSE) missions on the exterior of the International Space Station (ISS). These experiments have provided critical space environmental durability data such as AO erosion data of polymers and composites, and radiation induced mechanical property degradation of spacecraft insulation materials, after long term space exposure. In continuing these studies, four Glenn experiments have been flown on ISS’s MISSE-Flight Facility (MISSE-FF). These experiments are the Polymers and Composites Experiment-1 (PCE-1) flown as part of the inaugural MISSE-9 mission, the PCE-2 flown as part of the MISSE-10 mission, the PCE-3 being flown as part of the MISSE-12 mission, and the PCE-4 being flown as part of the MISSE-13 mission. This paper provides an overview of space environmental effects on spacecraft materials and Glenn’s PCE 1-4 MISSE-FF experiments.

Atomic oxygen↗

NASA NTRSDate not supplied

Initial Results of the MISSE-Flight Facility Polymers and Composites Experiment 1-4 (PCE 1-4)

Spacecraft in low Earth orbit (LEO) are subjected to harsh environmental conditions, including radiation (cosmic rays, ultraviolet (UV), x-ray and charged particle radiation), micrometeoroids and orbital debris, temperature extremes, thermal cycling, and atomic oxygen (AO). These environmental exposures can result in erosion, embrittlement and optical property degradation of susceptible materials threatening spacecraft performance and durability. To increase our understanding of effects such as AO erosion and radiation induced embrittlement of spacecraft materials, NASA Glenn Research Center has developed a series of experiments that are flown as part of the Materials International Space Station Experiment (MISSE) missions on the exterior of the International Space Station (ISS). These experiments have provided critical space environmental durability data such as AO erosion data of polymers and composites, and radiation induced mechanical property degradation of spacecraft insulation materials, after long term space exposure. In continuing these studies, four Glenn experiments with 365 flight samples have been flown on ISS’s external MISSE-Flight Facility (MISSE-FF). These experiments are the Polymers and Composites Experiment-1 (PCE-1) flown as part of the inaugural MISSE-9 mission, the PCE-2 flown as part of the MISSE-10 mission, the PCE-3 flown as part of the MISSE-12 and MISSE-15 missions, and the PCE-4 flown as part of the MISSE-13 mission. The primary objective of the PCE 1-4 experiments is to determine the AO and radiation durability of spacecraft polymers and composites. In addition, each experiment has a wide variety of spacecraft materials and hence they each have numerous additional sample objectives. Each of the PCE 1-4 is designed to examine the consequences of AO interactions including AO erosion yield (Ey) and optical and thermal property characterization. Several polymers were flown in both ram and zenith flight orientations to determine the effect of varying solar to AO ratios on Ey. Common spacecraft materials including Teflon FEP, white Tedlar and Upilex-S were included on multiple MISSE missions so erosion dependence on environment exposure can be determined. The PCE-1 includes epoxy composite samples with varying ZnO levels to determine the effect of inorganic filler level on AO durability. And, a variety of samples were flown to characterize AO scattering and AO undercutting processes. All four PCE experiments include samples to provide better insight into radiation durability of polymers and composites. The MISSE-9 PCE-1 includes Teflon FEP tensile samples flown in the wake and zenith direction so variations in radiation exposure from the different flight directions can provide insight into radiation induced embrittlement of Teflon FEP. Teflon FEP tensile samples were also flown in the wake direction as part of the MISSE-13 PCE-4. In addition, shape memory alloys, shape memory composites, melanin based composites, stressed and unstressed gossamer sun shield materials, coated and uncoated docking seal samples, and new solar cell cover slides were flown for space radiation durability and/or shielding assessment. This paper provides an overview of Glenn’s PCE 1-4 MISSE-FF experiments and provides initial post-flight observations and results.

atomic oxygen↗

NASA NTRS1961

ANALYSIS OF CRYOGENIC PROPELLANT FEED SYSTEMS FOR ELECTROTHERMAL ENGINES.

