Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “value stacking”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Stacking order dependence of inverse spin Hall effect and anomalous Hall effect in spin pumping experiments

The dependence of the measured DC voltage on the non-magnetic material (NM) in NM/CoFeB and CoFeB/NM bilayers is studied under ferromagnetic resonance conditions in a TE{sub 011} resonant cavity. The directional change of the inverse spin Hall effect (ISHE) voltage V{sub ISHE} for the stacking order of the bilayer can separate the pure V{sub ISHE} and the anomalous Hall effect (AHE) voltage V{sub AHE} utilizing the method of addition and subtraction. The Ta and Ti NMs show a broad deviation of the spin Hall angle θ{sub ISH}, which originates from the AHE in accordance with the high resistivity of NMs. However, the Pt and Pd NMs show that the kinds of NMs with low resistivity are consistent with the previously reported θ{sub ISH} values. Therefore, the characteristics that NM should simultaneously satisfy to obtain a reasonable V{sub ISHE} value in bilayer systems are large θ{sub ISH} and low resistivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Application of machine learning techniques for fast MeV x-ray spectra unfolding from filter stack spectrometer data

Recovery of MeV x-ray spectra from detector signals is difficult because the response matrix inversion is ill-conditioned and current methods are too slow for high-repetition-rate experiments. In this work, we make use of neural networks to unfold MeV x-ray spectra from measurements obtained with a filter stack spectrometer at rates of near 40 Hz. The neural network was trained on synthetic data and tested on both synthetic and experimental data, the latter obtained in two separate experiments performed at the Omega EP laser facility. We show here that this unfolding method has good performance on synthetic data and that it is a promising option for experimental data of up to 40 MeV. The accuracy on experimental data is verified by using a simple forward model to compare against measured values.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Development of High Average Power Lasers for the Photon Collider

The laser and optics system for the photon collider seeks to minimize the required laser power by using an optical stacking cavity to recirculate the laser light. An enhancement of between 300 to 400 is desired. In order to achieve this the laser pulses which drive the cavity must precisely match the phase of the pulse circulating within the cavity. We report on simulations of the performance of a stacking cavity to various variations of the drive laser in order to specify the required tolerances of the laser system. We look at the behavior of a simple four mirror cavity as shown in Fig. 1. As a unit input pulse is applied to the coupling mirror a pulse begins to build up in the interior of the cavity. If the drive pulses and the interior pulse arrive at the coupling mirror in phase the interior pulse will build up to a larger value. The achievable enhancement is a strong function of the reflectivity of the cavities. The best performance if attained when the reflectivities of the input coupler is matched to the internal reflectivities of the cavity. In Fig. 2 we show the build up of the internal pulse after a certain number of drive pulses, assuming the input coupler has a reflectivity of 0.996 and the interior mirrors have 0.998 reflectivity. With these parameters the cavity will reach an enhancement factor of 450. Reducing the coupler reflectivity gives a faster cavity loading rate but with a reduced enhancement of the internal pulse. The enhancement as a function of coupler reflectivity and total internal cavity reflectivity is shown in Fig. 3. The best enhancement is achieved when the coupling mirror is matched to the reflectivity of the cavity. A coupler reflectivity just below the internal cavity reflectivity minimizes the required laser power.

42 ENGINEERING↗

Band alignment of atomic layer deposited (HfZrO{sub 4}){sub 1−x}(SiO{sub 2}){sub x} gate dielectrics on Si (100)

The band alignment of atomic layer deposited (HfZrO{sub 4}){sub 1−x}(SiO{sub 2}){sub x} (x = 0, 0.10, 0.15, and 0.20) gate dielectric thin films grown on Si (100) was obtained by using X-ray photoelectron spectroscopy and reflection electron energy loss spectroscopy. The band gap, valence band offset, and conduction band offset values for HfZrO{sub 4} silicate increased from 5.4 eV to 5.8 eV, from 2.5 eV to 2.75 eV, and from 1.78 eV to 1.93 eV, respectively, as the mole fraction (x) of SiO{sub 2} increased from 0.1 to 0.2. This increase in the conduction band and valence band offsets, as a function of increasing SiO{sub 2} mole fraction, decreased the gate leakage current density. As a result, HfZrO{sub 4} silicate thin films were found to be better for advanced gate stack applications because they had adequate band gaps to ensure sufficient conduction band offsets and valence band offsets to Si.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Fractional polarization of extragalactic sources in the 500 deg 2 SPTpol survey

