Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “titanium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Enhanced boron doping for diamond growth in cylindrical CVD reactors using a Faraday cage

We report on the use of 3D-printed titanium Faraday cages in a cylindrical resonant cavity CVD reactor for the growth of heavily boron-doped single-crystalline superconducting diamond. We show that the cage enhances boron doping uniformity and provides control of the doping efficiency and growth rate by varying the distance between the plasma and the diamond surface. Using finite element modelling, we demonstrate that the Faraday cage focuses the electric field at the top of the cage whilst also suppressing the electric field inside the cage, thereby pinning the plasma at a fixed height above the sample. This eliminates plasma “hot spots” at the edges of the sample and creates a more uniform plasma electron and hydrogen radical distribution over the sample, resulting in a more uniform boron incorporation.

Boron doped diamond↗
DOE OSTI2021

Evaluation of electrochemical performance and redox activity of Fe in Ti doped layered P2-Na0.67Mn0.5Fe0.5O2 cathode for sodium ion batteries

Here, we report a wet synthesis-based titanium doping strategy to improve the structural stability and electrochemical performances, such as cycling stability and rate capability, of P2-type Na 0.67 Fe 0.5 Mn 0.5 O 2 layered oxide cathodes. Through Ti 4+ doping aimed at replacing some of the Mn and Fe atoms in the crystal structure, effective mitigation of the Jahn Teller distortion caused by active Mn 3+ before charging and Fe 4+ after charging was achieved. X-ray diffraction (XRD), Raman spectroscopy, Electrochemical Impedance Spectroscopy (EIS) and Mössbauer spectroscopy were used to investigate the effects of the Ti 4+ dopant before and after cycling. It was observed that Ti 4+ doping increased the Na layer thickness, minimized the lattice volume strain, showed better structural stability, minimally decreased Fe migration to the Na layer, and lowered charge transfer resistance in these P2-type cathodes. Overall, our reported synthesis methodology and electrochemical characterizations highlight the feasibility of Ti doping in sodium layered oxide P2-type cathodes.

25 ENERGY STORAGE↗
DOE OSTI2020

A new hydrous iron oxide phase stable at mid-mantle pressures

The amount of hydrogen stored in the Earth's interior is important for a range of issues, including the volatile incorporation during the Earth formation and the co-evolution of the atmosphere, the hydrosphere, and the interior. Recent experiments found titanium bearing ε-FeOOH in a hydrous basaltic system at 12–19 GPa and 1300 K. Pyrite-type FeOOH was found to be stable at pressures higher than 80 GPa. These discoveries suggest possible hydrogen storage in the mantle transition zone and in the mantle below 1800 km depths, respectively. However, it remains uncertain how the potential deep hydrogen storage can be connected to the shallower storage. Here, we report a new hydrous iron oxide (η-Fe 12 O 18+x / 2 H x , x ≈ 2) stable at pressures between the stability fields of the ε- and the pyrite-type FeOOH. Our experiment also shows that the new η phase can exist together with the major lower mantle minerals including bridgmanite and periclase, making it an important hydrogen-bearing phase in the Earth's deep interior. Because of its limited H 2 O storage capacity, which is less than 1/6 of the storage capacity of the pyrite-type phase and the ε phase, the stability of the η phase would result in H 2 O loss during water transport in the mid mantle and therefore limit the amount of H 2 O potentially stored in the Fe–O–H system of the lower mantle. As a result, the large channel in the crystal structure of the η phase could provide potential storage sites for other volatile elements in the deep mantle.

58 GEOSCIENCES↗
DOE OSTI2024

Acoustic and electrical properties of Fe-Ti oxides with application to the deep lunar mantle

The overturn of titanium-rich mantle cumulates has been invoked to explain the structure and dynamics of the Moon. These dense cumulates are stable at the core-mantle boundary (CMB) and could explain field observations inferred from geophysical studies. Here, we report acoustic and electrical experiments on natural ilmenite-rutile aggregates up to 4.5 GPa and 1920 K. Seismic velocities show a weak pressure and temperature dependence, with Vs ~ 4.2 (+/-0.2) km/s and Vp ~8.0 (+/-0.2) km/s at the CMB conditions. Conductivity increases by a factor of 10 4 from 373 to 1920 K and is >10(3) S/m above 1573 K. Seismic and electrical models for the lunar mantle based on our results, considering mixtures of Fe-Ti oxides and olivine, indicate that field velocity and conductivity estimates are reproduced satisfactorily with 3-16 vol.% Fe-Ti oxides and 20 vol.% melt. Interactions between a Ti-rich, melt-bearing layer and the adjacent core likely affect the cooling and magnetic history of the Moon.

