Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Beam Smoothing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

In-situ ellipsometric studies of optical and surface properties of GaAs(100) at elevated temperatures

A rotating-polarizer ellipsometer was attached to an ultrahigh vacuum (UHV) chamber. A GaAs(100) sample was introduced into the UHV chamber and heated at anumber of fixed elevated temperatures, without arsenic overpressure. In-situ spectroscopic ellipsometric (SE) measurements were taken, through a pair of low-strain quartz windows, to monitor the surface changes and measure the pseudodielectric functions at elevated temperatures. Real-time data from GaAs surface covered with native oxide showed clearly the evolution of oxide desorption at approximately 580 C. In addition, surface degradation was found before and after the oxide desorption. An oxide free and smooth GaAs surface was obtained by depositing an arsenic protective coating onto a molecular beam epitaxy grown GaAs surface. The arsenic coating was evaporated immediately prior to SE measurements. A comparison showed that our room temperature data from this GaAs surface, measured in the UHV, are in good agreement with those in the literature obtained by wet-chemical etching. The surface also remained clean and smooth at higher temperatures, so that reliable temperature-dependent dielectric functions were obtained.

Yao, Huade↗
NASA NTRS1990

Gravitational lensing by a smoothly variable three-dimensional mass distribution

A smooth three-dimensional mass distribution is approximated by a model with multiple thin screens, with surface mass density varying smoothly on each screen. It is found that 16 screens are sufficient for a good approximation of the three-dimensional distribution of matter. It is also found that in this multiscreen model the distribution of amplifications of single images is dominated by the convergence due to matter within the beam. The shear caused by matter outside the beam has no significant effect. This finding considerably simplifies the modeling of lensing by a smooth three-dimensional mass distribution by effectively reducing the problem to one dimension, as it is sufficient to know the mass distribution along a straight light ray.

Lee, Man Hoi↗
NASA NTRS1991

Polarization model applied to Uranian radio emission

The total power and the degree of circular polarization as measured by the Planetary Radio Astronomy experiments on the Voyager spacecraft are modeled. For a source near the electron cyclotron frequency, the degree of circular polarization is determined by the angle between the wave vector and the field. It is shown that the observed strong circular polarization of Uranian smooth low-frequency (SLF) can be modeled as emission that is beamed along the direction of the magnetic field in a filled cone. The main observational constraints of SLF emission from Uranus are met by conjugate sources at about 21 deg from the magnetic equator.

Sawyer, C. B.↗
NASA NTRS2019

Meshless Local Petrov-Galerkin (MLPG) Method with Orthogonal Polynomials for Euler-Bernoulli Beam Problems

In this paper, the feasibility of orthogonal polynomials in the meshless local Petrov Galerkin method (MLPG) method is studied. The orthogonal polynomials, Chebyshev and Legendre polynomials, are used in this MLPG method as trial functions. The test functions used were power functions with smooth derivatives at their ends. The performance of these methods is studied by applying these methods to Euler-Bernoulli beam problems. The MLPG-Galerkin and Legendre methods passed all the patch tests for simple beam problems. Next the formulations are tested on complex beam problems such as beams with partial loadings and continuous beam problems. Problems with load discontinuities and additional supports require special attention. Near discontinuities, judicious choice of number of nodes and nodal placements are needed to obtain accurate deflections, slopes, moments and shear forces. As polynomial functions are used, the large number of nodes can create a transformation matrix that is ill-conditioned, resulting in problems with the inversion of the matrix. The conditioning worsens as the number of nodes are increased beyond 20. Quadruple precision was needed for models to obtain accurate solutions. Even with quadruple precision the accuracy of the method suffers as the number of nodes is increased beyond 20. This appears to be a drawback of the MLPG-Chebyshev and MLPG-Legendre methods.

