Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Arc Flash”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

High Voltage Surge Protection by a Varistor-Filled Air Gap

The electric discharge across a varistor granule filled air gap under a fast-rising voltage pulse was investigated for surge protection applications. The effects of temperature and pressure on the arc and the electrical conduction were analyzed by the characteristic changes in voltage waveforms triggered by a fast-rising high voltage pulse. In addition to the gap size, experimental results show that competing mechanisms among arc conduction, conduction through the varistor granule network, thermionic emission from Joule heating at granule-to-granule contact points, and the magnitude of the switching voltage dictate the maximum surge protection voltage for the filled air gap. Experimental evidence indicated that accumulated degradation was created at small contact points between varistor granules by repetitive assaults from longer duration, high voltage pulses. The uniqueness of using varistor over other dielectric granules in an air gap for surge protection is identified and discussed.

36 MATERIALS SCIENCE↗

Safety Related Concerns with Installation and Use of Switch-Rated Plug/Receptacle Combinations in Lieu of Metal-Enclosed Disconnect Switches

The manufacturers of Nationally Recognized Testing Laboratory (NRTL) listed, switch-rated, plug and receptacle combinations tout their convenience, reliability, efficiency, and compliance with both the National Fire Protection Association (NFPA) 70®, National Electric Code (NEC), and National Fire Protection Association 70E®, The Standard for Electrical Safety in the Workplace, as advantages to using these products in lieu of traditional metal-enclosed disconnect switches. The purpose of this paper is to raise awareness of several unintended consequences that can result when replacement involves high energy cord and plug connected equipment. This paper describes several possible issues in complying with the NFPA 70 Articles 110 and 400 and NFPA 70E Articles 110 and 130 that should be considered when using load rated plug/receptacle combinations. This paper is intended to address high energy circuits typically associated with 480 volt pin and sleeve type connections in applications where incident energy levels may exceed 1.2 calories/centimeter² (cal/cm²).

99 GENERAL AND MISCELLANEOUS↗

New Voltage and Current Thresholds Determined for Sustained Space Plasma Arcing

It has been known for many years, based partly on NASA Glenn Research Center testing, that high-voltage solar arrays arc into the space plasma environment. Solar arrays are composed of solar cells in series with each other (a string), and the strings may be connected in parallel to produce the entire solar array power. Arcs on solar arrays can damage or destroy solar cells, and in the extreme case of sustained arcing, entire solar array strings, in a flash. In the case of sustained arcing (discovered at Glenn and applied to the design and construction of solar arrays on Space Systems/Loral (SS/Loral, Palo Alto, CA) satellites, Deep-Space 1, and Terra), an arc on one solar array string can couple to an adjacent string and continue to be powered by the solar array output until a permanent electrical short is produced. In other words, sustained arcs produced by arcs into the plasma (so-called trigger arcs) may turn into disastrous sustained arcs by involving other array strings.

Dale C. Ferguson↗

Electrostatic discharging behaviour of Kapton irradiated with electrons

The electrostatic charging and discharging of Kapton when irradiated with monoenergetic electrons of 5 to 30 keV energy were studied. The leakage currents and rates of discharging always increased with the incident electron energy and flux, whereas the surface voltage showed a more complex behavior depending on the thickness of the material: for the thinner films it exhibited a maximum and then fell at higher energies. The surface voltage, the rate of discharging, and the peak current and total charge flow during a discharge were enhanced as the temperature was decreased from 70 C to -180 C, and were accompanied by a decreasing leakage current. Visible light or the presence of an aluminum coating on the irradiated surface caused reductions in the surface voltage and changes in the discharging characteristics. The results are discussed in terms of the leakage currents and the secondary emission of electrons. Photomicrographs taken after irradiation, and photographs of samples during irradiation, show good correlations between the positions of light flashes and of pinholes produced by the discharge arcs.

Verdin, D.↗

Mean elements of GEOS 1 and GEOS 2.

