Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AIR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Urban Air Quality Management at Low-Cost Using Micro Air Sensors: A Case Study From Accra, Ghana

Urban air quality management is dependent on the availability of local air pollution data. In many major urban centers of Africa, there is limited to non-existent information on air quality. This is gradually changing in part due to the increasing use of micro air sensors which have the potential to enable the generation of ground-based air quality data at fine scales for understanding local emission trends. Regional literature on the application of the high-resolution data for emission source identification in this region is limited. In this study a micro air sensor was co-located at the Physics Department, University of Ghana with a reference grade instrument to evaluate its performance for estimating PM2.5 pollution accurately at fine scales and the value of this data in identification of local sources and their behavior over time. For this study 15 weeks of data at hourly resolution with approximately 2500 data pairs are generated and analyzed (June 01, 2023, to September 15, 2023). For this time period a coefficient of determination (r 2 ) of 0.83 was generated with a mean absolute error (MAE) of 5.44 μgm -3 between the pre local calibration micro air sensor (i.e. out of box) and the reference-grade instrument. Following currently accepted best practice methods (see e.g., PAS4023) a domain specific (i.e. local) calibration factor was generated using a multi-linear regression model and when this factor is applied to the micro air sensor data, a reduction i.e., improvement in MAE to 1.43 μgm -3 was found. Daily variation was calculated, a receptor model was applied, and time series plots as a function of wind direction were generated, including PM2.5/PM10 ratio scatter and count plots to explore the utility of this observational approach for local source identification. The 3 data sets were compared (out of box, domain calibrated and reference-grade) and it was found that although there were variations in the data reported, source areas highlighted based on these data were similar, with input from local sources such as traffic emissions and biomass burning. As the temporal resolution of observational data associated with these micro air sensors is higher than for reference grade instruments (primarily due to costs and logistics limitations), they have the potential to provide insight into the complex, often hyper localized sources associated with urban areas, such as those found in major African cities.

Source apportionment↗
DOE OSTI2014

Technology Solutions Case Study: Air Leakage and Air Transfer Between Garage and Living Space, Waldorf, Maryland

In this project, Building Science Corporation worked with production homebuilder K. Hovnanian to evaluate air transfer between the garage and living space in a single-family detached home constructed by a production homebuilder in compliance with the 2009 International Residential Code and the 2009 International Energy Conservation Code. The project gathered important information about the performance of whole-building ventilation systems and garage ventilation systems as they relate to minimizing flow of contaminated air from garage to living space. A series of 25 multipoint fan pressurization tests and additional zone pressure diagnostic testing measured the garage and house air leakage, the garage-to-house air leakage, and garage and house pressure relationships to each other and to outdoors using automated fan pressurization and pressure monitoring techniques. While the relative characteristics of this house may not represent the entire population of new construction configurations and air tightness levels (house and garage) throughout the country, the technical approach was conservative and should reasonably extend the usefulness of the results to a large spectrum of house configurations from this set of parametric tests in this one house. Based on the results of this testing, the two-step garage-to-house air leakage test protocol described above is recommended where whole-house exhaust ventilation is employed. For houses employing whole-house supply ventilation (positive pressure) or balanced ventilation (same pressure effect as the baseline condition), adherence to the EPA Indoor airPLUS house-to-garage air sealing requirements should be sufficient to expect little to no garage-to-house air transfer.

air leakage↗
DOE OSTI2019

Numerical Analysis of Detonability Assessment in a Natural Gas-Air Fueled Rotating Detonation Engine

