Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “variational principles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

The Solar Energetic Particle Event of December 14, 2006

We report on observations of a solar energetic particle event by instruments on five different spacecraft: the Advanced Composition Explorer (ACE), STEREO A and B, WIND, and GOES II. The event began with a class X1.5 .soft x-ray flare in AR930 on December 14 at 22:15 UT. At this time the two STEREO spacecraft were located outside the Earth's magnetosphere and were heading for their first lunar swing-by on December 15. The x-ray event was located on the sun at W46, a longitude which is nominally well-connected magnetically to the Earth. An interplanetary shock, associated with an earlier X3.4 event on December 13 (also from AR930), passed the Earth on December 14 at approx.13:56 (time at ACE). The corresponding magnetic cloud arrived at approx.22 UT on December 14, close to the time of the onset of the particle event associated with the X1.5 flare, and extended until approx.08 UT on December 15. The intensity of approx.14 MeV protons at STEREO A shows three dips by factors of approx.10 or more during the early stages of this event while the spacecraft was within the magnetic cloud. Similar dips are seen for protons to at least 100 MeV. In principle, these dips could have been caused by changes in the magnetic field direction with respect to the particle telescope's field of view while viewing a beamed particle distribution. However, this possibility can be ruled out because the magnetic field at the spacecraft shows no evidence of such directional variations, and similar particle intensity dips were seen by instruments on other spacecraft in the near-Earth solar wind. We shall present evidence that the dips were actually associated with varying magnetic connection to the Sun within the magnetic cloud. These dips were not observed at GOES II, suggesting they were somehow smoothed out by passage into the magnetosphere.

vonRosenvinge, T. T.↗
NASA NTRS2011

Superpixel-Augmented Endmember Detection for Hyperspectral Images

Superpixels are homogeneous image regions comprised of several contiguous pixels. They are produced by shattering the image into contiguous, homogeneous regions that each cover between 20 and 100 image pixels. The segmentation aims for a many-to-one mapping from superpixels to image features; each image feature could contain several superpixels, but each superpixel occupies no more than one image feature. This conservative segmentation is relatively easy to automate in a robust fashion. Superpixel processing is related to the more general idea of improving hyperspectral analysis through spatial constraints, which can recognize subtle features at or below the level of noise by exploiting the fact that their spectral signatures are found in neighboring pixels. Recent work has explored spatial constraints for endmember extraction, showing significant advantages over techniques that ignore pixels relative positions. Methods such as AMEE (automated morphological endmember extraction) express spatial influence using fixed isometric relationships a local square window or Euclidean distance in pixel coordinates. In other words, two pixels covariances are based on their spatial proximity, but are independent of their absolute location in the scene. These isometric spatial constraints are most appropriate when spectral variation is smooth and constant over the image. Superpixels are simple to implement, efficient to compute, and are empirically effective. They can be used as a preprocessing step with any desired endmember extraction technique. Superpixels also have a solid theoretical basis in the hyperspectral linear mixing model, making them a principled approach for improving endmember extraction. Unlike existing approaches, superpixels can accommodate non-isometric covariance between image pixels (characteristic of discrete image features separated by step discontinuities). These kinds of image features are common in natural scenes. Analysts can substitute superpixels for image pixels during endmember analysis that leverages the spatial contiguity of scene features to enhance subtle spectral features. Superpixels define populations of image pixels that are independent samples from each image feature, permitting robust estimation of spectral properties, and reducing measurement noise in proportion to the area of the superpixel. This permits improved endmember extraction, and enables automated search for novel and constituent minerals in very noisy, hyperspatial images. This innovation begins with a graph-based segmentation based on the work of Felzenszwalb et al., but then expands their approach to the hyperspectral image domain with a Euclidean distance metric. Then, the mean spectrum of each segment is computed, and the resulting data cloud is used as input into sequential maximum angle convex cone (SMACC) endmember extraction.