A combined analytical-numerical procedure for determining mean orbital elements is presented and applied to the orbits of GEOS 1 and GEOS 2. The precision of the mean semi-major axes of these orbits is a few tens of centimeters when optical flash data are used to determine 2 day orbital arcs. Four day Minitrack orbits give mean semi-major axes of a few meters precision. The mean orientation parameters determined from the optical data are obtained to a precision of about 0.1 sec.

Douglas, B. C.↗

Mean elements of GEOS-1 and GEOS-2

A combined analytical-numerical procedure for determining precise mean orbital elements is presented and applied to the orbits of GEOS-1 and GEOS-2. The precision of the mean semi-major axes of these orbits is a few tens of centimeters when optical flash data is used to determine two-day orbital arcs. Four-day Minitrack orbits give mean semi-major axes of a few meters precision. The mean orientation parameters are obtained to a precision of about 0.1 sec (about 3m) or better from the optical orbits. This precision is adequate for determinations of tidal parameters, particularly in the case of GEOS-2, where the tidal perturbation of the inclination is 10 sec.

Douglas, B. C.↗

Pressure and temperature dependence kinetics study of the NO + BrO yielding NO2 + Br reaction - Implications for stratospheric bromine photochemistry

The reactivity of NO with BrO radicals over a wide range of pressure (100-700 torr) and temperature (224-398 K) is investigated using the flash photolysis-ultraviolet absorption technique. The flash photolysis system consists of a high-pressure xenon arc light source, a reaction cell/gas filter/flash lamp combination, and a 216.5 half-meter monochromator/polychromator/spectrography for wavelength selectivity. The details of the reaction and its corresponding Arrhenius expression are identified. The results are compared with previous measurements, and atmospheric implications of the reaction are discussed. The NO + BrO yielding NO2 + Br reaction is shown to be important in controlling the concentration ratios of BrO/Br and BrO/HBr in the stratosphere, but this reaction does not affect the catalytic efficiency of BrOx in ozone destruction.

Watson, R. T.↗

Crystallization of electrically conductive visibly transparent ITO thin films by wavelength-range-specific pulsed Xe arc lamp annealing

Here, the transparent electric conductors made of indium tin oxide (ITO)-doped glass prepared by a flash lamp annealing (FLA) process were compared with ITO-doped glass prepared via a conventional rapid thermal annealing (RTA) process. Stylus surface profilometry was used to determine thicknesses, scanning electron microscopy was used to image surfaces, X-ray diffraction was used to determine film structures, X-ray photoelectron spectroscopy was used to determine oxidation states and film compositions, 4-point probe measurements were used to determine electrical conductivities, UV–Vis spectroscopy was used to determine film transparencies, and selective light filtering was used to determine which wavelengths of light are needed to anneal ITO into a visibly transparent electrically conductive thin film via an FLA process. The results showed that FLA with visible light can be used to nearly instantaneously anneal ITO to create visibly transparent and electrically conductive ITO thin films on glass. The FLA process achieved this by predominately exciting unoxidized indium, unoxidized tin, tin monoxide (SnO), and non-stoichiometric indium oxide (InO x ), appropriately distributed in an electron beam physical vapor-deposited amorphous ITO thin film, to allow their oxidation and crystallization into an electrically conductive visibly transparent ITO. Though it is possible to prepare ITO-doped glass that is more transparent with an RTA process, the FLA process is significantly faster, has comparable electrical conductivity, and can strongly localize heating to areas of the as-deposited ITO thin film that are not electrically conductive and visibly transparent.

36 MATERIALS SCIENCE↗

Welding in space and the construction of space vehicles by welding; Proceedings of the Conference, New Carrollton, MD, Sept. 24-26, 1991

The present conference discusses such topics in spacecraft welding as the NASA Long Duration Exposure Facility's evidence on material properties degradation, EVA/telerobotic construction techniques, welding of the superfluid helium on-orbit transfer flight demonstration tanks and hardware, electron-beam welding of aerospace vehicles, variable-polarity plasma arc keyhole welding of Al, aircraft experiments of low-gravity fusion welding, flash-butt welding of Al alloys, and a computer-aided handbook for space welding fabrication. Also discussed are the welded nozzle extension for Ariane launch vehicles, the existence of on-orbit cold-welding, structural materials performance in long-term space service, high-strength lightweight alloys, steels, and heat-resistant alloys for aerospace welded structures, the NASA-Goddard satellite repair program, and the uses of explosion welding and cutting in aerospace engineering.