Rotating Detonation Engines (RDE) offer an alternative combustion strategy to replace conventional constant pressure combustion with a process that could produce a pressure gain without the use of a mechanical compressor. Recent numerical and experimental publications that consider air as the oxidizer have primarily focused on the ability of these annular combustors to sustain a stable continuous detonation wave when fueled by hydrogen. However, for this to be a viable consideration for the land-based power generation it is necessary to explore the ability to detonate natural gas and air within the confines of the annular geometry of an RDE. Previous studies on confined detonations have expressed the importance of permitting detonation cells to fully form within the combustor in order to achieve stability. This poses a challenge for natural gas–air fueled processes as their detonation cell size can be quite large even at moderate pressures. Despite the practical importance, only a few studies are available on natural gas detonations for air-breathing RDE applications. Moreover, the extreme thermodynamic condition (high temperature inside the combustor) allows limited accessibility inside the combustor for detailed experimental instrumentations, providing mostly single-point data. Recent experimental studies at the National Energy Technology Laboratory (NETL) have reported detonation failure at higher methane concentration in an air-breathing RDE fueled by natural gas-hydrogen fuel blends. This encourages to perform a detailed numerical investigation on the wave characteristics of detonation in a natural gas-air fueled RDE to understand the various aspects of instability associated with the natural gas-air detonation.This study is a numerical consideration of a methane-air fueled RDE with varying operating conditions to ascertain the ability to achieve a stable, continuous detonation wave. The simulations have been performed in a 2D unwrapped RDE geometry using the open-source CFD library “OpenFOAM” employing an unsteady pressure-based compressible reactive flow solver with a <em>k</em>–<em>ε</em> turbulence model in a structured rectangular grid system. Both reduced and detailed chemical kinetic models have been used to assess the effect of the chemistry on the detonation wave characteristics and the underlying flow features. A systematic grid sensitivity study has been conducted with various grid sizes to quantify the weakly stable overdriven detonation on a coarse mesh and oscillating features at fine mesh resolutions.The main focus of the current study is to investigate the effects of operating injection pressure on detonation wave characteristics of an air-breathing Rotating Detonation Engine (RDE) fueled with natural gas-hydrogen fuel blends. Wave speeds, peak pressures and temperatures, and dominant frequencies have been computed from the time histories. The flow structures were then visualized using 2D contours of temperature and species concentration.

Saha, Pankaj↗
NASA NTRS1974

Air conditioning system and component therefore distributing air flow from opposite directions

The air conditioning system comprises a plurality of separate air conditioning units coupled to a common supply duct such that air may be introduced into the supply duct in two opposite flow directions. A plurality of outlets such as registers or auxiliary or branch ducts communicate with the supply duct and valve means are disposed in the supply duct at at least some of the outlets for automatically channelling a controllable amount of air from the supply duct to the associated outlet regardless of the direction of air flow within the supply duct. The valve means comprises an automatic air volume control apparatus for distribution within the air supply duct into which air may be introduced from two opposite directions. The apparatus incorporates a freely swinging movable vane in the supply duct to automatically channel into the associated outlet only the deflected air flow which has the higher relative pressure.

Obler, H. D.↗
NASA NTRS2010

Improved Determination of Surface and Atmospheric Temperatures Using Only Shortwave AIRS Channels: The AIRS Version 6 Retrieval Algorithm

AIRS was launched on EOS Aqua on May 4, 2002 together with ASMU-A and HSB to form a next generation polar orbiting infrared and microwave atmosphere sounding system (Pagano et al 2003). The theoretical approach used to analyze AIRS/AMSU/HSB data in the presence of clouds in the AIRS Science Team Version 3 at-launch algorithm, and that used in the Version 4 post-launch algorithm, have been published previously. Significant theoretical and practical improvements have been made in the analysis of AIRS/AMSU data since the Version 4 algorithm. Most of these have already been incorporated in the AIRS Science Team Version 5 algorithm (Susskind et al 2010), now being used operationally at the Goddard DISC. The AIRS Version 5 retrieval algorithm contains three significant improvements over Version 4. Improved physics in Version 5 allowed for use of AIRS clear column radiances (R(sub i)) in the entire 4.3 micron CO2 absorption band in the retrieval of temperature profiles T(p) during both day and night. Tropospheric sounding 15 micron CO2 observations were used primarily in the generation of clear column radiances (R(sub i)) for all channels. This new approach allowed for the generation of accurate Quality Controlled values of R(sub i) and T(p) under more stressing cloud conditions. Secondly, Version 5 contained a new methodology to provide accurate case-by-case error estimates for retrieved geophysical parameters and for channel-by-channel clear column radiances. Thresholds of these error estimates are used in a new approach for Quality Control. Finally, Version 5 contained for the first time an approach to provide AIRS soundings in partially cloudy conditions that does not require use of any microwave data. This new AIRS Only sounding methodology was developed as a backup to AIRS Version 5 should the AMSU-A instrument fail. Susskind et al 2010 shows that Version 5 AIRS Only sounding are only slightly degraded from the AIRS/AMSU soundings, even at large fractional cloud cover.

