Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CHROMIUM 42”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Advanced heat exchanger development for molten salts

This study addresses present work concerned with advanced heat exchanger development for molten salt in nuclear and non nuclear thermal systems. The molten salt systems discussed herein use alloys, such as Hastelloy N and 242, which show corrosion resistance to molten salt at nominal operating temperatures up to 700°C. These alloys were diffusion welded, and the corresponding information is presented. Test specimens were prepared for exposing diffusion welds to molten salt environments. Hastelloy N and 242 were found to be weldable by diffusion welding, with ultimate tensile strengths about 90% of base metal values. Both diffusion welds and sheet material in Hastelloy N were corrosion tested in?58 mol% KF and 42 mol% ZrF4 at 650, 700, and 850°C for 200, 500, and 1,000 hours. Corrosion rates found were similar between welded and nonwelded materials, typically <10 mils per year. For materials of construction, nickel and alloys with dense nickel coatings are effectively inert to corrosion in fluorides, but not so in chlorides. Hence, additional testing of selected alloys for resistance to intergranular corrosion is needed, as is a determination of corrosion rate as a function of contaminant type and alloy composition with respect to chromium and carbon to better define the optimal chromium and carbon composition, independent of galvanic or differential solubility effects. Also presented is the division of the nuclear reactor and high temperature components per ASME standards, along with design requirements for a subcritical Rankine power cycle heat exchanger that has to overcome pressure difference of about 17 MPa.

42 ENGINEERING↗

Cr-free Fe-based metal oxide catalysts for high temperature water gas shift reaction of fuel processor using LPG

The goal of this study was to identify the most suitable chromium-free iron-based catalysts for the HTS (high temperature shift) reaction of a fuel processor using LPG. Hexavalent chromium (Cr6+) in the commercial HTS catalyst has been regarded as hazardous material. We selected Ni and Co as the substitution for chromium in the Fe-based HTS catalyst and investigated the HTS activities of these Crfree catalysts at LPG reformate condition. Cr-free Fe-based catalysts which contain Ni, Zn, or Co instead of Cr were prepared by coprecipitation method and the performance of the catalysts in HTS was evaluated under gas mixture conditions (42% H2, 10% CO, 37% H2O, 8% CO2, and 3% CH4; R (reduction factor): about 1.2) similar to the gases from steam reforming of LPG (100% conversion at steam/carbon ratio = 3), which is higher than R (under 1) of typically studied LNG reformate condition. Among the prepared Cr-free Febased catalysts, the 5 wt%-Co/Fe/20 wt%-Ni and 5 wt%-Zn/Fe/20 wt%-Ni catalysts showed good catalytic activity under this reaction condition simulating LPG reformate gas.

02 PETROLEUM↗

Effect of Nickel on the Adhesion and Corrosion Ability of Pseudomonas aeruginosa on Stainless Steel

Microbial colonization of metal surfaces or adhesion of bacteria on metal surfaces is a crucial step in initiating microbiologically influenced corrosion. As the substrate is essential in the development of a biofilm, an understanding of how substrate properties affect adhesion of bacterial cells, including the mechanism of bacterial adhesion, may assist in designing or modifying substrates to inhibit bacterial adhesion and prevent the corrosion of materials. A study was carried out to investigate the effect of nickel on the adhesion and corrosion ability of stainless steels with the same chromium content in nutrient-rich simulated seawater containing Pseudomonas aeruginosa. These stainless steels were 201, 316, 304 and 430 stainless steels. In addition, a carbon steel sample with fully nickel coated was included for comparison. The hydrophobicity of different materials was evaluated by measuring the contact angles made by the water, glycerol and formaldehyde. The number of bacteria adhering to the material surface after short-term immersion was counted by fluorescence microscopy. For corrosion study, the corrosion rates and pitting morphology were studied after 42 days of immersion. The corrosion behavior of the samples was also observed by scanning electron microscope (SEM) coupled with energy-dispersive x-ray spectroscopy (EDX) and inductively coupled plasma mass spectrometry (ICPMS). It was found that the nickel-coated sample had the highest level of bacteria attachment and offered poor corrosion resistance under artificial seawater with Pseudomonas aeruginosa strain. Higher nickel content in stainless steel resulted in a higher level of bacteria attachment. It was found that stainless steel with molybdenum exhibited better corrosion resistance in artificial seawater containing bacteria.