58 GEOSCIENCES↗
DOE OSTI2025

Accurate and efficient predictions of keyhole dynamics in laser materials processing using machine learning-aided simulations

The keyhole phenomenon has been widely observed in laser materials processing, including laser welding, remelting, cladding, drilling, and additive manufacturing. Keyhole-induced defects, primarily pores, dramatically affect the performance of final products, impeding the broad use of these laser-based technologies. The formation of these pores is typically associated with the dynamic behavior of the keyhole. So far, the accurate characterization and prediction of keyhole features, particularly keyhole depth, as a function of time, has been a challenging task. In situ characterization of keyhole dynamic behavior using the synchrotron X-ray technique is informative but complicated and expensive. Current simulations are generally hindered by their poor accuracy and generalization abilities in predicting keyhole depths due to the lack of accurate laser absorptance data. In this study, we develop a machine learning-aided simulation method that accurately predicts keyhole dynamics, especially in keyhole depth fluctuations, over a wide range of processing parameters. In two case studies involving titanium and aluminum alloys, we achieve keyhole depth prediction with a mean absolute percentage error of 10 %, surpassing those simulated using the ray-tracing method with an error margin of 30 %, while also reducing computational time. This exceptional fidelity and efficiency empower our model to serve as a cost-effective alternative to synchrotron experiments. Our machine learning-aided simulation method is affordable and readily deployable for a large variety of materials, opening new doors to eliminate or reduce defects for a wide range of laser materials processing techniques.

Computational fluid dynamics↗
DOE OSTI2024

Surface exsolving perovskite ceramics as catalyst for microwave methane pyrolysis to co-generate hydrogen and carbon nanotube

In this study, we have successfully developed a novel surface exsolving perovskite ceramic, which demonstrates the ability to simultaneously generate CO x -free hydrogen and carbon nanotubes (CNTs) through methane pyrolysis under the influence of microwave irradiation. We conducted an extensive survey and optimization of various perovskite materials specifically tailored for microwave applications. Among the materials investigated, nickel-doped strontium titanium oxide (STON) emerged as the most promising candidate, exhibiting both a satisfactory methane conversion rate and excellent responsiveness to microwave irradiation. Refinement of STON was carried out by fine-tuning the Ni content, optimizing the reduction dwell time, and adjusting the reduction temperature. Notably, SrTiNi 0.08 O 3 (STON8), demonstrated an impressive initial methane conversion rate of up to 40%. Transmission Electron Microscopy (TEM) provided visual evidence of the correlation between Ni content and reduction temperature, with respect to the exsolved Ni metal particle size. This finding highlights the immense potential of surface exsolving perovskite ceramics as a highly effective catalyst for the simultaneous production of CNTs and COx-free hydrogen via methane pyrolysis under microwave irradiation. Furthermore, it represents a step forward in the field of catalytic materials and microwave-driven processes.

08 HYDROGEN↗
DOE OSTI2026

High-Throughput Uniformity and Defect Monitoring in Low-Temperature Electrolysis Porous Transport Layers Using X-Ray Radiography

Effective quality control (QC) for manufacturing proton exchange membrane water electrolysis (PEMWE) components is critical to enabling widespread adoption of the technology for hydrogen generation. This study investigates X-ray radiography as a novel, high-throughput, potentially in-line QC technique for detecting defects and assessing material property distributions in titanium-based porous transport layers (PTLs) which constitute a crucial component of low temperature PEMWE stacks. We obtain radiographs of a set of fifteen PTLs and model their absorbance of the broadband radiation as a second-order polynomial to account for the non-monoenergetic radiation source used in this study. The resulting model serves as a basis for predicting the areal density and porosity distributions of the PTLs. We find radiography successful in detecting multiple instances of defects, including holes/depressions, cracks, and excess material on the surface or in the pores of the material, demonstrating its potential as a robust in-line QC tool for PTL manufacturing.

