SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
By generating short stress pulses with thick transducers, the pulse-echo method for determining sound velocities and acoustic attenuation can be applied to thin specimens. The stress pulses enter a specimen where one pulse is reflected several times before a succeeding pulse enters the specimen.
The size of aluminum oxide particles produced by small rocket motors is determined by tank collection and spectrophotometry. The size of the particulate determines loss in thrust due to particle lag, particulate radiant heat transfer, acoustic attenuation and impingement and rocket plume structure and properties.
Theoretical model and acoustic attenuation measurements for inlet noise suppressors
Sound level measurements on noise sources on buses are used to observe the effects of attenuating acoustic pressure levels inside the bus by sound-proofing during complete repair. A spectral analysis of the sound level as a function of motor speed, bus speed along the road, and the category of the road is reported.
A continuous wave ultrasonic instrument capable of measuring very small changes in acoustic attenuation and phase velocity is described. This transmission oscillator ultrasonic spectrometer (TOUS) exhibits high sensitivity because it oscillates marginally. In spite of this high sensitivity, the TOUS system is relatively simple, compact, and inexpensive. These features suggest that the TOUS is suitable not only for precise laboratory measurements of the physical properties of materials, but also for field applications in nondestructive testing.
TOUS is capable for measuring very small changes in acoustic attenuation and phase velocity. Its high sensitivity to small changes in ultrasonic absorption results in part from operation under marginal conditions. In spite of high sensitivity, TOUS system is relatively simple, inexpensive, and compact.
The overall objectives of this program are to provide a more fire-resistant commercial aircraft interior and to improve the fuselage insulation barrier between the cabin interior and an exterior fuel fire. Significant secondary objectives are to reduce the smoke and toxic gas production of the materials and to meet the end item use requirements pertaining to wearability, color fastness, and aesthetic appeal. It is shown that the fuselage insulation materials must meet stringent requirements pertaining to acoustic attenuation, low density, and water repellency.
Standing wave ultrasonic techniques for the measurement of very small changes in acoustic attenuation and phase velocity are discussed. Enhanced sensitivity to these small changes was achieved by making the specimen part of a composite ultrasonic resonator. It was found that a point of maximum sensitivity on the response of such an ultrasonic resonator need not coincide with a point of maximum signal-to-error ratio. A model is presented and analyzed which takes into account error due to long term (low frequency) noise effects such as gain drifts and dc level shifts. This model yields a quantitative value for the signal-to-error ratio in which the signal is defined as the ideal change in the monitored response and the error as the difference between the experimentally measured change and the signal. The specific frequency dependent forms for the ultrasonic response and the sensitivity enhancement factor were used to predict the operating point on a mechanical resonance corresponding to maximum signal-to-error ratio.
This paper examines the technique of adapting an existing experiment to a Shuttle sortie mission. A sample cosmic-ray balloon experiment was studied to determine the feasibility of this cost-saving technique, which is applicable to a large spectrum of existing experiments, and to determine the programmatic impact and key problems. The main areas investigated include the determination of required modifications, steps in integration to the Spacelab/Shuttle, and the impact on orbital support and operations. One of the main problems in equipment adaptation is the acoustical loading during Shuttle boost; an environmental cover design presented herein shows a potential method to attain the required acoustic attenuation.
The described investigation is concerned with he development of a finite element scheme which can be used in a study of the acoustics of aircraft-engine ducts. In the absence of suitable variational principles for acoustic fluctuations within an aircraft fan engine, an acoustic analysis must proceed directly from the differential equations which describe compressible flow. The derived equations cannot be solved algebraically. The numerical technique used for solving them makes use of a linear rectangular element of a type considered by Zienkiewicz (1971). Attention is given to aspects of element derivation, the global matrix assembly, the solution of the matrix equation, questions of acoustic attenuation, and illustrations of the potential of the current model in duct optimization.
The acoustic attenuation of a sample of lunar basalt 70215 was measured by the method of sphere resonance. A Q of 1185 was achieved under a vacuum of 7 millionths torr after heating the sample. He and CO2 gas caused a small decrease of Q. H2O vapor, however, resulted in a major decrease in Q. The Q of lunar material when measured on earth is low because of adsorbed gases. However, it is not clear that this effect explains completely the observed high lunar Q.
