Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “passivating layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Improving positive and negative bias illumination stress stability in parylene passivated IGZO transistors

The impact of a parylene top-coating layer on the illumination and bias stress instabilities of indium-gallium-zinc oxide thin-film transistors (TFTs) is presented and discussed. The parylene coating substantially reduces the threshold voltage shift caused by continuous application of a gate bias and light exposure. The operational stability improves by 75%, and the light induced instability is reduced by 35%. The operational stability is quantified by fitting the threshold voltage shift with a stretched exponential model. Storage time as long as 7 months does not cause any measurable degradation on the electrical performance. It is proposed that parylene plays not only the role of an encapsulation layer but also of a defect passivation on the top semiconductor surface. It is also reported that depletion-mode TFTs are less sensitive to light induced instabilities. This is attributed to a defect neutralization process in the presence of free electrons.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Low-Temperature Carburization of AL-6XN Enabled by Provisional Passivation

Employing AISI-AL-6XN as example, we introduce a new method of surface activation for low-temperature carburization. This method consists of two steps: (i) removing the passivating surface oxide and a potentially existing severely plastically deformed surface layer (Beilby layer) by aqueous (liquid) hydrochloric acid, and (ii) immersion in ethanol and subsequent drying in nitrogen. Upon carburization with a gas mixture of acetylene, hydrogen, and nitrogen, this new method of surface activation enables the formation of a fully developed “case”, i.e., a uniform solid solution of interstitial carbon in austenite with carbon fractions up to 0.20 near the alloy surface. The underlying mechanism of surface activation is shown to involve the formation of a provisional passivating layer. It consists of chlorides or ethoxides that are insoluble in ethanol. It prevents the reformation of the regular Cr-rich passivating oxide layer and is readily removed upon heating and exposure to the carburizing gas. As the new activation method is quicker, more effective, and less destructive to furnace hardware than activation with hot gaseous hydrochloric acid that is currently applied in industrial manufacturing, it may have considerable technological impact.

Li, Zhen (ORCID:000000017245400X)↗

Protective capping and surface passivation of III-V nanowires by atomic layer deposition

Low temperature (∼200 °C) grown atomic layer deposition (ALD) films of AlN, TiN, Al{sub 2}O{sub 3}, GaN, and TiO{sub 2} were tested for protective capping and surface passivation of bottom-up grown III-V (GaAs and InP) nanowires (NWs), and top-down fabricated InP nanopillars. For as-grown GaAs NWs, only the AlN material passivated the GaAs surface as measured by photoluminescence (PL) at low temperatures (15K), and the best passivation was achieved with a few monolayer thick (2Å) film. For InP NWs, the best passivation (∼2x enhancement in room-temperature PL) was achieved with a capping of 2nm thick Al{sub 2}O{sub 3}. All other ALD capping layers resulted in a de-passivation effect and possible damage to the InP surface. Top-down fabricated InP nanopillars show similar passivation effects as InP NWs. In particular, capping with a 2 nm thick Al{sub 2}O{sub 3} layer increased the carrier decay time from 251 ps (as-etched nanopillars) to about 525 ps. Tests after six months ageing reveal that the capped nanostructures retain their optical properties. Overall, capping of GaAs and InP NWs with high-k dielectrics AlN and Al{sub 2}O{sub 3} provides moderate surface passivation as well as long term protection from oxidation and environmental attack.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Boundary Layer Remote Sensing with Combined Active and Passive Techniques: GPS Radio Occultation and High-Resolution Stereo Imaging (WindCam) Small Satellite Concept

Objective: significant progress in understanding low-cloud boundary layer processes. This is the Single largest uncertainty in climate projections. Radio occultation has unique features suited to boundary layer remote sensing (1) Cloud penetrating (2) Very high vertical resolution (approximately 50m-100m) (3) Sensitivity to thermodynamic variables

stereo camera↗

The tracer-BHR4 model for subgrid mixing layers

A model for the passive evolution of turbulent subgrid-scale mixing layers is developed based on the model of tracer-BHR model of Braun & Gore. The new model, tracer-BHR4, mainly differs from the previous iteration in that it aims to replicate the behavior of BHR4, instead of BHR3.1. The coefficients from BHR4 are used and a new model for mixing layer growth is developed to allow the tracer model to reproduce the de-mixing behavior seen in BHR4. Additionally, an improved timestep size controller is introduced. The new model is tested on problems containing Rayleigh-Taylor or Richtmyer-Meshkov mixing layers, and is able to reproduce the behavior of well resolved BHR4 simulations with reasonable accuracy.

