Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “pore pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

High temperature oxidation behaviors of bulk SiC with low partial pressures of air and water vapor in argon

Oxidation behaviors of bulk SiC at 1000–1400 °C in Ar-20 vol% H 2 O-10 vol% air were investigated. The thickness of the passivation oxide layer showed a parabolic increase with time. Dense and uniform layers formed below 1200 °C, whereas pores and cracks were observed at higher temperatures. An analytical model was proposed to estimate the oxide layer growth and SiC mass loss rate. The SiC layer should be effective in retaining the fission products after oxidation by excessive water and air. This work is the first detailed study of SiC layer oxidation during loss of coolant accidents (LOCA) for HTGRs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Assessing the potential of composite confining systems for secure and long-term CO 2 retention in geosequestration

A potential geologic target for CO 2 storage should ensure secure containment of injected CO 2 . Traditionally, this objective has been achieved by targeting reservoirs with overlying seals-regionally extensive, low permeability units that have been proven capable of retaining buoyant fluid accumulations over geologic time. However, considering that the amount of CO 2 is limited by a decadal injection period, vertical migration of CO 2 can be effectively halted by a composite system of discontinuous shale/silt/mudstone barriers in bedded sedimentary rocks. Here, we studied the impact of depositional architectures in a composite confining system on CO 2 migration and confinement at reservoir scale. We stochastically generated lithologically heterogeneous reservoir models containing discontinuous barriers consistent with statistical distributions of net-sand-to-gross-shale ratio (NTG) and horizontal correlation lengths derived from well log data and observations of producing hydrocarbon fields in Southern Louisiana. We then performed an extensive suite of reservoir simulations of CO 2 injection and post-injection to evaluate the sensitivity of CO 2 plume migration and pressure response of the composite system to a series of geologic and fluid parameters including the lateral continuity of barriers, NTG, permeability anisotropy within the sand body, and capillary pressure contrast between the sand and shale facies. The results indicate that lateral continuity of barriers and NTG are the dominant controls on CO 2 plume geometry and pressure build-up in the reservoir, while the impact of NTG is particularly pronounced. The significance of intraformational barriers becomes apparent as they facilitate the local capillary trapping of CO 2 . Those barriers improve the pore space occupancy by promoting a more dispersed shape of the plume and ultimately retard the buoyancy-driven upward migration of the plume post injection.

58 GEOSCIENCES↗
NASA NTRS2015

Constraining the Texture and Composition of Pore-Filling Cements at Gale Crater, Mars

The Mars Science Laboratory (MSL) rover Curiosity has encountered a wide variety of sedimentary rocks deposited in fluvio-lacuestrine sequences at the base of Gale Crater. The presence of sedimentary rocks requires that initial sediments underwent diagenesis and were lithified. Lithification involves sediment compaction, cementation, and re-crystallization (or authigenic) processes. Analysis of the texture and composition of the cement can reveal the environmental conditions when the cements were deposited, enabling better understanding of early environments present within Gale Crater. The first step in lithification is sediment compaction. The Gale crater sediments do not show evidence for extensive compaction prior to cementation; the Sheepbed mudstone in Yellowknife Bay (YKB) has preserved void spaces ("hollow nodules"), indicating that sediments were cemented around the hollow prior to compaction, and conglomerates show imbrication, indicating minimal grain reorganization prior to lithification. Furthermore, assuming the maximum burial depth of these sediments is equivalent to the depth of Gale Crater, the sediments were never under more than 1 kb of pressure, and assuming a 15 C/km thermal gradient in the late Noachian, the maximum temperature of diagenesis would have been approximately 75 C. This is comparable to shallow burial diagenetic conditions on Earth. The cementation and recrystallization components of lithification are closely intertwined. Cementation describes the precipitation of minerals between grains from pore fluids, and recrystallization (or authigenesis) is when the original sedimentary mineral grains are altered into secondary minerals. The presence of authigenic smectites and magnetite in the YKB formation suggests that some recrystallization has taken place. The relatively high percentage of XRD-amorphous material (25-40%) detected by CheMin suggests that this recrystallization may be limited in scope, and therefore may not contribute significantly to the cementing material. However, relatively persistent amorphous components could exist in the Martian environment (e.g. amorphous MgSO4), so recrystallization, including loss of crystallinity, cannot yet be excluded as a method of cementation. In order to describe the rock cementation, both the rock textures and their composition must be considered. Here, we attempt to summarize the current understanding of the textural and compositional aspects of the cement across the rocks analyzed by Curiosity to this point.