In this work, we study the polarization properties of extragalactic sources at 95 and 150 GHz in the SPTpol 500 deg 2 survey. We estimate the polarized power by stacking maps at known source positions, and correct for noise bias by subtracting the mean polarized power at random positions in the maps. We show that the method is unbiased using a set of simulated maps with similar noise properties to the real SPTpol maps. We find a flux-weighted mean-squared polarization fraction $\langle$p 2 $\rangle$ = [8.9 ± 1.1] × 10 -4 at 95 GHz and [6.9 ± 1.1] × 10 -4 at 150 GHz for the full sample. This is consistent with the values obtained for a subsample of active galactic nuclei. For dusty sources, we find 95 percent upper limits of $\langle$p 2 $\rangle$ 95 < 16.9 × 10 -3 and $\langle$p 2 $\rangle$ 150 < 2.6 × 10 -3 . We find no evidence that the polarization fraction depends on the source flux or observing frequency. The 1σ upper limit on measured mean-squared polarization fraction at 150 GHz implies that extragalactic foregrounds will be subdominant to the CMB E and B mode polarization power spectra out to at least ℓ ≲ 5700 (ℓ ≲ 4700) and ℓ ≲ 5300 (ℓ ≲ 3600), respectively, at 95 (150) GHz.

79 ASTRONOMY AND ASTROPHYSICS↗

The ALMA spectroscopic survey in the Hubble Ultra Deep Field: continuum number counts, resolved 1.2 mm extragalactic background, and properties of the faintest dusty star-forming galaxies

We present an analysis of a deep (1σ = 13 μJy) cosmological 1.2 mm continuum map based on ASPECS, the ALMA Spectroscopic Survey in the Hubble Ultra Deep Field. In the 1 arcmin{sup 2} covered by ASPECS we detect nine sources at >3.5σ significance at 1.2 mm. Our ALMA-selected sample has a median redshift of z=1.6±0.4, with only one galaxy detected at z > 2 within the survey area. This value is significantly lower than that found in millimeter samples selected at a higher flux density cutoff and similar frequencies. Most galaxies have specific star formation rates (SFRs) similar to that of main-sequence galaxies at the same epoch, and we find median values of stellar mass and SFRs of 4.0×10{sup 10} M{sub ⊙} and ∼40 M{sub ⊙} yr{sup −1}, respectively. Using the dust emission as a tracer for the interstellar medium (ISM) mass, we derive depletion times that are typically longer than 300 Myr, and we find molecular gas fractions ranging from ∼0.1 to 1.0. As noted by previous studies, these values are lower than those using CO-based ISM estimates by a factor of ∼2. The 1 mm number counts (corrected for fidelity and completeness) are in agreement with previous studies that were typically restricted to brighter sources. With our individual detections only, we recover 55% ± 4% of the extragalactic background light (EBL) at 1.2 mm measured by the Planck satellite, and we recover 80% ± 7% of this EBL if we include the bright end of the number counts and additional detections from stacking. The stacked contribution is dominated by galaxies at z∼1--2, with stellar masses of (1–3) × 10{sup 10} M {sub ⊙}. For the first time, we are able to characterize the population of galaxies that dominate the EBL at 1.2 mm.

