Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oxygen defects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Spectroscopic Investigation of Shallow Hole Traps in Ga- and B-doped Czochralski Silicon: Insight into Light-Induced Degradation

We report the minority carrier lifetime in B-doped Czochralski (Cz) Si declines upon carrier injection due to light-induced degradation (LID), which is attributed to the formation of a recombination-active boron-oxygen complex. Ga-doped Cz Si does not undergo LID. Previously, we showed that B-doped Cz Si undergoes a transition from paramagnetic to diamagnetic due to LID. Herein, we show that Ga-doped Cz Si remains paramagnetic upon carrier injection. This suggests that either the shallow hole traps that are formed in B-doped Cz Si are absent in Ga-doped Cz Si, or the negative-U centers in Ga-doped Cz Si do not transform into a recombination-active configuration, because the shallow acceptor trap state is shallower than the Ga acceptor level in the forbidden gap. In contrast to B-doped Cz Si, the defect signatures in Ga-doped Cz Si do not change upon light exposure, as detected by both electron paramagnetic resonance and deep-level transient spectroscopy.

14 SOLAR ENERGY↗
DOE OSTI2025

Symmetry-mediated quantum coherence of W 5+ spins in an oxygen-deficient double perovskite

Elucidating the factors limiting quantum coherence in real materials is essential to the development of quantum technologies. Here we report a strategic approach to determine the effect of lattice dynamics on spin coherence lifetimes using oxygen deficient double perovskites as host materials. In addition to obtaining millisecond T 1 spin-lattice lifetimes at T ~ 10 K, measurable quantum superpositions were observed up to room temperature. We determine that T 2 enhancement in Sr 2 CaWO 6-δ over previously studied Ba 2 CaWO 6-δ is caused by a dynamically-driven increase in effective site symmetry around the dominant paramagnetic site, assigned as W 5+ via electron paramagnetic resonance spectroscopy. Further, a combination of experimental and computational techniques enabled quantification of the relative strength of spin-phonon coupling of each phonon mode. This analysis demonstrates the effect of thermodynamics and site symmetry on the spin lifetimes of W 5+ paramagnetic defects, an important step in the process of reducing decoherence to produce longer-lived qubits.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Unveiling the influence of selective-area-regrowth interfaces on local electronic properties of GaN p-n junctions for efficient power devices

Here, we report correlated nanoscale mapping of the structure, composition, and properties of regrown GaN p-n junctions to identify how etching and non-planar regrowth processes limit diode performance via the introduction of unintentional dopants and defect states. p-GaN was selectively regrown in n-GaN trenches with SiO 2 masks of variable mask-to-trench-width ratio. Dilute Al layers were periodically introduced during regrowth as markers of the growth interface. Correlated nanoscale mapping of doping, conductivity, and dopant complexes was achieved with atom probe tomography (APT), scanning spreading resistance microscopy (SSRM), and cathodoluminescence (CL) spectroscopy, respectively. The Al marker layers, detected by APT, enabled reconstruction of the faceted growth interface and correlation of the dopant concentration with position and time. The p-GaN growth rate is proportional to the mask-to-trench width ratio while the dopant incorporation rate is invariant. At trench edges, magnesium incorporation is suppressed, and oxygen incorporation enhanced, due to preferential incorporation on the semi-polar growth surface, leading to compensation and less abrupt p-n junctions; the SiO 2 mask is a source of oxygen. Residual etch damage below the regrowth interface induces n-type and p-type conductivity, creating leakage pathways. The non-uniform Mg incorporation is driven by crystal anisotropy and is thus inherent to non-planar regrowth, but can be mitigated by engineering the regrowth interface and process parameters. The unprecedented integration of spatially resolved mapping of dopants, impurities, conductivity, and carrier type is a powerful approach to discriminating distinct factors that limit the performance of regrown diodes, enabling the rational optimization of process and device design.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The causal relationship between melt pool geometry and energy absorption measured in real time during laser-based manufacturing

