SEARCH · Engineering Papers

Results for “texture (materials)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

All sources NASA NTRS DOE OSTI

NASA NTRS2008

Effect of Upper-Cycle Temperature on the Load-Biased, Strain-Temperature Response of NiTi

Over the past decade, interest in shape memory alloy based actuators has increased as the primary benefits of these solid-state devices have become more apparent. However, much is still unknown about the characteristic behavior of these materials when used in actuator applications. Recently we have shown that the maximum temperature reached during thermal cycling under isobaric conditions could significantly affect the observed mechanical response of NiTi (55 wt% Ni), especially the amount of transformation strain available for actuation and thus work output. This investigation extends that original work to ascertain whether further increases in the upper-cycle temperature would produce additional improvement in the work output of the material, which has a stress-free Af of 113 oC, and to determine the optimum cyclic conditions. Thus, isobaric, thermal-cycle experiments were conducted in the aforementioned alloy at various stress levels from 50-300 MPa using upper-cycle temperatures of 165, 200, 230, 260, 290, 320 and 350 oC. The data indicated that the amount of applied stress influenced the transformation strain available in the system, as would be expected. However, the maximum temperature reached during the thermal excursion also plays a role in determining the transformation strain, with the maximum transformation strain being developed by thermal cycling to 290 oC. In situ, neutron diffraction showed that the differences in transformation strain were related to differences in martensite texture within the microstructure when cycling to different upper-cycle temperatures. Hence, understanding this effect is important to optimizing the operation of SMA-based actuators and could lead to new methods for processing and training shape memory alloys for optimal performance.

Padula, Santo, II↗

NASA NTRSDate not supplied

Exploring rock-regolith interfaces in Jezero crater with Mars 2020 SHERLOC

The Perseverance rover successfully landed in Jezero crater, Mars in February 2021 at the Octavia E. Butler landing site and began its mission to explore and sample an ancient crater lake basin. Principal goals of the Mars 2020 mission include characterizing the geology of Mars and seeking signs of ancient microbial life via the spacecraft cameras and spectroscopic instruments onboard. The Scanning Habitable Environments with Raman and Luminescence for Organics and Chemicals (SHERLOC) instrument is a deep UV Raman spectrometer that utilizes a 248.6nm pulsed laser. Part of SHERLOC is a color camera known as the Wide Angle Topographic Sensor for Operations and eNgineering (WATSON). The SHERLOC suite provides coordinated, spectroscopic and imaging capabilities at high spatial resolution, to detect minerals and organic molecules in microtextural context. By pairing high spatial resolution (~100 μm) resonance Raman and native fluorescence spectroscopy with microscopic imaging in a novel spacecraft capability, SHERLOC enables texture-specific molecular composition measurements of rock and regolith targets on Mars. Coordinated rock-regolith observations illuminate unique insights into weathering processes and thereby to primary properties of rocks in Jezero crater. This work describes the potential of rock-regolith interfaces to preserve unique records of geological processes in Jezero crater and can powerfully supplement observations of the more general rock record on Mars. Linking observations of local rock texture with associated regolith reveals important lithologic information based on the interrelationship between differential weathering behavior and mineralogy, grain size, and cement chemistry. Preliminary observations indicate that the polygonally fractured lithotype common near the Octavia E. Butler landing site may weather by granular disintegration and/or surface creep, a relation that can be uniquely observed at the rock-regolith interface. SHERLOC -specific observations of microtextural and elemental composition transitions presented here trace rock-regolith boundaries at multiple indurated surfaces adjacent to regolith. At these locales, grain-scale based examinations suggest chemical weathering could be related to a variably distributed coating or rind on dark rock targets that may be mafic in composition. Granule deposits overlying widely distributed fine-grained material are also observable. Mineral identifications of each phase are presented, with cross-scale comparisons to the remote insights gained by the SuperCam instrument.