97 MATHEMATICS AND COMPUTING↗

High performance etchant for thinning p(+)-InP and its application to p(+)n InP solar cell fabrication

An etchant, namely (o-H3PO4)u: (HNO3)v: (H2O2)t: (H2O)1-(u+v+t) is developed for thinning, after contacting, the p(+) emitter layer of p(+)n InP structures made by thermal diffusion. Varying u, v, and t, reproducible etch rates of 5 to 110 nm/min are obtained. After thinning the 0.6- to 2.5-micron thick p(+) InP layer down to 60-250 nm, specular surfaces are obtained at up to 80 nm/min etch rate. Due to its intrinsic qualities the resisual P-rich oxide after thinning the emitter layer provides surface passivation of p(+) InP surfaces and can also serve as a first-layer AR coating.

Faur, Maria↗

InP solar cell with window layer

The invention features a thin light transmissive layer of the ternary semiconductor indium aluminum arsenide (InAlAs) as a front surface passivation or 'window' layer for p-on-n InP solar cells. The window layers of the invention effectively reduce front surface recombination of the object semiconductors thereby increasing the efficiency of the cells.

Jain, Raj K.↗

Surface passivation of Fe{sub 3}O{sub 4} nanoparticles with Al{sub 2}O{sub 3} via atomic layer deposition in a rotating fluidized bed reactor

Iron(II,III) oxide (Fe{sub 3}O{sub 4}) nanoparticles have shown great promise in many magnetic-related applications such as magnetic resonance imaging, hyperthermia treatment, and targeted drug delivery. Nevertheless, these nanoparticles are vulnerable to oxidation and magnetization loss under ambient conditions, and passivation is usually required for practical applications. In this work, a home-built rotating fluidized bed (RFB) atomic layer deposition (ALD) reactor was employed to form dense and uniform nanoscale Al{sub 2}O{sub 3} passivation layers on Fe{sub 3}O{sub 4} nanoparticles. The RFB reactor facilitated the precursor diffusion in the particle bed and intensified the dynamic dismantling of soft agglomerates, exposing every surface reactive site to precursor gases. With the aid of in situ mass spectroscopy, it was found that a thicker fluidization bed formed by larger amount of particles increased the residence time of precursors. The prolonged residence time allowed more thorough interactions between the particle surfaces and the precursor gas, resulting in an improvement of the precursor utilization from 78% to nearly 100%, even under a high precursor feeding rate. Uniform passivation layers around the magnetic cores were demonstrated by both transmission electron microscopy and the statistical analysis of Al mass concentrations. Individual particles were coated instead of the soft agglomerates, as was validated by the specific surface area analysis and particle size distribution. The results of thermogravimetric analysis suggested that 5 nm-thick ultrathin Al{sub 2}O{sub 3} coatings could effectively protect the Fe{sub 3}O{sub 4} nanoparticles from oxidation. The x-ray diffraction patterns also showed that the magnetic core crystallinity of such passivated nanoparticles could be well preserved under accelerated oxidation conditions. The precise thickness control via ALD maintained the saturation magnetization at 66.7 emu/g with a 5 nm-thick Al{sub 2}O{sub 3} passivation layer. This good preservation of the magnetic properties with superior oxidation resistance will be beneficial for practical magnetic-based applications.

36 MATERIALS SCIENCE↗

Plasma-based edge terminations for gallium nitride power devices

A p-n diode includes a first electrode, a n-GaN layer on the first electrode, a p-GaN layer on the n-GaN layer, and a second electrode on a first portion of the p-GaN layer. A region of the p-GaN layer surrounding the electrode is a passivated region. Treating a GaN power device having a p-GaN layer includes covering a portion of the p-GaN layer with a metal layer, exposing the p-GaN layer to a hydrogen plasma, and thermally annealing the p-GaN layer, thereby passivating a region of the p-GaN layer proximate the metal layer.