Source record↗

Direct effects protection

Protection of an aircraft and each of its various systems against the direct effects of lightning were analyzed. Components located in different sections of the aircraft were individually examined since they are likely to experience different degrees of susceptibility to lightning, and may be vulnerable to different components of the lightning flash. The basic steps to be followed in establishing lightning protection were presented by discussing the varieties of arc entry and current flow-through damage. The lightning-strike zones and lightning current environments are established, since environmental conditions in the zones are those under which specific protective measures must perform. Airworthiness regulations which apply to lightning protection are cited.

Franklin A Fisher↗

Non-Destructive In-Process Assessment of Thermal Spray Repairs

This exploratory project, entitled “Non-Destructive In-process Assessment of Thermal Spray Repairs,” evaluated the capabilities and limitations of four non-destructive testing (NDE) technologies for detection of defects in as-sprayed thermal spray coatings: acousto-ultrasonics, vibro-thermography, thermal wave infrared (IR) imaging, and flash IR thermography. The project goal was to identify a single technology suitable for use as an in-process inspection for two common classes of defects in thermal spray coatings, porosity and disbonds. Two rounds of test coupons were fabricated with intentionally seeded defects in AISI 420 stainless steel coatings deposited by twin wire arc (TWA) spray onto gray cast iron substrates. These standardized test coupons allowed the sensitivity of the four NDE methods to be directly compared. The results indicated that the acousto-ultrasonic method will not meet requirements for accuracy, inspection time, and reproducibility, while the vibrothermography method will not meet requirements for integration within remanufacturing cells and process flows. The IR methods, thermal wave imaging and flash thermography, both exhibited acceptable accuracy and reproducibility; however, the former method does not meet the requirement for inspection time. Flash IR thermography met all requirements in the initial round of testing, and that result was confirmed in a second round of testing on samples with a larger, more complex geometry. A final recommendation for further development of flash IR thermography was therefore made based upon i) detection performance, and ii) feasibility of deployment into the target application of resurfacing CAT engine blocks and headers.

36 MATERIALS SCIENCE↗

Tracking-station coordinates from Geos 1 and Geos 2 optical flash data.

Center-of-mass coordinates for 28 NASA MOTS and SAO Baker-Nunn camera sites have been obtained from optical flash data from Geos 1 (1965 89A) and Geos 2 (1968 002A). More than 25,000 observations in about 100 two-day arcs were used in dynamical solutions (SAO 1969 AGU gravity model). Comparison of results with local survey solutions and with solutions from deep-space vehicle tracking suggests accuracy of about 2 meters in longitude and height and 5 meters in latitude. The relatively larger error in latitude arose from propagation of gravity-model error largely along the track of these high-inclination satellites. The results have also been compared with the solutions of the SAO 1969 standard earth for station coordinates on the North American datum. The solution obtained in the present work is much closer to the survey results in chord length between stations.

Marsh, J. G.↗

Interiors of the giant planets

This theoretical/observational project constrains interior structure of Jovian planets through observational data. Researchers continue to concentrate on Neptune in support of the 1989 Voyager encounter. Occultations of stars by Neptune are observed from the Tucson area and from Chile to obtain information about Neptune's atmosphere and to continue to search for Neptune arcs. Occultations by other solar system objects are also observed as part of collaborative efforts from time to time. New results on the structure of scintillations in the central flash occultation by Neptune on 20 August 1985 were derived. Analysis shows that scintillations are present throughout the lightcurve, both near the half-intensity points (at a pressure of 1 microbar) and near the central flash (at 0.4 mbar). Near the planetary limb, the scintillations are extended parallel to the limb; near the shadow center, they are extended parallel to the limb; near the shadow center, they are extended in a radial direction. Researchers collaborated with Ramesh Narayan to derive a theory relating the scintillations to density fluctuations in Neptune's atmosphere. The theory will ultimately enable researchers to test whether the scintillations are caused by internal gravity waves in Neptune's upper atmosphere.