Emily L. Cardarelli↗

NASA NTRS1984

Experiments on water/melt explosions, nature of products, and models of dispersal

Experiments were carried out in a steel pressure device using controlled amounts of water and thermite melt to examine the mechanical energy released on explosive mixing following the initial contact of the two materials. An experimental design was used to allow the direct calculation of the mechanical energy by the dynamic lift of the device as recorded both optically and physically. A large number of experiments were run to accurately determine the optimum mixture of water and melt for the conversion of thermal to mechanical energy. The maximum efficiency observed was about 12% at a water/thermite mass ratio of 0.50. These experiments are the basis for the development of models of hydroexplosions and melt fragmentation. Particles collected from the experimental products are similar in size and shape to pyroclasts produced by much larger hydrovolcanic explosions. Melt rupture at optimum ratios produces very fine particles whereas rupture at high or low water/melt ratios produces large melt fragments. Grain surface textures in the experimental products are also related to the water/melt ratio and the mechanism of explosive mixing. It is thus possible to have qualitative information about the nature of the explosion from the sizes and shapes of the fragments produced.

Sheridan, M. F.↗

NASA NTRS1994

Atomic Oxygen Treatment for Non-Contact Removal of Organic Protective Coatings from Painting Surfaces

Current techniques for removal of varnish (lacquer) and other organic protective coatings from paintings involve contact with the surface. This contact can remove pigment, or alter the shape and location of paint on the canvas surface. A thermal energy atomic oxygen plasma, developed to simulate the space environment in low Earth orbit, easily removes these organic materials. Uniform removal of organic protective coatings from the surfaces of paintings is accomplished through chemical reaction. Atomic oxygen will not react with oxides so that most paint pigments will not be affected by the reaction. For paintings containing organic pigments, the exposure can be carefully timed so that the removal stops just short of the pigment. Color samples of Alizarin Crimson, Sap Green, and Zinc White coated with Damar lacquer were exposed to atomic oxygen. The lacquer was easily removed from all of the samples. Additionally, no noticeable change in appearance was observed after the lacquer was reapplied. The same observations were made on a painted canvas test sample obtained from the Cleveland Museum of Art. Scanning electron microscope photographs showed a slight microscopic texturing of the vehicle after exposure. However, there was no removal or disturbance of the paint pigment on the surface. It appears that noncontact cleaning using atomic oxygen may provide a viable alternative to other cleaning techniques. It is especially attractive in cases where the organic protective surface cannot be acceptably or safely removed by conventional techniques.

Rutledge, Sharon K.↗

NASA NTRS2011

Effect of Upper-Cycle Temperature on the Load-Biased, Strain-Temperature Response of NiTi

Over the past decade, interest in shape memory alloy based actuators has increased as the primary benefits of these solid-state devices have become more apparent. However, much is still unknown about the characteristic behavior of these materials when used in actuator applications. Recently we have shown that the maximum temperature reached during thermal cycling under isobaric conditions could significantly affect the observed mechanical response of NiTi (55 wt% Ni), especially the amount of transformation strain available for actuation and thus work output. The investigation we report here extends that original work to ascertain whether further increases in the upper-cycle temperature would produce additional changes in the work output of the material, which has a stress-free austenite finish temperature of 113 C, and to determine the optimum cyclic conditions. Thus, isobaric, thermal-cycle experiments were conducted on the aforementioned alloy at various stresses from 50-300 MPa using upper-cycle temperatures of 165, 200, 230, 260, 290, 320 and 350 C. The data indicated that the amount of applied stress influenced the transformation strain, as would be expected. However, the maximum temperature reached during the thermal excursion also plays an equally significant role in determining the transformation strain, with the maximum transformation strain observed during thermal cycling to 290 C. In situ neutron diffraction at stress and temperature showed that the differences in transformation strain were mostly related to changes in martensite texture when cycling to different upper-cycle temperatures. Hence, understanding this effect is important to optimizing the operation of SMA-based actuators and could lead to new methods for processing and training shape memory alloys for optimal performance.