Thompson, David R.↗
NASA NTRS2021

An Efficient and Accurate Algorithm for Computing Grid-Averaged Solar Fluxes for Horizontally Inhomogeneous Clouds

A computationally efficient method is presented to account for the horizontal cloud inhomogeneity by using a radiatively equivalent plane parallel homogeneous (PPH) cloud. The algorithm can accurately match the calculations of the reference (rPPH) independent column approximation (ICA) results, but use only the same computational time required for a single plane parallel computation. The effective optical depth of this synthetic sPPH cloud is derived by exactly matching the direct transmission to that of the inhomogeneous ICA cloud. The ffective9 scattering asymmetry factor is found from a pre-calculated albedo inverse look-up-table that is allowed to vary over the range from -1.0 to 1.0. In the special cases of conservative scattering and total absorption, the synthetic method is exactly equivalent to the ICA, with only a small bias (about 0.2% in flux) relative to ICA due to imperfect interpolation in using the look-up tables. In principle, the ICA albedo can be approximated accurately regardless of cloud inhomogeneity. For a more complete comparison, the broadband shortwave albedo and transmission calculated from the synthetic sPPH cloud and averaged over all incident directions, have the RMS biases of 0.26% and 0.76%, respectively, for inhomogeneous clouds over a wide variation of particle size. The advantages of the synthetic PPH method are that (1) it is not required that all the cloud subcolumns have uniform microphysical characteristic, (2) it is applicable to any 1D radiative transfer scheme, and (3) it can handle arbitrary cloud optical depth distributions and an arbitrary number of cloud subcolumns with uniform computational efficiency.

cloud inhomogeneity↗
NASA NTRS1986

Distributions of (C-13)O emission in the disks of late-type spiral galaxies

In studies of molecular clouds in external galaxies, the distribution of (C-12)O emissivity as a function of radius in a galaxy has been employed to infer the surface density of molecular hydrogen with galactocentric radius. In principle, observations of more optically thin molecular species, such as (C-13)O, can be used as an alternative tracer of the mass of molecular hydrogen in a galaxy. Since the (C-13)O lines have a much lower opacity than the saturated, nearly thermalized (C-12)O lines, their intensity variations as a function of galactocentric radius are more readily interpreted in terms of gas density variations. The first strip maps of the (C-13)O distributions in six spiral galaxies are presented, and the (C-13)O and (C-12)O radial distributions are compared. Attention is given to the reliability of H2 masses and H2 distributions derived from (C-12)O data.

Young, J. S.↗
NASA NTRS1993

Topographic mapping using a monopulse SAR system

Terrain height variations in mountainous areas cause two problems in the radiometric correction of SAR images: the first being that the wrong elevation angle may be used in correcting for the radiometric variation of the antenna pattern; the second that the local incidence angle used in correcting the projection of the pixel area from slant range to ground range coordinates may vary from that given by the flat earth assumption. We propose a novel design of a SAR system which exploits the monopulse principle to determine the elevation angle and thus the height at the different parts of the image. The key element of such a phase monopulse system is an antenna, which can be divided into a lower and upper half in elevation using a monopulse comparator. In addition to the usual sum pattern, the elevation difference pattern can be generated by a -pi phase shift on one half of the antenna. From the ratios of images radiometrically modulated by the difference and sum antenna pattern in cross-track direction, we can derive the appropriate elevation angle at any point in the image. Together with the slant range we can calculate the height of the platform above this point using information on the antenna pointing and the platform attitude. This operation, repeated at many locations throughout the image, allows us to build up a topographic map of the height of the aircraft above each location. Inversion of this map, using the precisely determined aircraft altitude and the accurate flight path, leads to the actual topography of the imaged surface. The precise elevation of one point in the image could also be used to convert the height map to a topographic map. In this paper, we present design considerations for a corresponding airborne SAR system in X-Band and give estimates of the error due to system noise and azimuth ambiguities as well as the expected performance and precision in topographic mapping.

Zink, M.↗
NASA NTRS1925

Standardization Tests of NACA No. 1 Wind Tunnel

The tests described in this report were made in the 5-foot atmospheric wind tunnel of the National Advisory Committee for Aeronautics, at Langley Field. The primary objective of collecting data on the characteristics of this tunnel for comparison with those of others throughout the world, in order that, in the future, the results of tests made in all the principle laboratories may be interpreted, compared, and coordinated on a basis of scientifically established relationships, a process hitherto impossible due to the lack of comparable data. The work includes tests of a disk, spheres, cylinders, and airfoils, explorations of the test section for static pressure and velocity distribution, and determination of the variations of air flow direction throughout the operating range of the tunnel. (author)

Reid, Elliott G↗
NASA NTRS1995

Preliminary large-eddy simulations of flow around a NACA 4412 airfoil using unstructured grids

