Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BEAMS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Observations of VHF emissions from 50-mA electron beam injections in the ionosphere that are associated with beam-induced discharges

Results are presented of observations of strong VHF plasma waves with amplitudes in excess of 0.1 mV/m (Hz)1/2 associated with 50 mA electron beam injections in the ionosphere. Data from three swept-frequency receivers carried on two daughter payloads are analyzed to determine the emission spectra of the electron beam for various energies and currents. These results were obtained from the rocket-borne experiment SCEX 3, NASA flight 39.002 UE, launched February 1, 1990. The accelerator payload also carried photometers, which measured luminosity at wavelengths of 391.4 and 380.5 nm. Several times during electron gun activity the measured luminosity increased much faster than proportional to the beam current. This nonlinear increase is evidence that a discharge is occurring in the vicinity of the accelerator payload. It is inferred from the uniform distribution of the luminosity around the accelerator payload that the observed discharge extends significantly outside the beam cylinder.

Goerke, R. T.↗
NASA NTRS1991

Gaussian beam and physical optics iteration technique for wideband beam waveguide feed design

The Gaussian beam technique has become increasingly popular for wideband beam waveguide (BWG) design. However, it is observed that the Gaussian solution is less accurate for smaller mirrors (approximately less than 30 lambda in diameter). Therefore, a high-performance wideband BWG design cannot be achieved by using the Gaussian beam technique alone. This article demonstrates a new design approach by iterating Gaussian beam and BWG parameters simultaneously at various frequencies to obtain a wideband BWG. The result is further improved by comparing it with physical optics results and repeating the iteration.

Veruttipong, W.↗
NASA NTRS2003

Correcting for Beam Aberrations in a Beam-Waveguide Antenna

A method for correcting the aim of a beam-waveguide microwave antenna compensates for the beam aberration that occurs during radio tracking of a target that has a component of velocity transverse to the line of sight from the tracking station. The method was devised primarily for use in tracking of distant target spacecraft by large terrestrial beam-waveguide antennas of NASA's Deep Space Network (DSN). The method should also be adaptable to tracking, by other beam-waveguide antennas, of targets that move with large transverse velocities at large distances from the antennas.

Franco, Manuel↗
NASA NTRS1972

Smoke Plume Analysis Using Fan-beam and Single-beam Radiometers

Smoke plume data were taken using the stacks of the Mills Road Steam Plant on Redstone Arsenal, Huntsville, Alabama. The fan-beam unit was placed approximately 235 meters east of the Mills Road Steam Plant, and the single-beam unit was placed approximately 80 meters north of the fan-beam unit. Results of the smoke plume measurements indicate that the smoke plume is a periodic process near the mouth of the smokestack. The usefulness of the system is limited because of inaccurate and cumbersome positioning methods and base line constraints due to cable length. It is recommended that the radiometers be mounted on pedestals which have both azimuth and elevation positions determined by digitally controlled stepper drive motors. It is also recommended that a time multiplex system be used to transmit data from the radiometers to the electronics van.

Dodd, J. L.↗
NASA NTRS1981

Effective path length corrections in beam-beam scattering experiments

The effect of the change of scattering geometry with scattering angle in beam-beam experiments is investigated. Atomic (molecular) target distributions associated with static gas, orifice, tube, capillary array (with and without further collimation), and jet sources have been considered in model calculations for a number of commonly used electron scattering geometries. The relationship between scattering intensity, cross section, and the geometrical integral called 'effective path length' is derived. Volume correction factors (the reciprocal of effective path length) have been calculated for sample cases to illustrate the effect of various beam and scattering geometry characteristics. The validity of the model calculation has been experimentally verified. Most of the commonly used scattering geometries require significant correction of the scattering intensity distributions, but with proper planning scattering geometries can be designed such that the intensity and the cross section angular distribution are identical within 1%.