Raju, Ivatury S.↗
NASA NTRS1996

Soot and Radiation Measurements in Microgravity Jet Diffusion Flames

The subject of soot formation and radiation heat transfer in microgravity jet diffusion flames is important not only for the understanding of fundamental transport processes involved but also for providing findings relevant to spacecraft fire safety and soot emissions and radiant heat loads of combustors used in air-breathing propulsion systems. Our objectives are to measure and model soot volume fraction, temperature, and radiative heat fluxes in microgravity jet diffusion flames. For this four-year project, we have successfully completed three tasks, which have resulted in new research methodologies and original results. First is the implementation of a thermophoretic soot sampling technique for measuring particle size and aggregate morphology in drop-tower and other reduced gravity experiments. In those laminar flames studied, we found that microgravity soot aggregates typically consist of more primary particles and primary particles are larger in size than those under normal gravity. Comparisons based on data obtained from limited samples show that the soot aggregate's fractal dimension varies within +/- 20% of its typical value of 1.75, with no clear trends between normal and reduced gravity conditions. Second is the development and implementation of a new imaging absorption technique. By properly expanding and spatially-filtering the laser beam to image the flame absorption on a CCD camera and applying numerical smoothing procedures, this technique is capable of measuring instantaneous full-field soot volume fractions. Results from this technique have shown the significant differences in local soot volume fraction, smoking point, and flame shape between normal and reduced gravity flames. We observed that some laminar flames become open-tipped and smoking under microgravity. The third task we completed is the development of a computer program which integrates and couples flame structure, soot formation, and flame radiation analyses together. We found good agreements between model predictions and experimental data for laminar and turbulent flames under both normal and reduced gravity. We have also tested in the laboratory the techniques of rapid-insertion fine-wire thermocouples and emission pyrometry for temperature measurements. These techniques as well as laser Doppler velocimetry and spectral radiative intensity measurement have been proposed to provide valuable data and improve the modeling analyses.

Ku, Jerry C.↗
NASA NTRS1988

Height-tapered double cantilever beam specimen for study of rate effects on fracture toughness of composites

Loading rate effects on the mode I delamination fracture toughness of AS4/3501-6 graphite/epoxy are presently studied by means of a height-tapered double-cantilever beam specimen whose height contour is designed to furnish a slightly decreasing compliance with increasing crack length, in order to yield a stable and smooth crack propagation at high loading rates. This specimen geometry also allows much higher crack propagation velocities to be obtained with either uniform or width-tapered double cantilever beam specimens.

Yaniv, Gershon↗
NASA NTRS1985

Gaussian beams for surface waves in laterally slowly-varying media

Asymptotic ray theory is applied to surface waves in a medium where the lateral variations of structure are very smooth. The elastodynamic equations of motion in ray-centered coordinates are derived, and a laterally slowly-varying approximation for elastodynamic equations is obtained. Parabolic equations for Love and Rayleigh waves are studied and solved, and the properties of Gaussian beams of seismic surface waves are examined.

Yomogida, K.↗
NASA NTRS1990

A rough-surface thermophysical model for airless planets

A model for determining diurnal temperatures in spherical-section depressions and which encompasses both subsurface heat-flow and direct and scattered sunlight effects is presently applied to the disk-integrated thermal emission of a rough planetary surface with nonzero thermal inertia. Attention is given to the variation with roughness and thermal inertia of the beaming parameter eta, which characterizes zero-phase thermal emission by comparison with a smooth, nonrotating body and is almost independent of albedo for a given surface roughness. The thermal phase curve of Ceres is noted to be well matched by the model features of (1) prograde rotation, (2) 44-deg rms surface slope, and (3) a thermal inertia that is 30 percent of the lunar value.

Spencer, John R.↗
NASA NTRS1989

Lower-hybrid wave generation in an electron beam of finite transverse dimension

The generation of lower-hybrid waves in an inhomogeneous electron beam is examined. Wave amplitudes are invariably limited by the convective nature of the instability. The self-consistent shear of the magnetic-field geometry due to the beam current is limited to the role of dividing the general problem into separate cases according to the relative orientation of the wave vector and direction of inhomogeneity. Moreover, the limiting case of small shear is smoothly connected to the case where shear is altogether negligible. Estimates of the amplification of lower-hybrid waves propagating across the electron beam are made for the various cases.

