Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CORROSIVE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2015

Corrosion products of carbonation induced corrosion in existing reinforced concrete facades

Active corrosion in reinforced concrete structures is controlled by environmental conditions and material properties. These factors determine the corrosion rate and type of corrosion products which govern the total achieved service life. The type and critical amount of corrosion products were studied by electron microscopy and X-ray diffractometry on concrete and reinforcement samples from existing concrete facades on visually damaged locations. The corrosion products in outdoor environment exposed concrete facades are mostly hydroxides (Feroxyhite, Goethite and Lepidocrocite) with a volume ratio to Fe of approximately 3. The results can be used to calibrate calculation of the critical corrosion penetration of concrete facade panels.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Combining four-point bending and corrosion to map stress-dependent corrosion susceptibility of 316H stainless steel in FLiNaK

Understanding the effect of stress on the corrosion of steels in molten salts is important for material screening and safety assessment of molten salt reactors. We present a method that combines four-point bending with corrosion testing, enabling the mapping of corrosion susceptibility as a function of local stress from a single specimen. Guided by finite element analysis, a four-point bending setup was used to bend a 316H stainless-steel bar under controlled elastic stress during a 100-hour exposure in FLiNaK at 700 °C. Post-exposure characterization using scanning electron microscopy and energy-dispersive X-ray spectroscopy revealed a pronounced correlation between stress and corrosion. Regions under tensile stress exhibited significantly deeper attack depths and greater chromium depletion along grain boundaries, whereas compressive zones showed shallower corrosion cracks. The stress effect is attributed to stress concentration under tensile loading, which promotes chromium dissolution and crack propagation. This technique can be readily applied to other structural alloys, enabling quantitative measurement of corrosion susceptibility as a function of local stress.

316H↗
DOE OSTI2017

Revisiting the Corrosion of the Aluminum Current Collector in Lithium-Ion Batteries

The corrosion of aluminum current collectors and the oxidation of solvents at a relatively high potential have been widely investigated with an aim to stabilize the electrochemical performance of lithium-ion batteries using such components. The corrosion behavior of aluminum current collectors was revisited using a home-build high-precision electrochemical measurement system, and the impact of electrolyte components and the surface protection layer on aluminum foil was systematically studied. The electrochemical results showed that the corrosion of aluminum foil was triggered by the electrochemical oxidation of solvent molecules, like ethylene carbonate, at a relative high potential. The organic radical cations generated from the electrochemical oxidation are energetically unstable, and readily undergo a deprotonation reaction that generates protons and promote the dissolution of Al3+ from the aluminum foil. This new reaction mechanism can also shed light on the dissolution of transitional metal at high potentials.

Environmental Molecular Sciences Laboratory↗
DOE OSTI2023

Probing corrosion using a simple and versatile in situ multimodal corrosion measurement system

In this work, we have developed a unique in situ multimodal corrosion system that is capable of acquiring electrochemical data, sample imaging/visualization and hydrogen collection, simultaneously. Each of these modalities yield valuable information pertaining to the ongoing corrosion process. Combining them can yield holistic information on the role of microstructure, processing history, presence of coatings, etc., on the sequence of steps occurring during the corrosion process, and how they correlate with the acquired electrochemical data. Four materials systems, namely AA6061-T6 aluminum alloy, AZ91 magnesium alloy, galvanized DP590 steel, and pure Zn, were investigated under open circuit potential and under potentiodynamic polarization. The multimodal corrosion system was utilized to observe processes such as surface passivation and dissolution, pit and filiform corrosion initiation and propagation, and was correlated with location and magnitude of hydrogen evolution. This approach is shown to yield a truly multimodal understanding of the ongoing corrosion processes.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Assessing the interfacial corrosion mechanism of Inconel 617 in chloride molten salt corrosion using multi-modal advanced characterization techniques