08 HYDROGEN↗
DOE OSTI2025

Investigation of residual stress distribution in wire-arc directed energy deposited refractory molybdenum alloy utilizing numerical thermo-mechanical analysis and neutron diffraction method

Directed energy deposition (DED), a metal additive manufacturing (AM) technique, offers higher deposition rates and energy efficiency, making it suitable for fabricating components from refractory molybdenum alloys, such as molybdenum-titanium-zirconium (TZM). However, large thermal gradients and non-equilibrium thermal cycles in DED could generate high residual stress in the component, potentially deteriorating quality and performance. Thus, this study aims to investigate residual stress generation and its distribution in wire-arc DED of TZM thin-wall, utilizing thermo-mechanical analysis and high-fidelity neutron diffraction (ND) method. Two interpass temperatures (50°C and 200°C) have been considered to investigate their impact on residual stress formation. During experiments, in-situ thermal data has been recorded using thermocouples, which have been utilized for calibrating the thermal model. Thermocouple data shows a good agreement with the simulation results, having a difference of less than 10 %. Post-deposition part deformation has been observed, which is measured using a coordinate measuring machine, showing maximum values of 0.93 mm and 0.78 mm for interpass temperatures of 50°C and 200°C, respectively. Numerical predictions of distortion deviated by less than 15% from the experimental results. ND measurement and simulation results indicate that residual stress magnitude and evolution vary across the TZM deposits, revealing microstructural anisotropy in both conditions. Notably, lower interpass temperatures resulted in higher residual stresses, confirmed by experimental and simulation data. Further, this study demonstrated that an integrated experimental and thermo-mechanical analysis can potentially reveal the temperature history, part deformation, and residual stress formation in wire-arc DED TZM alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2026

High-throughput oxidation screening and down-selection of refractory high entropy alloys in the Al-Cr-Mo-Nb-Ta-Ti system

Rapid experimentation and characterization are ever-present needs in the discovery of high entropy alloys. High entropy alloy systems are difficult to survey with systematic composition sweeps using traditional synthesis methods. The number of distinct compositions in even a four-element system is experimentally intractable. Exploration of these, and higher-element systems, necessitates thermodynamic prediction coupled with an automated sample creation method and a rapid screening methodology to effectively down-select alloys with targeted properties. As a result, a high-throughput method for evaluating the oxidation performance of refractory high entropy alloys was developed and tested. The six-element system of aluminum, chromium, molybdenum, niobium, tantalum, and titanium was evaluated for single phase stability and short-duration oxidation resistance. Target compositions were initially determined via thermodynamic predictions of single-phase stability across a wide temperature range. A twenty-five-sample build plate was produced using directed energy deposition additive manufacturing. After fabrication, the twenty-five 1 cm 3 samples were heat treated and characterized for composition and phase identification. The build plate was exposed to a high temperature oxidizing environment at 1000 °C for three hours. After oxidation, the composition, morphology, and chemistry of the oxides formed were characterized. Of the twenty-five samples produced, nine exhibited a favorable oxidation response, from which a single-phase BCC alloy at a composition of Al 13 Cr 7 Mo 19 Nb 18 Ta 26 Ti 17 was identified as the alloy with the most protective oxidation coating with a thin, adherent oxide scale. Finally, the complete experimental down-selection—from machine setup to final alloy identification—required approximately 45 labor hours, demonstrating a rapid validation for alloy discovery.