Hubbard, W. B.↗

Final results of the NASA storm hazards program

Lightning swept-flash attachment patterns and the associated flight conditions were recorded from 1980-1986 during 1496 thunderstorm penetrations and 714 direct strikes with a NASA F-1068 research airplane. These data were studied with an emphasis on lightning avoidance by aircraft and on aircraft protection design. The individual lightning attachment spots, along with crew comments and on-board photographic data were used to identify lightning swept-flash attachment patterns and the orientations of the lightning channels with respect to the airplane. The full-scale in-flight data were compared to results from scale-model arc-attachment tests. The airborne and scale-model data showed that any exterior surface of this airplane may be susceptible to direct lightning attachment. In addition, the altitudes, ambient temperatures, and the relative turbulence and precipitation levels at which the strikes occurred in thunderstorms are summarized and discussed. It was found that the peak strike rate occurred at pressure altitudes betwen 38,000 ft and 40,000 ft, corresponding to ambient temperatures colder than -40 C.

Fisher, Bruce D.↗

Interiors of the giant planets

The Neptune central flash data obtained from the August 20, 1985 occultation was analyzed. The three main objectives of the analysis, which combined the study of the CTIO data with the ESO data obtained by the Meudon groups were: deduce the oblateness, equatorial radius, and pole positon angle of Neptune from a combined analysis of the limb-occultation and central-flash data; determine the temperature/absorption profile in Neptune's atmosphere in the region probed by the occultation data (from 1 microbar to about 0.2 mbar), as well as atmospheric distortions produced by waves or turbulence; and search for additional Neptune ring arcs. Results were discussed in terms of the three main objectives.

Hubbard, W. B.↗

Enhancing thermal conductivity of UO 2 with the addition of UB 2 via conventional sintering techniques

We report that uranium dioxide has been the primary fuel type used in light water reactors for more than 40 years and proven to be reliable and robust. However, the Fukushima-Daiichi nuclear accident has motivated new work evaluating fuels with characteristics promoting accident tolerance, including enhanced thermal conductivity. Recently, additives have been investigated to increase thermal conductivity, but research has been largely focused on non-fissile additions. This study investigated the use of fissile additives to not only increase the thermal conductivity but also increase the uranium loading. Uranium diboride was chosen as the additive for this study due to its promising corrosion behavior as well as its significantly higher thermal conductivity at 573 K (25 Wm -1 K -1 ) when compared to UO 2 (7 Wm -1 K -1 ). Uranium diboride powder was fabricated via the arc melting technique and a ball milling process prior to mixing with UO 2 in a 90/10 wt% UO 2 /UB 2 ratio. Green bodies were made using a uniaxial die and subjected to a traditional pressureless sintering technique at 2073 K in argon. Sintered samples were analyzed via laser flash analysis for thermal diffusivity and differential scanning calorimetry for specific heat capacity in order to calculate thermal conductivity. The samples displayed an increase of 36-55% in thermal conductivity between 323 K and 1273 K when compared to the benchmark samples (pure UO 2 ) as reported in open literature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Flash-photoionized nebulae

Under conditions of high radiation intensity and low gas density, recombination may be neglected in determining the ionization state of a photoionized gas. Calculations of the ionization structure of nebulae in this 'flash-photoionized' regime are reported. Very hard spectra of ionizing ultraviolet radiation may be produced by filtration of the ionizing flux through a neutral hydrogen layer which preferentially absorbs photons just above the hydrogen photoionization threshold. Fluxes with these hard spectra produce gas layer in which helium is largely doubly ionized while hydrogen is largely neutral. Such a layer leads to anomalously high ratios of He II to H I recombination line strengths. These results are applied to the problem of the spectrum of the arc in the cluster of galaxies A370. It is found that the spectrum may possibly be reconciled with the light echo model.

Katz, J. I.↗