Siebach, K. L.↗
DOE OSTI2026

Multi-system analysis of offshore geologic carbon storage: a review of open-source data science solutions

Geologic carbon storage projects are maturing worldwide and the footprint of deployment in the offshore is expanding. At present, there are ten projects in operation or that have been completed, more than 50 in construction and development, and dozens of characterization studies completed or underway. Offshore geologic carbon storage offers potential benefits over onshore geologic carbon storage. These offshore projects are generally remote in location, distant from population centers, and avoid complicated pore space rights while having abundant prospective storage potential. Some offshore fields targeted for carbon storage have comparatively fewer prior borehole penetrations except for areas that have been explored for petroleum production, minimizing potential issues such as pressure interference and infrastructure impacts. Yet offshore geologic carbon storage projects face distinctive technical and economic challenges, such as seafloor geohazards (e.g., seabed instability), expensive maritime transport, and meteorological-oceanographic conditions that can damage infrastructure and impact operations. Analytical capabilities and improved computational speeds have advanced engineering, earth and energy sciences in the wake of the arrival of modern data science over the last decade. These advancements have created an opportunity for integrated, multi-systems modeling approaches utilizing artificial intelligence and machine learning that are no longer limited by computational issues. Analytical tools developed alongside this advancement in data science can be leveraged to calibrate the potential advantages and challenges of carbon storage operations in the offshore. New methods and approaches that incorporate data science to analyze multiple aspects of engineered and natural systems can provide insights that complement the characterization and onsite engineering that traditional commercial and operational software addresses. These new methods and approaches can potentially improve the outcome of energy operations and carbon storage. Providing multi-system, science-driven data analytics enhances the knowledge base that offshore developers, operators, and regulatory bodies may draw from to improve offshore site selection and operational efficiency. Here, we provide a brief synopsis of geologic carbon storage efforts to date, an overview of the engineered and natural systems involved in offshore geologic carbon storage, and a review of publicly available, open-source, offshore and/or carbon storage related data- and science-driven tools developed by 2010 or later that are suitable for screening and assessing regions for offshore geologic carbon storage.

artificial intelligence↗
NASA NTRS1989

Design considerations for a micro-g superfluid helium fluid acquisition system

The general description, the operation, and the design of a superfluid helium (SFHe) fluid acquisition system (FAS) for use under microgravity conditions is presented. For the type of FAS considered here, where fine-mesh woven screens are used to retain flowing SFHe within a gallery arm (flow) channel, those forces which determine the flow dynamics are the micro-g accelerations, liquid surface tension, and tensile strength and cumulative pressure drops along a flow path that begins at the bulk liquid and ends at the entrance to a pump. For this case, the dimensionless number, N(T) is written as the ratio between the pressure drop across the screen and the surface tension forces at the screen for low fluid velocities. Static Bond number measurements have bene taken for SFHe using 325 x 2300 twilled Dutch screen and have indicated a screen pore hydraulic radius of 0.00031 cm.

Lee, J. M.↗
DOE OSTI2023

Synthesis and Characterization of Carbon Microbeads

We report a microfluidic-based droplet generation platform for synthesizing micron-sized porous carbon microspheres. The setup employs carbon materials such as graphite, carbon nanotubes, graphene, fullerenes, and carbon black as starting materials. Custom composition, structure, and function are achieved through combinations of carbon materials, cross-linkers, and additives along with variations in process parameters. Carbon materials can be assembled into spheres with a mean diameter of units to hundreds of μm with relatively tight size distribution (<25% RSD). Pore structure and size (tens to hundreds of angstrom) can be modulated by incorporating porogen/coporogen dilutants during synthesis. The microbeads have excellent mechanical stability with an elastic modulus of hundreds of MPa. They can sustain high dynamic fluid flow pressures of up to 9000 psi. This work lays the foundation for synthesizing novel tailorable and customizable carbon microbeads. It opens avenues for applying these novel materials for composite and additive manufacturing, energy, life science, and biomedical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1997

Ultrasound Algorithm Derivation for Soil Moisture Content Estimation

Soil moisture content can be estimated by evaluating the velocity at which sound waves travel through a known volume of solid material. This research involved the development of three soil algorithms relating the moisture content to the velocity at which sound waves moved through dry and moist media. Pressure and shear wave propagation equations were used in conjunction with soil property descriptions to derive algorithms appropriate for describing the effects of moisture content variation on the velocity of sound waves in soils with and without complete soil pore water volumes, An elementary algorithm was used to estimate soil moisture contents ranging from 0.08 g/g to 0.5 g/g from sound wave velocities ranging from 526 m/s to 664 m/s. Secondary algorithms were also used to estimate soil moisture content from sound wave velocities through soils with pores that were filled predominantly with air or water.