Padula, Santo, II↗

NASA NTRSDate not supplied

Mineralogy and Spectroscopy of Mount Etna Lava Flows as an Analogue to Venus

Reports of geologically recent volcanism at Venus [1–3] raise the question of whether Venus is actively resurfacing. Observing the venusian surface is difficult due to the planet’s thick, relatively opaque atmosphere, but emission from the surface is detectable via a few atmospheric windows in the near-infrared (NIR) around 1 μm [4]. Spectroscopy of rocks at these wavelengths varies due to its primary composition and the presence of secondary weathering products [2, 5, 6]. If degree of alteration can be tied to the spectroscopic response, then the weathering of the venusian surface can reveal its age and extent of recent volcanism [2, 7]. Mount Etna on Earth is a potential analogue to Venus that can aid our understanding. The composite volcano is currently active and exhibits a progression of dated lava flows with a range of textures (‘a‘¯a versus p¯ahoehoe flows) and degrees of alteration [8]. While not a perfect analogue due to differing weathering environments, Mount Etna represents a natural age progression of altered basaltic rock [8] that can provide a useful comparison to volcanic structures on Venus. Here we will determine if spectroscopy can determine the alteration state of these flows as a proxy for their age. Future missions to Venus such as VERITAS, En- Vision, and DAVINCI will observe the surface in NIR emissivity. Kirchhoff’s Law holds that e = 1−r, where e is the emissivity and r is the reflectance. NIR emissivity can be reliably calculated from reflectance measurements of rocks [9], so laboratory reflectance spectroscopy is useful to rapidly test potential Venus analogue materials.

Gabriel L. Eggers↗

NASA NTRS1983

Impact versus internal origins for mesosiderites

The textures, mineral compositions, and thermal history of mesosiderites are examined to see whether they are compatible with any kind of impact process or internal process which might produce stony-iron breccias. It was proposed that cratering by metal projectiles is not an adequate origin mechanism since it would not deposit enough metal in the stony-iron breccias. It was also proposed that such mechanisms as accretion of differentiated planitesimals must be considered for mesosiderite origins. But no single model for origins is fully satisfactory. Disruption and reassembly of two colliding bodies could form stony-iron breccias at depth, but, as with the previous models, the easiest way to explain the low olivine of mesosiderites is to postulate derivation from olivine-poor chondritic material. Turbulent metal-crust mixing during core formation and crustal blocks sinking into the core withhold olivine from the breccia but do not explain how the silicate and metal liquids in subgroup IV could have failed to segregate.

Hewins, R. H.↗

NASA NTRS1999

Orientation Effects in ZnO Films Using Off-Axis Sputtering Deposition

ZnO is a wide-band-gap oxide material and has been used in numerous applications. It is also a good substrate for fabricating GaN-based (a blue laser candidate) devices. Off-axis sputtering technique is one of the best techniques in synthesizing oxide materials because negative ion bombardment and particle kinetic energy is greatly reduced when adatoms condense on substrates. Since the sputtered material from the target arrive on the substrate surface at a 90 deg. configuration, which differs from the normal sputtering geometry, it is expected that the film uniformity and composition distributions will be affected. However, the details of these properties and mechanisms have not been well studied. ZnO films are synthesized on (0001) sapphire and quartz substrates by off-axis sputtering deposition in various oxygen/argon mixture ratios and pressures at different temperatures. Substrates and sputtering sources are placed at three different orientations that are orthogonal to each other. The normal direction of a substrate is parallel to the gravity vector and the other is perpendicular to it. Film thickness profiles at different growth orientations are determined using a profimeter. All films grown at high temperatures have highly textured structures on quartz substrates and epitaxially grow on sapphire substrates. Because of this process, the film surface is very smooth. X-ray diffraction, scanning probe microscopy, and Fourier transfer infrared spectroscopy, and electrical measurements will be used to characterize these films. Detailed results will be discussed in the presentation.