Large-eddy simulation (LES) has matured to the point where application to complex flows is desirable. The extension to higher Reynolds numbers leads to an impractical number of grid points with existing structured-grid methods. Furthermore, most real world flows are rather difficult to represent geometrically with structured grids. Unstructured-grid methods offer a release from both of these constraints. However, just as it took many years for structured-grid methods to be well understood and reliable tools for LES, unstructured-grid methods must be carefully studied before we can expect them to attain their full potential. In the past two years, important building blocks have been put into place making possible a careful study of LES on unstructured grids. The first building block was an efficient mesh generator which allowed the placement of points according to smooth variation of physical length scales. This variation of length scales is in all three directions independently, which allows a large reduction in points when compared to structured-grid methods, which can only vary length scales in one direction at a time. The second building block was the development of a dynamic model appropriate for unstructured grids. The principle obstacle was the development of an unstructured-grid filtering operator. In the past year, some of the new filters developed by Jansen have been implemented into a highly parallelized finite element code based on the Galerkin/least-squares finite element method. We have chosen the NACA 4412 airfoil at maximum lift as the first simulation for a variety of reasons. First, it is a problem of significant interest since it would be the first LES of an aircraft component. Second, this flow has been the subject of three experimental studies. The third reason for considering this flow is the variety of flow features which provide an important test of the dynamic model. Only the dynamic model can be expected to perform satisfactorily in this variety of situations: from the laminar regions where it must not modify the flow at all to the turbulent boundary layers and wake where it must represent a wide variety of subgrid-scale structures. The flow configuration we have chosen is that of Wadcock (1987) at Reynolds number based on chord Re(sub c) = u(sub infinity)c/v = 1.64 x 10(exp 6), Mach number M = 0.2, and 12 deg angle of attack.

Jansen, Kenneth↗
NASA NTRS1984

Calculations of turbulent mass transport in a bluff-body diffusion-flame combustor

Experimental measurements of turbulent mass transit in a bluff-body diffusion-flame combustor (using CO2 instead of fuel) are analyzed to evaluate the accuracy of physical models used in flow computations. The data of Lightman and Magill (1981), Lightman et al. (1983), and Roquemore et al. (1983) are used to calculate apparent turbulent Schmidt numbers (TSN) for a series of flow conditions by a modified TEACH viscous-flow code. The modeling principles, calculation grid, and boundary conditions are discussed, and the results are presented in graphs comparing calculated and measured values. It is shown that models such as the two-equation (K - epsilon) model which use a single value of the TSN are inappropriate for conditions typical of gas-turbine combustors: local TSN variations due to turbulence behavior must be taken into account in improved models.

Sturgess, G. J.↗
NASA NTRS1994

An estimate of the momentum deposition in the lower thermosphere by the observed diurnal tide

This paper reports a calculation of the acceleration of the zonal mean flow induced by dissipating tides in the equatorial lower thermosphere. Estimates of the gravest symmetric gravitiational Hough mode (1,1) of the migrating diurnal tide are obtained from monthly composites of global winds observed by the Upper Atmosphere Research Satellite (UARS) High Resolution Doppler Imager (HRDI). Using the principles of classical tidal theory, the tidal momentum flux divergence is computed for a series of monthly mean (1,1) fields from January 1992 to May 1993. The contribution to the mean flow by the leading mode of the migrating tide ranges between -5 and -20 (easterly) m/s/day in the equatorial lower thermosphere. A semiannual variation is noted in the tidal amplitudes and the inferred tidal accelerations. These variations are consistent with observed trends in the zonal mean flow of the lower thermosphere.

Lieberman, Ruth S.↗
NASA NTRSDate not supplied

Governing Data Findability, Accessibility, Interoperability and Reusability (FAIR) Compliance