79 ASTRONOMY AND ASTROPHYSICS↗

Low-field-actuated giant magnetocaloric effect and excellent mechanical properties in a NiMn-based multiferroic alloy

Multiferroic magnetic shape memory alloys with first-order magntostructural transformation exhibit much enhanced magnetocaloric effect which incorporates the latent heat associated with the phase transformation itself, but they suffer from the drawbacks of large hysteresis and transformation interval and consequently too high critical field to actuate the magnetocaloric effect, greatly impeding their applications. Here, by generating a kind of specific stacking-mediated structure of martensite through minor Al substitution to improve the geometric compatibility between martensite and austenite in the Ni 40 Co 10 Mn 40 Sn 9 Al 1 alloy, we greatly reduced the thermal hysteresis and transformation temperature interval while conserving the large magnetization difference between the two phases. Consequently, a low-field-actuated giant magnetocaloric effect with isothermal entropy change of 23 J kg –1 K –1 for a field change from 0 to 2 T, which is among the highest values reported heretofore for all magnetocaloric materials, was successfully achieved. Meanwhile, with minor Al substitution, the present single-phase multiferroic alloy that is intermetallic in nature exhibits superior mechanical properties, including excellent compressive properties over a wide temperature range and a relatively high fracture toughness, which are quite beneficial for practical applications. Lastly, by incorporating the advantages of low cost, environment friendliness and easy fabrication, this alloy shows great potential for magnetocaloric applications.

36 MATERIALS SCIENCE↗

Enhanced strength and toughness in ultra-fine grained 99.9% copper obtained by cryo-hydrostatic extrusion

Highlights: • Cryo-HE can increase the yield strength of Cu by more than threefold. • In cryo-HE of Cu, the grain refinement is stronger by 30% than in room-HE. • Cryo-HE with post-annealing effectively creates a bimodal microstructure in Cu. • Short-term post-annealing applied to cryo-HE-treated Cu can double its ductility. • Grain refinement with recrystallization results in a slight increase of Cu toughness. - Abstract: Ultrafine grained 99.9% Cu with enhanced strength and toughness was produced by hydrostatic extrusion conducted at the temperature of liquid nitrogen. The cryo-extruded Cu has a tensile yield strength of 490 MPa, hardness of 145 HV0.2, and tensile fracture toughness of 39.5 MPa m{sup 1/2}, which means that their values increased by 380%, 185% and ~10%, respectively, compared to those of the starting material. The significant strengthening is due to the strong grain refinement to 320 nm and the high energy of defects stored during the processing at liquid nitrogen temperature. The short term post deformation annealing doubles the ductility of material even by above 10% of the elongation to fracture at a slight expense of the yield strength (485 MPa). The observed behavior of Cu can be explained in terms of its low stacking fault energy, the susceptibility to dynamic recrystallization within the working zone of the extrusion die, and the triaxial strain components with the very large strain gradients, combined with the significant adiabatic heating effect active during the hydrostatic extrusion. The better homogeneity of the grain refinement and the higher efficiency of the distribution of defects and of the energy storage accompanied by the decreased dislocation mobility during the cryo hydrostatic extrusion contributed to the higher strength.

36 MATERIALS SCIENCE↗

Methods For Calculating Thyroid Doses to The Residents Of Ozersk Due to 131I Releases From The Stacks of The Mayak Production Association

The Mayak Production Association (MPA) was established in the late 1940s in accordance with a special Decree of the USSR Government for the production of nuclear weapons. In early years of MPA operation, due to the lack of experience and absence of effective methods of RW management, the enterprise had extensive routine (designed) and non-routine (accidental) releases of gaseous radioactive wastes to the atmosphere. These practices resulted in additional technogenic radiation exposure of residents inhabiting populated areas near the MPA. The primary objective of ongoing studies under JCCRER Project 1.4 is to estimate doses to the residents of Ozersk due to releases of radioactive substances from the stacks of MPA. Preliminary scoping studies have demonstrated that releases of radioactive iodine (131I) from the stacks of the Mayak Radiochemical Plant represented the major contribution to the dose to residents of Ozersk and of other nearby populated areas. The behavior of 131I in the environment and of 131I migration through biological food chains (vegetation-cows-milk-humans) indicated a need for use of special mathematical models to perform the estimation of radiation doses to the population. The goal of this work is to select an appropriate model of the iodine migration in biological food chains and to justify numerical values of the model parameters.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Influence of Mn addition on the microstructure and mechanical properties of a directionally solidified γ-TiAl alloy