An analytical investigation was made of the problems associated with the long-term storage and control of flow of cryogenic propellants for electrothermal engines. Storage of 35 to 174 pounds of propellant for three years is made difficult by the high ratio of surface area to storage tank volume, and the resulting high rate of heat leak. Vented and non-vented storage, storage as high pressure gas, and the use of refrigeration were considered. Recommended storage methods are: for ethane and ammonia vented storage - by venting propellant stored in excess of mission requirements; for hydrogen and helium - by non-vented storage of cold supercritical vapor; and for methane by storage as a non-vented two-phase mixture. The optimum propellant density in the storage tank and optimum insulation thickness were also determined. Design charts were developed for hydrogen and helium, for estimating the maximum pressure expected in non-vented storage tanks, as function of mission requirements. Separation of the constituent phases of liquid-vapor mixtures is achieved by throttling the two-phase mixture to a lower pressure (and temperature) and vaporizing the liquid in the mixture by heat exchange with the contents of the storage tank. The time limitations for continuous use of this method are discussed. Linde super insulations SI-44 or SI -91 are recommended for insulation. Precooling the insulation to temperatures below the steady state level with cold helium vapor before or during fueling of the storage tank eliminates the flow of heat to the tank contents during countdown and take-off. The masses, sizes, and power requirements of the recommended systems are low. The controls are simple and reliable. From the equations and charts in this report the components of the system for a particular mission can be sized. Recommendations are given for experimental work required for the development and testing of such components.

ELECTROTHERMAL ENGINE↗

NASA NTRS1965

Low heat leak connector for cryogenic system

Heat leak from the surrounding atmosphere during fluid transfer from a spaced shell-insulated vessel for storing liquified gas having an upper gaseous phase, in minimized by forming a relatively wide, shallow blister on the wall of the vessel at the point of transfer line connection. The shell and the opposed walls of the blister have aligned openings whose common axis passes centrally through the blister and is normal to the surfaces of the vessel and shell. A fluid transfer line conduit passing through the shell opening is in fluid-tight connection with the shell and blister wall. The fluid transfer line confines the fluid in a continuous stream. The blister is filled with a heat insulating material which provides a thermal break between the central wall portions of the blister. A connector at the bottom of the vessel comprises a tube extending between the openings in the blister which projects a short distance within the body of liquefied gas and terminates in a reverse bend to prevent backflow of liquid through the pipe.

Stelts, P. D.↗

NASA NTRS1978

Chemisorption of CO on Pd particles supported on mica

A UHV technique is presented for evaluating the adsorption-desorption properties of UHV vapor-deposited metal particles supported on insulating substrates. Desorption studies of CO from particulate and continuous Pd films supported on mica were performed. The desorption results indicate that: the CO desorption energies from the deposited metals are much lower than those from bulk single crystals; two desorption states exist for the vapor-deposited films; and the lower energy desorption peak of the vapor-deposited films is coverage dependent. Possible reasons for the difference between previously reported CO desorption studies on bulk substrates and the present results are discussed.

Thomas, M.↗

NASA NTRS1988

Continuous Production Of Refractory Microballoons

Continuous process has economic and quality advantages over batch processes. Expected to produce high-quality microballoons at relatively low cost. Continuous hollow-jet process produces microballoons of refractory metal. Microballoon products made by continuous process includes inertial-confinement fusion targets, thermal insulators, lightweight composites, impact absorbers, and containers for hazardous materials.

Schilling, Christopher H.↗

NASA NTRSDate not supplied

Error Sources and Mitigation Strategies for Thermocouples Integrated in Flexible Thermal Protection System Materials

• The flexible thermal protection system (FTPS) on NASA’s Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) vehicle will be instrumented with thermocouples (TCs) to measure the in-depth thermal response during entry into Earth’s atmosphere. Accurate flight temperature measurements are critical for verifying vehicle performance and reducing thermal model uncertainties. • The TC leads are routed from the measurement location to the data acquisition system within the same FTPS layer that they are monitoring the temperature. This approach eliminates the need to put holes in the FTPS layers. However, the insulated TC leads are exposed to high temperatures and large thermal gradients. • The baseline TCs were commercially available 30 AWG Type K TCs with a binder impregnated glass braid insulation. The glass braid is rated to a maximum continuous use temperature of 482°C. LOFTID’s heat pulse will be on the order of minutes and the maximum predicted temperature beneath the outermost FTPS layers is 1350°C.