Belisle, W.R.↗
NASA NTRS1976

Ocean foam generation and modeling

A laboratory investigation was conducted to determine the physical and microwave properties of ocean foam. Special foam generators were designed and fabricated, using porous glass sheets, known as glass frits, as the principal element. The glass frit was sealed into a water-tight vertical box, a few centimeters from the bottom. Compressed air, applied to the lower chamber, created ocean foam from sea water lying on the frit. Foam heights of 30 cm were readily achieved, with relatively low air pressures. Special photographic techniques and analytical procedures were employed to determine foam bubble size distributions. In addition, the percentage water content of ocean foam was determined with the aid of a particulate sampling procedure. A glass frit foam generator, with pore diameters in the range 70 - 100 micrometers, produced foam with bubble distributions very similar to those found on the surface of natural ocean foam patches.

Porter, R. A.↗
NASA NTRS2002

Oxidation Behavior of GRCop-84 Copper Alloy Assessed

NASA's goal of safe, affordable space transportation calls for increased reliability and lifetimes of launch vehicles, and significant reductions of launch costs. The areas targeted for enhanced performance in the next generation of reusable launch vehicles include combustion chambers and nozzle ramps; therefore, the search is on for suitable liner materials for these components. GRCop-84 (Cu-8Cr-4Nb), an advanced copper alloy developed at the NASA Glenn Research Center in conjunction with Case Western Reserve University, is a candidate. The current liner of the Space Shuttle Main Engine is another copper alloy, NARloy-Z (Cu-3Ag-0.1Zr). It provides a benchmark against which to compare the properties of candidate successors. The thermomechanical properties of GRCop-84 have been shown to be superior, and its physical properties comparable, to those of NARloy-Z. However, environmental durability issues control longevity in this application: because copper oxide scales are not highly protective, most copper alloys are quickly consumed in oxygen environments at elevated temperatures. In consequence, NARloy-Z and most other copper alloys are prone to blanching, a degradation process that occurs through cycles of oxidation-reduction as the oxide is repeatedly formed and removed because of microscale fluctuations in the oxygen-hydrogen fuel systems of rocket engines. The Space Shuttle Main Engine lining typically degraded by blanching-induced hot spots that lead to surface roughening, pore formation, and coolant leakage. Therefore, resistance to oxidation and blanching are key requirements for second-generation reusable launch vehicle liners. The rocket engine ambient includes H2 (fuel) and H2O (combustion product) and is, hence, under reduced oxygen partial pressures. Accordingly, our studies were expanded to include oxygen partial pressures as low as 322 parts per million (ppm) at the temperatures likely to be experienced in service. A comparison of 10-hr weight gains of GRCop-84, NARloy-Z, and pure copper in 0.032, 2.2, and 100 percent oxygen from 550 to 750 C is shown. In 2.2 vol% and higher oxygen content, GRCop-84 oxidation was slower than that of NARloy-Z or Cu, but that advantage was lost or diminished in 322-ppm O2. Over longer (50-hr) exposures in 1.0 atm O2, however, the advantage of GRCop-84 increased significantly, its oxidation rate becoming approximately 10 times slower than those of Cu and NARloy-Z from 500 to 700 C. Weight gains were moderate and the kinetics parabolic for all three materials in 2.2 vol% and higher oxygen content; however, in 322-ppm O2, the scales were nonprotective below about 650 C, as reflected in linear kinetics and large weight gains. The superior oxidation resistance of GRCop-84 is likely related to the kinetics of extra oxygen consumption to form the additional oxides of Cr and Nb detected beneath the GRCop-84 oxide layer. While we continue to evaluate the blanching resistance of GRCop-84 in other tests, these oxidation results indicate that GRCop-84 is suitable as a reusable launch vehicle liner, and in applications where it is desired to use a copper alloy but without the risk of oxidative failure. Three bar charts comparing overall specific weight gains by each of the three materials studied. The top chart is for oxidation in 1.0 atm of oxygen, the middle is for 2.2% oxygen (balance argon), and the bottom is for 0.0322% oxygen. GRCop-84 outperforms the other two materials, showing the least weight gain in nearly all cases.

