Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Al2O3”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Pressure sintering of Si3N4-Al2O3 /Sialon/

Essentially pore-free Sialon bodies were obtained by pressure sintering for three blends (mol ratios of 4:1, 2:3, and 3:2) of Si3N4 and Al2O3 powders under the conditions of 27.6 MN/sq m and a temperature of 1700 C for 2 h. These dense bodies consist mainly of a Sialon solid solution with a minor amount of a particular second phase. The higher the Al2O3 content (20 to 60 mol% range) in Sialon, the higher the densification rate. Fully dense bodies can be obtained at temperatures as low as 1500 C at 27.6 MN/sq m for 2 h with no second phase detectable by X-ray diffraction. A 100% dense body can be obtained by heating at 1700 C at 27.6 MN/sq m without a holding time.

Yeh, H. C.↗
NASA NTRS1979

Some TEM observations of Al2O3 scales formed on NiCrAl alloys

The microstructural development of Al2O3 scales on NiCrAl alloys has been examined by transmission electron microscopy. Voids were observed within grains in scales formed on a pure NiCrAl alloy. Both voids and oxide grains grew measurably with oxidation time at 1100 C. The size and amount of porosity decreased towards the oxide-metal growth interface. The voids resulted from an excess number of oxygen vacancies near the oxidemetal interface. Short-circuit diffusion paths were discussed in reference to current growth stress models for oxide scales. Transient oxidation of pure, Y-doped, and Zr-doped NiCrAl was also examined. Oriented alpha-(Al, Cr)2O3 and Ni(Al, Cr)2O4 scales often coexisted in layered structures on all three alloys. Close-packed oxygen planes and directions in the corundum and spinel layers were parallel. The close relationship between oxide layers provided a gradual transition from initial transient scales to steady state Al2O3 growth.

Smialek, J.↗
NASA NTRS1979

Some TEM observations of Al2O3 scales formed on NiCrAl alloys

The microstructural development of Al2O3 scales on NiCrAl alloys has been examined by transmission electron microscopy. Voids have been observed within grains in scales formed on a pure NiCrAl alloy. Both voids and oxide grains grew measurably with oxidation time at 1100 C. The size and amount of porosity decreased towards the oxide-metal growth interface. It was postulated that the voids resulted from an excess number of oxygen vacancies near the oxide-metal interface. Short-circuit diffusion paths were discussed in reference to current growth stress models for oxide scales. Transient oxidations of pure, Y-doped, and Zr-doped NiCrAl was also examined. Oriented alpha-(Al,Cr)2O3 and Ni(Al,Cr)2O4 scales often coexisted in layered structures on all three alloys. Close-packed oxygen planes and directions in the corundum and spinel layers were parallel. The close relationships between oxide layers provided a gradual transition from initial transient scales to steady state Al2O3 growth.

Smialek, J.↗
NASA NTRS1982

O-18 tracer studies of Al2O3 scale formation on NiCrAl alloys

Diffusion processes in Al2O3 scales formed on NiCrAl + Zr alloys were studied by the proton activation technique employing the O-18 isotope as a tracer. The O-18 profiles identified a zone of oxide penetration beneath the external scale. Both this subscale formation and the outer Al2O3 scale thickness were shown by this technique to increase with Zr content in the alloy. Estimated kp's from scale thicknesses were in agreement with gravimetric measurements for various Zr levels. Alternate exposures in O-16 and O-18 revealed that oxygen inward transport was the primary growth mechanism. A qualitative analysis of these O-18 profiles indicated that the oxygen transport was primarily via short-circuit paths, such as grain boundaries.

Reddy, K. P. R.↗
NASA NTRS1982

Sputtering of Al2O3 and LiNbO3 in the electronic stopping region

Because of recent interest in the role played by the thermal properties of materials that exhibit high energy sputtering, Al2O3 and LiNbO3 were sputtered with chlorine ions at energies between 3 MeV and 25 MeV. To detect the sputtered Al and Nb we employ thin carbon catcher foils, which are analyzed with Rutherford scattering in the forward direction. Al surface densities of 10 to the 14th/sq cm and Nb surface densities of 10 to the 13th/sq cm are easily measured. The sputtering yields for both Al2O3 and LiNbO3 increase rapidly with increasing chlorine energy, and the Al and Nb yields are both approximately 0.2 at 20 MeV. Tests for dose, beam current, and contamination effects will be discussed.

Qiu, Y.↗
NASA NTRS1982

Effect of Y2O3 and Al2O3 on the oxidation resistance of Si3N4

Oxidation of cold-pressed and sintered Si3N4 containing 15 wt% Y2O3 and 2, 4, 6, and 8% Al2O3 is observed at temperatures as low as 1000 C with IR reflection spectroscopy. Concentrations of Al2O3 in excess of 4% greatly retard the rate of oxidation and alter the mechanism of surface attack by promoting formation of a glassy layer on the surface containing mixed oxynitride bonds. The glassy layer retards heterogeneous attack and reduces the effect of an oxidation transition temperature between 1000 and 1100 C for these materials.