Susskind, Joel↗
NASA NTRS2011

Application of ESE Data and Tools to Air Quality Management: Services for Helping the Air Quality Community use ESE Data (SHAirED)

The goal of this REASoN applications and technology project is to deliver and use Earth Science Enterprise (ESE) data and tools in support of air quality management. Its scope falls within the domain of air quality management and aims to develop a federated air quality information sharing network that includes data from NASA, EPA, US States and others. Project goals were achieved through a access of satellite and ground observation data, web services information technology, interoperability standards, and air quality community collaboration. In contributing to a network of NASA ESE data in support of particulate air quality management, the project will develop access to distributed data, build Web infrastructure, and create tools for data processing and analysis. The key technologies used in the project include emerging web services for developing self describing and modular data access and processing tools, and service oriented architecture for chaining web services together to assemble customized air quality management applications. The technology and tools required for this project were developed within DataFed.net, a shared infrastructure that supports collaborative atmospheric data sharing and processing web services. Much of the collaboration was facilitated through community interactions through the Federation of Earth Science Information Partners (ESIP) Air Quality Workgroup. The main activities during the project that successfully advanced DataFed, enabled air quality applications and established community-oriented infrastructures were: develop access to distributed data (surface and satellite), build Web infrastructure to support data access, processing and analysis create tools for data processing and analysis foster air quality community collaboration and interoperability.

Falke, Stefan↗
NASA NTRS2022

Environmental Justice Needs-Assessment For Health & Air Quality: Assessing the Needs and Capacity of Organizations Working Towards Health and Environmental Justice Related to Health and Air Quality

Health and air quality are concerns in environmental justice (EJ) work, as air contaminants and their adverse health effects inequitably impact communities that are often underrepresented in research and litigation. Previously, the NASA DEVELOP National Program partnered with organizations that focus on a variety of health and air quality concerns and is now committed to partnering directly with EJ organizations to address inequities in health and air quality through the application of Earth observations. To support the establishment of future partnerships, DEVELOP is working to identify potential partners for further EJ research in the U.S. regarding health and air quality. This project conducted a needs assessment with EJ organizations to quantify their EJ involvement, geospatial capacity, and interest in collaborating with DEVELOP. A broad literature review identified multiple factors influencing health and air quality for potential DEVELOP projects: agriculture, heat, wildfires, industry and transportation infrastructure, and miscellaneous factors (e.g., burning, urban heat island effect, smoke plumes, truck exhaust, and noise). The needs assessment showed that 22% of the organizations interviewed were primarily concerned with transportation infrastructure, 21% with industry, 19% with heat, 10% with miscellaneous factors (e.g., resource mining, COVID-19), 8% with wildfires, 7% with agriculture, and 6% with resource mining. This will help inform the DEVELOP Program's pursuit of EJ projects relating to health and air quality. The team also created a directory for communities impacted by air pollutants to connect with geospatial resources and NASA Applied Sciences personnel for future EJ health and air quality work.

Elizabeth Duran↗
DOE OSTI2015

Cold Climate and Retrofit Applications for Air-to-Air Heat Pumps

Air source heat pumps (ASHP) including air-to-air ASHPs are easily applied to buildings almost anywhere for new construction as well as retrofits or renovations. They are widespread in milder climate regions but their use in cold regions is hampered due to low heating efficiency and capacity at cold outdoor temperatures. Retrofitting air-to-air ASHPs to existing buildings is relatively easy if the building already has an air distribution system. For buildings without such systems alternative approaches are necessary. Examples are ductless, minisplit heat pumps or central heat pumps coupled to small diameter, high velocity (SDHV) air distribution systems. This article presents two subjects: 1) a summary of R&D investigations aimed at improving the cold weather performance of ASHPs, and 2) a brief discussion of building retrofit options using air-to-air ASHP systems.