36 MATERIALS SCIENCE↗

Crystal Structure, Magnetic and Electrical Properties of Half-Doped Chromium Manganite La{sub 0.5}Sr{sub 0.5}Mn{sub 0.5}Cr{sub 0.5}O{sub 3}

Polycrystalline sample La{sub 0.5}Sr{sub 0.5}Mn{sub 0.5}Cr{sub 0.5}O{sub 3} (LSMCO) was prepared by a conventional solid-state reaction method in the air, and its structure was determined by Rietveld refinement using consistent resolution time-of-flight X-ray diffraction. Different structural models have been used for analysis of X-ray diffraction data recorded at room temperature, but the best fits have been found using a mixture of rhombohedral and an orthorhombic structural phases (42(1)%/57(1)%). The rhombohedral, centro-symmetric space group R 3-bar c(No.167,a≈√2a{sub p},c≈2√3a{sub p},Z=6) with octahedral tilting scheme a{sup −}a{sup −}a{sup −} leading to a three identical out-of-phase tilt angle of (Mn/Cr)-O{sub 6} octahedron along three perovskite main directions: x, y, and z-axes. The orthorhombic space group Pbnm(No.62,a≈b≈√2a{sub p},c≈2a{sub p},Z=4) with octahedral tilting scheme a{sup −}a{sup −}c{sup +}, leads to an anti-phase tilts of the same magnitude about [100] and [010] directions of the elementary specimen cell and in-phase tilt of different magnitude about the [001] direction. At low temperature 10 K, Rietveld refinement of powder diffraction data revealed that the crystal structure of sample is distorted with a single orthorhombic symmetry (space group Pbnm). Magnetic measurements indicate that our investigated sample exhibits an overall anti-ferromagnetic behavior mainly attributed to the frustration induced by both competing AFM Cr{sup 3+}-O-Cr{sup 3+}, Mn{sup 4+}-O-Mn{sup 4+} networks, and the mixed one Mn{sup 4+}-O-Cr{sup 3+}exchange magnetic interactions. The temperature dependence of the resistivity measured under zero field shows a semi-conducting behavior in the whole temperature range, which probably could be described by the adiabatic small polaron hoping model with relatively high polaron activation energy.

36 MATERIALS SCIENCE↗

Comparison of T{sub z} = {+-}1{yields}0 GT Transitions

Gamow-Teller (GT) transitions can be studied in both {beta}-decay and charge exchange(CE) reactions. If isospin is a good quantum number, then the T{sub z} = -1{yields}0 and T{sub z} = +1{yields}0 GT mirror transitions, are identical. Therefore, a comparison of the results from studies of {beta} decay and CE should shed light on this assumption. Accordingly we have studied the {beta} decay of the T{sub z=-1} fp-shell nuclei, {sup 54}Ni, {sup 50}Fe, {sup 46}Cr, and {sup 42}Ti, produced in fragmentation and we have compared our results with the spectra from ({sup 3}He, t) measurements on the mirror T{sub z} = +1 target nuclei studied in high resolution at RCNP, Osaka. The {beta}-decay experiments were performed as part of the STOPPED beam RISING campaign at GSI.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Comparison of T{sub z} = +-1->0 GT Transitions Studied in beta--decay and CE Reactions

Gamow-Teller (GT) transitions can be studied in both beta- decay and charge exchange(CE) reactions. If isospin is a good quantum number, then the T{sub z} = -1->0 and T{sub z} = +1->0 GT mirror transitions, are identical. Therefore, a comparison of the results from studies of beta decay and CE should shed light on this assumption. Accordingly we have studied the beta decay of the T{sub z} = -1 fp-shell nuclei, {sup 54}Ni, {sup 50}Fe, {sup 46}Cr, and {sup 42}Ti, produced in fragmentation and we have compared our results with the spectra from (3He, t) measurements on the mirror T{sub z} = +1 target nuclei studied in high resolution at RCNP, Osaka. The experiments were performed as part of the STOPPED beam RISING campaign at GSI.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

A novel pillar indentation splitting test for measuring fracture toughness of thin ceramic coatings

