SEARCH · Engineering Papers
Results for “COPROCESSING”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Activated carbons from coal/pitch and polyethylene terephthalate blends for the removal of phenols from aqueous solutions
Blends of two bituminous coals and a coal-tar pitch (CTP) with polyethylene terephthalate (PET) were evaluated as precursors of activated carbons (ACs). The intensity of the interactions between the raw materials, coal/CTP and PET during copyrolysis was closely observed by means of thermogravimetric analysis. In addition, the homogeneity of the carbon matrix of the chars produced at 800{sup o}C in a horizontal oven was studied by polarized light optical microscopy. Activated carbons were prepared from single components and their blends (1:1 w/w) by subjecting them to carbonization up to 800{sup o}C in a horizontal oven and then activation with steam at 800{sup o}C to 50% burnoff. The porous structure of the ACs was determined by sorption of N{sub 2} at 77 K and of CO{sub 2} at 273 K. The PET-containing blends produced microporous activated carbons with a maximum BET surface area of nearly 1100 m{sup 2} g{sup -1} and a maximum micropore size distribution of 0.6-0.8 nm in the case of the AC from the CTP/PET blend. The addition of PET to a bituminous coal was compared with the preoxidation of coal P in air as a way to reduce thermoplasticity and to promote the development of the porous structure. The modification of bituminous coals by PET appeared to be more effective than conventional coal preoxidation treatment. The resultant ACs were tested by measuring their effectiveness in removing phenols from an aqueous solution. The adsorption of p-chlorophenol (PCP) by the ACs prepared from the PET-containing blends was slightly higher than for the commercial activated carbon. The ability to adsorb PCP was found to be related to the volume of the super-micropores.
Crystallization of synthetic coal-petcoke slag mixtures simulating those encountered in entrained bed slagging gasifiers
Commercial entrained bed slagging gasifiers use a carbon feedstock of coal, petcoke, or combinations of them to produce CO and H{sub 2}. These carbon sources contain mineral impurities that liquefy during gasification and flow down the gasification sidewall, interacting with the refractory linear and solidifying in the cooler zones of the gasifier. Proper slag flow is critical to good gasifier operation. A hot-stage confocal scanning laser microscope (CSLM) was used to analyze the kinetic behavior of slag crystallization for a range of synthetic coal-petcoke mixtures. On the basis of the observed precipitation during cool down studies in the 1200-1700{sup o}C temperature range, a time-temperature-transformation (TTT) diagram was created. The crystallization studies were conducted with a CO/CO{sub 2} (=1.8) corresponding to a gasification PO{sub 2} of approximately 10-8 atm at 1500{sup o}C. Ash chemistries were chosen such that they correspond to coal-petcoke feedstock mixtures with coal ash amounts of 0, 10, 30, 50, 70, and 100% (by weight), with the balance being petcoke ash. The TTT diagram exhibited two crystallization areas, one above and one below 1350{sup o}C. At the nose of the higher temperature curves, karelianite (V{sub 2}O{sub 3}) crystallization occurred and was fastest for a 30% coal-petcoke ash mixture. The second nose was located below 1350{sup o}C and had spinel-type phases that formed at 1200{sup o}C, in which preferred atomic occupation at the octahedral and tetrahedral sites varied depending upon the ash composition. At 1200{sup o}C, an Al-rich spinel formed for 100% coal slag and a Fe-rich spinel formed in petcoke-enriched slags. The addition of petcoke ash to coal ash promoted crystallization in the slag, with additional crystalline phases, such as V-rich spinel, forming at the lower temperatures. These phases were not predicted using commercially available databases. 30 refs., 18 figs.