Baxter, Van D↗
DOE OSTI2024

The Effect of Air Separations on Fast Pyrolysis Products for Forest Residue Feedstocks

This study investigates the intricate relationship between biomass preprocessing and pyrolysis product yields, employing the air classification technique for the treatment of loblolly pine residues with varying moisture content. A comprehensive exploration of the physicochemical properties of air-classified loblolly pine informs a sophisticated pyrolysis simulation model. Given the complex and multifaceted nature of biomass pyrolysis, operating across diverse temporal and spatial scales, a pyrolysis kinetics-based CFD–DEM simulation method is employed to predict product yields. Results showed that the elevated moisture content amplifies particle adhesiveness, necessitating augmented air velocities for effective separation, thereby influencing the efficiency of the separation process. While carbon and hydrogen contents exhibit relative stability across diverse moisture contents and blower frequencies, the oxygen content undergoes noticeable changes. For example, the oxygen contents were measured as 29.2 and 38.6 wt% in the light fraction of 30% moisture content sample at blower frequencies of 10 and 20 Hz, respectively. An intriguing finding emerges from pyrolysis simulation, indicating that a lower blower frequency in air classification moderately enhances bio-oil yield and significantly improves its quality, particularly in terms of water content. For instance, the water content in the bio-oil was about 1.5% and 10% in the heavy and light fractions, respectively from 10% moisture sample under 15 Hz blower frequency. In summary, a detailed understanding and strategic manipulation of critical material attributes in biomass through efficient fractionation techniques are imperative for advancing fast pyrolysis as a sustainable avenue for renewable energy and chemical production.

09 BIOMASS FUELS↗
DOE OSTI2016

Modeling and Qualification of a Modified Emission Unit for Radioactive Air Emissions Stack Sampling Compliance

A planned laboratory space and exhaust system modification to the Pacific Northwest National Laboratory Material Science and Technology Building indicated a new evaluation of the mixing at the air sampling system location would be required for compliance to ANSI/HPS N13.1-2011. The modified exhaust system would add a third fan thereby increasing the overall exhaust rate out the stack thus voiding the previous mixing study. Prior to modifying the radioactive air emissions exhaust system, a three-dimensional computational fluid dynamics computer model was used to evaluate the mixing at the sampling system location. Modeling of the new original three-fan system indicated that not all mixing criteria could be met. A second modeling effort was conducted with the addition of an air blender downstream of the confluence of the three fans which then showed satisfactory mixing results. The final installation included an air blender, and the exhaust system underwent full-scale tests to verify velocity, cyclonic flow, gas, and particulate uniformity. The modeling results and those of the full-scale tests show agreement between each of the evaluated criteria. The use of a computational fluid dynamics code was an effective aid in the design process and allowed the sampling system to remain in its original location while still meeting the requirements for sampling at a well-mixed location.

atmospheric emissions, air monitoring, environment↗
DOE OSTI2023

Analysis of an Arctic cold air outbreak during autumn and related air mass transformations forced by surface changes and advection in higher altitudes