Thomas-Ogbuji, Linus U.↗
DOE OSTI2024

Chemical and Electrochemical Characterization of Hot–Pressed Li 6 PS 5 Cl Solid State Electrolyte: Operating Pressure–Invariant High Ionic Conductivity

Sulfide solid state electrolytes (SSE) are among the most promising materials in the effort to replace liquid electrolytes, largely due to their comparable ionic conductivities. Among the sulfide SSEs, Argyrodites (Li 6 PS 5 X, X=Cl, Br, I) further stand out due to their high theoretical ionic conductivity (~1×10 –2 S cm –1 ) and interfacial stability against reactive metal anodes such as lithium. Generally, solid state electrolyte pellets are pressed from powder feedstock at room temperature, however, pellets fabricated by cold pressing consistently result in low bulk density and high porosity, facilitating interfacial degradation reactions and allowing dendrites to propagate through the pores and grain boundaries. Here, we demonstrate the mechanical and electrochemical implications of hot-pressing standalone LPSCl SSE pellets with near-theoretical ionic conductivity, superior cycling performance, and enhanced mechanical stability. X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and x-ray diffraction spectroscopy (XRD) analysis reveal no chemical changes to the Argyrodite surface after hot pressing up to 250°C. Furthermore, we use electrochemical impedance spectroscopy (EIS) to understand mechanical stability of Argyrodite SSE pellets as a function of externally applied pressure, demonstrating for the first time pressed standalone Argyrodite pellets with near-theoretical conductivities at external pressures below 14 MPa.

25 ENERGY STORAGE↗
DOE OSTI2022

A two-phase model that unifies and extends the classical models of membrane transport

Two models describe solvent transport through swollen, nonporous membranes. The pore-flow model, based on fluid mechanics, works for porous membranes, whereas the solution-diffusion model invokes molecular diffusion to treat nonporous membranes. Both approaches make valid arguments for swollen polymer membranes, but they disagree in their predictions of intramembrane pressure and concentration profiles. Using a fluid-solid model that treats the solvent and membrane matrix as separate phases, we show both classical models to be valid, to represent complementary approaches to the same phenomenon, and to make identical predictions. The fluid-solid model clarifies recent reverse osmosis measurements; provides a predictive and mechanistic basis for empirical high-pressure limiting flux phenomena, in quantitative agreement with classic measurements; and gives a framework to treat nonporous but mechanically heterogeneous membrane materials.

Science & Technology - Other Topics↗
NASA NTRS1971

The effect of liquid configuration in porous gas electrodes.

Measurement of the influence of differential pressure on electrode activity in oxygen cathodes made up of beds of uniform silver spheres (156 micron diameter). The extent and nature of this dependence could be explained through use of the concept of pendular and funicular liquid configuration in the pore space of the electrode.

Katan, T.↗
DOE OSTI2021

Characterization of shale using Helium and Argon at high pressures

In order to estimate the shale gas in place and the eventual recovery during shale gas operations, one of the key requirements is to accurately characterize the shale’s petrophysical and transport properties such as porosity, permeability, diffusivity, and storage capacity. Despite the many efforts reported in the technical literature aiming to provide an improved understanding of the complex pore structures and the associated fluid flow in gas shales, complete characterization of organic-rich shale samples still poses a big challenge. Here, we have characterized mass transfer and sorption in shale at different length scales using Helium (He) and Argon (Ar) as probe gases. Thermogravimetric analysis (TGA) with a shale cube of ~1 cm 3 in size and gas expansion experiments with a full-diameter core (3.5” in diameter) were used to measure sorption kinetics/isotherms and mass transfer, respectively. Both samples are from the same depth/location in the Marcellus shale formation. The TGA steady-state technique was initially used to generate excess sorption isotherms for Ar, while dynamic TGA experiments were used to study its sorption kinetics. The TGA experiments demonstrate that Ar, which has a similar sorption potential as Methane, but is generally assumed to be inert, adsorbs onto the surfaces of the mesoporous and microporous regions of the shale samples according to a Langmuir-type behavior. Helium expansion experiments, on the full-diameter core, were used to measure the overall porosity, on the basis that He is a non-sorbing and inert gas as compared to Ar. The He expansion experiments, furthermore, allow us to delineate the mass transfer of gas across the inherent hierarchy of pore sizes, including macropores (macro- and microcracks), mesopores and micropores. Similar expansion experiments were also performed with Ar to study the combined impact of mass transfer and sorption. A triple-porosity model (TPM) was utilized to interpret the He expansion experiments with the shale core and to extract (estimate) relevant transport parameters. We report and compare here the diffusivities and permeabilities of the whole core for both He and Ar, as calculated from the modeling and fitting of the experimental data. On the premise that the shale cube is representative of the matrix region of the core, the Ar sorption kinetics from the cube experiments were subsequently combined with the transport parameters extracted from the He experiments to predict the behavior of the Ar expansion test with the full-diameter core. An excellent agreement is observed between the model predictions and the experimental data. The experimental observations and their interpretation indicate that one must be cautious when using Ar to estimate the true porosity and permeability of shales. In addition, we demonstrate that He and Ar probe gases, when used in tandem, can be employed effectively as a tool to characterize shales in terms of mass transfer and sorption dynamics across scales.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2025