Zhu, Shen↗

NASA NTRS2003

Characterization of Al-Cu-Mg-Ag Alloy RX226-T8 Plate

Aluminum-copper-magnesium-silver (Al-Cu-Mg-Ag) alloys that were developed for thermal stability also offer attractive ambient temperature strength-toughness combinations, and therefore, can be considered for a broad range of airframe structural applications. The current study evaluated Al-Cu-Mg-Ag alloy RX226-T8 in plate gages and compared performance with sheet gage alloys of similar composition. Uniaxial tensile properties, plane strain initiation fracture toughness, and plane stress tearing resistance of RX226-T8 were examined at ambient temperature as a function of orientation and thickness location in the plate. Properties were measured near the surface and at the mid-plane of the plate. Tensile strengths were essentially isotropic, with variations in yield and ultimate tensile strengths of less than 2% as a function of orientation and through-thickness location. However, ductility varied by more than 15% with orientation. Fracture toughness was generally higher at the mid-plane and greater for the L-T orientation, although the differences were small near the surface of the plate. Metallurgical analysis indicated that the microstructure was primarily recrystallized with weak texture and was uniform through the plate with the exception of a fine-grained layer near the surface of the plate. Scanning electron microscope analysis revealed Al-Cu-Mg second phase particles which varied in composition and were primarily located on grain boundaries parallel to the rolling direction. Fractography of toughness specimens for both plate locations and orientations revealed that fracture occurred predominantly by transgranular microvoid coalescence. Introduction High-strength, low-density Al-Cu-Mg-Ag alloys were initially developed to replace conventional 2000 (Al-Cu-Mg) and 7000 (Al-Zn-Cu-Mg) series aluminum alloys for aircraft structural applications [1]. During the High Speed Civil Transport (HSCT) program, improvements in thermal stability were demonstrated for candidate aircraft wing and fuselage skin materials through the addition of silver to Al-Cu-Mg alloys based on Al 2519 chemistry [2]. Thermal stability of the resulting Al-Cu-Mg-Ag alloys, C415-T8 and C416-T8, was due to co-precipitation of the thermally stable . (AlCu) and ' (Al2Cu) strengthening phases [1-4]. The strength and toughness behavior was investigated for these alloys produced as 0.090-inch thick rolled sheet in the T8 condition and after various thermal exposures. The mechanical properties were shown to be competitive with conventional aircraft alloys, 2519-T8 and 2618-T8 [2]. During the Integral Airframe Structure (IAS) program, advanced aluminum alloys were examined for use in an integrally stiffened airframe structure where the skin and stiffeners would be machined from plate and extruded frames would be mechanically attached (see Figure 1) [5]. Advantages of integrally stiffened structure include reduced part count, and reduced assembly times compared to conventional built-up airframe structure. The near-surface properties of a thick plate are of significance for a machined integrally stiffened airframe structure since this represents the skin location. Properties measured at the mid-plane of the plate are more representative of the stiffener web. RX226 was developed to exploit strength-toughness improvements and thermal stability benefits of Al-Cu-Mg-Ag alloys in plate gages. This study evaluated the microstructure and properties of three gages of plate produced in the T8 condition.

Lach, Cynthia L.↗

NASA NTRSDate not supplied

Modified Rosenthal Solution for Prediction of In Situ Alloyed GRCop-42 Melt Pool

Literature suggests that the energy needed to in-situ alloy material via additive manufacturing is higher per unit volume than their pre-alloyed counterparts, often despite the in-situ formation of thermodynamically favorable phases. This work, via experiments on in-situ alloyed GRCop-42 (Cu-4 at% Cr-2 at% Nb), will explore the energy needs of an elemental powder blend during in-situ alloying via laser powder bed fusion (LPBF). Empirically derived models will explore the influence of elemental thermophysical properties, net energy of in-situ reactions, and powder characteristics on the resulting LPBF energy demands, weld pool size and shape, and porosity evolution. Additionally, the influence of energy input during printing on the in-situ reaction to form Cr2Nb will be explored. Evolution of Cr2Nb dispersoid and copper grain shape, size, and texture can be related to the temperature reached, cooling rate, and time-as-melt during in-situ alloying via LPBF.