During laser powder bed fusion additive manufacturing, laser power absorption is governed by a pro -tean pool of molten metal that can present as a highly reflective surface, a deeply absorbing cavity, or some amalgamation thereof. These melt pool dynamics have been linked to defect creation, porosity, and surface finish quality. Although these are therefore critical for determining final part quality, their in-stantaneous influence on laser absorption have only been explored through simulation. To date, direct real-time observations have been elusive due to the locally extreme environment. In this work, we fo-cus a laser on Ti-6Al-4V powder and bare plate while quantifying the time-dependent, absolute energy absorption by monitoring omnidirectional backscattered laser intensity. We also simultaneously record the projective melt pool geometries with high-speed synchrotron x-ray imaging. We find that laser ab-sorption strongly reflects the stability of the vapor depression over a wide range of applied laser powers, oxygen content in the processing atmosphere, and with the presence of powder. During laser scanning of a powder bed surface, we find a significant absorption reduction after 400 mu s due to a dramatic change in the vapor depression aspect ratio-an event known to create porosity. Furthermore, as several industrial scan strate-gies necessitate thousands of these events during a build, their identification and control is of significant practical importance. Lastly, a normalized enthalpy model is demonstrated to be effective in quantifying the relationship between the laser absorption and cavity depth, even under transient conditions. In addi-tion to providing vital quantitative data for simulation calibration, the correlation of melt pool geometry with laser absorption during realistic processing conditions suggests the use of a total backscattered light detection system for real-time process control.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Pt Atomic Single-Layer Catalyst Embedded in Defect-Enriched Ceria for Efficient CO Oxidation

The local coordination structure of metal sites essentially determines the performance of supported metal catalysts. Here, using a surface defect enrichment strategy, we successfully fabricated Pt atomic single-layer (Pt ASL ) structures with 100% metal dispersion and precisely controlled local coordination environment (embedded vs adsorbed) derived from Pt single-atoms (Pt 1 ) on ceria-alumina supports. The local coordination environment of Pt 1 not only governs its catalytic activity but also determines the Pt 1 structure evolution upon reduction activation. For CO oxidation, the highest turnover frequency can be achieved on the embedded Pt ASL in the CeO 2 lattice, which is 3.5 times of that on the adsorbed Pt ASL on the CeO 2 surface and 10–70 times of that on Pt1. The favorable CO adsorption on embedded Pt ASL and improved activation/reactivity of lattice oxygen within CeO 2 effectively facilitate the CO oxidation. This work provides new insights for the precise control of the local coordination structure of active metal sites for achieving 100% atomic utilization efficiency and optimal intrinsic catalytic activity for targeted reactions simultaneously.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The core autophagy machinery is not required for chloroplast singlet oxygen-mediated cell death in the Arabidopsis thaliana plastid ferrochelatase two mutant

Chloroplasts respond to stress and changes in the environment by producing reactive oxygen species (ROS) that have specific signaling abilities. The ROS singlet oxygen ( 1 O 2 ) is unique in that it can signal to initiate cellular degradation including the selective degradation of damaged chloroplasts. This chloroplast quality control pathway can be monitored in the Arabidopsis thaliana mutant plastid ferrochelatase two ( fc2 ) that conditionally accumulates chloroplast 1 O 2 under diurnal light cycling conditions leading to rapid chloroplast degradation and eventual cell death. The cellular machinery involved in such degradation, however, remains unknown. Recently, it was demonstrated that whole damaged chloroplasts can be transported to the central vacuole via a process requiring autophagosomes and core components of the autophagy machinery. The relationship between this process, referred to as chlorophagy, and the degradation of 1 O 2 -stressed chloroplasts and cells has remained unexplored. Results To further understand 1 O 2 -induced cellular degradation and determine what role autophagy may play, the expression of autophagy-related genes was monitored in 1 O 2 -stressed fc2 seedlings and found to be induced. Although autophagosomes were present in fc2 cells, they did not associate with chloroplasts during 1 O 2 stress. Mutations affecting the core autophagy machinery ( atg5 , atg7 , and atg10 ) were unable to suppress 1 O 2 -induced cell death or chloroplast protrusion into the central vacuole, suggesting autophagosome formation is dispensable for such 1 O 2 –mediated cellular degradation. However, both atg5 and atg7 led to specific defects in chloroplast ultrastructure and photosynthetic efficiencies, suggesting core autophagy machinery is involved in protecting chloroplasts from photo-oxidative damage. Finally, genes predicted to be involved in microautophagy were shown to be induced in stressed fc2 seedlings, indicating a possible role for an alternate form of autophagy in the dismantling of 1 O 2 -damaged chloroplasts. Conclusions Our results support the hypothesis that 1 O 2 -dependent cell death is independent from autophagosome formation, canonical autophagy, and chlorophagy. Furthermore, autophagosome-independent microautophagy may be involved in degrading 1 O 2 -damaged chloroplasts. At the same time, canonical autophagy may still play a role in protecting chloroplasts from 1 O 2 -induced photo-oxidative stress. Together, this suggests chloroplast function and degradation is a complex process utilizing multiple autophagy and degradation machineries, possibly depending on the type of stress or damage incurred.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Hydrogen and water interactions with CrMnFeCoNi alloy from density functional theory calculations