Experimental Characterization of Hydrogen Diffusion in Shale Rocks for Geologic Storage Applications

As global energy systems undergo a transition to cleaner alternatives, geologic hydrogen storage has emerged as a promising solution for large-scale energy storage. A critical factor in determining the feasibility of this approach is the effectiveness of caprock formations, such as shale, in preventing hydrogen migration. This study investigates the diffusion behavior of hydrogen through shale to assess its suitability as a caprock for geologic hydrogen storage. Using a novel double-seal core holder design and a through-diffusion apparatus, hydrogen diffusion was measured through shale rock from the Eagle Ford and Wolfcamp Formations under dry conditions. These measurements were complemented by microstructural and mineralogical analyses using low-pressure nitrogen adsorption and X-ray diffraction. The effective diffusion coefficient of hydrogen in these shale caprocks ranged from 2.51 × 10 –8 to 9.85 × 10 –8 m 2 /s. Notably, we observed that the diffusion behavior was more related to the pore network structure and could not be attributed to differences in the total pore volume between shale types alone. Here, to further understand the role of pore network complexity, a fractal pore model was developed to correlate tortuosity with the fractal dimension of the pore structure (a measure of pore network complexity). The proposed model closely matched tortuosity values obtained from diffusion experiments, outperforming existing theoretical tortuosity–porosity correlations. These findings provide key quantitative parameters needed to assess the feasibility of geologic hydrogen storage as well as insights that can be applied to hydrogen storage in a range of geologic formations.

08 HYDROGEN↗
DOE OSTI2021

Validation of strongly coupled geomechanics and gas hydrate reservoir simulation with multiscale laboratory tests

In this work, we validate a coupled flow-geomechanics simulator for gas hydrate deposits, named T+M AM , performing two meter-scale laboratory experiments of gas hydrates for production by depressurization, replicating the gas hydrate deposit in the Ulleung Basin, East Sea, South Korea. The first experiment with a sand-only specimen is a 1D 1 m-scale depressurization test based on the excess gas method, which represents the grain coating hydrate growth. On the other hand, the second is a 3D 1.5 m-scale test with the excess water method for a sand-mud alternating layer system, representing the pore filling hydrate growth. We measure production and displacement at the top with different depressurization levels. In particular, the 3D test exhibits high coupling strength of substantial deformation induced by incompressibility of water and high deformability of the specimen. For validation, we match pressure, flow rate, and displacement between the experimental data and numerical results. Thus, we identify that T+M AM is a reliable simulator, which can be applied to fields in both permafrost and deep oceanic hydrate deposits of strongly coupled flow and geomechanics systems. This validation also implies that other coupled simulators based on the same coupling formulation as T+M AM can be validated when individual flow and geomechanics simulators are stable and reliable.

02 PETROLEUM↗
DOE OSTI2021

Selective penetration behavior of microgels in superpermeable channels and reservoir matrices