Fracture toughness is an important material property that plays a role in determining the in-service mechanical performance and adhesion of thin ceramic films. Unfortunately, measuring thin film fracture toughness is affected by influences from the substrate and the large residual stresses that can exist in the films. In this paper, we explore a promising new technique that potentially overcomes these problems based on nanoindentation testing of micro-pillars produced by focused ion beam milling of the films. By making the pillar diameter approximately equal to its length, the residual stress in the pillar’s upper portion is almost fully relaxed, and when indented with a sharp Berkovich indenter, the pillars fracture by splitting at reproducible loads that are readily quantified by a sudden displacement excursion in the load displacement behavior. Cohesive finite element simulations are used to analyze and develop, for a given material, a simple relation between the critical load at failure, pillar radius, and fracture toughness. The main novel aspect of this work is that neither crack geometries nor crack sizes need to be measured post test. Furthermore, the residual stress can be measured at the same time with toughness, by comparing the indentation results from the stress-free pillars and the as-deposited film. The method is tested on three different hard coatings formed by physical vapor deposition: titanium nitride, chromium nitride, and a CrAlN/Si 3 N 4 nanocomposite. Results compare well to independently measured values of fracture toughness for the three brittle films. The technique offers several benefits over existing methods.

42 ENGINEERING↗

Accelerating effects of galvanic corrosion and dissimilar materials on the corrosion of 316H in NaCl-MgCl2 salt

Corrosion of materials presents a significant challenge for the long-term operation of molten salt reactors. This study aims to identify the most effective techniques for evaluating the corrosion performance of materials in molten salts, with a focus on the effects of galvanic corrosion and dissimilar materials. A reliable testing methodology for assessing material corrosion in molten chloride salts has been successfully developed. The corrosion of Alloy 316H in molten NaCl-MgCl2 salt was found to be significantly accelerated by galvanic corrosion. Additionally, the presence of dissimilar materials resulted in a slight increase in the corrosion rate of Alloy 316H in NaCl-MgCl2 salt. Microstructural characterization was utilized to understand the corrosion behavior of test samples under different conditions. Common trends observed across samples include chromium depletion and iron enrichment near corroded surfaces. Molybdenum enrichment along grain boundaries and corrosion surfaces was also frequently noted.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effect of Microstructural Bands on the Localized Corrosion of Laser Surface-melted 316L Stainless Steel

The localized corrosion of laser surface melted (LSM) 316L stainless steel is investigated by a combination of potentiodynamic anodic polarization in 0.1M HCl and microscopic investigation of the initiation and propagation of localized corrosion. The pitting potential of LSM 316L is significantly lower than the pitting potential of wrought 316L. The LSM microstructure is highly banded as a consequence of the high laser power density and high linear energy density. The bands are composed of zones of changing modes of solidification, cycling between very narrow regions of primary austenite solidification and very wide regions of primary ferrite solidification. Pits initiate in the outer edge of each band where the mode of solidification is primary austenite plane front solidification and primary austenite cellular solidification. The primary austenite regions have low chromium concentration (and possibly low molybdenum concentration), which explains their susceptibility to pitting corrosion. The ferrite is enriched in chromium, which explains the absence of pitting in the primary ferrite regions. The presence of the low chromium regions of primary austenite solidification explains the lower pitting resistance of LSM 316L relative to wrought 316L. The influence of banding on localized corrosion is applicable to other rapidly solidified processes such as additive manufacturing.

36 MATERIALS SCIENCE↗

Incorporation of trace metals in Hanford waste boehmite mineral phases and dissolution rate impacts

Abstract Data from radioactive Hanford tank waste samples was analyzed to assess whether trace metals present were incorporated into the bulk boehmite matrix or were simply intermingled with the bulk material and subsequent impacts to the boehmite dissolution rate. Results suggest that chromium is primarily blended into the bulk boehmite, with a small fraction present on the surface of the solids. However, increasing the level of chromium incorporation 30‐fold decreased the dissolution rate of boehmite by only 8%, suggesting incorporation of chromium into these samples had a minimal impact on the dissolution rate. Iron was also found to be incorporated in the boehmite solids. Silicon appears to be simply intermingled and not blended into the boehmite crystals.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Fiscal Year 2022. Filtration of Hanford Tank 241-AP-101 Supernatant at 16 °C