Rheological study of comingled biomass and coal slurries with hydrothermal pretreatment
Gasification of comingled biomass and coal feedstock is an effective means of reducing the net life cycle greenhouse gas emissions in the coal gasification process while maintaining its inherent benefits of abundance and high-energy density. However, feeding a comingled biomass and coal feedstock into a pressurized gasification reactor poses a technical problem. Conventional dry feeding systems, such as lock hoppers and pressurized pneumatic transport, are complex and operationally expensive. A slurry formation of comingled biomass and coal feedstock can be easily fed into the gasification reactor but, in normal conditions, only allows for a small portion of biomass in the mixture. This is a consequence of the hydroscopic and hydrophilic nature of the biomass. The College of Engineering Center for Environmental Research and Technology (CE-CERT) at the University of California, Riverside, has developed a process producing high solid content biomass-water slurry using a hydrothermal pretreatment process. In this paper, the systematic investigation of the rheological properties (e.g., shear rate, shear stress, and viscosity) of coal-water slurries, biomass-water slurries, and comingled biomass and coal-water slurries is reported. The solid particle size distribution in the slurry and the initial solid/water ratio were investigated to determine the impact on shear rate and viscosity. This was determined using a rotational rheometer. The experimental results show that larger particle size offers better pumpability. The presence of a high percentage of biomass in solid form significantly decreases slurry pumpability. It is also shown that the solid loading of the biomass-water slurry can be increased to approximately 35 wt % with viscosity of less than 0.7 Pa.s after the pretreatment process. The solid loading increased to approximately 45 wt % when the biomass is comingled with coal. 18 refs., 7 figs., 3 tabs.
Model for cradle-to-gate life cycle assessment of clinker production
A model for input- and technology-dependent cradle-to-gate life cycle assessments (LCA) was constructed to quantify emissions and resource consumption of various clinker production options. The model was compiled using data of more than 100 clinker production lines and complemented with literature data and best judgment from experts. It can be applied by the cement industry for the selection of alternative fuels and raw materials (AFR) and by authorities for decision-support regarding the permission of waste co-processing in cement kilns. In the field of sustainable construction, the model can be used to compare clinker production options. Two case studies are presented. First, co-processing of four different types of waste is analyzed at a modern precalciner kiln system. Second, clinker production is compared between five kiln systems. Results show that the use of waste (tires, prepared industrial waste, dried sewage sludge, blast furnace slag) led to reduced greenhouse gas emissions, decreased resource consumption, and mostly to reduced aggregated environmental impacts. Regarding the different kiln systems, the environmental impact generally increased with decreasing energy efficiency. 35 refs., 2 figs., 2 tabs.
Co-production of decarbonized synfuels and electricity from coal + biomass with CO{sub 2} capture and storage: an Illinois case study
Energy, carbon, and economic performances are estimated for facilities co-producing Fischer-Tropsch Liquid (FTL) fuels and electricity from a co-feed of biomass and coal in Illinois, with capture and storage of by-product CO{sub 2}. The estimates include detailed modeling of supply systems for corn stover or mixed prairie grasses (MPG) and of feedstock conversion facilities. Biomass feedstock costs in Illinois (delivered at a rate of one million tonnes per year, dry basis) are $ 3.8/GJ{sub HHV} for corn stover and $ 7.2/GJ{sub HHV} for MPG. Under a strong carbon mitigation policy, the economics of co-producing low-carbon fuels and electricity from a co-feed of biomass and coal in Illinois are promising. An extrapolation to the United States of the results for Illinois suggests that nationally significant amounts of low-carbon fuels and electricity could be produced this way.