High entropy alloys (HEAs) are a promising class of materials with remarkable mechanical and catalytic properties. Among these, the quinary CrMnFeCoNi alloy (also called “Cantor alloy”) has attracted considerable attention given its thermodynamic stability and remarkable mechanical properties under different temperatures. Given that various degradation mechanisms involve multiple contaminants, such as hydrogen and water in hydrogen embrittlement and surface poisoning, respectively, understanding their interactions with the Cantor alloy is critical for its practical applications as structural, nuclear, or hydrogen storage material. In this work, we perform first-principles calculations based on Density Functional Theory (DFT) to investigate such interactions when considering various microstructures, including bulk materials and those containing certain defects, such as grain boundaries, stacking faults, and vacancies. We also employ Global Sensitivity Analysis to identify the importance of different factors in the stability of the impurities. We find that the accuracy of the H formation energy is significantly affected by spin polarization and chemical short-range order. The study also identifies a strong tendency for hydrogen interstitials to segregate to Σ5(210)/[001] symmetric tilt grain boundary, even when H concentrations are high, suggesting that a certain type of grain boundaries acts as H sinks within the alloy. Further, this result is reinforced by the low formation energy of vacancy-hydrogen complexes, which can contain multiple hydrogen atoms. Finally, the surface reactivity analysis reveals that the adsorption energy of oxygen and hydroxyl groups is highly sensitive to the specific metal atom involved in the binding, with a clear preference for chromium atoms, which could have implications for the alloy’s oxidation and corrosion behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Combined Experimental and Theoretical Investigations of n-Type BiFeO 3 for Use as a Photoanode in a Photoelectrochemical Cell

Combined experimental and theoretical investigations were performed to evaluate the potential of n-type BiFeO 3 as a photoanode. While previous experimental and theoretical studies on BiFeO 3 mainly focused on its ferroelectric properties, several studies have reported the advantages of BiFeO 3 as a photoelectrode for solar water splitting (e.g. bandgap energy and band edge positions relative to water reduction and oxidation potentials). However, the photoelectrochemical properties of n-type BiFeO 3 have not yet been thoroughly investigated. In our experimental investigation, we developed an electrodeposition-based synthesis to prepare uniform n-type BiFeO 3 thin-film electrodes. Furthermore, using a heat treatment under a N 2 environment, we intentionally introduced additional oxygen vacancies into the pristine n-type BiFeO 3 electrodes to increase the majority carrier density. The bandgaps, flatband potentials, photocurrent onset potentials, photocurrent generation, and photoelectrochemical stabilities of the pristine and N 2 -treated BiFeO 3 photoanodes were investigated comparatively to improve our understanding of BiFeO 3 photoanodes and to examine the effect of oxygen vacancies on the photoelectrochemical properties of BiFeO 3 . In our theoretical investigation, we performed first-principles calculations and demonstrated the formation of a small polaron when an extra electron was introduced into the BiFeO 3 lattice. Changes in electronic states cause by the small polaron formation were carefully investigated. We also examined the effects of oxygen vacancies on electron polaron formation and carrier concentration in BiFeO 3 . Using charge formation energy calculations and referencing charge transition levels to the free electron polaron level instead of to the conduction band minimum, we showed that the oxygen vacancy is capable of serving as a donor to enhance the carrier concentration of BiFeO 3 . Furthermore, our theoretical results agree well with our experimental findings. Together, the new experimental and theoretical results and discussion provided in this study have considerably improved our understanding of n-type BiFeO 3 as a photoanode.