The most recent data strategy documents at both the federal and NASA levels stipulate that systems should strive for the data they manage to be Findable, Accessible, Interoperable, and Reusable (FAIR). The NASA Life Sciences Portal (NLSP) has already begun leading efforts in this area for HRP, initiating efforts to comply with the FAIR principles. The broad interpretation of the FAIR principles has led to a plethora of tools that use a splay of metrics specifically but variably developed to judge how compliant data and systems are with the principles. A recent review [3] identified and studied 1,180 metrics across 20 publicly available tools for checking FAIR compliance of data and systems. Because of their very recent development, many organizations and data systems managers and developers have not yet had adequate time or resources to understand these FAIR compliance tools and metrics, their variations in design, accuracy or ease of application to their specific data sets and systems. Thus, it would be best for larger organizations like NASA to approach formulating a strategy for governance of FAIR compliance that can be flexibly applied and is adaptable to an evolving awareness knowledge of FAIR compliance methods and tools. In September 2024, the NASA Science Mission Directorate(SMD) organized a workshop on NASA science data repositories, including the topics of implementing FAIR and governing FAIR compliance across SMD. The initial part of these FAIR discussions focused on developing consensus around required science metadata fields. This is challenging given the diverse nature of NASA’s scientific data portfolio, the variety of metadata models and vocabularies used, and variable level of resources available to curate these data. Later discussion focused on three possible approaches to governing FAIR compliance: distributed, in which various programs, projects or systems define their own methods for assessing FAIR compliance, reporting results up appropriate management lines; centralized, in which higher-level organization(s) specify compliance tools or methods for the various data systems; and multi-level, in which a group comprised of individuals with expertise from multiple levels with organizations is formed to provide guidance and/or specifications for governing FAIR compliance. We report on the recommendations this session yielded, and how these might be shaped specifically to help implement and govern the compliance with FAIR of Human Research Program data and systems.

governance↗
NASA NTRS1992

Diagnosing ocean energy transports from earth radiation budget measurements

The maximum energy production (MEP) principle suggested by Paltridge (1975) is applied to separate the satellite-inferred required total transports into the atmospheric and the oceanic components within a two-dimensional (2D) framework. For this purpose, the required 2D energy transports (Sohn and Smith, 1991) are imposed on Paltridge's energy balance model which is then solved as a variational problem. The results provide separated atmospheric and oceanic transports on a 2D basis such that the total divergence is equal to the net radiation measured from a satellite.

Sohn, Byung-Ju↗
NASA NTRS1980

Dynamics and control of a continuum model for a solar power system

An approach for modeling dynamic equations of motion of a plate attached with rigid bodies is presented. The equations of motion are developed using the principle of virtual work. Lagrange multipliers are used as interaction forces and/or moments to maintain prescribed constraints which is the basis of the interconnection between the plate and rigid bodies. The overall approach is unique in the sense that a continuous model described by a family of partial differential equations is established. An approximate formulation by using variational method is established yielding a solution compatible with the assumed degree of approximation. The formulation is useful particularly when parametric study of dynamic response for a satellite power system is desired. As an example, an approximate governing equation of algebraic eigenvalue problem is given for a dual microwave power transmission system. Controller design is discussed.

Juang, J. N.↗
NASA NTRS1998

Computational Study of Surface Tension and Wall Adhesion Effects on an Oil Film Flow Underneath an Air Boundary Layer

The fringe-imaging skin friction (FISF) technique, which was originally developed by D. J. Monson and G. G. Mateer at Ames Research Center and recently extended to 3-D flows, is the most accurate skin friction measurement technique currently available. The principle of this technique is that the skin friction at a point on an aerodynamic surface can be determined by measuring the time-rate-of-change of the thickness of an oil drop placed on the surface under the influence of the external air boundary layer. Lubrication theory is used to relate the oil-patch thickness variation to shear stress. The uncertainty of FISF measurements is estimated to be as low as 4 percent, yet little is known about the effects of surface tension and wall adhesion forces on the measured results. A modified version of the free-surface Navier-Stokes solver RIPPLE, developed at Los Alamos National Laboratories, was used to compute the time development of an oil drop on a surface under a simulated air boundary layer. RIPPLE uses the volume of fluid method to track the surface and the continuum surface force approach to model surface tension and wall adhesion effects. The development of an oil drop, over a time period of approximately 4 seconds, was studied. Under the influence of shear imposed by an air boundary layer, the computed profile of the drop rapidly changes from its initial circular-arc shape to a wedge-like shape. Comparison of the time-varying oil-thickness distributions computed using RIPPLE and also computed using a greatly simplified numerical model of an oil drop equation which does not include surface tension and wall adhesion effects) was used to evaluate the effects of surface tension on FISF measurement results. The effects of surface tension were found to be small but not necessarily negligible in some cases.