David Scannapieco↗

NASA NTRS2023

Investigating the Effects of Space Weathering in Ryugu Samples Using Coordinated Microanalyses

Airless planetary surfaces are characterized by a distinct lack of an atmosphere or magnetic field, leading to direct exposure to the effects of hypervelocity micrometeoroid impacts and solar wind ion irradiation [1]. These processes, cumulatively known as space weathering, gradually alter the microstructural and chemical properties of the grains on airless surfaces. Signatures of space weathering include vesiculated textures, amorphous grain rims (upper ~100 nm), solar flare tracks, and Fe-bearing nanoparticles (npFe) [2,3]. The accumulation of these microstructural space weathering characteristics, particularly the presence of npFe, alters the spectral properties of airless regoliths resulting in changes in spectral slope and reflectance of the surfaces, and the attenuation of characteristic absorption bands in the visible to near-infrared (Vis-NIR) wavelengths. These spectral changes complicate our ability to accurately interpret the mineralogy of airless bodies via remote sensing spectroscopy [1,4]. Studies of space weathering have primarily focused on anhydrous silicate minerals, reflecting the main components of the available returned samples from the Moon and S-type asteroid Itokawa [3,5,6]. However, our understanding of space weathering of primitive, organic-rich carbonaceous materials is still a work in progress. The Japan Aerospace Exploration Agency (JAXA)’s Hayabusa2 mission offered the first opportunity to directly investigate carbonaceous asteroids by returning samples from C-type asteroid (162173) Ryugu. Initial studies of Ryugu samples show mineralogical similarities to CI chondrites along with surface modifications consistent with space weathering. These surface modifications are primarily in the form of μm-thick silicate melts, amorphized phyllosilicates, glassy spherules, and burst vesicles [3,7]. Here, we report results from coordinated microanalytical techniques to further our understanding of the mineralogy and space weathering of carbonaceous materials.

L E Melendez↗

NASA NTRS2014

Chemical Zoning of Feldspars in Lunar Granitoids: Implications for the Origins of Lunar Silicic Magmas

Fine-scale chemical and textural measurements of alkali and plagioclase feldspars in the Apollo granitoids (ex. Fig. 1) can be used to address their petrologic origin(s). Recent findings suggest that these granitoids may hold clues of global importance, rather than of only local significance for small-scale fractionation. Observations of morphological features that resemble silicic domes on the unsampled portion of the Moon suggest that local, sizable net-works of high-silica melt (>65 wt % SiO2) were present during crust-formation. Remote sensing data from these regions suggest high concentrations of Si and heat-producing elements (K, U, and Th). To help under-stand the role of high-silica melts in the chemical differentiation of the Moon, three questions must be answered: (1) when were these magmas generated?, (2) what was the source material?, and (3) were these magmas produced from internal differentiation. or impact melting and crystallization? Here we focus on #3. It is difficult to produce high-silica melts solely by fractional crystallization. Partial melting of preexisting crust may therefore also have been important and pos-sibly the primary mechanism that produced the silicic magmas on the Moon. Experimental studies demonstrate that partial melting of gabbroic rock under mildly hydrated conditions can produce high-silica compositions and it has been suggested by that partial melting by basaltic underplating is the mechanism by which high-silica melts were produced on the Moon. TEM and SIMS analyses, coordinated with isotopic dating and tracer studies, can help test whether the minerals in the Apollo granitoids formed in a plutonic setting or were the result of impact-induced partial melting. We analyzed granitoid clasts from 3 Apollo samples: polymict breccia 12013,141, crystalline-matrix breccia 14303,353, and breccia 15405,78

Mills, R. D↗

NASA NTRS2015

Potential Cement Phases in Sedimentary Rocks Drilled by Curiosity at Gale Crater, Mars

The Mars Science Laboratory rover Curiosity has encountered a variety of sedimentary rocks in Gale crater with different grain sizes, diagenetic features, sedimentary structures, and varying degrees of resistance to erosion. Curiosity has drilled three rocks to date and has analyzed the mineralogy, chemical composition, and textures of the samples with the science payload. The drilled rocks are the Sheepbed mudstone at Yellowknife Bay on the plains of Gale crater (John Klein and Cumberland targets), the Dillinger sandstone at the Kimberley on the plains of Gale crater (Windjana target), and a sedimentary unit in the Pahrump Hills in the lowermost rocks at the base of Mt. Sharp (Confidence Hills target). CheMin is the Xray diffractometer on Curiosity, and its data are used to identify and determine the abundance of mineral phases. Secondary phases can tell us about aqueous alteration processes and, thus, can help to elucidate past aqueous environments. Here, we present the secondary mineralogy of the rocks drilled to date as seen by CheMin and discuss past aqueous environments in Gale crater, the potential cementing agents in each rock, and how amorphous materials may play a role in cementing the sediments.