Brinkmann, R. T.↗
NASA NTRS1989

Far field beam pattern of one MW combined beam of laser diode array amplifiers for space power transmission

The far-field beam pattern and the power-collection efficiency are calculated for a multistage laser-diode-array amplifier consisting of about 200,000 5-W laser diode arrays with random distributions of phase and orientation errors and random diode failures. From the numerical calculation it is found that the far-field beam pattern is little affected by random failures of up to 20 percent of the laser diodes with reference of 80 percent receiving efficiency in the center spot. The random differences in phases among laser diodes due to probable manufacturing errors is allowed to about 0.2 times the wavelength. The maximum allowable orientation error is about 20 percent of the diffraction angle of a single laser diode aperture (about 1 cm). The preliminary results indicate that the amplifier could be used for space beam-power transmission with an efficiency of about 80 percent for a moderate-size (3-m-diameter) receiver placed at a distance of less than 50,000 km.

Kwon, Jin H.↗
NASA NTRS1993

Gaussian-Beam/Physical-Optics Design Of Beam Waveguide

In iterative method of designing wideband beam-waveguide feed for paraboloidal-reflector antenna, Gaussian-beam approximation alternated with more nearly exact physical-optics analysis of diffraction. Includes curved and straight reflectors guiding radiation from feed horn to subreflector. For iterative design calculations, curved mirrors mathematically modeled as thin lenses. Each distance Li is combined length of two straight-line segments intersecting at one of flat mirrors. Method useful for designing beam-waveguide reflectors or mirrors required to have diameters approximately less than 30 wavelengths at one or more intended operating frequencies.

Veruttipong, Watt↗
NASA NTRS1995

A Coupled Layerwise Analysis of the Thermopiezoelectric Response of Smart Composite Beams Beams

Thermal effects are incorporated into previously developed discrete layer mechanics for piezoelectric composite beam structures. The updated mechanics explicitly account for the complete coupled thermoelectromechanical response of smart composite beams. This unified representation leads to an inherent capability to model both the sensory and actuator responses of piezoelectric composite beams in a thermal environment. Finite element equations are developed and numerical results are presented to demonstrate the capability of the current formulation to represent the behavior of both sensory and active smart structures under thermal loadings.

Lee, H.-J.↗
NASA NTRS1972

Oscillation of laser-beam intensity as observed with beam splitters

Characteristics of nearly perfectly flat beam splitter for observing laser pulse shapes are discussed. Disadvantages of conventional instruments for observing properties of laser beams are described. Effects of high frequency noise on accuracy of measurement are reported.

Kuehn, D. M.↗
NASA NTRS1974

Electron beam, laser beam and plasma arc welding studies

This program was undertaken as an initial step in establishing an evaluation framework which would permit a priori selection of advanced welding processes for specific applications. To this end, a direct comparison of laser beam, electron beam and arc welding of Ti-6Al-4V alloy was undertaken. Ti-6Al-4V was selected for use in view of its established welding characteristics and its importance in aerospace applications.

Banas, C. M.↗
NASA NTRS1982

Packet communication system for a multi-beam beam switched satellite repeater

This paper presents the design of a packet-switched communication system using a multi-beam, beam switched satellite repeater. The protocol provides a combination of random access via Slotted ALOHA techniques and demand assigned access using collision requests. This allows efficient bandwidth usage and low average delays. Minimization of earth station cost was a major objective. This was achieved by transferring the bulk of the system complexity to the satellite repeater and the (ground) network controller. This centrally controlled protocol would allow greater system stability and would permit system reconfiguration in response to changes in traffic intensity. Sufficient signalling is also incorporated to allow both rate diversity to combat fading and timing corrections to account for satellite drift.

Bose, S. K.↗
NASA NTRS1986

Beam-plasma instabilities and the beam-plasma discharge

Using a new waves on magnetized beams and turbulence (WOMBAT) 0-450 eV electron gun, measurements bearing on the generation of beam-plasma discharge (BPD) are made. The new gun has a narrower divergence angle than the old, and the BPD ignition current is found to be proportional to the cross-sectional area of the plasma. The high-frequency instabilities are identified with the two Trivelpiece-Gould modes, (1959). The upper frequency is identified as a Cerenkov resonance with the upper Trivelpiece-Gould mode, and the lower frequency with a cyclotron resonance with the lower mode, in agreement with theoretical expectations. Convective growth rates are found to be small. A mechanism involving the conversion of a convective instability to an absolute one by trapping of the unstable waves in the density perturbations of the low-frequency waves, is suggested for the low-frequency wave control of the onset of the high frequency precursors to the BPD.

Kellogg, P. J.↗