Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Economic considerations of utilizing small wind generators

The economic feasibility of small wind generators is compared to that of solar cells, primary batteries, thermoelectric generators, and engine generators. It is shown that small wind generator plants offer an attractive alternative to primary battery systems and constantly running engines to generate power in remote areas. The limitation is an annual average wind velocity of at least 9 to 10 mph. Presently available units are most useful in the average load range of 10 to 1000 watts.

Dodge, R.↗
DOE OSTI2016

An Investigation of Passive and Semi-Active Tuned Mass Dampers for a Tension Leg Platform Floating Offshore Wind Turbine in ULS Conditions

Offshore Wind Turbines (OWTs) are subjected to complex external loadings caused by combined wind and wave sources. The application of structural damping control techniques to OWTs using Tuned Mass Dampers (TMDs) has shown to be effective in reducing the integrated system loads and accelerations. In this work, the impact of passive and semi-active (S-A) TMD’s applied to both fixed-bottom (monopile) and floating (tension leg platform) OWTs are evaluated under the Fatigue Limit State (FLS) and Ultimate Limit State (ULS). Different S-A control logics like ON/OFF state damping based on the ground hook (GH) control policy are implemented, and the frequency response of each algorithm is investigated. It is shown that the performance of each algorithm varies according to the load conditions such as FLS (normal operation) and ULS (idling state). Fully-coupled time domain simulations are conducted through the developed simulation tool for structural control integrated into the high-fidelity wind turbine design code, FASTv8. Compared to the passive TMD, it is shown that a S-A TMD results in higher load reductions, as well as, smaller strokes under both FLS and ULS conditions. In FLS analysis, the S-A TMD using Displacement Based Ground Hook (DB-GH) control is capable of reducing the fore-aft and side-to-side damage equivalent loads for the monopile substructure by approximately 12 % and 64 %, respectively. The ultimate loads at the tower base for the floating substructure (TLP) are also reduced by 9% with S-A TMD followed by Inverse Velocity Based Ground Hook control (IVB-GH). The dynamic characteristics and practical feasibility of a magnetorheological (MR) damper (for S-A control) are also evaluated.

17 WIND ENERGY↗
DOE OSTI2021

Challenges, opportunities, and a research roadmap for downwind wind turbines

This study investigates the challenges and opportunities presented by downwind wind turbines and offers a roadmap of future research pathways to maximize their potential. Multidisciplinary design, analysis, and optimization comparison studies between upwind and downwind configurations on a modern 10-MW offshore wind turbine are presented to support the discussion. On one hand, the downwind rotor is found to consistently have a smaller swept area under loading. As a result, the downwind design produces less annual energy production (-1.2%). On the other hand, lighter blades for the downwind configuration lead to lower capital costs (-1.7%), so there is little difference in the levelized cost of energy between the two. Key ultimate and fatigue loads are compared, with some values increasing in the downwind configuration, while others decrease. The impact of a downwind configuration on the tower and the impacts of cone and tilt angles and free-yaw system on the levelized cost of energy are also investigated. The results show a mix of some advantages and disadvantages. Given these results, four areas of research in advanced controls, highly tilted rotors, higher fidelity aerodynamic models, and floating wind are proposed for downwind wind turbines.

17 WIND ENERGY↗
DOE OSTI2019

Evaluating commercial feasibility of a new tall wind tower design concept using a stochastic levelized cost of energy model

Wind power generation has seen a dramatic increase in the 21st century and the Department of Energy (DOE) envisions that wind energy will become a much larger part of overall power generation in the U.S. by 2050. Wind turbines have continued to grow in size during the last few decades with towers commonly built at a height of 80 m for typical utility-scale turbines in the Unites States, and this is accompanied by certain transportation and logistics challenges. The newly proposed tall tower technology has been designed to be cost-effective in assembling towers as high as 140 m from precast concrete module components that are capable of transport on the U.S. road system. This paper presents an alternative wind tower design with potential for reducing the overall levelized cost of energy (LCOE); it evaluates a hexagonal precast concrete wind tower solution that facilitates use of a taller wind turbine generator for harvesting stronger, steadier, and more frequent wind resources to increase wind energy production and lower the overall LCOE. An integrated team of industry experts was consulted to support development of a stochastic life cycle cost model using a parametric estimate of the cost and fabrication and assembly schedules of this new wind tower design concept as well as forecasting the projected revenue to be created by the new technology. The study concludes that this new design concept is a commercially viable solution, with an estimated LCOE savings ranging from 2% to 4% compared with the typical 80 m turbine deployed in the United States, and it also provides wind power potential to previously untapped regions in the country. This article helps to inform energy developers, manufacturers, and policy makers, both regionally and nationally, of a possible economically feasible wind tower design solution.