25 ENERGY STORAGE↗
DOE OSTI2023

Recent Developments in Revealing the Impact of Complex Metal Oxide Reconstruction on Catalysis

Surface reconstruction of complex metal oxides refers to the alterations of the topmost catalyst surface, relative to the bulk structure, following exposure to pretreatment or reaction conditions during heterogeneous catalysis. (1) This structural and electronic transformation may involve (1) changes of the exposed crystallographic facets, (2) changes in chemical composition, such as the enrichment of specific elements, and, (3) morphological variations, including surface roughness and defects (Scheme 1). Beyond relaxation, surface reconstruction here also encompasses disruptions to the periodicity of the sublayers and changes to its stoichiometry. This change significantly influences the chemical properties of the catalyst surface, such as redox sites, (2) acid/base pairs, hydroxyl groups, (3) and surface defects. Surface reconstruction occurs due to the thermodynamic drive to lower the surface energy of the catalyst under the surrounding environment (e.g., temperature, chemical potential of species present). In addition to the treatment or reaction conditions, the extent of reconstruction also depends on the elements in the metal oxide structure. For instance, annealing ABO 3 perovskites (SrTiO 3 , BaTiO 3 , and BaZrO 3 ) at high temperatures (500 °C) in O 2 has a very different impact on the A/B ratio at the surface (ranging from 0.9 to 2.5), depending on the identity of A and B. (4) Metal oxide surface reconstruction under an electric field and exposure to acidic and alkaline media has recently gained increased attention in electrocatalysis, such as in the oxygen evolution reaction (OER); (5,6) however, in this Viewpoint we focus on the impact of surface reconstruction on thermal catalysis, a critical enduring research theme with ongoing challenges. Here, we start showcasing approaches to characterize surface reconstruction at the topmost surface layer, such as low-energy ion scattering (LEIS), discussing advantages and limitations. Next, we connect characterization of surface reconstruction to site-specific kinetic analysis, enabled via steady-state isotopic transient kinetic analysis (SSITKA), and we express our viewpoint on building structure–performance relationships by deeply understanding reconstructed surfaces. Later, we comment on the potential of tuning surface reconstruction to enhance catalytic performance. Finally, we explore the interplay between surface reconstruction and the “intelligent behavior”.

alcohol conversion↗
DOE OSTI2019

Evolution Pathway from Iron Compunds to Fe 1 (II)-N 4 Sites through Gas-Phase Iron during Pyrolysis

Pyrolysis is indispensable for synthesizing highly active Fe–N–C catalysts for the oxygen reduction reaction (ORR) in acid, but how Fe, N, and C precursors transform to ORR-active sites during pyrolysis remains unclear. This knowledge gap obscures the connections between the input precursors and the output products, clouding the pathway toward Fe–N–C catalyst improvement. Here, we unravel the evolution pathway of precursors to ORR-active catalyst comprised exclusively of single-atom Fe 1 (II)–N 4 sites via in-temperature X-ray absorption spectroscopy. The Fe precursor transforms to Fe oxides below 300 °C and then to tetrahedral Fe 1 (II)–O 4 via a crystal-to-melt-like transformation below 600 °C. The Fe 1 (II)–O 4 releases a single Fe atom that diffuses into the N-doped carbon defect forming Fe 1 (II)–N 4 above 600 °C. This vapor-phase single Fe atom transport mechanism is verified by synthesizing Fe 1 (II)–N 4 sites via “noncontact pyrolysis” wherein the Fe precursor is not in physical contact with the N and C precursors during pyrolysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

The role of water vapor during the synthesis of hydrogen doped In 2 O 3

Hydrogen-doped In 2 O 3 synthesized using magnetron sputtering or atomic layer deposition in the presence of water vapor has high transparency in the near infra-red region and mobility values that are almost three to four times of those in commercially used In 2 O 3 :Sn at a much lower carrier concentration. However, simple questions like what happens when water molecules enter In 2 O 3 or why the dominant charge carrier changes from an oxygen vacancy in In 2 O 3 :Sn to H + in In 2 O 3 are not clear. Using hybrid functional based density functional theory calculations, in this study we show that water molecules spontaneously split into H + and OH – . The H + interstitial bonds with an oxygen in In 2 O 3 , and the OH – interstitial occupies a vacant lattice site or is trapped by an oxygen vacancy. Thus, in agreement with experimental findings, our results suggest that the concentration of oxygen vacancies decreases as the partial pressure of water increases. The charge transition level, ϵ ( – / + ) , of a hydrogen interstitial and the Fermi level at which the formation energies of OH – and H + are equal lie above the conduction band minimum, suggesting that the H + interstitial has a lower formation energy. In addition, water molecules do not exhibit any propensity to form clusters, meaning that H + ions can diffuse and remain spatially separated from each other.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Engineering of niobium surfaces through accelerated neutral atom beam technology for quantum applications