During marine cold air outbreaks (MCAOs), cold and dry Arctic air masses are transported from the central Arctic southward across the closed sea ice and much warmer open oceans. They experience significant transformations including a rapid heating and moistening, often leading to cloud formation. While intense wintertime MCAOs have been analyzed widely, the air mass transformations during other seasons have been studied sparsely. We address this gap by investigating an MCAO case observed in September 2020. To study the transformation processes, we combine the fifth generation of atmospheric reanalyses of the global climate (ERA5), trajectory calculations, as well as shipborne and airborne measurements. In the central Arctic, observations acquired from aboard the research vessel (RV) Polarstern during the Multidisciplinary drifting Observatory for the Study of Arctic Climate (MOSAiC) expedition characterized the initial state of the air mass over closed sea ice. Trajectories indicated the pathway the air mass took from RV Polarstern southward to the Fram Strait. For the first 24 h of the southbound drift, the air masses remained quasi-stationary. Then, still 15 h ahead of the marginal sea ice zone, differential advection across the boundary layer flow introduced humidity and clouds at higher altitudes between 1.5 and 2.5 km. ERA5-derived temperature and humidity tendencies indicated complex vertical interactions. Radiative cloud-top cooling, entrainment, and turbulence were significantly reduced in the lower and enhanced in the upper advected cloud layer. Eventually, the lower cloud deck dissipated. After this confluence of 2 different air masses, observations gathered by Polar 5 in Fram Strait as part of the MOSAiC Airborne observations in the Central Arctic campaign revealed cloudy, moist layers throughout the lowest 3.5 km and an increasing boundary layer height. Comparing the initial with the final state 48 h later, the largest net heating of +8 K was found close to the surface, yet the largest net moistening of +2.5 g kg -1 at an altitude of 1 km, as the initial profile was exceptionally dry here. We conclude that the observed air mass transformations were driven by the surface changes from sea ice to open ocean but additionally strongly impacted by the differential advection of clouds and moisture across the near-surface MCAO flow.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2017

Ultrathin Co 3 O 4 Layers with Large Contact Area on Carbon Fibers as High-Performance Electrode for Flexible Zinc-Air Battery Integrated with Flexible Display

A facile and binder-free method is developed for the in situ and horizontal growth of ultrathin mesoporous Co 3 O 4 layers on the surface of carbon fibers in the carbon cloth (ultrathin Co 3 O 4 /CC) as high-performance air electrode for the flexible Zn-air battery. In particular, the ultrathin Co 3 O 4 layers have a maximum contact area on the conductive support, facilitating the rapid electron transport and preventing the aggregation of ultrathin layers. The ultrathin feature of Co 3 O 4 layers is characterized by the transmission electron microscopy, Raman spectra, and X-ray absorption fine structure spectroscopy. Benefiting from the high utilization degree of active materials and rapid charge transport, the mass activity for oxygen reduction and evolution reactions of the ultrathin Co 3 O 4 /CC electrode is more than 10 times higher than that of the carbon cloth loaded with commercial Co 3 O 4 nanoparticles. Compared to the commercial Co 3 O 4 /CC electrode, the flexible Zn-air battery using ultrathin Co 3 O 4 /CC electrode exhibits excellent rechargeable performance and high mechanical stability. Furthermore, the flexible Zn-air battery is integrated with a flexible display unit. The whole integrated device can operate without obvious performance degradation under serious deformation and even during the cutting process, which makes it highly promising for wearable and roll-up optoelectronics.

cobalt oxides↗
DOE OSTI2020

From K‐O 2 to K‐Air Batteries: Realizing Superoxide Batteries on the Basis of Dry Ambient Air

Abstract Although using an air cathode is the goal for superoxide‐based potassium‐oxygen (K‐O 2 ) batteries, prior studies were limited to pure oxygen. Now, the first K‐air (dry) battery based on reversible superoxide electrochemistry is presented. Spectroscopic and gas chromatography analyses are applied to evaluate the reactivity of KO 2 in ambient air. Although KO 2 reacts with water vapor and CO 2 to form KHCO 3 , it is highly stable in dry air. With this knowledge, rechargeable K‐air (dry) batteries were successfully demonstrated by employing dry air cathode. The reduced partial pressure of oxygen plays a critical role in boosting battery lifespan. With a more stable environment for the K anode, a K‐air (dry) battery delivers over 100 cycles (>500 h) with low round‐trip overpotentials and high coulombic efficiencies as opposed to traditional K‐O 2 battery that fails early. This work sheds light on the benefits and restrictions of employing the air cathode in superoxide‐based batteries.