Zhao, Yuji↗

Electronic passivation of silicon surfaces by thin films of atomic layer deposited gallium oxide

This paper proposes the application of gallium oxide (Ga{sub 2}O{sub 3}) thin films to crystalline silicon solar cells. Effective passivation of n- and p-type crystalline silicon surfaces has been achieved by the application of very thin Ga{sub 2}O{sub 3} films prepared by atomic layer deposition using trimethylgallium (TMGa) and ozone (O{sub 3}) as the reactants. Surface recombination velocities as low as 6.1 cm/s have been recorded with films less than 4.5 nm thick. A range of deposition parameters has been explored, with growth rates of approximately 0.2 Å/cycle providing optimum passivation. The thermal activation energy for passivation of the Si-Ga{sub 2}O{sub 3} interface has been found to be approximately 0.5 eV. Depassivation of the interface was observed for prolonged annealing at increased temperatures. The activation energy for depassivation was measured to be 1.9 eV.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

In Situ Back‐Contact Passivation Improves Photovoltage and Fill Factor in Perovskite Solar Cells

Abstract Organic–inorganic hybrid perovskite solar cells (PSCs) have seen a rapid rise in power conversion efficiencies in recent years; however, they still suffer from interfacial recombination and charge extraction losses at interfaces between the perovskite absorber and the charge–transport layers. Here, in situ back‐contact passivation (BCP) that reduces interfacial and extraction losses between the perovskite absorber and the hole transport layer (HTL) is reported. A thin layer of nondoped semiconducting polymer at the perovskite/HTL interface is introduced and it is shown that the use of the semiconductor polymer permits—in contrast with previously studied insulator‐based passivants—the use of a relatively thick passivating layer. It is shown that a flat‐band alignment between the perovskite and polymer passivation layers achieves a high photovoltage and fill factor: the resultant BCP enables a photovoltage of 1.15 V and a fill factor of 83% in 1.53 eV bandgap PSCs, leading to an efficiency of 21.6% in planar solar cells.

Tan, Furui↗

Passivation Of High-Temperature Superconductors

Surfaces of high-temperature superconductors passivated with native iodides, sulfides, or sulfates formed by chemical treatments after superconductors grown. Passivating compounds nearly insoluble in and unreactive with water and protect underlying superconductors from effects of moisture. Layers of cuprous iodide and of barium sulfate grown. Other candidate passivating surface films: iodides and sulfides of bismuth, strontium, and thallium. Other proposed techniques for formation of passivating layers include deposition and gas-phase reaction.

Vasquez, Richard P.↗

A quantitative figure of merit for battery SEI films and their use as functional solid-state electrolytes

As a key passivation film that governs battery operation, the solid electrolyte interphase (SEI) has long been credited for enabling high-performance batteries or blamed for their eventual death. However, qualitative descriptions of the SEI often found in the literature (e.g., “conductive,” “passivating”) highlight our incomplete understanding of this layer, where even the most basic properties foundational to SEI function remain difficult to measure. Here, we quantify SEI conductivities and SEI transference numbers using a separator-free Cu|SEI|Li architecture that treats the SEI as a functional solid-state electrolyte (SSE). We find that while any SEI property alone (e.g., electronic conductivity) is weakly correlated (R 2 < 0.67) with battery performance (e.g., Coulombic efficiency), a strong correlation (R 2 > 0.99) can be achieved by defining the “SEI cT number” as a product between the SEI transference number (T) and the ratio of SEI conductivities (c). Analogous to the thermoelectric figure of merit (i.e., zT ), SEI cT quantitatively benchmarks the holistic impact of SEI properties on battery performance and underscores the pitfalls of citing such properties in isolation. Perhaps most strikingly, we demonstrate that Li metal deposition and stripping at room temperature is possible in our separator-free Cu|SEI|Li cell, confirming that the SEI can function precisely as an SSE. Together, these results enrich our understanding of the SEI, not just as a passivation layer but as a functional structure that can potentially have important implications for solid-state batteries.