Hench, L. L.↗
NASA NTRS1983

Diffusion processes in Al2O3 scales - Void growth, grain growth, and scale growth

The internal microstructure and growth kinetics of Al2O3 scales on Ni-15Cr-13Al (wt percent) are investigated by TEM and analyzed in relation to models of diffusivity. Polished arc-melted specimens were oxidized in 1-atm air at 1100 C for 0.1, 1.0, and 20 hours and ion-thinned for TEM at 100 kV. The frequency distribution of void size and grain size is determined for different oxidation times and scale depths. The kinetics of microvoid growth and of grain and scale growth are plotted and related via simplified models to lattice and grain-boundary oxygen diffusivity, respectively. Good agreement is found between model predictions and data obtained by Oishi and Kingery (1960) on oxygen diffusion in bulk Al2O3. The further implications and limitations of these findings are discssed.

Smialek, J. L.↗
NASA NTRS1983

Analysis of grain boundary phase devitrification of Y2O3- and Al2O3-doped Si3N4

The present study has the objective to show that a Fourier Transform IR (FTIR) spectrometer in a single-beam reflection mode can be used for direct comparison of fractured vs nonfractured Si3N4 surfaces. This can be done because the FTIR method permits a digital summation of nearly 1000 scans of the fracture surface. Commercial-grade Si3N4, Y2O3, and Al2O3 were used in the study. The samples were heat treated in a vacuum induction heating furnace at either 1000 C for 10 h or 1200 C for 10 h each. Use of Fourier transform IR reflection spectroscopic analysis and X-ray diffraction shows that 10 h at 1200 C is sufficient to devitrify the amorphous grain boundary phase of Si3N4 containing 15 percent Y2O3 + 2 percent Al2O3 densification aids.

Hench, L. L.↗
NASA NTRS1986

Adherent Al2O3 scales produced on undoped NiCrAl alloys

Repeated oxidation and polishing of high purity Ni-15Cr-13Al has dramatically changed its cyclic oxidation behavior from nonadherent to adherent. No apparent change in scale phase, morphology or interface structure occurred during this transition, dismissing any mechanism based on pegging, vacancy sink, or growth stress. The principle change that did occur was a reduction in the sulfur content from 10 ppmw to 3 ppmw after 25 cycles at 1120 C. These observations are used to support the model of Al2O3 scale adherence put forth by Smeggil et al. which claims that Al2O3 scale spallation occurs due to sulfur segregation and bond deterioration at the oxide-metal interface.

Smialek, James L.↗
NASA NTRS1988

The effect of Al2O3, CaO, Cr2O3 and MgO on devitrification of silica

The effect of doping on devitrification of vitreous silica was studied at 1100, 1200, and 1300 C. Dispersion of dopants on a molecular scale was accomplished via a sol-gel technique. All dopants accelerated the devitrification of silica but to different degrees. The most active was CaO followed by MgO, Al2O3, and Cr2O3. Pure silica and silica containing Cr2O3 and Al2O3 devitrified to alpha-cristobalite only, whereas silica doped with CaO and MgO produced alpha-quartz and alpha-cristobalite. It appears that prolonged heat treatment would cause alpha-quartz to transform to alpha-cristobalite.

Zaplatynsky, Isidor↗
NASA NTRS1988

Residual infrared absorption in Ti:Al2O3 crystals

The performance of Ti:Al2O3 lasers is impaired generally by an infrared absorption that occurs in the laser output wavelength region. On the basis of data for as-grown and annealed samples cut from Ti:Al2O3 crystals grown by the vertical-gradient-freeze (VGF) technique, we previously proposed that the residual absorption is due to Ti(3+) to Ti(4+) pairs. In this report, we present additional data that confirm this ion-pair model for the residual absorption, which can be attributed to excitation of the 3d electron of the Ti(3+) ion perturbed by the Coulomb field of the neighboring Ti(4+) ion and/or an associated Al vacancy.

Source record↗
NASA NTRS1989

Effect of the theta-alpha-Al2O3 transformation on the oxidation behavior of beta-NiAl+Zr

Isothermal oxidation of NiAl+Zr has been performed over the temperature range of 800-1200 C and studied by TGA, XRD, and SEM. A discontinuous decrease in growth rate of two orders of magnitude was observed at 1000 C due to the formation of alpha-Al2O3 from theta-Al2O3. This transformation also resulted in a dramatic change in the surface morphology of the scales, as a whisker topography was changed into a weblike network of oxide ridges and radial transformation cracks. It is believed that the ridges are evidence for a short-circuit outward aluminum diffusion growth mechanism that has been documented in a number of O-18 tracer studies.