R. A. Miller↗

NASA NTRS1966

Insulated Engine, 100-Pound Thrust

The design and test results of an insulated, 100-pound thrust engine capable of delivering high performance, providing long, steady state and pulse mode endurance, and maintaining a low outside surface temperature of 4000 F, are presented. Included are descriptions of the injector designs and insulation materials investigated, plus a discussion of the thermal analysis and test results. Continuous operation in excess of 29 minutes, and start capability in excess of 4900 pulses, have been demonstrated. To allow the use of available chamber materials and coating systems under insulated conditions, the major challenge to the designer was to define an injector design that would provide gas temperatures and performance of a predetermined value. The solution was the development of an unbalanced, 8-element triplet injector having an unequal fuel distribution within each element, capable of providing a specific impulse in excess of 290 pounds at reduced wall temperatures. The design consists of a columbium chamber and nozzle utilizing a silicide coating, a columbium injector, a composite insulation system of aluminum oxide

Roth, N. R.↗

NASA NTRS1994

High temperature polymer dielectric film-wire insulation

The highlights of the program are outlined including two major accomplishments. TRW identified and demonstrated the potential of two aromatic/heterocyclic polymers to have an outstanding and superior combination of electrical, thermal, and chemical resistance properties versus state-of-the-art Kapton for spacecraft and/or aircraft dielectric insulation applications. (Supporting data is provided in tables.) Feasibility was demonstrated for supporting/enabling technologies such as ceramic coatings, continuous film casting, and conductor wire wrapping, which are designed to accelerate qualification and deployment of the new wire insulation materials for USAF systems applications during the mid- to late-1990's.

Nairus, John G.↗

NASA NTRS2010

Thermographic Methods of Detecting Insulation Voids in Large Cryogenic Tanks

Four very large (900Kgal) cryogenic liquid hydrogen and oxygen storage tanks at Kennedy Space Center's LC-39 launch pads were constructed in 1965 to support the Apollo/Saturn V Program and continue to support the Space Shuttle Program. These double-walled spherical tanks with powdered insulation in the annular region, have received minimal refurbishment or even inspection over the years. As the Shuttle Program comes to an end we now have the time to perform limited refurbishment. Thermography has been used to monitor the state of insulation as one of the four tanks was drained of cryogen and warmed to ambient temperatures. An anomalous region of insulation detected previously with thermography was confirmed by visual inspections during this period. Thermal models and a comparison of images from the cold and warm tanks suggests that the anomalous region can be detected even without cryogen in the tank. The ability to detect and correct probable insulation voids prior to filling with cryogenic fluid can provide significant cost savings by reducing commodity boil-off over many years of use.

Arens, Ellen↗

NASA NTRS1989

Unpressurized Container For Cryogenic Testing

Unpressurized cryostat makes mechanical testing of materials at low temperature more convenient. Maintains specimens at temperatures of -400 to -450 degree F without sealing them in gastight, vacuum-insulated container. Easy to insert and remove specimens and attach instrumentation wiring to them. Vents vapor continuously, so no danger of buildup of internal pressure from evaporating cryogenic liquid. Includes two concentric chambers with stainless-steel walls and fiber insulation. Specimen mounted in inner chamber, and such instruments as extensometers and thermocouples attached. Loose lid of polystyrene foam or other suitable material placed over vessel.

Walker, Susan B.↗

NASA NTRS1974

Procedure for dispersing fiber bundles

Fiber bundles are dispersed and fibers are cleaned within enclosed container; therefore, safety clothing, masks, and eye protection are not required. Procedure also could be used wherever materials, such as fiberglass or insulation, require dispersion, fluffing, or cleaning. Process could be automated into continuous operation for handling large quantities of fiber.

Padilla, D.↗

NASA NTRS1978

A facility for the simulation of environmental parameters and qualification of flight thermal coatings

There is a continuing interest and need for investigation and development of, various paints, coatings, multi-layer insulation, and electrically conductive paints and coatings used for thermal control and electrical discharge of spacecraft surfaces. Degradation of these surfaces by solar-wind energy particles and ultraviolet irradiation, as well as contamination by the outgassing of materials used in conjunction or close proximity to these surfaces, continues to be a matter of concern. The following is a description of a facility with the capability of evaluating the synergistic effects encountered in the space environment. Actual flight qualification programs are also described.

Paczkowski, F. N.↗