The United States Department of Energy (DOE) has committed to expanding the domestic clean energy portfolio in response to the rising challenges of energy security in the wake of climate change. Accordingly, the construction of a series of Generation IV reactor technologies are being demonstrated, including sodium-cooled, small modular, and molten chloride fast reactors (MCFRs). To date, there are no fully qualified structural materials for constructing MCFRs. A number of commercial structural alloys have been considered for the construction of MCFRs, including alloys from the Inconel and Hastelloy series. Informed qualification of structural materials for the construction of MCFRs in the future can only be ensured by expanding the current fundamental knowledgebase of information pertaining to material performance under environmental stressors relevant to operation of the reactor, including corrosion susceptibility. The purpose of this investigation is to illustrate how a correlative multi-modal electron microscopy characterization approach, including the novel application of focused-ion beam 3D reconstruction capabilities, can elucidate the corrosion mechanism of a candidate structural material Inconel 617 for MCFR in NaCl-MgCl 2 eutectic salt at 700°C for 1,000 h. Evidence of intergranular corrosion, Ni and Fe dealloying, and Cr-O enrichment along the grain boundary, which most likely corresponds to Cr 2 O 3 , is a phenomenon that has been documented in other Ni-based superalloys exposed to chloride molten salt systems. Additional corrosion products, including the formation of insoluble MgAl 2 O 4 , within the porous network produced by the salt attack is a novel observation. In addition, Mo 3 Si 5 and τ 2 precipitates are detected in the alloy bulk and are dissolved by the salt. Furthermore, the lack of detection of design γ' precipitates in Inconel 617 after 1,000 h could indicate that the molten salt corrosion mechanism has indirectly induced a phase transformation of Al 2 TiNi (τ 2 ) and Ni 3 (Al,Ti) (γ’) phase. This investigation provides a comprehensive understanding of molten salt corrosion mechanisms in a complex material system such as a commercial structural alloy for applications in MCFRs.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Review of recent developments in the field of magnesium corrosion: Recent developments in Mg corrosion

This paper provides a review of recent developments in the field of Mg corrosion and puts those into context. This includes considerations of corrosion manifestations, material influences, surface treatment, anodization, coatings, inhibition, biodegradable medical applications, stress corrosion cracking, flammability, corrosion mechanisms for HP Mg, critical evaluation of corrosion mechanisms, and concluding remarks. There has been much research recently, and much research continues in this area. In conclusion, this is expected to produce significantly better, more-corrosion-resistant Mg alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructural basis for improved corrosion resistance of laser surface processed AZ31 Mg alloy

Despite their excellent strength to weight ratio, wider use of Mg alloys for light weighting applications is limited by their poor corrosion resistance, especially in chloride ion-containing environments. The present study shows improved corrosion resistance imparted by laser surface processing (LSP) of a commercial AZ31 (Mg-3Al-1Zn) alloy. Nanosecond laser processing at three different power settings was carried out on the surface of a 1 mm thick rolled AZ31 sheet. Corrosion testing based on ASTM B117 method and several other electrochemical tests indicates substantial enhancement of corrosion resistance in LSP-treated AZ31. The underlying reason behind improved corrosion resistance of LSP-AZ31 surface has been identified using a variety of characterization tools (SEM, TEM, XPS). Formation of a ~0.5 µm thick mixed metal (Mg, Al) oxide surface film together with refinement in the size and number density of Al-Mn intermetallic particles appear to be playing a major role towards improved corrosion resistance after LSP treatment of AZ31 alloy.

Jana, Saumyadeep↗
DOE OSTI2018

Decoupling the role of stress and corrosion in the intergranular cracking of noble-metal alloys

Intergranular stress-corrosion cracking (IGSCC) is a form of environmentally induced crack propagation causing premature failure of elemental metals and alloys. It is believed to require the simultaneous presence of tensile stress and corrosion; however, the exact nature of this synergy has eluded experimental identification. For noble metal alloys such as Ag–Au, IGSCC is a consequence of dealloying corrosion, forming a nanoporous gold layer that is believed to have the ability to transmit cracks into grain boundaries in un-dealloyed parent phase via a pure mechanical process. Here using atomic-scale techniques and statistical characterizations for this alloy system, we show that the separate roles of stress and anodic dissolution can be decoupled and that the apparent synergy exists owing to rapid time-dependent morphology changes at the dealloyed layer/parent phase interface. We discuss the applicability of our findings to the IGSCC of important engineering Fe- and Ni-based alloys in critical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Effects of calcium in ash on the corrosion performance of Ni-based alloys in simulated oxy-fuel environment

