SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Scandium added to Al–Cu–Mg–Ag alloys leads to an in situ phase transformation of coherent Cu-rich nanoprecipitates at elevated temperature, with Sc atoms diffusing and occupying their interstitial sites. Notably, the transformed nanoprecipitates have enhanced thermal stability while maintaining a large volume fraction and these two microstructural features enable high tensile strength of the Al alloy with creep resistance up to 400 °C.
ABSTRACT We present the largest low frequency (120 MHz) arcminute resolution image of the radio synchrotron background (RSB) to date, and its corresponding angular power spectrum of anisotropies (APS) with angular scales ranging from 3° to 0.3 arcmin. We show that the RSB around the north celestial pole has a significant excess anisotropy power at all scales over a model of unclustered point sources based on source counts of known source classes. This anisotropy excess, which does not seem attributable to the diffuse Galactic emission, could be linked to the surface brightness excess of the RSB. To better understand the information contained within the measured APS, we model the RSB varying the brightness distribution, size, and angular clustering of potential sources. We show that the observed APS could be produced by a population of faint clustered point sources only if the clustering is extreme and the size of the Gaussian clusters is ≲1 arcmin. We also show that the observed APS could be produced by a population of faint diffuse sources with sizes ≲1 arcmin, and this is supported by features present in our image. Both of these cases would also cause an associated surface brightness excess. These classes of sources are in a parameter space not well probed by even the deepest radio surveys to date.
The ANSWERS WIMS reactor physics code is being developed for whole core multi-physics modelling. The established neutronics capability for lattice calculations has recently been extended to be suitable for whole core modelling of Small Modular Reactors (SMRs). A whole core transport, SP3 or diffusion flux solution is combined with fuel assembly resonance shielding. An integrated thermal hydraulic solver permits temperature and density variations to feedback to the neutronics calculation. This capability can be applied to both steady state and time dependent transient problems. Nuclear reactor design and safety case development requires assessment of a range of reactor transients, to inform both normal operation limitations and accident scenario analysis. This paper presents new methodology developed in WIMS to couple the core neutronics to the integrated core thermal hydraulics solver for the simulation of reactor transients in whole core models. To support the validation of the multi-physics capability of WIMS, this capability has been applied to the reactivity insertion transient experiments performed in the plate fuelled SPERT-IV reactor. This study employs WIMS using the whole core solver MERLIN, which calculates the time-dependent flux distribution and magnitude, coupled to ARTHUR, which solves for the time-dependent thermal hydraulics solution, and provides thermal feedback via the cross sections generated by GEOM, which performs resonance shielding calculations and generates cross section data for the plate geometry. This spatial kinetics model, with dynamic cross section generation, allows for variations in the temperature and neutron flux profile with time.
Zirconium (Zr) alloys have excellent mechanical properties at high temperature and are resistant to corrosion in different environmental conditions. These alloys are used as tritium (3H or T) getters in nuclear reactors due to their low absorption cross section to thermal neutrons and excellent thermo-mechanical properties. Zr alloys have better mechanical and thermal properties than many other refractory alloys including stainless steel. After the irradiation of TPBAR by neutron flux, 3H produced during irradiation diffuses though the pellets and is captured by the getter. 3H chemically reacts with Zr metal to form metal hydride (ZrTx). Hydrides thus formed are brittle and adversely affect the mechanical and thermal properties of alloys. The lattice mismatch at the interface of alloy and metal hydrides also creates a stress that significantly reduces the alloy’s performance and operation life. Therefore, understanding the behavior of 3H and its species becomes significant as fuel burnup is increased, which leads to increase in hydrogen pickup and oxide formation.
We report despite having a lower energy density than common batteries, electric double-layer capacitors (EDLCs) offer several advantages for high-power applications, including high power density, quick charge and discharge time, and long cycle life. Room-temperature ionic liquids (RTILs) have been intensely studied as promising electrolytes for applications in ELDCs because of their wide potential window, low volatility, as well as thermal and chemical stability. The main deficiency of neat RTILs in such applications is the sluggish diffusivity, which restricts the EDLCs’ power density. To alleviate the slow diffusivity, RTILs can be used in a mixture with organic solvents. In this study, we applied two-dimensional exchange nuclear magnetic resonance spectroscopy (2D EXSY NMR) and molecular dynamics (MD) simulations to investigate the diffusivity of anions of an RTIL, namely, 1-butyl-3-methyl-imidazolium bis(trifluoromethylsulfonyl)imide (BMIM + –TFSI – ), dissolved in five different organic solvents, in the micropores of activated carbon. We determined that the relative concentrations of ions in solutions in the micropores were higher than those in the bulk solutions and were also solvent-dependent. The ion diffusivities in the pores were found to be almost 2 orders of magnitude slower than in the bulk solutions, with methanol showing the largest relative disparity. These results suggested that the interactions of solvents with the activated carbon are critical not only to the power density of EDLCs but also to the energy density. The comparisons of ion diffusivities between the experiments and the MD simulations suggest the need to consider also the surface functionalities of activated carbon for the simulation of ion diffusion in the micropores of activated carbon.