Co-liquefaction of the Elbistan Lignite and Poplar Sawdust. Part I: The Effect of the Liquefaction Parameters
In this study, the liquefaction of Elbistan lignite and poplar sawdust, and the co-liquefaction of the Elbistan lignite and the poplar sawdust in an inert atmosphere and in non-catalytic conditions have been examined. Also, the effects of solvent/coal ratio and stirring speed on the total conversion derived as the result of the liquefaction process was attempted to be determined. Based on the results, although the effects of the solvent/coal ratio and the stirring speed on total conversion are similar for both the Elbistan lignite and the poplar sawdust, it was also noted that, under similar conditions, the conversion for the poplar sawdust was higher, as compared to the conversion of the Elbistan lignite. As the result of the liquefaction of Elbistan lignite and poplar sawdust under inert atmospheric conditions, the total conversion was increased partially, depending on both solvent/coal ratio and the speed of stirring. However, it was also noted that the total conversion did not change to a significant extent in high solvent/coal ratios and in stirring speed. As the result of the co-liquefaction of the Elbistan lignite and poplar sawdust under inert atmospheric conditions, total conversion was increased, based on the solvent/coal ratio. However, as in the case of the liquefaction of Elbistan lignite and poplar sawdust, it was noted that the high solvent/coal ratios (i.e., solvent/coal ratios of higher than 2/1) did not have a significant effect on the total conversion that was derived as the result of the co-liquefaction of the Elbistan lignite and poplar sawdust.
Non-isothermal kinetic studies of co-combustion and co-cracking of coal and plastic blends using thermogravimetric analysis
The kinetics of co-combustion/co-cracking of Topa coal with polystyrene, poly(vinyl chloride), and bakelite have been studied by theromogravimetric analysis at a linear heating rate of 20C/min in a stream of air for combustion and in nitrogen for cracking with a flow rate of 20 cm{sup 3}/min up to the temperature of 900C under non-isothermal conditions. The order of reaction and overall activation energy of the reactions have been calculated. These studies may help in synergistic production of value-added organic compounds and spatiality chemicals from coal and plastics.
Modification of coal tar pitch by high-temperature treatment with polyvinyl chloride
Properties of residues from joint pyrolysis of poly(vinyl chloride) and coal tar pitch at 300 and 400{sup o}C were studied.
Pilot-Scale Biorefinery: Sustainable Transport Fuels from Biomass and Algal Residues via Integrated Pyrolysis, Catalytic Hydroconversion and Co-processing with Vacuum Gas Oil
Beginning in 2010, UOP, along with the Department of Energy and other project partners, designed a pathway for an integrated biorefinery to process solid biomass into transportation fuel blendstocks. The integrated biorefinery (IBR) would convert second generation feedstocks into pyrolysis oil which would then be upgraded into fuel blendstocks without the limitations of traditional biofuels.
Catalytic Fast Pyrolysis Oil Stand-Alone and Co-Hydroprocessing Case Studies: Design, Cost, and Sustainability Based on Process Model Predictions
Refined liquid fuels provide conveniences for road, rail, air, and marine transportation due to high energy density, ease of transport and storage, and existing production and distribution infrastructure. Biomass conversion technologies can help diversify and increase the supply of liquid fuels towards a more robust energy future. The backbone of such development must include reliable, high-volume biomass supply chains and efficient utilization of those resources. These activities, if pursued, will lead to rural infrastructure development and new jobs.
Application of thermogravimetric analysis to study the thermal degradation of solid and liquid organic wastes
In this work, the thermolysis of composite binary mixtures of refinery or coal-processing waste with waste biomass and D-grade (long-flame) coal was analyzed in order to increase the efficiency of the cothermolysis of chemically different organic wastes mainly because of the synergism of the thermolysis of mixture components and, correspondingly, the selectivity of formation of high-quality by-products (solid, gaseous, or liquid). A new approach to the analysis of thermogravimetric data was proposed and developed as applied to complex binary mixtures of carbon-containing materials. This approach was based on (1) the preliminary separation of the thermal degradation of individual carbon-containing mixture components into individual structural constituents and (2) the monitoring of the conversion of each particular structure fragment as a constituent of the mixtures in the course of the cothermolysis of the mixtures of starting components. Based on the approach developed, data on the main synergism effects in the course of cothermolysis in the binary test systems were obtained: the temperature regions of the appearance of these effects were distinguished, the main conclusions were made with respect to particular structure fragments in complex organic wastes responsible for the interaction of components in composite systems, and the directions (positive or negative) of changes in the yields of solid by-products and the degrees of effects (difference between the yields of cothermolysis by-products in each particular region of the appearance of synergistic effects in the systems) were determined. Additionally, the influence of alkali metal carbonate additives on synergistic effects in the interaction between binary system components under the process conditions of cothermolysis was analyzed.