Rampe, E. B.↗

NASA NTRS1989

Tissue simulating gel for medical research

A tissue simulating gel and a method for preparing the tissue simulating gel are disclosed. The tissue simulating gel is prepared by a process using water, gelatin, ethylene gylcol, and a cross-linking agent. In order to closely approximate the characteristics of the type of tissue being simulated, other material has been added to change the electrical, sound conducting, and wave scattering properties of the tissue simulating gel. The result of the entire process is a formulation that will not melt at the elevated temperatures involved in hyperthermia medical research. Furthermore, the tissue simulating gel will not support mold or bacterial growth, is of a sufficient mechanical strength to maintain a desired shape without a supporting shell, and is non-hardening and non-drying. Substances were injected into the tissue simulating gel prior to the setting-up thereof just as they could be injected into actual tissue, and the tissue simulating gel is translucent so as to permit visual inspection of its interior. A polyurethane spray often used for coating circuit boards can be applied to the surface of the tissue simulating gel to give a texture similar to human skin, making the tissue simulating gel easier to handle and contributing to its longevity.

Companion, John A.↗

NASA NTRS1991

Tissue simulating gel for medical research

A tissue simulating gel and a method for preparing the tissue simulating gel are disclosed. The tissue simulating gel is prepared by a process using water, gelatin, ethylene glycol, and a cross-linking agent. In order to closely approximate the characteristics of the type of tissue being simulated, other material has been added to change the electrical, sound conducting, and wave scattering properties of the tissue simulating gel. The result of the entire process is a formulation that will not melt at the elevated temperatures involved in hyperthermia medical research. Furthermore, the tissue simulating gel will not support mold or bacterial growth, is of a sufficient mechanical strength to maintain a desired shape without a supporting shell, and is non-hardening and non-drying. Substances have been injected into the tissue simulating gel prior to the setting-up thereof just as they could be injected into actual tissue, and the tissue simulating gel is translucent so as to permit visual inspection of its interior. A polyurethane spray often used for coating circuit boards can be applied to the surface of the tissue simulating gel to give a texture similar to human skin, making the tissue simulating gel easier to handle and contributing to its longevity.

Companion, John A.↗

NASA NTRS1995

NASA-UVA Light Aerospace Alloy and Structures Technology program (LA2ST)

The objective of the LA2ST Program is to conduct interdisciplinary graduate student research on the performance of next generation, light-weight aerospace alloys, composites, and thermal gradient structures in collaboration with NASA-Langley researchers. The general aim is to produce relevant data and basic understanding of material mechanical response, environment/corrosion behavior, and microstructure; new monolithic and composite alloys; advanced processing methods; new solid and fluid mechanics analyses; measurement and modeling advances; and a pool of educated students for aerospace technologies. Specific technical objectives are presented for each of the following research projects: time-temperature dependent fracture in advanced wrought ingot metallurgy, and spray deposited aluminum alloys; cryogenic temperature effects on the deformation and fracture of Al-Li-Cu-In alloys; effects of aging and temperature on the ductile fracture of AA2095 and AA2195; mechanisms of localized corrosion in alloys 2090 and 2095; hydrogen interactions in aluminum-lithium alloys 2090 and selected model alloys; mechanisms of deformation and fracture in high strength titanium alloys (effects of temperature and hydrogen and effects of temperature and microstructure); evaluations of wide-panel aluminum alloy extrusions; Al-Si-Ge alloy development; effects of texture and precipitates on mechanical property anisotropy of Al-Cu-Mg-X alloys; damage evolution in polymeric composites; and environmental effects in fatigue life prediction - modeling crack propagation in light aerospace alloys.