Bench-scale filtration testing of ~9 liters of supernatant from Hanford waste tank 241-AP-101, chilled to 16 °C, was conducted using a backpulse dead-end filter (BDEF) filtration system equipped with a feed vessel and a Mott inline filter Model 6610 (Media Grade 5) in the hot cells of the Radiochemical Processing Laboratory at Pacific Northwest National Laboratory. This was done to assess the performance of the anticipated third feed to the Tank Side Cesium Removal (TSCR) system. The as-received samples were diluted to the target sodium concentration and transferred to 1.5-liter polyethylene bottles and held at 16 °C for approximately 1 week prior to filtration. The feed was filtered through the BDEF system at a targeted flux of 0.065 gpm/ft 2 to match the prototypic operation of the TSCR system. During filtration, the differential pressure required to effect filtration at 0.065 gpm/ft 2 increased little over the filtration campaign and never reached 2 psid (the TSCR action limit). This indicates that the TSCR filter should perform well when processing AP-101 supernatant. After completing filtration of the AP-101 feed, the filter was cleaned. Solids concentrated from the backpulse solutions displayed sodium nitrate-type phases, aluminum and silicon phases reported as cancrinite or nitrate-cancrinite, a mixed chromium-aluminum oxide, iron oxides, and Ca-bearing phases (calcite). Scanning electron microscopy analyses showed that the average particle size was 0.5 micron.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Synthesis, structures and magnetic properties of pseudo-hollandite chromium sulfides

The pseudo-hollandite chromium sulfides, ACr{sub 5}S{sub 8} (A=K, Rb, Cs) and A'{sub 0.5}Cr{sub 5}S{sub 8} (A'=Sr, Ba), have been synthesized and investigated in structural and magnetic properties. All the compounds crystallize in the isostructure with a monoclinic C2/m. Its crystal structure has triangular lattices and double chains made of Cr{sup 3+} (d{sup 3}; S=3/2) triangles. The magnetic susceptibilities of all compounds behave as Curie-Weiss types in high temperature region. From magnetic susceptibility and specific heat measurements, all the compounds have antiferromagnetic ground states. The Neel temperatures are rather low compared to Weiss temperatures, reflecting magnetic frustration in the triangular lattices and double chains. The magnetic transitions in KCr{sub 5}S{sub 8} and Ba{sub 0.5}Cr{sub 5}S{sub 8} are a two-step transition around 50 and 60 K, respectively, while RbCr{sub 5}S{sub 8} shows a sharp magnetic transition at 42 K, accompanied by magnetoelastic behavior. CsCr{sub 5}S{sub 8} shows a structural transition around 100 K, followed by a magnetic transition at 10 K. In Sr{sub 0.5}Cr{sub 5}S{sub 8}, ferromagnetic interaction develops below 100 K and then a three-dimensional antiferromagnetic order takes place at 30 K. These magnetic properties are discussed from A-cation dependences of local structures and a model of magnetic structure for RbCr{sub 5}S{sub 8} is proposed on the basis of the arguments of magnetic interactions and neutron diffraction data. It is different from the known magnetic structure of TlCr{sub 5}Se{sub 8}. - Graphical abstract: Temperature dependences of magnetic susceptibilities for pseudo-hollandite sulfides, ACr{sub 5}S{sub 8} (A=K, Rb, Cs) and A{sub 0.5}'Cr{sub 5}S{sub 8} (A'=Sr, Ba). The observed magnetic frustration effect originates in the triangular lattice.