Additive manufacturing↗
DOE OSTI2023

Re-investigation of high-temperature phase equilibria in Fe-rich Sm–Fe–Ti alloys

Recently renewed attempts to develop high-performance rare-earth-lean permanent magnets based on the Sm(Fe,Ti) 12 compound have drawn attention to the limited knowledge about the high-temperature phase equilibria in the Sm–Fe–Ti system. Experimental investigation of equilibrated alloys with electron probe microanalysis, X-ray diffraction and thermomagnetic analysis revealed several inaccuracies in the currently accepted phase relations at 1000°C and allowed for a revision of the Fe-rich corner of the Sm–Fe–Ti phase diagram. The Sm(Fe,Ti) 12 and Sm 3 (Fe,Ti) 29 phases were found to have more extended Ti ranges of 5.1–9.7 at% and 2.8–6.9 at%, respectively. With increasing of the Ti content, the Curie temperature of the Sm(Fe,Ti) 12 remains nearly constant at 306–312°C, whereas that of the Sm 3 (Fe,Ti) 29 increases from 188°C to 207°C. The low-titanium Sm 3 (Fe,Ti) 29 phase equilibrates not only with the Sm(Fe,Ti) 12 and Sm2(Fe,Ti) 17 phases, but also with (α-Fe) solid solution. Newly demonstrated equilibrium between Sm 2 (Fe,Ti) 17 and TiFe 2 phases makes impossible the earlier reported equilibrium between the Sm 3 (Fe,Ti) 29 and Sm(Fe,Ti) 11 phases. Because of an invariant reaction at 1000 °C, the revised phase diagram also features a class II four-phase equilibrium Sm 3 (Fe,Ti) 29 + TiFe 2 + Sm(Fe,Ti) 12 + Sm 2 (Fe,Ti) 17 . Peritectic decomposition of the Sm(Fe,Ti) 11 phase, which occurs either at 1075°C or at 1087°C, was found to have among its products the Sm(Fe,Ti) 12 phase. Although no such equilibration was attempted, it must be possible to obtain above 1087°C a two-phase state composed of the Sm(Fe,Ti) 12 phase and a liquid – which is important for manufacturing of the Sm(Fe,Ti) 12 - based permanent magnets via the liquid-phase sintering.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Insights into Ti doping for stabilizing the Na 2/3 Fe 1/3 Mn 2/3 O 2 cathode in sodium ion battery

Iron- and manganese-based layered metal oxides, as cathodes for sodium ion batteries, have received widespread attention because of the low cost and high specific capacity. However, the Jahn-teller effect of Mn 3+ ions and the resulted unstable structure usually lead to continuously capacity decay. Herein, Titanium (Ti) has been successfully doped into Na 2/3 Fe 1/3 Mn 2/3 O 2 to suppress the Jahn-Teller distortion and improve both cycling and rate performance of sodium ion batteries. In situ high-energy synchrotron X-ray diffraction study shows that Ti-doped compound (Na 2/3 Fe 1/3 Mn 0.57 Ti 0.1 O 2 ) can maintain the single P2 phase without any phase transition during the whole charging/discharging process. Further, various electrochemical characterizations are also applied to explore the better kinetics of sodium ions transfer in the Na 2/3 Fe 1/3 Mn 0.57 Ti 0.1 O 2 . This work provides a comprehensive insight into the Ti-doping effects on the performance from both structural and electrokinetic perspectives.

25 ENERGY STORAGE↗
DOE OSTI2024

Additively manufactured β-Ti5553 with laser powder bed fusion: Microstructures and mechanical properties of bulk and lattice parts

Ti5553 (Ti-5Al-5Mo-5V-3Cr wt%) is a titanium alloy widely used for its high strength-to-weight ratio and good formability at elevated temperatures. Unlike Ti-6Al-4V, Ti5553 does not undergo martensitic transformation, preventing cracking of brittle martensite upon rapid cooling. This makes it a strong candidate for additive manufacturing (AM), particularly laser powder bed fusion (L-PBF). L-PBF offers the unique opportunity to make fine lattice structures to reduce component weight. Despite the growing field of AM, there have been limited studies on L-PBF Ti5553 lattices and how their properties differ from the bulk. Here the present work addresses this knowledge gap by investigating microstructures and properties of L-PBF bulk and lattice parts and the effect of post L-PBF heat treatments. Electron microscopy and mechanical testing show that the high dislocation density formed during L-PBF increases bulk part’s yield strength by approximately 100 MPa compared to the conventional alloy. Digital image correlation during compression testing of octet truss lattices reveals a layer-by-layer failure mode. Compared to the bulk, the lattice contains copious ω nanoprecipitation, weaker <001> texture, smaller average grain sizes, and larger content of high-angle grain boundaries. These features elicit differences in Taylor factor distributions for the lattice depending on load direction, underlining challenges in predicting lattice mechanical response based on bulk properties. By examining the processing-structure-property relationships in the bulk and lattice, the present results delineate their microstructural and mechanical differences and establish a benchmark for the future design applications of L-PBF Ti5553.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electronic structure and magnetism of pristine, defected, and strained $\mathrm{Ti_2N}$ $\mathrm{MX}$ene