A major roadblock to scalable quantum computing is phase decoherence and energy relaxation caused by qubits interacting with defect-related two-level systems (TLSs). Native oxides present on the surfaces of superconducting metals used in quantum devices are acknowledged to be a source of TLS that decrease qubit coherence times. Reducing microwave loss by “surface engineering” (i.e., replacing the uncontrolled native oxide of superconducting metals with a thin, stable surface with predictable characteristics) can be a key enabler for pushing performance forward with devices of higher intrinsic quality factor. In this work, we present a novel approach to replace the native oxide of niobium (typically formed in an uncontrolled fashion when its pristine surface is exposed to air) with an engineered oxide, using a room-temperature process that leverages accelerated neutral atom beam (ANAB) technology at 300 mm wafer scale. This ANAB is composed of a mixture of argon and oxygen, with tunable energy per atom, which is rastered across the wafer surface. The ANAB-engineered Nb-oxide thickness was found to vary from 2 to 6 nm depending on ANAB process parameters. The modeling of variable-energy x-ray photoelectron spectroscopy data confirms the thickness and compositional control of Nb surface oxide by the ANAB process. Furthermore, these results correlate well with those from transmission electron microscopy and x-ray reflectometry. Since ANAB is broadly applicable to material surfaces, the present study indicates its promise for modification of the surfaces of superconducting quantum circuits to achieve longer coherence times.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Design Principles for Efficient and Stable Water Splitting Photoelectrocatalysts

Photoelectrochemical water splitting is a promising avenue for sustainable production of hydrogen used in the chemical industry and hydrogen fuel cells. The basic components of most photoelectrochemical water splitting systems are semiconductor light absorbers coupled to electrocatalysts, which perform the desired chemical reactions. A critical challenge for the design of these systems is the lack of stability for the majority of desired semiconductors under operating water splitting conditions. One strategy to address this issue is to protect the semiconductor by covering it with a stabilizing insulator layer, creating a metal–insulator–semiconductor (MIS) architecture, which has demonstrated improved stability. In addition to enhanced stability, the insulator layer may significantly affect the electron and hole transfer, which governs the recombination rates. Furthermore, the insertion of an insulator layer leads to the introduction of additional insulator/electrocatalyst and insulator/semiconductor interfaces. These interfaces can impact the system’s performance significantly, and they need to be carefully engineered to optimize the efficiencies of MIS systems. In this Account, we describe our recent progress in shedding light on the critical role of the insulator and the interfaces on the performance of MIS systems. We discuss our findings by focusing on the concrete example of planar n-type Si protected by a HfO 2 insulator layer and coupled to a Ni or Ir electrocatalyst that performs the oxygen evolution reaction, one of the water splitting half-reactions. To improve our fundamental understanding of the insulator layer, we precisely control the HfO 2 insulator thickness using atomic layer deposition (ALD), and we perform a series of rigorous electrochemical experiments coupled with theory and modeling. We demonstrate that by tuning the insulator thickness, we can control the flux and recombination of photogenerated electrons and holes to optimize the generated photovoltage. Despite optimizing the thickness, we find that the maximum generated photovoltage in MIS systems is often significantly lower than the upper performance limit, i.e., there are additional losses in the system that could not be addressed by optimizing the insulator thickness. We identify the sources of these losses and describe strategies to minimize them by a combination of improving the semiconductor light absorption, removing nonidealities associated with interfacial defects, and finding alternative insulators with improved charge carrier selectivity. Finally, we quantify the improvements that can be obtained by implementing these specific strategies. Our collective work outlines strategies to analyze MIS systems, identify the sources of efficiency losses, and optimize the design to approach the fundamental performance limits. Furthermore, these general approaches are broadly applicable to photoelectrochemical materials that utilize sunlight to produce value-added chemicals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Time at Temperature Abstract and Intern Poster

Current NRC regulations for BWR operations dictate that any occurrence reaching the point of Departure from Nucleate Boiling (DNB) disqualifies the use of the fuel rod for further reactor operation. That criteria does not account for duration of rate of the power increase, the corresponding effects on material properties or rewetting that may occur. Previous Anticipated Operational Occurrences (AOOs) show short durations power increase that may require limited amounts of heat removal. Industrial experience has shown evidence that fuel can reach dryout yet continue to safely operate in regular reactor conditions. The gap in research into such occurrences is the motivation for a series of experiments, including this current work. Time-at-Temperature experiments aim to identify and characterize the microstructural changes in Zircaloy-2 under oxygen-free high temperatures. This work uses the FlashDSC instrument to rapidly ramp up and down the temperature of a focus ion beam (FIB) prepared large area lift-out (LALO) of Zircaloy-2 at a rate of 10,000 K/s to desired values. The focus is to characterize the microstructure evolution, if any, of Zircaloy-2 that may impact its performance under typical BWR conditions. This characterization includes analyzing grain structure and size, secondary phase particle (SPPs) size, shape, composition, and location using Transmission Electron Microscopy (TEM). Further data collection and analysis is in progress including diffraction pattern indexing and 4D STEM processing. While current results focus on the testing and characterizing unirradiated material, future plans include expansion to irradiated material to explore the effects of rapid transition rates seen in DNB and dryout conditions on irradiationg damage and defect annealing.