Polymer materials are used widely as sealing materials and liners in hydrogen storage and transportation infrastructure. During operating conditions, polymers are exposed to high pressure hydrogen gas periodically. When in contact, the hydrogen gas diffuses through the polymer material with ease due to its smaller sized molecules compared to the polymer molecules. In the event of rapid decompression of outside hydrogen gas, the hydrogen molecules within the polymer diffuse out. This process is known as the desorption of polymer and can cause blisters or cracking causing permanent damage to the polymer. Here, we used a combined experimental and modeling approach to investigate the desorption of the hydrogen gas in the polymer. Thermal desorption analysis (TDA) experiments were performed on the polymer sample exposed to the high-pressure hydrogen gas to measure the diffusion coefficient and equilibrium hydrogen concentration. Experiments also provided the quantity of hydrogen within the polymer during the desorption process which followed Fick’s law. However, for higher pressurization values, some anomaly was observed in the quantity of hydrogen remaining in the polymer sample. A continuum mechanics based coupled diffusion–deformation-damage model was deployed to simulate the gas desorption process in the material using the finite element method to understand its effect on the material. It was found that the anomaly in TDA results were due to the blister formation on the polymer surface which resulted in longer hydrogen retention. Simulations also showed that blister formation can be affected by multiple parameters such as the addition of filler particles, and pre-existing cavity size.
Hot-water storage in residential and commercial tanks is of growing interest for peak-shifting the electrical demand associated with hot-water loads. How the water enters the tank can significantly affect the extraction efficiency of the storage. Vertical-tube inlets (VTIs) direct cold water into the tank. The VTI design influences whether large-scale mixing occurs, which can reduce the delivery capacity of the hot-water storage. In this work, the mixing at the VTI discharge was characterized by the eddy diffusivity factor (EDF) in an allometric curve fit to the ratio Re:Ri using inlet superficial velocities. The full experimental campaign tested VTI's with Re’s between 170 and 22,300 and Ri's between 0 and 376. Animated visualization of the experimentally measured data is provided, showing tank temperature evolution during inlet flows. The most predictive correlations for EDF are for VTI Re in the transition zone (i.e. ~2300 < Re < ~10,000) and at a Ri corresponding to a stably stratified tank (i.e. Ri > 5). For vertical-tubes that distribute cold water below the thermocline, increasing the EDF will decrease the stratification in a hot-water tank as EDF quantifies inlet mixing. Overall, the new correlations for VTIs can be used to design and model thermally-stratified storage tanks.
Solid-state sodium-ion batteries (SSNIBs) have emerged as a promising alternative to lithium-ion systems for grid-scale energy storage, owing to sodium's abundance and the improved safety of solid-state designs. Among various solid-state electrolytes (SSEs), halide-based Na + SSEs offer high electrochemical stability but are limited by low ionic conductivity and poor thermal stability. Herein, a novel class of sodium hafnium chalcohalide SSEs is reported with a dual-anion (S 2− /Cl − ) framework, with a high ionic conductivity of 4.5 × 10 −4 S cm −1 . The incorporation of sulfur enhances Na⁺ mobility by reducing the migration barrier through increased anion polarizability and expanded diffusion pathways. Additionally, S 2− contributes to stronger interatomic bonding, leading to higher cohesive energy density, improved thermal stability, and mechanical robustness. These SSEs exhibit minimal sulfur oxidation and excellent chemical/electrochemical interface stability with different cathode materials, such as O3-layered NaNi 1/3 Fe 1/3 Mn 1/3 O 2 , P2/O3 layered Na 0.85 Mn 0.5 Ni 0.4 Fe 0.1 O 2 , and Na 3 V 2 (PO 4 ) 3 cathodes. As a result, SSNIBs with P2/O3 layered Na 0.85 Mn 0.5 Ni 0.4 Fe 0.1 O 2 employing the sodium hafnium chalcohalide SSEs demonstrate outstanding cycling performance, achieving a capacity retention of 88.5% after 200 cycles at 0.1 C. This study establishes a new design strategy for high-performance SSEs, demonstrating that mixed-anion frameworks offer a viable route to overcome the intrinsic limitations of single-anion electrolytes in next-generation SSNIBs.