Highlights: • Mn addition can significantly improve the yield strength of TiAl alloy. • Introduction of Mn facilitates the operation of twinning-controlled deformation. • Twin-dislocation interactions cause a continuous increase in work hardening rate. - Abstract: TiAl alloys with nominal compositions of Ti-47Al-2Nb-2Cr-(0, 1, 3, 5)Mn were prepared via electromagnetic cold crucible directional solidification (ECCDS), and the influence of Mn addition on the microstructure and mechanical properties of the alloys was investigated. The experimental results showed that the Mn atoms were dissolved within the TiAl alloy, and no Mn compounds were formed. Based on the X-ray diffraction (XRD) analysis results, the peak angle of the Mn-containing sample shifted to a higher value, indicating lattice shrinkage. The Mn addition also increased the volume fraction of the B2 phase. The yield strength of the TiAl alloy monotonically increased as the content of the substitutional-solute Mn atoms increased. The ultimate strengths of the TiAl alloys containing 1 at.%, 3 at.%, and 5 at.% Mn consequently decreased because micro-cracks were preferentially formed in the B2 phase during room-temperature deformation. The introduction of substitutional-solute Mn atoms could result in a reduction of the stacking-fault energy of the γ phase, and facilitate the operation of twinning-controlled plastic-deformation during the intermediate stage of the plastic deformation process. The interaction between the deformation twins and movable dislocations led to a continuous increase in the work-hardening rate.

36 MATERIALS SCIENCE↗

Effect of Natural Fermentation of Sorghum on Resistant Starch Molecular Structure and Fermentation Property

Relevant research results have suggested that fermentation can increase the content of sorghum amylose chains and their retrogradation value. Therefore, this study explored the effect of fermentation pretreatment on the yield, digestibility, molecular structure, and in vitro fermentation property of sorghum-resistant starch by conducting fermentation pretreatment of sorghum and extracting the resistant starch from fermented sorghum with pressure-heat compound enzyme method. The results were as follows. After fermentation pretreatment, the yield of sorghum-resistant starch increased, the digestibility of sorghum-resistant starch reduced, the laminated structure size on the surface of the particles became more uniform, and the stacking mode became more neat and denser. The sorghum-resistant starch prepared before and after fermentation did not produce new chemical groups, and its functional group peak remained unchanged. After fermentation, the weight-average molecular weight of sorghum-resistant starch was elevated, and the percentage content of high- and low-molecular substances increased and decreased, respectively, compared with that of the unfermented sorghum-resistant starch. The percentage content of short-chain branches in the branched chain increased, whereas that of the long-chain branches decreased; the crystallinity of sorghum-resistant starch after fermentation decreased, and the intensity of X-diffraction peak changed slightly before and after fermentation. According to the results of the in vitro fermentation experiments, the fermentation broth of sorghum-resistant starch had the highest content of butyric acid and short-chain fatty acid. Research results reveal that, after fermentation pretreatment, sorghum-resistant starch presented increased yield, more complex molecular structure, heavier molecular weight and more uniform surface morphology, more efficient butyric acid generation, and greater fermentation rate than unfermented sorghum-resistant starch.

Ge, YunFei↗

Early Beam Injection Scheme for the Fermilab Booster: A Path for Intensity Upgrade

Over the past decade, Fermilab has focused efforts on the intensity frontier physics and is committed to increase the average beam power delivered to the neutrino and muon programs substantially. Many upgrades to the existing injector accelerators, namely, the current 400 MeV LINAC and the Booster, are in progress under the Proton Improvement Plan (PIP). Proton Improvement Plan-II (PIP-II) proposes to replace the existing 400 MeV LINAC by a new 800 MeV LINAC, as an injector to the Booster which will increase Booster output power by nearly a factor of two from the PIP design value by the end of its completion. In any case, the Fermilab Booster is going to play a very significant role for nearly next two decades. In this context, I have developed and investigated a new beam injection scheme called "early injection scheme" (EIS) for the Booster with the goal to significantly increase the beam intensity output from the Booster thereby increasing the beam power to the HEP experiments even before PIP-II era. The scheme, if implemented, will also help improve the slip-stacking efficiency in the MI/RR. Here I present results from recent simulations, beam studies, current status and future plans for the new scheme.