Here, from first principles electronic structure calculations, we unravel the evolution of structural, electronic, and magnetic properties of pristine, defected, and strained titanium nitride MXene with different functional groups (-F, -O, -H, and -OH). The formation and cohesive energies reveal their chemical stability. The dynamical stability of Ti 2 N mono-layer is also confirmed by phonon calculations. The MAX phase and defect free functionalized MXenes are metallic except for oxygen terminated (Ti 2 NO 2 ) one which is 100% spin polarized half-metallic ferromagnet. The spin–orbit coupling significantly influences the bare MXene (Ti 2 N) to exhibit Dirac topology and band inversion near the high symmetry directions. The strain effect sways the Fermi level thereby shifting it towards lower energy state under compression and towards higher energy state under tensile strain in Ti 2 NH 2 . The Ti 2 NO 2 exhibits exotic electronic structure not only in pristine but also in strained and defected structures. Its half-metallic nature changes to semi-metallic under 1% compression and it is completely destroyed under 2% compression. In single vacancy defect, its band structure remarkably transforms from half-metallic to semi-conducting with large band gap in 12.5% Ti, weakly semi-conducting in 5.5% Ti, and semi-metallic in 12.5% O. The 25% N defect changes its half-metallic characteristic to metallic. Further, the 12.5% Co substitution preserves its half-metallic character, whereas Mn substitution allows it to convert half-metallic characteristic into weak semi-metallic characteristic preserving ferromagnetism. However, Cr substitution converts half-metallic ferromagnetic state to half-metallic anti-ferromagnetic state. The understanding made here on collective structural stability, and electronic band structure, and magnetic phenomena in novel 2D Ti 2 N derived MXenes open up their possibility in designing them for synthesis.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Modeling Ti–6Al–4V using crystal plasticity, calibrated with multi-scale experiments, to understand the effect of the orientation and morphology of the α and β phases on time dependent cyclic loading

Classically, crystal plasticity modeling has used a range of constitutive equations, in which the incorporation of additional physics-based relationships typically results in additional model parameters. These additional parameters need to be reliably calibrated, which often necessitates the use of a range of experimental data acquired at multiple length scales. In this work, a crystal plasticity based finite element (CPFE) model for a dual-phase Titanium alloy, Ti–6Al–4V, is developed. The α and β phases of the microstructure are explicitly modeled. The model is calibrated using a systematic optimization routine and experimental data that consist of macroscopic stress-strain curves coupled with lattice strains on different crystallographic planes for the two phases. These experimental data were obtained from in situ high energy X-ray diffraction experiments for multiple material pedigrees, with varying crystallographic orientation distribution and β volume fractions. Depending on the thermomechanical-processing route and the heat treatment used to manufacture the alloy, Ti–6Al–4V can exist in a wide number of microstructural forms, which often results in the α and β phases either having well aligned slip systems (following the Burgers orientation relationship (BOR)) or possessing no alignment of the slip systems across the interphase boundary (not following the BOR). In this study, the fully-calibrated CPFE model is used to gain a comprehensive understanding of the deformation behavior of Ti–6Al–4V, specifically, the effect of microstructures that follow the BOR (or not) on time-dependent cyclic loading (including the effects of dwell hold times).