Crew, G. B.↗
NASA NTRS1959

The Effect of Beam Loading on Water Impact Loads and Motions

An investigation of the effect of beam loading on impact loads and motions has been conducted in the Langley impact basin. Water impact tests of flat-bottom 5-inch-and 8-inch-beam models having beam-loading coefficients C(sub Delta) from 62.5 to 544 and a 30 deg dead-rise 5-inch-beam model A having beam-loading coefficients from 208 to 530 are described and the results analyzed to show trends of these heavy-beam-loading data with initial flight-path angle, trim angle, dead-rise angle, and time through- out the impact. Data from flat-bottom model tests, C(sub Delta) = 4.4 to 36.5, and from 30 deg dead-rise model tests, C(sub Delta) = 0.58 and 18.8, are included, along with the heavy-beam-loading data; and variations of these data with beam-loading coefficients are shown. Each of the load and motion coefficients is found to be directly proportional to a power factor of C(sub Delta). For instance, the maximum impact lift coefficient is found C(sub L,max) to be directly proportional to C(sub Delta, exp 0,33) for the flat-bottom model and C(sub Delta, exp 0,45) for the 30 deg dead-rise model. These variations of C(sub L, max) with C(sub Delta) are found to be in agreement with theoretical variations. Finally, an empirical equation for the prediction of C(sub L,max) is presented and is shown to give good agreement with experimental C(sub L, max) for about 500 fixed-trim smooth-water impacts. The range of variables included dead-rise angles from 0 deg to deg, beam-loading coefficients from o.48 to 544, trim angles from 3 deg to deg, and initial flight-path angles from about 2 deg to about deg.

Mixson, John S.↗
NASA NTRS1959

The Effect of Beam Loading on Water Impact Loads and Motions

An investigation of the effect of beam loading on impact loads and motions has been conducted in the Langley impact basin. Water impact tests of flat-bottom 5-inch- and 8-inch-beam models having beam-loading coefficients C(sub Delta) from 62.5 to 544 and a 30 0 dead-rise 5-inch-beam model A having beam-loading coefficients from 208 to 530 are described and the results analyzed to show trends of these heavy-beam-loading data with initial flight-path angle, trim angle, dead-rise angle, and time throughout the impact. Data from flat-bottom model tests, C(sub Delta) = 4.4 to 36.5, and from 300 dead-rise model tests, C(sub Delta)A = 0.58 and 18.8, are included, along with the heavy-beam-loading data; and variations of these data with beam-loading coefficients are shown. Each of the load and motion coefficients is found to be directly proportional to a power factor ofC(sub Delta). For instance, the maximum impact lift coefficient C(sub L,max)is found to be directly proportional to C(sub Delta)(sup 0.33) for the flat-bottom model and C(sub Delta)(sup 0.45) for the 30 deg dead-rise model. These variations of C(sub L,max) C(sub Delta) are found to be in agreement with theoretical variations. Finally, an empirical equation for the prediction of C(sub L,max) is presented and is shown to give good agreement with experimental C(sub L,max) for about 500 fixed-trim smooth-water impacts. The range of variables included dead-rise angles from 0 deg to 30 deg, beam-loading coefficients from 0.48 to 544, trim angles from 3 deg to 45 deg and initial flight-path angles from about 2 deg to about 27 deg.

Mixson, John S.↗
NASA NTRS1994

On Bi-Grid Local Mode Analysis of Solution Techniques for 3-D Euler and Navier-Stokes Equations

A procedure is presented for utilizing a bi-grid stability analysis as a practical tool for predicting multigrid performance in a range of numerical methods for solving Euler and Navier-Stokes equations. Model problems based on the convection, diffusion and Burger's equation are used to illustrate the superiority of the bi-grid analysis as a predictive tool for multigrid performance in comparison to the smoothing factor derived from conventional von Neumann analysis. For the Euler equations, bi-grid analysis is presented for three upwind difference based factorizations, namely Spatial, Eigenvalue and Combination splits, and two central difference based factorizations, namely LU and ADI methods. In the former, both the Steger-Warming and van Leer flux-vector splitting methods are considered. For the Navier-Stokes equations, only the Beam-Warming (ADI) central difference scheme is considered. In each case, estimates of multigrid convergence rates from the bi-grid analysis are compared to smoothing factors obtained from single-grid stability analysis. Effects of grid aspect ratio and flow skewness are examined. Both predictions are compared with practical multigrid convergence rates for 2-D Euler and Navier-Stokes solutions based on the Beam-Warming central scheme.