Celic, Alan↗
NASA NTRS1998

Phase Inversion: Inferring Solar Subphotospheric Flow and Other Asphericity from the Distortion of Acoustic Waves

A method is proposed for analyzing an almost monochromatic train of waves propagating in a single direction in an inhomogeneous medium that is not otherwise changing in time. An effective phase is defined in terms of the Hilbert transform of the wave function, which is related, via the JWKB approximation, to the spatial variation of the background state against which the wave is propagating. The contaminating effect of interference between the truly monochromatic components of the train is eliminated using its propagation properties. Measurement errors, provided they are uncorrelated, are manifest as rapidly varying noise; although that noise can dominate the raw phase-processed signal, it can largely be removed by low-pass filtering. The intended purpose of the analysis is to determine the distortion of solar oscillations induced by horizontal structural variation and material flow. It should be possible to apply the method directly to sectoral modes. The horizontal phase distortion provides a measure of longitudinally averaged properties of the Sun in the vicinity of the equator, averaged also in radius down to the depth to which the modes penetrate. By combining such averages from different modes, the two-dimensional variation can be inferred by standard inversion techniques. After taking due account of horizontal refraction, it should be possible to apply the technique also to locally sectoral modes that propagate obliquely to the equator and thereby build a network of lateral averages at each radius, from which the full three-dimensional structure of the Sun can, in principle, be determined as an inverse Radon transform.

Gough, Douglas↗
NASA NTRS1975

Haze and sun angle effects on automatic classification of satellite data-simulation and correction

Variations in sun angle and haze level change the spectral signatures collected by multispectral scanners (MSS). This paper describes methods and computer programs that have been developed to simulate the effect of such variations and to correct for them. A basic program, Prediction of the Response of Earth Pointed Sensors (PREPS), is used to calculate the response of the sensor as a function of solar angle, atmospheric haze level, and target reflectance. It is then simply a matter of interpolating these results to simulate changes in haze level or solar angle. In principle, this can be done for any sensor, although at the present time it has been completed for only one - the ERTS-1 MSS.

Potter, J. F.↗
NASA NTRS1980

An equivalent source model of the satellite-altitude magnetic anomaly field over Australia

The low-amplitude, long-wavelength magnetic anomaly field measured between 400 and 700 km elevation over Australia by the POGO satellites is modeled by means of the equivalent source technique. Magnetic dipole moments are computed for a latitude-longitude array of dipole sources on the earth's surface such that the dipoles collectively give rise to a field which makes a least squares best fit to that observed. The distribution of magnetic moments is converted to a model of apparent magnetization contrast in a layer of constant (40 km) thickness, which contains information equivalent to the lateral variation in the vertical integral of magnetization down to the Curie isotherm and can be transformed to a model of variable thickness magnetization. It is noted that the closest equivalent source spacing giving a stable solution is about 2.5 deg, corresponding to about half the mean data elevation, and that the magnetization distribution correlates well with some of the principle tectonic elements of Australia.

Mayhew, M. A.↗
NASA NTRS1991

Reliability analysis of continuous fiber composite laminates

This paper describes two methods, the maximum distortion energy (MDE) and the principle of independent action (PIA), developed for the analysis of the reliability of a single continuous composite lamina. It is shown that, for the typical laminated plate structure, the individual lamina reliabilities can be combined in order to produce the upper and the lower bounds of reliability for the laminate, similar in nature to the bounds on properties produced from variational elastic methods. These limits were derived for both the interactive and the model failure considerations. Analytical expressions were also derived for the sensitivity of the reliability limits with respect to changes in the Weibull parameters and in loading conditions.

Thomas, David J.↗
NASA NTRS1988

Transfinite element methodology for nonlinear/linear transient thermal modelling/analysis - Progress and recent advances

The 'transfinite element method' (TFEM) proposed by Tamma and Railkar (1987 and 1988) for the analysis of linear and nonlinear heat-transfer problems is described and demonstrated. The TFEM combines classical Galerkin and transform approaches with state-of-the-art FEMs to obtain a flexible hybrid modeling scheme. The fundamental principles of the TFEM and the derivation of the governing equations are reviewed, and numerical results for sample problems are presented in extensive graphs and briefly characterized. Problems analyzed include a square plate with a hole, a rectangular plate with natural and essential boundary conditions and varying thermal conductivity, the Space Shuttle thermal protection system, a bimaterial plate subjected to step temperature variations, and solidification in a semiinfinite liquid slab.

Tamma, Kumar K.↗