Qin, Lei↗
DOE OSTI2015

Analysis of activated air following high yield shots in the NIF

During the ignition experimental campaign, the National Ignition Facility (NIF) is expected to perform shots with varying fusion yield (up to 20 MJ or 7.1 x 10 18 neutrons per shot) and a maximum annual yield of 1200 MJ. A detailed MCNP model of the Target Bay (TB) and the two switchyards (SY) has been developed to estimate the post-shot radiation environment inside the facility. During D-T shots, a pulse of 14.1 MeV neutrons streaming outside the Target Chamber (TC) will activate the air present inside the TB and the argon gas inside the laser tubes. Smaller levels of activity are also generated in the SY air and in the argon portion of the SY laser beam path. The activated TB air will be mixed with fresh air from the Operations Support Building (OSB) before release through the stack. Flow of activated air from the Target Bay is controlled by the heating, ventilating, and air conditioning (HVAC) system. 16 N (T 1/2 = 7.13 s) dominates the radiation levels during the first minute following the shot. It is expected that 16 N will decay away during the confinement time before releasing the TB air through the stack. The other major contributors are 13 N (T 1/2 = 9.97 min) and 41 Ar (T 1/2 = 1.83 h). In general a low dose rate of < 1 μSv/h is expected near the stack during the first few hours following a 20 MJ shot. Here, the amount of activated Target Bay air released through the stack is very small and does not pose significant hazard to personnel or the environment. In the mean time, due to a very small leakage rate out of the laser tubes, the activated argon gas decays within the tubes and any resulting release to the environment is insignificant.

61 RADIATION PROTECTION AND DOSIMETRY↗
NASA NTRS1950

Penetration of Air Jets Issuing from Circular, Square, and Elliptical Orifices Directed Perpendicularly to an Air Stream

An experimental investigation was conducted to determine the penetration of air jets d.irected perpendicularlY to an air stream. Jets Issuing from circular, square, and. elliptical orifices were investigated. and. the jet penetration at a position downstream of the orifice was determined- as a function of jet density, jet velocity, air-stream d.enaity, air-stream velocity, effective jet diameter, and. orifice flow coeffIcient. The jet penetrations were determined for nearly constant values of air-stream density at three tunnel-air velocities arid for a large range of Jet velocities and. densities. The results were correlated in terms of dimensionless parameters and the penetrations of the various shapes were compared. Greater penetration was obtained. with the square orifices and the elliptical orifices having an axis ratio of 4:1 at low tunnel-air velocities and low jet pressures than for the other orifices investigated. The square orifices gave the best penetrations at the higher values of tunnel-air velocity and jet total pressure.

Ruggeri, Robert S.↗
NASA NTRS2006

The Atlanta Urban Heat Island Mitigation and Air Quality Modeling Project: How High-Resoution Remote Sensing Data Can Improve Air Quality Models

The Atlanta Urban Heat Island and Air Quality Project had its genesis in Project ATLANTA (ATlanta Land use Analysis: Temperature and Air quality) that began in 1996. Project ATLANTA examined how high-spatial resolution thermal remote sensing data could be used to derive better measurements of the Urban Heat Island effect over Atlanta. We have explored how these thermal remote sensing, as well as other imaged datasets, can be used to better characterize the urban landscape for improved air quality modeling over the Atlanta area. For the air quality modeling project, the National Land Cover Dataset and the local scale Landpro99 dataset at 30m spatial resolutions have been used to derive land use/land cover characteristics for input into the MM5 mesoscale meteorological model that is one of the foundations for the Community Multiscale Air Quality (CMAQ) model to assess how these data can improve output from CMAQ. Additionally, land use changes to 2030 have been predicted using a Spatial Growth Model (SGM). SGM simulates growth around a region using population, employment and travel demand forecasts. Air quality modeling simulations were conducted using both current and future land cover. Meteorological modeling simulations indicate a 0.5 C increase in daily maximum air temperatures by 2030. Air quality modeling simulations show substantial differences in relative contributions of individual atmospheric pollutant constituents as a result of land cover change. Enhanced boundary layer mixing over the city tends to offset the increase in ozone concentration expected due to higher surface temperatures as a result of urbanization.