36 MATERIALS SCIENCE↗
DOE OSTI2024

Spherical Indentation and Implementation of S 3 /P for yield stress determination of brittle materials

Here, a mathematically transparent and robust experimental method has been developed to estimate the yield stress of brittle materials through the analysis of depth-sensing spherical indentation. Employing Hertzian contact mechanics, an elastically invariant ratio based on the simple equation S 3 / P = 6RE r 2 , (where S and P are contact stiffness and indentation load, respectively) has been derived that enables more accurate and confident determination of the transition from elastic to inelastic deformation; a transition that the yield stress dictates and represents. Using two diamond spheres with radii of 3.2 and 8.6 μm, the indentation test method and analyses are applied to two vitreous silicates: Corning's HPFS 7980® fused silica and Vitro's Starphire® soda lime silicate. The estimated yield strengths are 8.15 GPa ± 2.5% for the fused silica and 6.1 GPa ± 3.3% for the soda-lime silicate, and both were independent of indenter radius. Verification of this new experimental method is demonstrated with an as-drawn titanium by showing equivalence of measured yield stress by its spherical indentation and that from uniaxial compression testing. This method will enable easier and more confident estimation of yield stress in brittle materials - a property that historically has been elusive to measure for these materials using common laboratory mechanical test methods.

36 MATERIALS SCIENCE↗
DOE OSTI2026

The effect of varying powder feedstock chemistry and printing atmosphere on the microstructure of additively manufactured nickel-based ODS alloys: Role on stabilization of cellular structures vs. oxide dispersion formation

Nickel-based alloys have a wide variety of structural applications due to their high corrosion resistance and mechanical strength which depend on solid solution strengthening, or the formation of oxides and/or intermetallic precipitation for their properties. In this study, the microstructure of six Ni–Cr–Y–Ti–Al powder batches designed for the production of oxide dispersion strengthened nickel were compared. These batches varied in chemistry and atomization technique used which included Gas Atomization Reactive Synthesis (GARS). The batches of powder were then consolidated via Additive Manufacturing (AM) Powder Bed Fusion using Laser Beam (PBF-LB) and characterized via transmission electron microscopy to elucidate the influence of powder feedstock (i.e. synthesis methodology and chemistry) on the PBF-LB microstructure. The study investigates (i) how the amount of yttrium and titanium additions in the powder feedstock and the addition of oxygen during the processing (through GARS) affect the microstructure of the powder itself and the AM printed microstructure, and (ii) how the control of oxygen addition in the printing atmosphere during the PBF-LB printing process itself is another important parameter for achieving the formation of the wanted oxide dispersion versus the stabilization of the cellular structure (often observed in AM processed alloys). Microstructural characterization of both powder particles and additively manufactured nickel alloys in this study provide important insights into the movement of yttrium within the material upon solidification, particularly along cell boundaries, and how yttrium behaves depending on alloy chemistry. When a threshold of yttrium content is reached within the system, yttrium consistently reacts to form an intermetallic along cell boundaries instead of forming oxide nanoparticles.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Stress-controlled fatigue of HfNbTaTiZr high-entropy alloy and associated deformation and fracture mechanisms

The stress-controlled fatigue tests are carried out at a stress ratio of 0.1 and a frequency of 10 Hz, and span both low-cycle and high-cycle regimes by varying the applied stress amplitudes. The high-cycle fatigue regime gives a fatigue strength of 497 MPa and a fatigue ratio of 0.44. At equivalent conditions, the alloy's fatigue strength is greater than all other high-entropy alloys (HEAs) with reported high-cycle fatigue data, dilute body-centered cubic alloys, and many structural alloys such as steels, titanium alloys, and aluminum alloys. Through in-depth analyses of crack-propagation trajectories, fracture-surface morphologies and deformation plasticity by means of various microstructural analysis techniques and theoretical frameworks, the alloy's remarkable fatigue resistance is attributed to delayed crack initiation in the high-cycle regime, which is achieved by retarding the formation of localized persistent slip bands, and its good resistance to crack propagation in the low-cycle regime, which is accomplished by intrinsic toughening backed up by extrinsic toughening. Additionally, the stochastic nature of the fatigue data is neatly captured with a 2-parameter Weibull model.

36 MATERIALS SCIENCE↗