43 PARTICLE ACCELERATORS↗

First STAX detector installation at the National Institute for Radioelements (IRE)

The Source Term Analysis of Xenon (STAX) project has been installing stack detectors at medical isotope production facilities to measure radioxenon emissions to investigate the effect of radioxenon releases on nuclear explosion monitoring. This paper outlines the installation of the first STAX detection system at the National Institute for Radioelements (IRE) in Fleurus, Belgium which has been operating for over three years and transferring collected data to the STAX repository. Information about the equipment installed, the data flow established, and calculations for determination of radioxenon releases from the facility are presented. Further. data quality was investigated to confirm values reported by STAX automated data processing and in a comparison of collected STAX data with data collected by IRE for regulatory reporting.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Amorphous/crystalline silicon interface passivation: Ambient-temperature dependence and implications for solar cell performance

Silicon heterojunction (SHJ) solar cells feature amorphous silicon passivation films, which enable very high voltages. We report how such passivation increases with operating temperature for amorphous silicon stacks involving doped layers and decreases for intrinsic-layer-only passivation. We discuss the implications of this phenomenon on the solar cell's temperature coefficient, which represents an important figure-of-merit for the energy yield of devices deployed in the field. We show evidence that both open-circuit voltage (Voc) and fill factor (FF) are affected by these variations in passivation and quantify these temperature-mediated effects, compared with those expected from standard diode equations. We confirm that devices with high Voc values at 25°C show better high-temperature performance. Thus, we also argue that the precise device architecture, such as the presence of charge-transport barriers, may affect the temperature-dependent device performance as well.

14 SOLAR ENERGY↗

SYNGAS PRODUCTION VIA HIGH-TEMPERATURE COELECTROLYSIS OF STEAM AND CARBON DIOXIDE

This paper presents results of recent experiments on simultaneous high-temperature electrolysis (coelectrolysis) of steam and carbon dioxide using solid-oxide electrolysis cells. Coelectrolysis is complicated by the fact that the reverse shift reaction occurs concurrently with the electrolytic reduction reactions. All reactions must be properly accounted for when evaluating results. Electrochemical performance of the button cells and stacks were evaluated over a range of temperatures, compositions, and flow rates. The apparatus used for these tests is heavily instrumented, with precision mass-flow controllers, on-line dewpoint and CO2 sensors, and numerous pressure and temperature measurement stations. It also includes a gas chromatograph for analyzing outlet gas compositions. Comparisons of measured compositions to predictions obtained from a chemical equilibrium coelectrolysis model are presented, along with corresponding polarization curves. Results indicate excellent agreement between predicted and measured outlet compositions. Cell area-specific resistance values were found to be similar for steam electrolysis and coelectrolysis. Coelectrolysis significantly increases the yield of syngas over the reverse water gas shift reaction equilibrium composition. The process appears to be a promising technique for large-scale syngas production.

10 SYNTHETIC FUELS↗

Estimating Air Chemical Emissions from Research Activities Using Stack Measurement Data

Current methods of estimating air emissions from research and development (R&D) activities use a wide range of release fractions or emission factors with bases ranging from empirical to semi-empirical. Although considered conservative, the uncertainties and confidence levels of the existing methods have not been reported. Chemical emissions were estimated from sampling data taken from four research facilities over ten years. The approach was to use a Monte Carlo technique to create distributions of annual emission estimates for target compounds detected in source test samples. Distributions were created for each year and building sampled for compounds with sufficient detection frequency to qualify for the analysis. The results using the Monte Carlo technique without applying a filter to remove negative emission values showed almost all distributions spanning zero, and forty percent of the distributions having a negative mean. This indicates that emissions are so low as to be indistinguishable from building background. Application of a filter to allow only positive values in the distribution provided a more realistic value for emissions and increased the distribution mean by an average of sixteen percent. Release fractions were calculated by dividing the emission estimates by a building chemical inventory quantity. Two variations were used for this quantity: chemical usage, and chemical usage plus one-half standing inventory. Filters were applied so that only release fraction values from zero to one were included in the resulting distributions. Release fractions had a wide range among chemicals and among data sets for different buildings and/or years for a given chemical. Regressions of release fractions to molecular weight and vapor pressure showed weak correlations. Similarly, regressions of mean emissions to chemical usage, chemical inventory, molecular weight and vapor pressure also gave weak correlations. These results highlight the difficulties in estimating emissions from R&D facilities using chemical inventory data.