Starke, Edgar A., Jr.↗

NASA NTRS2002

The Late Pliocene Eltanin Impact: Documentation From Sediment Core Analyses

The expeditions ANT-XII/4 (1995) and ANT-XVIII/5a (2001) of the RV POLARSTERN collected extensive bathymetric and seismic data sets as well as sediment cores from an area in the Bellingshausen Sea (eastern Pacific Southern Ocean) that allow the first comprehensive geoscientific documentation of an asteroid impact into a deep ocean (approx. 5 km) basin, named the Eltanin impact. Impact deposits have now been recovered from a total of more than 20 sediment cores collected in an area covering about 80,000 km2. Combined biomagnetostratigraphic dating places the impact event into the earliest Matuyama Chron, a period of enhanced climate variability. Sediment texture analyses and studies of sediment composition including grain size and microfossil distribution reveal the pattern of impact- related sediment disturbance and the sedimentary processes immediately following the impact event. The pattern is complicated by the San Martin Seamounts (approx. 57.5 S, 91 W), a large topographic elevation that rises up to 3000 m above the surrounding abyssal plain in the area affected by the Eltanin impact. The impact ripped up sediments as old as Eocene and probably Paleocene that have been redeposited in a chaotic assemblage. This is followed by a sequence sedimented from a turbulent flow at the sea floor, overprinted by fall-out of airborne meteoritic ejecta that settled trough the water column. Grain size distribution reveals the timing and interaction of the different sedimentary processes. The gathered estimate of ejecta mass deposited over the studied area, composed of shock-melted asteroidal material and unmelted meteorites including fragments up to 2.5 cm in diameter, point to an Eltanin asteroid larger than the 1 km in diameter size originally suggested as a minimum based on the ANT-XII/4 results. This places the energy released by the impact at the threshold of those considered to cause environmental disturbance at a global scale and it makes the impact a likely transport mechanism explaining the presence of extinct Cenozoic microfossils in the transantarctic Sirius Unit. Although a crater structure representing Eltanin ground zero has not been discovered, the distribution pattern of sediment disturbance and ejecta deposits now allows to better determine the central target area north of the San Martin Seamounts.

Gersonde, R.↗

NASA NTRS2012

Space Weathering Products Found on the Surfaces of the Itokawa Dust Particles: A Summary of the Initial Analysis

Surfaces of airless bodies exposed to interplanetary space gradually have their structures, optical properties, chemical compositions, and mineralogy changed by solar wind implantation and sputtering, irradiation by galactic and solar cosmic rays, and micrometeorite bombardment. These alteration processes and the resultant optical changes are known as space weathering [1, 2, 3]. Our knowledge of space weathering has depended almost entirely on studies of the surface materials returned from the Moon and regolith breccia meteorites [1, 4, 5, 6] until the surface material of the asteroid Itokawa was returned to the Earth by the Hayabusa spacecraft [7]. Lunar soil studies show that space weathering darkens the albedo of lunar soil and regolith, reddens the slopes of their reflectance spectra, and attenuates the characteristic absorption bands of their reflectance spectra [1, 2, 3]. These changes are caused by vapor deposition of small (<40 nm) metallic Fe nanoparticles within the grain rims of lunar soils and agglutinates [5, 6, 8]. The initial analysis of the Itokawa dust particles revealed that 5 out of 10 particles have nanoparticle-bearing rims, whose structure varies depending on mineral species. Sulfur-bearing Fe-rich nanoparticles (npFe) exist in a thin (5-15 nm) surface layer (zone I) on olivine, low-Ca pyroxene, and plagioclase, suggestive of vapor deposition. Sulfur-free npFe exist deeper inside (<60 nm) ferromagnesian silicates (zone II). Their texture suggests formation by amorphization and in-situ reduction of Fe2+ in ferromagnesian silicates [7]. On the other hand, nanophase metallic iron (npFe0) in the lunar samples is embedded in amorphous silicate [5, 6, 8]. These textural differences indicate that the major formation mechanisms of the npFe0 are different between the Itokawa and the lunar samples. Here we report a summary of the initial analysis of space weathering of the Itokawa dust particles.

Noguchi, T.↗