17 WIND ENERGY↗
DOE OSTI2026

Modulation induced by very-large-scale motions on the inclination angle of wall-attached eddies: an atmospheric surface layer experiment

The forward leaning inclination angle, 𝛾, of coherent turbulent structures is a well-known feature of wall-bounded turbulent flows. Although invariant across friction Reynolds numbers within the range 𝑅𝑒 𝜏 =10 3 −10 6 , 𝛾 can vary significantly across turbulent scales within a high-Reynolds-number flow. Very-large-scale motions (VLSMs) are known to induce significant changes in the instantaneous shear profile, which is a conditioning event that could trigger variability in the inclination angle of smaller coherent turbulent structures. Although this aspect has been extensively studied via numerical and laboratory experiments, few studies have explored this feature for a very-high-Reynolds-number atmospheric flow. In this work, the inclination angle of turbulent structures within the atmospheric surface layer at a very high Reynolds number (𝑅𝑒 𝜏 =7.9 ×10 5 ) is investigated by deploying a scanning Doppler light detection and ranging and a super large particle image velocimetry (SLPIV) apparatus. The inclination angle of wall-attached eddies is inferred either from the two-point correlation of streamwise velocity (𝛾 =41.1∘) or with a scale-dependent approach through the spectral linear stochastic estimator (SLSE). The SLSE (and, thus, the scale-dependent inclination angle) is conditionally evaluated based on the high- and low-momentum events induced by VLSMs, both in the streamwise (𝑢′𝑉𝐿𝑆𝑀) and in the vertical (𝑤′ 𝑉𝐿𝑆𝑀) velocity components. As a result, lower inclination angles (𝛾 =30° −50°) are found for 𝑢$^{'}_{VLSM}$ >0 (𝑤$^{'}_{VLSM}$ <0), while higher values (50° −85°) are ascribed to 𝑢$^{'}_{VLSM}$ <0 (𝑤$^{'}_{VLSM}$ >0). This result emphasises the primary role that VLSMs play in shaping the wall-attached eddy geometry, which, in turn, is crucial to determine the Reynolds stress balance within the wall-attached eddy range.

42 ENGINEERING↗
DOE OSTI2019

Superlubricity in rolling/sliding contacts

Rolling element bearings and gears are critical components of mechanical systems such as wind turbines and automotive engines and transmissions that use oil-based lubricants. Oil-based lubricants used in these applications many times needs periodical replacement, which not only add more cost but also affects overall productivity. More importantly, the used oil generates hazardous waste creating huge environmental problem. In this study, we demonstrated that nanomaterials can be employed as solid lubricants in combination with diamond like carbon (DLC) films in dry nitrogen environment under rolling/sliding contacts. Using micro-pitting rig (MPR) that generally used to test and qualify materials and lubricants for bearings and gear systems for industrial applications, we have tested diamond like carbon (DLC) material pairs in an oil-free, dry nitrogen environment along with two dimensional (2D) MoS2 combined with nanodiamond as a solid lubricant. We show that superlubricity (traction coefficient of friction is 0.003) was achieved through the formation of a carbon rich superlubricious tribolayer at the interface reducing the overall friction by a minimum of 20 times and no surface damage as compared to Steel-Steel contacts lubricated with oil (0.06-0.07). The current work paves the way for developing oil-free solid lubricants in a variety of applications involving rolling/sliding contacts.

36 MATERIALS SCIENCE↗
DOE OSTI2019

FAST Model Calibration and Validation of the OC5-DeepCwind Floating Offshore Wind System Against Wave Tank Test Data

During the Offshore Code Comparison Collaboration, Continued, with Correlation (OC5) project, which focused on the validation of numerical methods through comparison against tank test data, the authors created a numerical FAST model of the 1:50-scale DeepCwind semisubmersible system that was tested at the Maritime Research Institute Netherlands ocean basin in 2013. The OC5 project revealed a general underprediction of loads and motions by the participating numerical models. This paper discusses several model calibration studies that were conducted to identify potential model parameter adjustments that help to improve the agreement between the numerical simulations and the experimental test data. These calibration studies cover wind-field-specific parameters (coherence, turbulence), and hydrodynamic and aerodynamic modeling approaches, as well as rotor model (blade-pitch and blade-mass imbalances) and tower model (structural tower damping coefficient) adjustments. These calibration studies were conducted based on relatively simple calibration load cases (wave only/wind only). The agreement between the final FAST model and experimental measurements is then assessed based on more complex combined wind and wave validation cases. The analysis presented in this paper does not claim to be an exhaustive parameter identification study but is aimed at describing the qualitative impact of different model parameters on the system response. This work should help to provide guidance for future systematic parameter identification and uncertainty quantification efforts.