36 MATERIALS SCIENCE↗

TRENDS IN {sup 44}Ti AND {sup 56}Ni FROM CORE-COLLAPSE SUPERNOVAE

We compare the yields of {sup 44}Ti and {sup 56}Ni produced from post-processing the thermodynamic trajectories from three different core-collapse models-a Cassiopeia A progenitor, a double shock hypernova progenitor, and a rotating two-dimensional explosion-with the yields from exponential and power-law trajectories. The peak temperatures and densities achieved in these core-collapse models span several of the distinct nucleosynthesis regions we identify, resulting in different trends in the {sup 44}Ti and {sup 56}Ni yields for different mass elements. The {sup 44}Ti and {sup 56}Ni mass fraction profiles from the exponential and power-law profiles generally explain the tendencies of the post-processed yields, depending on which regions are traversed by the model. We find that integrated yields of {sup 44}Ti and {sup 56}Ni from the exponential and power-law trajectories are generally within a factor two or less of the post-process yields. We also analyze the influence of specific nuclear reactions on the {sup 44}Ti and {sup 56}Ni abundance evolution. Reactions that affect all yields globally are the 3{alpha}, p(e{sup -}, {nu}{sub e})n and n(e{sup +},{nu}-bar{sub e})p. The rest of the reactions are ranked according to their degree of impact on the synthesis of {sup 44}Ti. The primary ones include {sup 44}Ti({alpha}, p){sup 47}V, {sup 40}Ca({alpha}, {gamma}){sup 44}Ti, {sup 45}V(p, {gamma}){sup 46}Cr, {sup 40}Ca({alpha}, p){sup 43}Sc, {sup 17}F({alpha}, p){sup 20}Ne, {sup 21}Na({alpha}, p){sup 24}Mg, {sup 41}Sc(p, {gamma}){sup 42}Ti, {sup 43}Sc(p, {gamma}){sup 44}Ti, {sup 44}Ti(p, {gamma}){sup 45}V, and {sup 57}Ni(p, {gamma}){sup 58}Cu, along with numerous weak reactions. Our analysis suggests that not all {sup 44}Ti need to be produced in an {alpha}-rich freeze-out in core-collapse events, and that reaction rate equilibria in combination with timescale effects for the expansion profile may account for the paucity of {sup 44}Ti observed in supernova remnants.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Tribocorrosion of stainless steel sliding against graphite in FLiNaK molten salt

The molten salt reactor (MSR) concept recently gained renewed interest in developing Generation IV nuclear reactors. One MSR design uses fluoride molten salts to cool tri-structural isotropic particle fuel encapsulated by a carbon matrix into spherical pebbles, which would inevitably contact the reactor's stainless steel container wall during salt circulation. Characterizing this interaction is crucial for reactor safety. Here, in this work, we report the tribocorrosion behavior of graphite sliding against Type 316H stainless steel lubricated by a FLiNaK (LiF:NaF:KF; 46.5:11.5:42 mol %) molten salt in an argon environment. Accelerated wear loss was observed at a higher temperature because of a lower molten salt viscosity and a higher corrosion rate. The graphite had a more rapid material loss at a higher sliding speed than stainless steel because of its higher vulnerability to vibration-induced microfracture. The salt-starved condition caused more material loss than either the no-salt or the salt-flooded condition because neither a graphite transfer film nor stable boundary lubrication could be established at salt starvation. An interesting dual-layer surface film was discovered on the stainless steel worn surface: a chromium-rich top film and a nickel-accumulated but chromium-depleted interlayer. The film composition and structure provide fundamental insights to the mechanochemical interactions between stainless steel and graphite in a molten salt environment.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Effects of Thiocyanate on Anodic Dissolution of Iron, Chromium, Nickel and Type 304 Stainless Steel. II. Surface Analysis by XPS

As proposed in Part I of this paper, the accelerating effect of thiocyanate on active dissolution of stainless steel in acid sulfate solution occurs by adsorption of sulfur on the steel surface, causing accelerated dissolution of chromium from the steel surface. Surface analysis (X-ray photoelectron spectroscopy) was performed on pure chromium and nickel, a high-purity Fe-20wt% Cr alloy and Type 430 and Type 304 stainless steel to test the proposed mechanism. Surface analysis of the Fe 20wt% Cr alloy and stainless steels (Types 430 and 304) confirmed that chromium enriched on the metal surface during anodic dissolution in thiocyanate-free solution and that the surface enrichment of chromium was smaller in thiocyanate-containing solution. Surface analysis also confirmed the formation of sulfide or adsorbed sulfur on the Fe-20wt% Cr alloy in thiocyanate-containing solution. Surface restructuring of sulfide-covered electrode (Type 304 stainless steel and nickel) was the possible reason why increased anodic current density was observed immediately following interruption of anodic polarization for periods of 5s to 120s.