Increasing the efficiency of coal power plants requires raising the operating temperature above 650°C. However, coal ash can severely attack alloy materials at high temperature. For example, the corrosion rates of commercial Fe- and Ni-based alloys are generally greater than 2 mm/year at 750°C in the gas environment of oxy-fuel combustion. Thus, a critical study is needed to determine the effect of the constituents in the ash on corrosion and find an approach to reduce the corrosion rates in an ash-laden environment at high temperature. The role of CaO in the ash (typical of U.S. Western coal ash) has been investigated in laboratory exposure environments with various structural alloys. Detailed results are presented on weight change, scale thickness, internal penetration, microstructural characteristics of corrosion products, and the cracking of scales for the alloys after exposure at 750°C. The thermal stability of K3Al(SO4)3 under the environment of oxy-fuel combustion was determined by thermogravimetric analysis and differential thermal analysis. The reaction of this low melting temperature salt with the CaO-containing ash is discussed. In addition, we performed synchrotron nanobeam X-ray analysis to study the phase and chemical composition of the oxide layers on the alloy surface. Results from these studies are used to address the role of CaO in ash in the long-term corrosion performance of alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The Sporadic History of Rubidium and its Role in Corrosion of Steel Related to Nuclear Material Storage

The influence of rubidium (Rb), both in its metallic and oxidized states, on the corrosion resistance of steels has direct relevance to the storage of radioactive Kr-85 containing nuclear materials. Kr-85 undergoes a ß-decay to generate stable, metallic Rb. The literature to date is sparse, contained primarily in company reports and divisive as to whether Rb metal, or its oxides, can lead to corrosion of steel materials. In both the direct storage of Kr-85 and used nuclear fuel that will contain Kr-85, if Rb is corrosive then continual decay of the Kr-85 will generate an increasingly corrosive environment for the steel canister it is stored in. This review was written to consolidate the known data to date on Rb corrosion of steels to identify consistencies, contradictions and remaining gaps in our understanding of the Rb : steel system.

krypton, corrosion, steel, Rubidium↗
DOE OSTI2018

Corrosion Resistance and Durability of Superhydrophobic Copper Surface in Corrosive NaCl Aqueous Solution

Artificial superhydrophobic copper surfaces play an important role in modern applications such as self-cleaning and dropwise condensation; however, corrosion resistance and durability often present as major concerns in such applications. In this study, the anti-corrosion properties and mechanical durability of superhydrophobic copper surface have been investigated. The superhydrophobic copper surfaces were achieved with wet chemical etching and an immersion method to reduce the complexity of the fabrication process. The surface structures and materials were characterized using scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX), and Fourier transform infrared spectrometer (FTIR). The corrosion resistance and mechanical properties of the superhydrophobic copper surface were characterized after immersing surfaces in a 3.5 wt % NaCl solution. The chemical stability of the superhydrophobic copper surface in the NaCl solution for a short period of time was also evaluated. An abrasion test and an ultrasound oscillation were conducted to confirm that the copper surface contained durable superhydrophobic properties. In addition, an atomic force microscope was employed to study the surface mechanical property in the corrosion conditions. The present study shows that the resulting superhydrophobic copper surface exhibit enhanced corrosion resistance and durability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Grain boundary selective oxidation and intergranular stress corrosion crack growth of high-purity nickel binary alloys in high-temperature hydrogenated water

The effects of alloying elements in Ni-5at%X binary alloys on intergranular (IG) corrosion and stress corrosion cracking (SCC) have been assessed in 300-360°C hydrogenated water at the Ni/NiO stability line. Alloys with Cr or Al additions exhibited grain boundary oxidation and IGSCC, while localized degradation was not observed for pure Ni, Ni-Cu or Ni-Fe alloys. Environment-enhanced crack growth was determined by comparing the response in water and N2 gas. Results demonstrate that selective grain boundary oxidation of Cr and Al promoted IGSCC of these Ni alloys in hydrogenated water.