Ibraheem, S. O.↗
NASA NTRS1998

Effective Area of the AXAF High Resolution Camera (HRC)

The AXAF High-Resolution Camera (HRC) was calibrated at NASA MSFC's X-Ray Calibration Facility (XRCF) during 1997 March and April. We have undertaken an analysis of the HRC effective area using all data presently available from the XRCF. We discuss our spectral fitting of the beam-normalization detectors (BNDs), our method of removing higher order contamination lines present in the spectra, and corrections for beam non-uniformities. We apply a model of photon absorption depth in order to fit a smooth curve to the quantum efficiency of the detector. This is then combined with the most recent model of the AXAF High-Resolution Mirror Assembly (HRMA) to determine the ensemble effective area versus energy for the HRC. We also address future goals and concerns.

Patnaude, Daniel↗
NASA NTRS1973

Characterization of nickel-copper alloy specimens processed as a part of the M553 sphere forming experiment during the Skylab 1 and 2 flight

Both processed nickel-copper alloy specimens apparently completely melted by the electron beam in the Skylab M512 materials processing facility and either floated free in space, but collided with some smooth flat surface before solidifying, or remained attached to its support post during solidification. Both specimens had a smooth flat area on the surface due to this adherence during solidification. The nominal composition of the alloy before processing in space was 70 percent Ni and 30 percent Cu. Tests show that a considerable amount of copper was lost during processing by evaporation. It was further found that less copper was present in the cap areas, particularly at the surface, than was in the remainder of the specimens. The microchemistry of the dendrites and interdendritic regions, however, is in agreement with the phase diagram for this alloy. The measured densities of these specimens were less than the theoretical density of the alloy due to the amount of porosity present, however, no large voids were found by radiographic techniques.

Hubbard, J. L.↗
NASA NTRS2009

Fabricating Radial Groove Gratings Using Projection Photolithography

Projection photolithography has been used as a fabrication method for radial grove gratings. Use of photolithographic method for diffraction grating fabrication represents the most significant breakthrough in grating technology in the last 60 years, since the introduction of holographic written gratings. Unlike traditional methods utilized for grating fabrication, this method has the advantage of producing complex diffractive groove contours that can be designed at pixel-by-pixel level, with pixel size currently at the level of 45 45 nm. Typical placement accuracy of the grating pixels is 10 nm over 30 nm. It is far superior to holographic, mechanically ruled or direct e-beam written gratings and results in high spatial coherence and low spectral cross-talk. Due to the smooth surface produced by reactive ion etch, such gratings have a low level of randomly scattered light. Also, due to high fidelity and good surface roughness, this method is ideally suited for fabrication of radial groove gratings. The projection mask is created using a laser writer. A single crystal silicon wafer is coated with photoresist, and then the projection mask, with its layer of photoresist, is exposed for patterning in a stepper or scanner. To develop the photoresist, the fabricator either removes the exposed areas (positive resist) of the unexposed areas (negative resist). Next, the patterned and developed photoresist silicon substrate is subjected to reactive ion etching. After this step, the substrate is cleaned. The projection mask is fabricated according to electronic design files that may be generated in GDS file format using any suitable CAD (computer-aided design) or other software program. Radial groove gratings in off-axis grazing angle of incidence mount are of special interest for x-ray spectroscopy, as they allow achieving higher spectral resolution for the same grating area and have lower alignment tolerances than traditional in-plane grating scheme. This is especially critical for NASA Constellation- X project that will utilize hundreds of gratings all of which need to be precisely aligned for x-ray observation of space.