Science & Technology - Other Topics↗

Novel Process for Screen-Printed Selective Area Front Polysilicon Contacts for TOPCon Cells Using Laser Oxidation

The efficiency potential of double-side tunnel oxide passivated contact (DS-TOPCon) solar cells is limited by parasitic absorption in the front poly-Si layer, despite excellent passivation and high V OC . The use of patterned poly-Si only under the front metal grid lines can significantly reduce the parasitic absorption loss without sacrificing voltage. In this work, we demonstrate a simple, manufacturing-friendly method of patterning the front poly-Si using a nanosecond UV (355 nm) laser. We found that with laser powers ≥3 W at a 400 mm/s scan speed, an estimated 1–4 nm thick stoichiometric SiO 2 layer was grown on TOPCon. This served as a mask for KOH-etching of 200 nm poly-Si, allowing for patterning of poly-Si fingers required for selective TOPCon. While laser powers above 3 W caused substantial deterioration in passivation quality, the resulting damage in J 0 was largely recovered by subsequent PECVD SiN x deposition. At 3 W, the full area J 0 was found to be 36.8 fA·cm –2 . Furthermore, this translates to 1.68 fA·cm –2 for 4.48% coverage from the wing area of the polyfinger lines (100 lines–100 μm wide and 30 μm metal) contributing to a total front J 0 of ~10 fA·cm –2 , well suited for 25% efficient solar cells

42 ENGINEERING↗

A passive model for the evolution of subgrid-scale instabilities in turbulent flow regimes

In this work, a zero-dimensional model for the development of turbulent mixing layers driven by Rayleigh–Taylor (RT) or Richtmyer–Meshkov (RM) instabilities is presented, for application in Reynolds-Averaged Navier–Stokes (RANS) simulations. The model approximates the behavior of the turbulent mixing layer at a passively advected tracer particle that sits on the material interface of interest in the simulation, and is used to provide initial conditions for the RANS model once the mixing layer width has developed to a size that may be resolved on the computational mesh. The model relies on approximations to the Besnard–Harlow–Rauenzahn (BHR) RANS closure equations and is thus consistent the turbulent development of the mixing layer, unlike previous models of this type which have focused on the early-time laminar development of RT or RM instabilities. These instabilities will often grow through an initially laminar state before developing into turbulence, and criteria for switching from an existing laminar model to the proposed turbulent model are considered. The proposed model reproduces the mixing layer development of RT and RM instabilities seen in mixed width resolving BHR RANS simulations to a reasonable degree of accuracy, and relaxes the need for the RANS simulation to resolve the mixed width as soon as the mixing layer becomes turbulent, which may be impractical in cases where the mixing layer grows through a wide range of scales.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Passive microwave remote sensing of an anisotropic random-medium layer

The principle of reciprocity is invoked to calculate the brightness temperatures for passive microwave remote sensing of a two-layer anisotropic random medium. The bistatic scattering coefficients are first computed with the Born approximation and then integrated over the upper hemisphere to be subtracted from unity, in order to obtain the emissivity for the random-medium layer. The theoretical results are illustrated by plotting the emissivities as functions of viewing angles and polarizations. They are used to interpret remote sgnsing data obtained from vegetation canopy where the anisotropic random-medium model applies. Field measurements with corn stalks arranged in various configurations with preferred azimuthal directions are successfully interpreted with this model.

Lee, J. K.↗

Quantum cascade laser with monolithically integrated passive waveguide

A photonic integrated circuit device includes a passive waveguide section formed over a substrate, a quantum cascade laser (QCL) gain section formed over the substrate and adjacent to the passive waveguide section, and a taper section disposed between and in contact with each of the passive waveguide section and the QCL gain section. In some embodiments, the passive waveguide section includes a passive waveguide core layer disposed between a first cladding layer and a second cladding layer. In some examples, the QCL gain section includes a QCL active region disposed between a first confinement layer and a second confinement layer, where the QCL active region has a lower index of refraction than each of the first and second confinement layers. In some embodiments, the taper section is configured to optically couple the QCL gain section to the passive waveguide section.

Jung, Seungyong↗