Gel treatment is an effective way to attack excessive water production in many mature oilfields around the world. Selective penetration is desired for successful gel treatments. That is, gel materials should easily penetrate the target zones (i.e., channeling features such as superpermeable channels) without entering/damaging the nontarget zones (i.e., reservoir matrices or oil zones). This study revealed that presence of threshold penetration pressure (ΔP th ) was responsible for selective penetration behavior of tested microgels. The concept of ΔP th was utilized to figure out favorable working conditions for effective gel treatments. Microgel dispersions were injected into superpermeable (super-k) sandpacks (mimicking super-k channels in reservoirs, 60–221 darcies), heterogeneous models with super-k channels (79–230 darcies), and sandstone cores (mimicking reservoir matrices, 50–5000 md). The results demonstrated that a minimum differential driving pressure (i.e., threshold penetration pressure, ΔP th ) was required to push microgel particles to penetrate channels or matrices. The critical penetration behavior was closely related to the particle/pore size ratio. Low ΔP th at smaller particle/pore ratios was beneficial to allow easy penetration of gel materials into the channeling zones. On the contrary, high ΔPth at larger particle/pore ratios was desirable to prevent gel materials from massively invading and damaging the matrices. Instead, the gel particles accumulated at the inlet surface, and a gel cake was gradually formed. The cake further prevented the invasion of the gels. The cake could be removed by chemical breakers to resume the injectivity/productivity of the matrices. Correlations were developed to describe the relationship between ΔP th and particle/pore ratio. A distinct transition was identified at the particle/pore ratio of about 3. This research could help identify the favorable conditions to achieve successful gel treatments. In an effective conformance treatment, the particle/pore ratio in the channel should be sufficiently low to allow easy penetration of gel materials into the channel (e.g., particle/pore ratio<2 in this study). Meanwhile, the particle/pore ratio in the matrix should be large enough to support a high ΔP th and thus prevent massive gel invasion into the matrix. This study advances the current pore scale studies (a single particle passing through a single channel) to Darcy-scale characterization.

02 PETROLEUM↗
DOE OSTI2023

Simulation of Reverse Osmosis Membrane Compaction Using Material Point Method (MPM)

Access to fresh drinking water in the future requires effective management of industrial wastewater and water purification from available resources. In this study, we present the simulation methodology and the analysis of a Reverse Osmosis (RO) membrane under various pressure conditions using the Material Point Method (MPM). In contrast to other numerical methods, MPM solves the continuum governing equations on material points in a Lagrangian framework. The method does not require a grid connecting the material points hence making it suitable to simulate large deformations during membrane compaction. The time integration is carried out using the explicit Euler method, while the spatial discretization is performed using linear or cubic-spline shape functions. A series of planar images containing detailed pore structures obtained from X-ray tomography experiments is converted to a three-dimensional collection of material points to simulate the membrane. Compressive loads are applied to the top layer of the membrane to simulate the experiments. The membrane deformation and pore size distribution before and after load application are reported and compared with the experimental measurements. The presentation discusses the numerical methods used, the performance of the solver on high-performance computing machines, and the results of membrane compaction in detail.

ENGINEERING,MATHEMATICS AND COMPUTING↗
NASA NTRS2012

Next-Generation Evaporative Cooling Systems for the Advanced Extravehicular Mobility Unit Portable Life Support System

The development of the Advanced Extravehicular Mobility Unit (AEMU) Portable Life Support System (PLSS) is currently underway at NASA Johnson Space Center. The AEMU PLSS features two new evaporative cooling systems, the Reduced Volume Prototype Spacesuit Water Membrane Evaporator (RVP SWME), and the Auxiliary Cooling Loop (ACL). The RVP SWME is the third generation of hollow fiber SWME hardware, and like its predecessors, RVP SWME provides nominal crewmember and electronics cooling by flowing water through porous hollow fibers. Water vapor escapes through the hollow fiber pores, thereby cooling the liquid water that remains inside of the fibers. This cooled water is then recirculated to remove heat from the crewmember and PLSS electronics. Major design improvements, including a 36% reduction in volume, reduced weight, and more flight like back-pressure valve, facilitate the packaging of RVP SWME in the AEMU PLSS envelope. In addition to the RVP SWME, the Auxiliary Cooling Loop (ACL), was developed for contingency crewmember cooling. The ACL is a completely redundant, independent cooling system that consists of a small evaporative cooler--the Mini Membrane Evaporator (Mini-ME), independent pump, independent feed-water assembly and independent Liquid Cooling Garment (LCG). The Mini-ME utilizes the same hollow fiber technology featured in the RVP SWME, but is only 25% of the size of RVP SWME, providing only the necessary crewmember cooling in a contingency situation. The ACL provides a number of benefits when compared with the current EMU PLSS contingency cooling technology; contingency crewmember cooling can be provided for a longer period of time, more contingency situations can be accounted for, no reliance on a Secondary Oxygen Vessel (SOV) for contingency cooling--thereby allowing a SOV reduction in size and pressure, and the ACL can be recharged-allowing the AEMU PLSS to be reused, even after a contingency event. The development of these evaporative cooling systems will contribute to a more robust and comprehensive AEMU PLSS.

Makinen, Janice V.↗