Analysis of Stress-rupture and Creep Properties of Tungsten Fiber Reinforced Copper Composites
Stress rupture and creep properties analyzed in tungsten fiber reinforced copper composites
REINFORCING FIBER↗
SEARCH · Engineering Papers
Results for “CREEP ANALYSIS”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Moving singularity creep crack growth analysis with the /Delta T/c and C/asterisk/ integrals
The physical meaning of (Delta T)c and its applicability to creep crack growth are reviewed. Numerical evaluation of (Delta T)c and C(asterisk) is discussed with results being given for compact specimen and strip geometries. A moving crack-tip singularity, creep crack growth simulation procedure is described and demonstrated. The results of several crack growth simulation analyses indicate that creep crack growth in 304 stainless steel occurs under essentially steady-state conditions. Based on this result, a simple methodology for predicting creep crack growth behavior is summarized.
Stonesifer, R. B.↗
Interim analysis of long time creep behavior of columbium C-103 alloy
Analysis of 16 long time creep tests on columbium C-103 alloy (Cb-10Hf-1Ti-0.7Zr) indicates that the calculated stresses to give 1 percent creep strain in 100,000 hours at 1,255 K (1800 F) are 7.93 and 8.96 MPa (1,150 and 1,300 psi) for fine grained and course grained materials, respectively. The apparent activation energy and stress dependence for creep of this alloy are approximately 315 KJ/gmol (75,300 cal/gmol) and 2.51, respectively, based on Dorn-Sherby types of relations. However, the 90 percent confidence limits on these values are wide because of the limited data currently available.
Klopp, W. D.↗
Thermal capabilities and graphical output of PAFEC
The program for automatic finite element calculations (PAFEC) developed for the computation of heat transfer in structures is discussed. The passive and interactive graphics capabilities of the PAFEC system are presented and future developments are outlined. This finite element system is shown to have significant thermal capabilities in support of its general structures. The program offers the following types of analysis: interactive graphics; user defined program control steps; steady state, transient heat transfer; boundary element methods; linear static, stress and displacements; modes and frequencies calculations; direct dynamic time intergration; frequency response analysis; elastohydrodynamic lubrication; large deflection analysis, buckling; creep and plasticity analysis; and substructures analysis.
Akin, J. E.↗
Analysis of the creep behavior of a square plate loaded in edge compression
Explore the source record for details and available documents.
Mccomb, Harvey G , Jr↗
Finite element elastic-plastic-creep and cyclic life analysis of a cowl lip
Results are presented of elastic, elastic-plastic, and elastic-plastic-creep analyses of a test-rig component of an actively cooled cowl lip. A cowl lip is part of the leading edge of an engine inlet of proposed hypersonic aircraft and is subject to severe thermal loadings and gradients during flight. Values of stresses calculated by elastic analysis are well above the yield strength of the cowl lip material. Such values are highly unrealistic, and thus elastic stress analyses are inappropriate. The inelastic (elastic-plastic and elastic-plastic-creep) analyses produce more reasonable and acceptable stress and strain distributions in the component. Finally, using the results from these analyses, predictions are made for the cyclic crack initiation life of a cowl lip. A comparison of predicted cyclic lives shows the cyclic life prediction from the elastic-plastic-creep analysis to be the lowest and, hence, most realistic.
Arya, Vinod K.↗
Finite element elastic-plastic-creep and cyclic life analysis of a cowl lip
Results are presented of elastic, elastic-plastic and elastic-plastic-creep analyses of a test-rig component of an actively cooled cowl lip. A cowl lip is part of the leading edge of an engine inlet of proposed hypersonic aircraft and is subject to severe thermal loadings and gradients during flight. Values of stresses calculated by elastic analysis are well above the yield strength of the cowl lip material. Such values are highly unrealistic, and thus elastic stress analyses are inappropriate. The inelastic (elastic-plastic and elastic-plastic-creep) analyses produce more reasonable and acceptable stress and strain distributions in the component. Finally, using the results from these analyses, predictions are made for the cyclic crack initiation life of a cowl lip. A comparison of predicted cyclic lives shows the cyclic life prediction from the elastic-plastic-creep analysis to be the lowest and, hence, most realistic.
Arya, V. K.↗
Theory of Dynamic Creep
An analysis is given of the causes of the increase in the creep of a material under dynamic loads. A theory of dynamic creep is proposed based on the after-effect theory of Becker.
THEORIES - CREEP↗
A three dimensional photoelasto-plastic stress analysis method.
Photoelastoplastic method using creep and stress characteristics of epoxy resins under thermal cycle, discussing stress-strain behavior
ELASTIC PROPERTY↗
Creep-rupture and fractographic analysis of Stirling engine superalloys tested in air and 15 MPa hydrogen
A brief comparative analytical and microstructural evaluation of creep-rupture performance of two iron-base superalloys in air and 15 MPa of hydrogen, is presented. Creep rupture data are presented for the sheet alloy 19-9DL and the cast alloy XF-818, including temperature, initial stress, rupture life, minimum creep rate, time to reach one percent creep strain, and total elongation. In 19-9DL, both rupture life and minimum creep rate are more sharply dependent on small stress changes than in XF-818 in the given environment, and 19-9DL appears to become a more creep-resistant material with increasing Q (apparent activation energy) while the opposite is noted for XF-818. There appears to be no environmental effect on minimum creep rate for 19-9DL, whereas Q becomes less negative for XF-818 for 15 MPa of H2. Multiple cracks leading to rupture are observed on the fracture surfaces, with sheet specimens showing many more cracks close to the fracture surface than cast specimens.
Bhattacharyya, S.↗
The high-temperature steady-state creep of pure silver and internally oxidized silver-magnesium alloys.