Environmental Molecular Sciences Laboratory↗
DOE OSTI2022

Pitting Corrosion in 316L Stainless Steel Fabricated by Laser Powder Bed Fusion Additive Manufacturing: A Review and Perspective

Abstract 316L stainless steel (316L SS) is a flagship material for structural applications in corrosive environments, having been extensively studied for decades for its favorable balance between mechanical and corrosion properties. More recently, 316L SS has also proven to have excellent printability when parts are produced with additive manufacturing techniques, notably laser powder bed fusion (LPBF). Because of the harsh thermo-mechanical cycles experienced during rapid solidification and cooling, LPBF processing tends to generate unique microstructures. Strong heterogeneities can be found inside grains, including trapped elements, nano-inclusions, and a high density of dislocations that form the so-called cellular structure. Interestingly, LPBF 316L SS not only exhibits better mechanical properties than its conventionally processed counterpart, but it also usually offers much higher resistance to pitting in chloride solutions. Unfortunately, the complexity of the LPBF microstructures, in addition to process-induced defects, such as porosity and surface roughness, have slowed progress toward linking specific microstructural features to corrosion susceptibility and complicated the development of calibrated simulations of pitting phenomena. The first part of this article is dedicated to an in-depth review of the microstructures found in LPBF 316L SS and their potential effects on the corrosion properties, with an emphasis on pitting resistance. The second part offers a perspective of some relevant modeling techniques available to simulate the corrosion of LPBF 316L SS, including current challenges that should be overcome.

Voisin, T. (ORCID:0000000287462659)↗
DOE OSTI2021

Mechanistic insights into selective oxidation and corrosion of multi-principal element alloys from high resolution and in situ microscopy

Multiple principal elements alloys (MPEAs) have drawn significant recent interest from the metallurgical research community. These novel alloys have the potential to replace traditional alloys with a range of tailored mechanical properties, corrosion resistance, and radiation tolerance enabled by complex compositions. The broad alloy design space of MPEAs presents a great opportunity to discover new forms of oxidation and corrosion resistance in extreme environments that break away from conventional corrosion resistant alloy design criteria. However, understanding the oxidation and corrosion response of MPEAs can be a challenging task due the complex composition, structural, and chemical state changes occurring in the corrosion product and at its interface with the base alloy. This perspective discusses the utility of high resolution and in situ microscopy techniques for revealing unique aspects of MPEA oxidation behavior at the near-atomic level. Challenges of studying these alloys and several open questions are presented.

Kautz, Elizabeth J.↗
DOE OSTI2015

High Chrome Refractory Characterization: Part I. Impact of Melt Reduction/Oxidation on the Corrosion Mechanism

High Cr 2 O 3 containing Monofrax ™ K‐3 is a robust refractory that is used in the fiberglass industry and used in radioactive waste glass melters worldwide. Monofrax ™ K‐3 is tolerant of transition metal oxides but contains highly reduced solid solutions of spinels, that is, (Mg,Fe 2+ )(Al,Cr) 2 O 3 . Conversely, many of the waste feeds being processed are highly oxidizing. The K‐3 refractory corrosion was tested in sealed crucibles starting with slurried melter feed instead of prereacted glass called for by ASTM C621. Testing the refractory coupon during the feed‐to‐glass conversion exposes the refractory to the oxidizing and reducing species being released during vitrification, for example, NO 3 − , NO 2 − , CO 2 , CO , O 2 . Corrosion rates measured in highly oxidizing (high nitrate) feeds were ~1.8–2.8 times higher than those determined using prereacted glass or reduced feeds. Confirmatory corrosion rates were measured on Monofrax ™ K‐3 coupons immersed in oxidizing feed in a 1/100th‐scale HLW pilot‐scale melter. Corrosion is heterogeneous or incongruent as Ni and Fe in the waste glass exchange with Mg and Al in the refractory. An insoluble NiFe 2 O 4 spinel corrosion product is formed that can build up a protective layer along the refractory walls or spall and settle to the melter floor depending on melt pool convection/agitation.

Jantzen, Carol M.↗