We present full-sky maps of the cosmic microwave background (CMB) and polarized synchrotron and thermal dust emission, derived from the third set of Planck frequency maps. These products have significantly lower contamination from instrumental systematic effects than previous versions. The methodologies used to derive these maps follow closely those described in earlier papers, adopting four methods (Commander, NILC, SEVEM, and SMICA) to extract the CMB component, as well as three methods (Commander, GNILC, and SMICA) to extract astrophysical components. Our revised CMB temperature maps agree with corresponding products in the Planck 2015 delivery, whereas the polarization maps exhibit significantly lower large-scale power, reflecting the improved data processing described in companion papers; however, the noise properties of the resulting data products are complicated, and the best available end-to-end simulations exhibit relative biases with respect to the data at the few percent level. Using these maps, we are for the first time able to fit the spectral index of thermal dust independently over 3° regions. We derive a conservative estimate of the mean spectral index of polarized thermal dust emission of β d = 1.55 ± 0.05, where the uncertainty marginalizes both over all known systematic uncertainties and different estimation techniques. For polarized synchrotron emission, we find a mean spectral index of β s = -3.1 ± 0.1, consistent with previously reported measurements. We note that the current data processing does not allow for construction of unbiased single-bolometer maps, and this limits our ability to extract CO emission and correlated components. The foreground results for intensity derived in this paper therefore do not supersede corresponding Planck 2015 products. For polarization the new results supersede the corresponding 2015 products in all respects.
In this work, combinations of NiCoCrAlY APS and high-velocity oxygen fuel (HVOF) bond coatings were deposited on alloy 247 disk substrates with APS yttria-stabilized zirconia (YSZ) top coatings to assess the benefit of air plasma sprayed (APS) ‘flash’ bond coatings. Using 1-h cycles at 1100 °C in air with 10% H 2 O and HVOF-only and APS-only bond coatings as a baseline, it was found that APS flash coatings extended the average coating lifetime by 16% to 35% with the thicker flash coating performing best. Principal component analysis and energy dispersive spectroscopy (EDS) compositional mapping on coatings characterized after 0, 100, 300 and 500 cycles and after failure showed that the Al in the bond coatings was depleted due to both oxidation and back diffusion into the substrate. The APS-only bond coating had significant oxidation throughout the bond coating and was so depleted in Al, that Al diffused from the substrate to the coating. Residual stress maps of the thermally-grown alumina scale were obtained every 100 cycles using photo-stimulated luminescence piezospectroscopy (PLPS) revealing that the Thick Flash coating had the slowest rate of damage accumulation in the oxide scale.
Systematic investigations of electronic energy loss (S e ) effects on pre-existing defects in crystalline silicon (Si) are crucial to provide reliance on the use of ionizing irradiation to anneal pre-existing defects, leading to successful implementation of this technology in the fabrication of Si-based devices. In this regard, the S e effects on nonequilibrium defect evolution in pre-damaged Si single crystals at 300 K has been investigated using intermediate-energy ions (12 MeV O and Si ions) that interact with the pre-damaged surface layers of Si mainly by ionization, except at the end of their range where the nuclear energy loss (S n ) is no longer negligible. Furthermore, under these irradiation conditions, experimental results and molecular dynamics simulations have revealed that pre-existing disorder in Si can be almost fully annealed by subsequent irradiation with intermediate-energy incident ions with S e values as low as 1.5–3.0 keV/nm. Selective annealing of pre-existing defect levels in Si at room temperature can be considered as an effective strategy to mediate the transient enhanced diffusion of dopants in Si. This approach is more desirable than the regular thermal annealing, which is not compatible with the processing requirements that fall below the typical thermal budget.