Quattrochi, Dale A.↗
NASA NTRS2006

The Effect of the Saharan Air Layer on the Formation of Hurricane Isabel (2003) Simulated with AIRS Data

The crucial physics of how the atmosphere really accomplishes the tropical cyclogenesis process is still poorly understood. The presence of the Saharan Air Layer (SAL), an elevated mixed layer of warm and dry air that extends from Africa to the tropical Atlantic and contains a substantial amount of mineral dust, adds more complexity to the tropical cyclogenesis process in the Atlantic basin. The impact of the SAL on tropical cyclogenesis is still uncertain. Karyampudi and Carlson (1988) conclude that a strong SAL can potentially aid tropical cyclone development while Dunion and Velden (2004) argue that the SAL generally inhibits tropical cyclogenesis and intensification. Advancing our understanding of the physical mechanisms of tropical cyclogenesis and the associated roles of the SAL strongly depends on the improvement in the observations over the data-sparse ocean areas. After the Atmospheric Infrared Sounder (AIRS), the Advanced Microwave Sounding Unit (AMSU), and the microwave Humidity Sounder of Brazil (HSB) were launched with the NASA Aqua satellite in 2002, new data products retrieved from the AIRS suite became available for studying the effect of the warm, dry air mass associated with the SAL (referred to as the thermodynamic effect). The vertical profiles of the AIRS retrieved temperature and humidity provide an unprecedented opportunity to examine the thermodynamic effect of the SAL. The observational data can be analyzed and assimilated into numerical models, in which the model thermodynamic state is allowed to relax to the observed state from AIRS data. The objective of this study is to numerically demonstrate that the thermodynamic effect of the SAL on the formation of Hurricane Isabel (2003) can be largely simulated through nudging of the AIRS data.

Wu, iguang↗
NASA NTRS2009

Nitric Oxide and Oxygen Air-Contamination Effects on Extinction Limits of Non-Premixed Hydrocarbon-Air Flames for a HIFiRE Scramjet

Unique nitric oxide (NO) and oxygen air-contamination effects on the extinction Flame Strength (FS) of non-premixed hydrocarbon (HC) vs. air flames are characterized for 7 gaseous HCs, using a new idealized 9.3 mm straight-tube Opposed Jet Burner (OJB) at 1 atm. FS represents a laminar strain-induced extinction limit based on cross-section-average air jet velocity, Uair, that sustains combustion of a counter jet of gaseous fuel just before extinction. Besides ethane, propane, butane, and propylene, the HCs include ethylene, methane, and a 64 mole-% ethylene / 36 % methane mixture, the writer s previously recommended gaseous surrogate fuel for HIFiRE scramjet tests. The HC vs. clean air part of the work is an extension of a May 2008 JANNAF paper that characterized surrogates for the HIFiRE project that should mimic the flameholding of reformed (thermally- or catalytically-cracked) endothermic JP-like fuels. The new FS data for 7 HCs vs. clean air are thus consolidated with the previously validated data, normalized to absolute (local) axial-input strain rates, and co-plotted on a dual kinetically dominated reactivity scale. Excellent agreement with the prior data is obtained for all 7 fuels. Detailed comparisons are also made with recently published (Univ. Va) numerical results for ethylene extinction. A 2009-revised ethylene kinetic model (Univ. Southern Cal) led to predicted limits within approx. 5 % (compared to 45 %, earlier) of this writer s 2008 (and present) ethylene FSs, and also with recent independent data (Univ. Va) obtained on a new OJB system. These +/- 5 % agreements, and a hoped-for "near-identically-performing" reduced kinetics model, would greatly enhance the capability for accurate numerical simulations of surrogate HC flameholding in scramjets. The measured air-contamination effects on normalized FS extinction limits are projected to assess ongoing Arc-Heater-induced "facility test effects" of NO production (e.g., 3 mole-%) and resultant oxygen depletion (from 21 to 19.5 %), for testing the "64/36" surrogate fuel in Langley s Arc-Heated Scramjet Test Facility for HIFiRE engine designs. The FS results show a generally small (< 4 %) "nitric oxide enhancement" effect, relative to clean air, for up to 3 % NO (freestream Mach number up to 7 in Arc Jet testing). However, a progressively large "oxygendeficiency weakening" effect develops. For 3 % NO, a net weakening of 26 % in FS is derived for the "64/36" fuel vs. air. The corresponding net weakening for pure ethylene is 20 %. A number of practical recommendations regarding facility test effects are offered.

Pellett, Gerald L.↗