Rybicki, George C.↗
NASA NTRS1991

Tribological properties of Ag/Ti films on Al2O3 ceramic substrates

Ag solid lubricant films, with a thin Ti interlayer for enhanced adhesion, were sputter deposited on Al2O3 substrate disks to reduce friction and wear. The dual Ag/Ti films were tested at room temperature in a pin-on-disk tribometer sliding against bare, uncoated Al2O3 pins under a 4.9 N load at a sliding velocity of 1 m/s. The Ag/Ti films reduced the friction coefficient by 50 percent to about 0.41 compared to unlubricated baseline specimens. Pin wear was reduced by a factor of 140 and disk wear was reduced by a factor of 2.5 compared to the baseline. These films retain their good tribological properties including adhesion after heat treatments at 850 C and thus may be able to lubricate over a wide temperature range. This lubrication technique is applicable to space lubrication, advanced heat engines, and advanced transportation systems.

Dellacorte, Christopher↗
NASA NTRS1991

Sliding wear of self-mated Al2O3-SiC whisker reinforced composites at 23-1200 C

Microstructural changes occurring during sliding wear of self-mated Al2O3-SiC whisker reinforced composites were studied using optical, scanning electron microscopy, and transmission electron microscopy. Pin-on-disk specimens were slid in air at 2.7 m/sec sliding velocity under a 26.5 N load for 1 hr. Wear tests were conducted at 23, 600, 800, and 1200 C. Mild wear with a wear factor of 2.4 times 10(exp -7) to 1.5 times 10(exp -6) cu mm/Nm was experienced at all test temperatures. The composite shows evidence of wear by fatigue mechanisms at 800 C and below. Tribochemical reaction (SiC oxidation and reaction of SiO2 and Al2O3) leads to intergranular failure at 1200 C. Distinct microstructural differences existing at each test temperature are reported.

Farmer, Serene C.↗
NASA NTRS1991

Effect of sulfur removal on Al2O3 scale adhesion

The effect of removing sulfur impurity on the adhesion of Al2O3 scale to NiCrAl was investigated in four experiments. It was found that removing sulfur to concentration less than 1 ppm per weight is sufficient to produce a very significant degree of alpha-Al2O3 scale adhesion to undoped NiCrAl alloys. Results of experiments show that repeated oxidation, and polishing after each oxidation cycle, of pure NiCrAl alloy lowered sulfur content from 10 to 2 ppm by weight (presumably by removing the segregated interfacial layer after each cycle); thinner samples became adherent after fewer oxidation-polishing cycles because of more limited supply of sulfur. It was found that spalling in subsequent cyclic oxidation tests was a direct function of the initial sulfur content. The transition between the adherent and nonadherent behavior was modeled in terms of sulfur flux, sulfur content, and sulfur segregation.

Smialek, James L.↗
NASA NTRS1991

Low-threshold, CW, all-solid-state Ti:Al2O3 laser

A CW Ti:Al2O3 ring laser with a threshold power of 119 mW is demonstrated. It provides a tunable source of single-frequency, diffraction-limited radiation that is suitable for injection seeding. The Ti:Al2O3 laser is operated with a diode-laser-pumped, frequency-doubled, Nd:YAG laser as the sole pump source.

Harrison, James↗
NASA NTRS1991

Protective Al2O3 scale formation on NbAl3-base alloys

The oxidation of NbAl3 with additions of Cr and Y was studied to determine the mechanisms of the beneficial effects of these elements upon oxidation. Cr additions to the binary NbAl3 alloy of up to 6.8 at. percent reduced the scale growth rates and promoted alpha-Al2O3 formation over much longer times relative to binary NbAl3. A major effect of Cr is to form a layer of AlNbCr at the metal/scale interface, which is inherently more oxidation-resistant than the matrix alloy in the long term. Yttrium additions to a Cr-containing alloy improved the scale growth rate and adherence and changed the scale microstructure to mimic that of a typical protective Al2O3 scale.

Doychak, J.↗
NASA NTRS1989

Amplified spontaneous emission measurement of a line-narrowed, tunable, Ti:Al2O3 amplifier using rubidium absorption

Amplified spontaneous emission, ASE, generated by a Ti:Al2O3 laser amplifier has been measured as a function of pump energy, and thus gain, using the atomic absorption of rubidium, Rb, gas at 0.780 micron. By tuning the Ti:Al2O3 laser, the Rb cell could selectively absorb the narrow spectral bandwidth laser radiation while transmitting the wide spectral bandwidth ASE. Transmission of laser amplifier pulses through a Rb absorption cell, measured at various temperatures, thus allows the measurement of the weak ASE in the vicinity of the strong laser pulse. A model for the transmission of Rb as a function of temperature and wavelength has been developed. The measured transmissions are in good agreement with the transmission model predictions.

Barnes, James C.↗