Designing superlattices of nanocrystals to mimic and extend the properties of atomic crystals has been a long-standing motivation in materials chemistry. Interstitial solid solutions, such as steel, are well-studied atomic lattices in which mobile components move among the interstices. These materials exhibit unique properties, including reversible structural changes and phase transitions. Interstitial solid solutions possess unique dynamic structures and reversible responses, which motivate the creation of their colloidal equivalents. Here, in this study, we report a fully thermo-reversible colloidal interstitial solid solution by combining liquid crystals and nanocrystals functionalized with promesogenic ligands. Mesogen molecules fill and diffuse among the interstices of a superlattice, resulting in a super-large thermal expansivity. The approach uses a modular design of interparticle interactions, allowing control of interparticle distance, microstructure and transition between crystallographic forms.
Understanding gas flows in capillaries has many applications in modeling the transport of gases in nano-structured, porous, or fractured media. A network of capillaries can often approximate these media, and also information on gas-surface interactions obtained from capillary experiments can be used for modeling flows in these media. Experimental data on flows of different mixtures of He-Ar, He-N 2 , and He-air in the slip regime and in stainless steel capillaries at high temperatures were obtained by using a two-bulb apparatus. An accurate expression for the thermal creep slip coefficients with the Lennard-Jones potential parameters and diffuse-specular reflection gas-surface interaction conditions were then used to obtain the accommodation coefficients for the different gases. The experimental data are best described with values of accommodation coefficients in the range of 0.1–0.3 for He and 0.5–1.0 for Ar, N 2 , and air. Further, the use of values in this range is suggested for modeling gaseous flows in capillaries and nano-structured, porous, or fractured media if other direct measured values for a particular medium are unavailable.
Magnetic islands strongly influence cross-field electron transport in magnetized plasmas. In particular, bifurcations of the island topology modify the number and location of O-points, X-points, and separatrix boundaries, thereby altering diffusion pathways. In recent DIII-D experiments, external magnetic perturbations were used to rotate and periodically bifurcate the island on the q = 2 surface, causing a switchback between a q = 2/1-dominated structure and a narrower q = 4/2-dominated structure. To investigate how this topological change affects electron transport, we employ the field line tracing code TRIP3D with an implemented collisional operator. Thermal, tracer electrons launched from O-points, X-points, and outside separatrix boundaries reveal distinct diffusion regimes, including classical, subdiffusive, and superdiffusive behavior, depending on both the dominant island mode and launch location. These results suggest that island bifurcation can alter electron diffusion across rational surfaces, with direct implications for particle confinement. While the present work emphasizes diffusion as a general framework, the findings provide insight into the conditions under which electron trapping into an island or stochastization of the island's separatrix can enable additional mechanisms, such as the generation of energetic electrons.
Radiative properties are critical to quantify radiative energy fluxes between surfaces and in participating media. However, there is limited experimental data on temperature-dependent radiative properties of materials. Herein, this work focuses on experimentally measuring temperature-dependent diffuse reflectance in the near- and mid-infrared spectra (1–20 μm) for ceramic particles with applications as heat-transfer and thermal-storage media in concentrated solar power (CSP) plants. Specifically, a commercially available sintered bauxite proppant, ACCUCAST ID80, and its primary chemical constituents—alumina (Al 2 O 3 ) and silica (SiO 2 )—are measured in powder form using a Fourier transform infrared spectrometer (FTIR) coupled with a specialized diffuse reflectance accessory and a heated stage. Room-temperature diffuse reflectance measurements show increased absorption in tests with greater mass fractions of the ceramic samples. There is a strong correlation in the measured reflectance spectra of ACCUCAST with alumina and silica in the spectral range 2000–500 cm –1 (5–20 μm). Whereas, for shorter wavelengths (< 5 μm), the absorptance for ACCUCAST is greater than the absorptance for alumina and silica, indicating contributions from other chemical species present in the composite material. For the first time, temperature-dependent diffuse reflectance measurements are reported for ACCUCAST up to 1000 °C. These results are compared against those of alumina and silica through the calculation of a thermal emittance. All three materials exhibit a calculated emittance of ~0.9 at room temperature. However, this value decreases to ~0.6 for ACCUCAST and drops to less than 0.4 for alumina and silica at 1000 °C. Thermal cycling in air at 1000 °C resulted in a visible color change from dark grey to light orange for ACCUCAST and a subsequent larger increase in reflectance for wavelengths less than 5 μm as compared to ACCUCAST thermally cycled at 1000 °C in vacuum. Alumina and silica spectra proved to be largely unaffected by thermal cycling under atmospheric conditions. Overall, this study establishes a powerful technique for the characterization of radiative properties of particulate materials as a function of temperature and presents a detailed case study of ACCUCAST, a candidate for next-generation particle-based CSP.