Characterization of liquids derived from laboratory coking of decant oil and co-coking of Pittsburgh seam bituminous coal with decant oil
In this study, decant oil and a blend of Pittsburgh seam bituminous coal with decant oil were subjected to coking and co-coking in a laboratory-scale delayed coker. Higher yields of coke and gas were obtained from co-coking than from coking. Coal addition into the feedstock resulted in lighter overhead liquid. GC/MS analyses of gasoline, jet fuel, and diesel show that co-coking of coal/decant oil gave higher quantity aromatic components than that of coking of decant oil alone. Simulated distillation gas chromatography analyses of overhead liquids and GC/MS analyses of vacuum fractions show that when coal was reacted with a decant oil, the coal constituents contributed to the distillable liquids. To address the reproducibility of the liquid products, overhead liquid samples collected at the first, third, and fifth hours of experiments of 6 h duration were evaluated using simulated distillation gas chromatography and {sup 1}H and {sup 13}C NMR. NMR analyses of the liquid products showed that, even though there were slight changes in the {sup 1}H and {sup 13}C spectra, the standard deviation was low for the time-dependent samples. Simulated distillation gas chromatography showed that the yields of refinery boiling range materials (i.e., gasoline, jet fuel, diesel, and fuel oil cuts) were reproducible between runs. Fractionation of the overhead liquids into refinery boiling range materials (gasoline, jet fuel, diesel, fuel oil fractions) showed that the boiling range materials and chemical compositions of fractions were found to be reproducible. 54 refs., 17 tabs.
A preliminary user-friendly, digital console for the control room parameters supervision in old-generation Nuclear Plants
Improvements in the awareness of a system status is an essential requirement to achieve safety in every kind of plant. In particular, in the case of Nuclear Power Plants (NPPs), a progress is crucial to enhance the Human Machine Interface (HMI) in order to optimize monitoring and analyzing processes of NPP operational states. Firstly, as old-fashioned plants are concerned, an upgrading of the whole console instrumentation is desirable in order to replace an analog visualization with a full-digital system. In this work, we present a novel instrument able to interface the control console of a nuclear reactor, developed by using CompactRio, a National Instruments embedded architecture and its dedicated programming language. This real-time industrial controller composed by a real-time processor and FPGA modules has been programmed to visualize the parameters coming from the reactor, and to storage and reproduce significant conditions anytime. This choice has been made on the basis of the FPGA properties: high reliability, determinism, true parallelism and re-configurability, achieved by a simple programming method, based on LabVIEW real-time environment. The system architecture exploits the FPGA capabilities of implementing custom timing and triggering, hardware-based analysis and co-processing, and highest performance control algorithms. Data stored during the supervisory phase can be reproduced by loading data from a measurement file, re-enacting worthwhile operations or conditions. The system has been thought to be used in three different modes, namely Log File Mode, Supervisory Mode and Simulation Mode. The proposed system can be considered as a first step to develop a more complete Decision Support System (DSS): indeed this work is part of a wider project that includes the elaboration of intelligent agents and meta-theory approaches. A synoptic has been created to monitor every kind of action on the plant through an intuitive sight. Furthermore, another important aim of this work is the possibility to have a front panel available on a web interface: CompactRio acts as a remote server and it is accessible on a dedicated LAN. This supervisory system has been tested and validated on the basis of the real control console for the 1-MW TRIGA reactor RC-1 at the ENEA, Casaccia Research Center. In this paper we show some results obtained by recording each variable as the reactor reaches its maximum level of power. The choice of a research reactor for testing the developed system relies on its training and didactic importance for the education of plant operators: in this context a digital instrument can offer a better user-friendly tool for learning and training. It is worthwhile to remark that such a system does not interfere with the console instrumentation, the latter continuing to preserve the total control. (authors)