High temperature steady state creep rate analysis of pure Ag and internally ionized Ag-Mg alloys
STEADY STATE↗
A quarter-century of progress in the development of correlation and extrapolation methods for creep rupture data
Developments in the analysis of creep-rupture data are reviewed with particular reference to time temperature relations for the correlation and extrapolation of creep and stress rupture data, the minimum commitment method, and successive regression methods. Some contributions to the development of time-temperature parameters are noted.
Manson, S. S.↗
Analytical and experimental studies on creep behavior of polymeric matrix composites
The creep behavior of graphite/epoxy composites is studied both analytically and experimentally. In the analytical study, a special finite element procedure was developed for the accurate and efficient analysis of creep response in anisotropic materials. This procedure was used to study the stress and strain distributions and histories in composite laminates containing circular holes. In the experimental study, creep tests were performed to investigate the time-dependent response of graphite/epoxy composites at elevated temperature. The moire interferometry technique was employed to determine the deformation histories in notched composites. The experimental results were compared with the analytical predictions and good agreement was observed.
Lin, K. Y.↗
Creep/Stress Rupture Behavior of 3D Woven SiC/SiC Composites with Sylramic-iBN, Super Sylramic-iBN and Hi-Nicalon-S Fibers at 2700F in Air
To determine the influence of fiber types on creep durability, 3D SiC/SiC CMCs were fabricated with Sylramic-iBN, super Sylramic-iBN and Hi-Nicalon-S fibers and the composite specimens were then tested under isothermal tensile creep at 14820C at 69, 103 and 138 MPa for up to 300hrs in air. The failed specimens were examined by scanning electron microscopy (SEM) and computed tomography (CT) for fracture mode analysis. The creep data of these composites are compared with those of other SiC/SiC composites in the literature. The results of this study will be presented.
failure modes↗
Interpolation and extrapolation of creep rupture data by the minimum commitment method. II - Oblique translation
An outline is presented of a new procedure, termed the oblique translation method, which emerged in the development of the focal point convergence method. Approaches for implementing the oblique translation method are discussed. It is shown that the new method is essentially a minimum commitment method when manually-graphically implemented, in the sense that the form of the functions involved are not forced into particular analytical forms. The individual constants and functions are independently determined. The minimum commitment concept is extended to the analysis of creep rupture data wherein each isothermal is to be generated by an oblique translation of the 'master curve' when plotted. Attention is given to a manual-graphical analysis, the preassessment of data, and an analysis by computer code.
Manson, S. S.↗
Creep-Fatigue Properties of Additional 316H PM-HIP Materials Fabricated from Different Powder Compositions and Processing Routes
The process of powder metallurgy (PM) hot isostatic pressing (HIP) works by consolidating powdered materials at relatively high temperature and pressure to form near-net-shaped components. Ideally, PM-HIP production methods can reduce component lead time and improve designs for high-temperature reactors and/or microreactors. To introduce PM-HIP into Section III, Division 5 of the American Society of Mechanical Engineers Boiler and Pressure Vessel Code, it is necessary to show adequate material properties regarding creep, high-temperature low-cycle fatigue, and creep fatigue. However, prior work has shown that the creep-fatigue cycles to failure for PM-HIP 316H stainless steel are greatly reduced compared to the conventional, wrought product. This work continued creep-fatigue analysis on a 316H stainless steel with lower oxygen and nitrogen contents and at different HIP parameters than previously analyzed. The objective was to better understand what is causing the reduced PM-HIP 316H performance so improvements can be made PM-HIP 316H creep-fatigue lifetimes.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Inelastic micromechanics of curing stresses in composites
The combined finite element/laminate analysis method is used to study the thermal curing stresses in composite materials with a nonlinearly elastic matrix subject to creep. The application of this analysis to boron/epoxy composites shows that curing stress levels in the laminate are of sufficient magnitude to cause widespread yielding in the matrix. The stress levels, based on the creep analysis of a typical laminate cure cycle, indicate that the residual stresses can vary from 80 to 100% of the residual stress estimates based on linear thermoelastic analysis. It is shown that there is virtually no change in the static longitudinal or shear response of unidirectional and cross-ply boron/epoxy laminates as a result of curing stresses. Results of a series of constant-stress, high temperature creep tests are presented.
Foye, R. L.↗
Glacier and Ice Shelves Studies Using Satellite SAR Interferometry
Satellite radar interferometry is a powerful technique to measure the surface velocity and topography of glacier ice. On ice shelves, a quadruple difference technique separates tidal motion from the steady creep flow deformation of ice. The results provide a wealth of information about glacier grounding lines , mass fluxes, stability, elastic properties of ice, and tidal regime. The grounding line, which is where the glacier detaches from its bed and becomes afloat, is detected with a precision of a few tens of meters. Combining this information with satellite radar altimetry makes it possible to measure glacier discharge into the ocean and state of mass balance with greater precision than ever before, and in turn provide a significant revision of past estimates of mass balance of the Greenland and Antarctic Ice Sheets. Analysis of creep rates on floating ice permits an estimation of basal melting at the ice shelf underside. The results reveal that the action of ocean water in sub-ice-shelf cavities has been largely underestimated by oceanographic models and is the dominant mode of mass release to the ocean from an ice shelf. Precise mapping of grounding line positions also permits the detection of grounding line migration, which is a fine indicator of glacier change, independent of our knowledge of snow accumulation and ice melting. This technique has been successfully used to detect the rapid retreat of Pine Island Glacier, the largest ice stream in West Antarctica. Finally, tidal motion of ice shelves measured interferometrically provides a modern, synoptic view of the physical processes which govern the formation of tabular icebergs in the Antarctic.
Rignot, Eric↗