Here in an oxidizing environment, the oxide formed on plutonium (Pu) metal is composed of a plutonium dioxide (PuO 2 ) top layer and a thin cubic plutonium sesquioxide (Pu 2 O 3 ) middle layer. In a reducing environment, the PuO 2 layer auto-reduces to cubic Pu 2 O 3 . The speed and extent of this conversion depend on the combination of temperature and time. While PuO 2 provides a strong diffusion barrier against unwanted Pu corrosion by gaseous species (like hydrogen), Pu 2 O 3 does not, since its crystal structure has chains of oxygen vacancies. The kinetics of the PuO 2 reduction are, therefore, of fundamental interest and enable researchers to better protect Pu from corrosion. In this report, the oxygen-diffusion-limited kinetics of the dioxide to sesquioxide conversion were obtained by dynamically heating a PuO 2 -covered Pu sample from 294 to 418 K in a high-vacuum vessel equipped with an in situ spectroscopic ellipsometer. The physical/chemical constraints in the conversion process were combined with the ellipsometry method of multi-sample analysis to track the percentage of PuO 2 and to compute the extent of Pu 2 O 3 formation. The resulting diffusion coefficients were compared against and then combined with complementary literature data to produce a comprehensive set of kinetic parameters for reliably modeling oxide conversion over a larger temperature range than spanned by prior studies. The extracted thermal activation energy barrier (43.7 kJ/mol) and pre-exponential factor (5.0 × 10 -10 cm 2 /s) for the oxygen-diffusion-limited process can be used to accurately model the PuO 2 to Pu 2 O 3 transformation in vacuum and/or inert gas applications.
In this work we image charge carrier transport over nanometers–micrometers and picoseconds–microseconds in halide double perovskites Cs 2 AgBiBr 6 and Cs 2 AgTlBr 6 single crystals using stroboscopic scattering microscopy. Both materials exhibit long, microsecond carrier lifetimes because of their indirect or symmetry-forbidden direct bandgaps. We extract free-charge and trap-limited mobilities near the surface and in the crystal bulk. The free-charge mobilities for both materials (~10–50 cm 2 /(V s)) can reach those reported for archetypal lead halide perovskites. We measure trap densities exceeding 10 17 cm –3 within ~20 nm of the crystal surface. Measurements on freshly cleaved or thermally annealed crystals suggest the traps are primarily halide vacancies that likely form through surface bromine degassing. Although these traps considerably slow charge transport, they are energetically shallow, enabling thermally induced detrapping and mobile carriers over microseconds at room temperature. This defect tolerance yields carrier diffusion lengths exceeding 1 μm even in the presence of large trap densities and under solar excitation conditions where traps are not saturated. These results suggest that halide double perovskites could rival the best lead-based perovskites for photovoltaic and optoelectronic applications.
Yttrium hydride is an optimal choice of moderator material for thermal neutron spectrum reactors requiring small core volumes. The Transformation Challenge Reactor (TCR) program at Oak Ridge National Laboratory (ORNL) aims to develop an additively manufactured microreactor core by leveraging recent advances in materials, manufacturing, data analytics, and high-fidelity modeling and simulation. Yttrium hydride was selected as the moderator material for TCR due to its high moderating power, which enables the spatially efficient reactor design and thermal stability that is superior when compared with zirconium hydride. Hydrogen desorption from yttrium hydride is expected at elevated temperatures, posing safety and performance concerns. As a lifetime component in advanced reactors, appropriate strategies to mitigate hydrogen release from yttrium hydride over long-term reactor operation are required. Understanding hydrogen mobility in yttrium hydride provides the scientific basis for developing a hydrogen barrier for hydride moderator and predicting the hydrogen redistribution within the material during various operational conditions. This study investigated the hydrogen motion in YH 1.87 as a function of temperature ranging from 200 to 1,173 K using incoherent quasielastic neutron scattering (IQNS) at the Spallation Neutron Source (SNS). The results are presented and discussed in terms of hydrogen self-diffusion coefficients, activation energy for translational hydrogen motion, and hydrogen jump distances. Based on the IQNS data, YH 1.87 is found to be stable at high temperatures with no translational H motion below 1,023 K within the IQNS detection limits. In the temperature range of 1,073–1,173 K, hydrogen diffusivity in YH 1.87 is $D = 4.57 X 10^{⁻3} [m^2/s] exp (⁻\frac{1.73[eV]}{RT}$). The hydrogen concentration’s dependence on hydrogen diffusivity is also discussed in this report.