A phase insensitive ultrasonic transducer which includes a CdS crystal that is annealed for a selected period of time and at a selected temperature to provide substantially maximum acoustic attenuation at the operating frequency of the transducer is described. Two electrodes are attached to the crystal with amplifier means and a signal processing system connected to one of the electrodes to provide an ultrasonic receiver.
A terpolyimide precursor was developed which can be foamed by microwave methods and yields foams possessing the best seating properties. A continuous process, based on spray drying techniques, permits production of polyimide powder precursors in large quantities. The constrained rise foaming process permits fabrication of rigid foam panels with improved mechanical properties and almost unlimited density characteristics. Polyimide foam core rigid panels were produced by this technique with woven fiberglass fabric bonded to each side of the panel in a one step microwave process. The fire resistance of polyimide foams was significantly improved by the addition of ceramic fibers to the powder precursors. Foams produced from these compositions are flexible, possess good acoustical attenuation and meet the minimum burnthrough requirements when impinged by high flux flame sources.
The behavior of acoustic attenuation in a solid is related to the electrical transmission line model where the electrical shunt conductance, which is frequency dependent, represents the loss due to the scattering sites in the solid. Results indicate that the absolute value of attenuation at a given frequency depends on both the normalized mean square deviation of the density and bulk modulus of the scattering sites from the ambient medium and the spatial scattering correlation function. Besides establishing the absolute value of attenuation, the spatial correlation function determines the attenuation profile as a function of frequency.
The one dimensional equations of gas dynamics are used to model subsonic acoustic choking. This model can accommodate non-linear distortion of waves and the eventual formation of shock waves. Several finite differencing schemes are adapted to obtain solutions. The results obtained with the various schemes are compared with the asymptotic results available. The results suggest that no one finite differencing scheme gives solutions significantly better than the others and that most of the difference solutions are close to the asymptotic results. If the acoustic shock wave is sufficiently strong it almost annihilates the acoustic wave; in this situation numerical errors may dominate the results. Such solutions involve very large acoustic attenuations.
Acoustic attenuation measurements in air were analyzed in order to estimate the second coefficient of viscosity. Data over a temperature range of 11 C to 50 C and at relative humidities between 6 percent and 91 percent were used. This analysis showed that the second coefficient of viscosity varied between 1900 and 20,000 times larger than the dynamic or first coefficient of viscosity over the temperature and humidity range of the data. In addition, the data showed that the molecular relaxation effects, which are responsible for the magnitude of the second coefficient of viscosity, place severe limits on the use of time-independent, thermodynamic equations of state. Compressible flows containing large streamwise velocity gradients, like shock waves, which cause significant changes in particle properties to occur during time intervals shorter than hundredths of seconds, must be modeled using dynamic equations of state. The dynamic model approach is described briefly.
The requirements for the Laser Atmospheric Wind Sounder (LAWS) were determined from system considerations and are summarized in tabular form. The laser subsystem provides for the generation and frequency control of two beams, the transmit high power and local oscillator beams, which are delivered to the optical and receiver subsystems, respectively. In our baseline approach, the excitation of the gain section is achieved by a self-sustaining uv-(corona) preionized discharge. Gas is recirculated within the laser loop using a transverse flow fan. An intra-flow-loop heat exchanger, catalyst monolith, and acoustic attenuators condition the gas to ensure uniform energy output and high beam quality during high pulse repetition rate operation. The baseline LAWS laser pulse temporal profile as calculated by in-house laser codes is given in graphical form.
Lead(II) bromide was purified by a combination of directional freezing and zone-refining methods. Differential thermal analysis of the lead bromide showed that a destructive phase transformation occurs below the melting temperature. This transformation causes extensive cracking, making it very difficult to grow a large single crystal. Energy of phase transformation for pure lead bromide was determined to be 24.67 cal/g. To circumvent this limitation, crystals were doped by silver bromide which decreased the energy of phase transformation. The addition of silver helped in achieving the size, but enhanced the inhomogeneity in the crystal. The acoustic attenuation constant was almost identical for the pure and doped (below 3000 ppm) crystals.