36 - MATERIALS SCIENCE↗
DOE OSTI2020

Phase equilibrium of liquid water and hexagonal ice from enhanced sampling molecular dynamics simulations

We study the phase equilibrium between liquid water and ice Ih modeled by the TIP4P/Ice interatomic potential using enhanced sampling molecular dynamics simulations. Our approach is based on the calculation of ice Ih-liquid free energy differences from simulations that visit reversibly both phases. The reversible interconversion is achieved by introducing a static bias potential as a function of an order parameter. The order parameter was tailored to crystallize the hexagonal diamond structure of oxygen in ice Ih. Furthermore, we analyze the effect of the system size on the ice Ih-liquid free energy differences, and we obtain a melting temperature of 270 K in the thermodynamic limit. This result is in agreement with estimates from thermodynamic integration (272 K) and coexistence simulations (270 K). Since the order parameter does not include information about the coordinates of the protons, the spontaneously formed solid configurations contain proton disorder as expected for ice Ih.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Direct Mechanochemical Synthesis, Phase Stability, and Electrochemical Performance of α-NaFeO 2

To better understand polymorph control in transition metal oxides, the mechanochemical synthesis of NaFeO 2 was explored. In this paper, we report the direct synthesis of α-NaFeO 2 through a mechanochemical process. By milling Na 2 O 2 and γ-Fe 2 O 3 for 5 h, α-NaFeO 2 was prepared without high-temperature annealing needed in other synthesis methods. While investigating the mechanochemical synthesis, it was observed that changing the starting precursors and mass of precursors affects the resulting NaFeO 2 structure. Density functional theory calculations on the phase stability of NaFeO 2 phases show that the α phase is stabilized over the β phase in oxidizing environments, which is provided by the oxygen-rich reaction between Na 2 O 2 and Fe 2 O 3 . This provides a possible route to understanding polymorph control in NaFeO 2 . Annealing the as-milled α-NaFeO 2 at 700 °C has resulted in increased crystallinity and structural changes that improved electrochemical performance in terms of capacity over the as-milled sample.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Epitaxially Grown Single-Crystalline SrTiO 3 Membranes Using a Solution-Processed, Amorphous SrCa 2 Al 2 O 6 Sacrificial Layer

Water-soluble sacrificial layers based on epitaxially-grown, single crystalline (Ca, Sr, Ba) 3 Al 2 O 6 layer are widely used for creating free-standing perovskite oxide membranes. However, obtaining these sacrificial layers with intricate stoichiometry remains a challenge, especially for molecular beam epitaxy (MBE). In this study, we demonstrate the hybrid MBE growth of epitaxial, single crystalline SrTiO 3 films using a solution processed, amorphous SrCa 2 Al 2 O 6 sacrificial layer onto SrTiO 3 (001) substrates. Prior to the growth, the oxygen plasma exposure was used to first create the crystalline SrCa 2 Al 2 O 6 layer with well-defined surface crystallinity. Utilizing reflection high energy electron diffraction, x-ray diffraction, and atomic force microscopy, we observe an atomic layer-by-layer growth of epitaxial, single crystalline SrTiO 3 film on the SrCa 2 Al 2 O 6 layer with atomically smooth surfaces. The SrCa 2 Al 2 O6 layer was subsequently dissolved in de-ionized water to create free-standing SrTiO3 membranes that were transferred onto a metal-coated Si wafer. Membranes created with Sr-deficiency revealed ferroelectric-like behavior measured using piezo force microscopy whereas stoichiometric films remained paraelectric-like. Furthermore, these findings underscore the viability of using ex-situ deposited amorphous SrCa2Al2O6 for epitaxial, single crystalline growth, as well as the importance of point defects in determining the ferroic properties in membranes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