36 MATERIALS SCIENCE↗

Recent developments on 2D magnetic materials: challenges and opportunities

The emergence of two-dimensional (2D) magnetic materials exhibiting strong magnetization at ultrathin limits above room temperature are promising for miniaturization of devices beyond Moore’s law for future energy efficient nano-electronic devices. Here, the current status, different mechanisms for the existence of magnetism, spin current injection and other magnetic properties of monolayer to few-layers of various 2D magnetic materials are reviewed. Some of the promising applications of these materials are spintronics devices such as spin valves, spin tunnel field-effect transistors, and spin filtering magnetic tunnel junctions. Due to the tunable electronic properties of these 2D materials, it's quite interesting to inject the spin current with suitable ferromagnetic contacts. For instance,black phosphorus is a layered material with a small Schottky barrier height capable of injecting spin current. This review includes many recently explored 2D magnetic materials ranging from exfoliated 2D crystals to CVD grown materials from single to several layers, demonstrating tunable layer dependent magnetic properties. We also explore some of the promising theoretical study based on 2D magnetic compounds such as 2D alkali-based chromium chalcogenides, which shows ferromagnetic as well as semiconducting behavior. The layer-dependent magnetic ordering has been observed in layered compounds like 1T-CrTe 2 , VSe 2 , CrI 3 , and Fe 3 GeTe 2 , which have great potential for the future applications in magnetic based electronic devices. Finally, we emphasize the challenges, opportunities and future directions of the 2D magnetic materials, where new discoveries might have outstanding impact in transformational scientific breakthroughs towards memory, spintronics, optoelectronics and other multifunctional device applications.

36 MATERIALS SCIENCE↗

Experimental and Numerical Evaluation of the Thermal-Fluid Characteristics of the Helium-Cooled Modular Divertor with Multiple Jets Using a Reversed Heat Flux Approach

A single-finger unit of the Helium-Cooled Modular Divertor with Multiple Jets (HEMJ) with a plasma-facing surface (PFS) area of about 2 cm 2 has been studied in a helium (He) loop at He mass flow rates m˙ H ≤ 8 g/s and nearly prototypical conditions. Based on previous studies of the single finger of the HEMJ, our Georgia Institute of Technology group is planning to experimentally study larger divertors. Given that the HEMJ test section was heated with an induction heater and that it is impractical to scale this up to divertors with larger PFS areas, a reversed heat flux approach is being considered to measure heat transfer coefficients (HTCs). In this approach, the direction of the heat flux is reversed with water cooling and high-temperature He heating of the outer shell attached to the PFS. This work presents an initial experimental and numerical evaluation of this approach for a single HEMJ finger. Experiments with brass and copper-chromium-zirconium outer shells were conducted at dimensionless He mass flow rates or Reynolds numbers Re = 1 × 10 4 to 4.7 × 10 4 , an inlet pressure of 10 MPa, temperatures as great as 673 K, and maximum heat flux of 8.4 MW/m 2 . The experiments verify that the He-side HTCs are independent of the direction of the heat flux. Here, the results agree well with previous Nusselt number correlation and pressure loss coefficients for the HEMJ obtained using the normal heating approach.

42 ENGINEERING↗

Observation of site-controlled localized charged excitons in CrI3/WSe2 heterostructures

Abstract Isolated spins are the focus of intense scientific exploration due to their potential role as qubits for quantum information science. Optical access to single spins, demonstrated in III-V semiconducting quantum dots, has fueled research aimed at realizing quantum networks. More recently, quantum emitters in atomically thin materials such as tungsten diselenide have been demonstrated to host optically addressable single spins by means of electrostatic doping the localized excitons. Electrostatic doping is not the only route to charging localized quantum emitters and another path forward is through band structure engineering using van der Waals heterojunctions. Critical to this second approach is to interface tungsten diselenide with other van der Waals materials with relative band-alignments conducive to the phenomenon of charge transfer. In this work we show that the Type-II band-alignment between tungsten diselenide and chromium triiodide can be exploited to excite localized charged excitons in tungsten diselenide. Leveraging spin-dependent charge transfer in the device, we demonstrate spin selectivity in the preparation of the spin-valley state of localized single holes. Combined with the use of strain-inducing nanopillars to coordinate the spatial location of tungsten diselenide quantum emitters, we uncover the possibility of realizing large-scale deterministic arrays of optically addressable spin-valley holes in a solid state platform.

42 ENGINEERING↗