Iazikov, Dmitri↗
NASA NTRS1969

Titanium reinforced boron-polyimide composite

Processing techniques for boron polyimide prepreg were developed whereby composites could be molded under vacuum bag pressure only. A post-cure cycle was developed which resulted in no loss in room temperature mechanical properties of the composite at any time during up to 16 hours at 650 F. A design utilizing laminated titanium foil was developed to achieve a smooth transition of load from the titanium attachment points into the boron-reinforced body of the structure. The box beam test article was subjected to combined bending and torsional loads while exposed to 650 F. Loads were applied incrementally until failure occurred at 83% design limit load.

Clark, G. A.↗
NASA NTRS1987

Luminal surface fabrication for cardiovascular prostheses

Methodology used for the production of highly ordered surfaces on polytetrafluoroethylene (PTFE) Teflon, for use of this material as a surface layer in small-diameter vascular prostheses, is described. Directed argon-ion beam sputter etching is used to produce highly ordered specific surface morphologies, and photolithographic techniques are used for pattern definition. The methodology also includes surface polishing of the samples, sputter deposition of the intermediary layer of gold to enhance photoresist adhesion and improve pattern resolution, and rotating of the sample to minimize the effects of ion-beam nonuniformity and asymmetry. Use of these techniques resulted in the formation of regular arrays of sharply defined hexagonal pillars with smooth vertical walls and large relief.

Deininger, William D.↗
NASA NTRS2008

Advanced Precipitation Radar Antenna to Measure Rainfall From Space

To support NASA s planned 20-year mission to provide sustained global precipitation measurement (EOS-9 Global Precipitation Measurement (GPM)), a deployable antenna has been explored with an inflatable thin-membrane structure. This design uses a 5.3 5.3-m inflatable parabolic reflector with the electronically scanned, dual-frequency phased array feeds to provide improved rainfall measurements at 2.0-km horizontal resolution over a cross-track scan range of up to 37 , necessary for resolving intense, isolated storm cells and for reducing the beam-filling and spatial sampling errors. The two matched radar beams at the two frequencies (Ku and Ka bands) will allow unambiguous retrieval of the parameters in raindrop size distribution. The antenna is inflatable, using rigidizable booms, deployable chain-link supports with prescribed curvatures, a smooth, thin-membrane reflecting surface, and an offset feed technique to achieve the precision surface tolerance (0.2 mm RMS) for meeting the low-sidelobe requirement. The cylindrical parabolic offset-feed reflector augmented with two linear phased array feeds achieves dual-frequency shared-aperture with wide-angle beam scanning and very low sidelobe level of -30 dB. Very long Ku and Ka band microstrip feed arrays incorporating a combination of parallel and series power divider lines with cosine-over-pedestal distribution also augment the sidelobe level and beam scan. This design reduces antenna mass and launch vehicle stowage volume. The Ku and Ka band feed arrays are needed to achieve the required cross-track beam scanning. To demonstrate the inflatable cylindrical reflector with two linear polarizations (V and H), and two beam directions (0deg and 30deg), each frequency band has four individual microstrip array designs. The Ku-band array has a total of 166x2 elements and the Ka-band has 166x4 elements with both bands having element spacing about 0.65 lambda(sub 0). The cylindrical reflector with offset linear array feeds reduces the complexity from "NxN" transmit/receive (T/R) modules of a conventional planar-phased array to just "N" T/R modules. The antenna uses T/R modules with electronic phase-shifters for beam steering. The offset reflector does not provide poor cross-polarization like a double- curved offset reflector would, and it allows the wide scan angle in one plane required by the mission. Also, the cylindrical reflector with two linear array feeds provides dual-frequency performance with a single, shared aperture. The aperture comprises a reflective surface with a focal length of 1.89 m and is made from aluminized Kapton film. The reflective surface is of uniform thickness in the range of a few thousandths of an inch and is attached to the chain-link support structure via an adjustable suspension system. The film aperture rolls up, together with the chain-link structure, for launch and can be deployed in space by the deployment of the chain-link structure.

Rahmat-Samii, Yahya↗