17 WIND ENERGY↗
DOE OSTI2025

Design, Optimization, and Control of Floating Offshore Wind Farms for Optimal Energy Production (Final report)

The uncertainty and irregularity of ocean waves and the ocean environment is a major factor in the development of commercial scale floating wind turbines as the operation of floating structures in such an environment can lead to irregular and unpredictable loading, fatigue, and ultimately a reduction in the operational life of the turbine system which affects energy production over the lifetime of the turbine. Control solutions that can limit float motions and mitigate stressful events on the structure become essential for extending lifetime and limiting the operational uncertainty of a floating wind turbine. Digital twins are computational replicas of physical systems that operate in parallel with the operation of the physical system. Given advanced knowledge of a systems input, digital twins have the ability to predict the behavior of a system in advance, which can be valuable in the control of that system. In this project, we developed and assessed potential digital twin models developed in house and openly available (OpenFast) for use in the real time control of the six degree of freedom response motions of a floating wind turbine in ocean waves. Coupling these models with near-field real time irregular sea surface (wve) measurement/sensings and prediction models, we used the digital twin to predict how the floating turbine will respond to the incoming waves. Applying this information to a motion control system of the float, one can limit and control float motions to prevent undesirable loading events/large angular motions, thus increasing system life and ultimately contributing to optimizing energy production. Due to the computational intensity of operating a digital twin in real time, we investigated the use of artificial intelligence techniques to speed-up the processes of the digital twin, as well as the wave reconstruction/prediction models. Model tank testing at the University of Rhode Island and University of Maine both validated and demonstrated the developed techniques on simple float geometries and a scale model of the NREL 15 MW reference turbine.

17 WIND ENERGY↗
DOE OSTI2025

INTEGRATE – Inverse Network Transformations for Efficient Generation of Robust Airfoil and Turbine Enhancements

The INTEGRATE (Inverse Network Transformations for Efficient Generation of Robust Airfoil and Turbine Enhancements) project developed a new inverse-design capability for the aerodynamic design of wind turbine rotors using invertible neural networks. Training data was obtained from improved turbulence and transition models for RANS and hybrid RANS/LES solvers with machine-learned physics-based data-augmented corrections and then using the resulting neural-network(s) augmented RANS model to run thousands of 2-D and 3-D CFD simulations.

17 WIND ENERGY↗
DOE OSTI2026

BIL GRID-READY WIND: Reliable and Economical Grid Services Design, Implementation, and Demonstration at the Great Pathfinder Wind Power Plant

The GRID-READY WIND project aimed to demonstrate the ability of utility-scale wind power plants (WPPs) to deliver traditional and emerging grid services (GSs) in both grid-following (GFL) and grid-forming (GFM) modes through a centralized control framework, supplemented by local control adjustments at the wind turbine generator as needed. Throughout the project, the team offered recommendations on how the grid services demonstrated with WPPs could be applied to other inverter-based resources (IBRs), such as photovoltaic (PV) systems and battery energy storage systems (BESS), while considering the unique dynamics of these resources arising from their energy generation characteristics. The project sought to enhance the confidence of system operators (SOs) and planners in utilizing WPPs, alongside other IBRs such as PV plants and BESS, to provide essential grid services over extended periods under diverse operating conditions, thereby supporting their integration into the bulk power system.

17 WIND ENERGY↗
DOE OSTI2023

Characterization of wind turbine flow through nacelle-mounted lidars: a review

This article provides a comprehensive review of the most recent advances in the planning, execution, and analysis of inflow and wake measurements from nacelle-mounted wind Doppler lidars. Lidars installed on top of wind turbines provide a holistic view of the inflow and wake characteristics required to characterize and optimize wind turbine performance, carry out model validation and calibration, and aid in real-time control. The need to balance the enhanced capabilities and limitations of lidars compared to traditional anemometers inspired a broad variety of approaches for scan design and wind reconstruction, which we discuss in this review. We give particular emphasis to identifying common guidelines and gaps in the available literature with the aim of providing an exhaustive picture of the state-of-the-art techniques for reconstructing wind plant flow using nacelle-mounted lidars.

17 WIND ENERGY↗
NASA NTRS1975

Maximum lift of upper surface blowing STOL aircraft with swept wings

In a recent large scale wind tunnel investigation of a 4 engine upper surface blowing configuration in the Ames 40- by 80-Foot Wind Tunnel, the large nacelles extending well above the wing upper surface had a sizable adverse effect on maximum lift. The presence of the nacelles produced high upwash angles between the nacelles and near the fuselage. The severity and alleviation of this problem is discussed with the use of calculated spanwise loadings. The combined effects of wing leading edge stall control, wing sweep, and nacelle cross section modification were considered in maximum lift improvement. Experimental results of these effects are presented.

Koenig, D. G.↗
NASA NTRS1976

Simulation of Flight-Type Engine Fan Noise in the NASA-Lewis 9X15 Anechoic Wind Tunnel

Flight type noise as contrasted to the usual ground static test noise exhibits substantial reductions in the time unsteadiness of tone noise, and in the mean level of tones calculated to be nonpropagating or cut-off. A model fan designed with cuttoff of the fundamental tone was acoustically tested in the anechoic wind tunnel under both static and tunnel flow conditions. The properties that characterize flight type noise were progressively simulated with increasing tunnel flow. The distinctly lobed directivity pattern of propagating rotor/stator interaction modes was also observed. Excess noise attributed to the ingestion of the flow disturbances that prevail near most static test facilities is substantially reduced with tunnel flow.

Heidmann, M. F.↗