air chemical sampling, air emissions, research and↗

A close comparison between observed and modeled Lyα lines for z ∼ 2.2 Lyα emitters

We present the results of an Lyα profile analysis of 12 Lyα emitters (LAEs) at z∼2.2 with high-resolution Lyα spectra. We find that all 12 objects have an Lyα profile with the main peak redward of the systemic redshift defined by nebular lines, and five have a weak, secondary peak blueward of the systemic redshift (blue bump). The average velocity offset of the red main peak (the blue bump, if any) with respect to the systemic redshift is Δv{sub Lyα,r}=174±19 km s{sup −1} (Δv{sub Lyα,b}=−316±45 km s{sup −1}), which is smaller than (comparable to) that of Lyman break galaxies (LBGs). The outflow velocities inferred from metal absorption lines in three individual and one stacked spectra are comparable to those of LBGs. The uniform expanding shell model constructed by Verhamme et al. reproduces not only the Lyα profiles but also other observed quantities, including the outflow velocity and the FWHM of nebular lines for the non-blue-bump objects. On the other hand, the model predicts too high FWHMs of nebular lines for the blue bump objects, although this discrepancy may disappear if we introduce additional Lyα photons produced by gravitational cooling. We show that the small Δv{sub Lyα,r} values of our sample can be explained by low neutral hydrogen column densities of log(N{sub H I}) = 18.9 cm{sup −2} on average. This value is more than one order of magnitude lower than those of LBGs but is consistent with recent findings that LAEs have high ionization parameters and low H i gas masses. This result suggests that low N{sub H I} values, giving reduced numbers of resonant scattering of Lyα photons, are the key to the strong Lyα emission of LAEs.

79 ASTRONOMY AND ASTROPHYSICS↗

Phase Field Dislocation Dynamics (PFDD) version 2.x

This disclosure is for version 2.x of a mesoscale model called Phase Field Dislocation Dynamics (PFDD). PFDD is used for investigating deformation in nanoscale (grain sizes of ~300 nm and less) materials, such as metals and alloys. This approach models the motion and interaction of individual defects, namely dislocations, in the material using scalar-valued phase field variables, also called order parameters. The system is evolved through energy minimization thus the model calculates the total energy density in terms of the phase field variables. The energy minimization is completed using the Ginzburg-Landau equation, and is implemented with explicit time integration. The total system energy can be comprised of several terms, including the strain energy (which describes dislocation-dislocation interactions), the energy due to an applied stress (dislocation interactions with the applied stress), and a core/lattice (perfect dislocations) or generalized stacking fault (partial dislocations) energy (described the dislocation core structure). The latter term in particular may vary based on the crystal structure being modeled and is typically informed using lower length scale (e.g., atomistic) approaches, although no such (atomistic) calculations are completed within the PFDD algorithm. This basic formulation was previously reviewed by Los Alamos National Laboratory and released under license number C17113. This previously reviewed version we will henceforth refer to as PFDD v1.0. PFDD v1.0 consisted of 2 codes (one parallel and one serial) plus input files, all written in the C language. This new disclosure is addressing the next versions of the PFDD, versions 2.x. There have been several enhancements of PFDD v1.0, which are described here and included in the attached code, which we will refer to as PFDD v2.0. There are also several new features described here that are either planned or already in process and are expected to be subsequent releases, i.e., v2.1, v2.2, ...v2.x.

Hunter, Abigail↗