Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oxidative stress”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

NiAl-Base Composite Containing High Volume Fraction of AIN Particulate for Advanced Engines

Cryomilling of prealloyed NiAl containing 53 at. % AJ was carried out to achieve high nitrogen levels. The consolidation of cryomilled powder by extrusion or hot pressing/ hot isostatic pressing resulted in a fully dense NiAl-base composite containing 30 vol. % of inhomogeneously distributed, nanosized AIN particulate. The NiAl-30AIN composite exhibited the highest compression yield strengths at all temperatures between 300 and 1300 K as compared with other compositions of NiAl-AIN composite. The NiAl-30AIN specimens tested under compressive creep loading between 1300 and 1500 K also exhibited the highest creep resistance with very little surface oxidation indicating also their superior elevated temperature oxidation resistance. In the high stress exponent regime, the strength is proportional to the square root of the AIN content and in the low stress exponent regime, the influence of AIN content on strength appears to be less dramatic. The specific creep strength of this material at 1300 K is superior to a first generation Ni-base single crystal superalloy. The improvements in elevated temperature creep strength and oxidation resistance have been achieved without sacrificing the room temperature fracture toughness of the NiAl-base material. Based on its attractive combination of properties, the NiAl-30AIN composite is a potential candidate for advanced engine applications,

Hebsur, Mohan G.↗
NASA NTRS1971

Thermomechanical and Thermochemical Behavior of a Hafnium-20 Percent Tantalum Alloy

An investigation was conducted to determine the thermomechanical and thermochemical behavior of a high temperature, oxidation resistant, hafnium-20 percent tantalum alloy. The elastic and shear moduli of this alloy were determined in air up to 1000 C and in vacuum up to 2000 C using a mechanical resonance technique. The internal friction of the alloy was measured up to temperatures greater than 1400 C. Room temperature stress-strain behavior of the oxidized and unoxidized alloy was established. The effect of annealing on the elastic and shear moduli of the extruded rod material was investigated. The martensitic-type phase transformation occurring in the alloy was studied using hot stage metallography and electron microscopy. Static oxidation tests were conducted on the alloy at temperatures from 1000 C to 1700 C with weight gain measurements made as a function of time and temperatures. Surface morphology studies were conducted on the oxide coatings formed at the different temperatures using scanning electron microscopy and X-ray diffraction techniques.

Howell, J. P.↗
NASA NTRS1989

TEM studies of oxidized NiAl and Ni3Al cross sections

Cross sections of oxide scale/(Ni-Al) intermetallics were prepared by a new method and studied using primarily TEM. The cross sections were prepared by encasing an oxidized metal specimen sandwich in a low-melting-temperature zinc alloy. Observations of oxidized zirconium-doped beta-NiAl cross sections revealed crystallographic voids beneath an adherent Al2O3 scale. The oxide-metal interface was incoherent, but a high dislocation density in the metal near the interface suggested that a large tensile stress was induced by the attached oxide scale. A duplex Al2O3-NiAl2O4 scale formed on zirconium-doped and zirconium/boron-doped gamma-prime-Ni3Al alloys. Additional results are presented involving oxidation mechanisms and oxide-metal interface structures.

Doychak, J.↗
DOE OSTI2020

Improving stability of ALD ZrN thin film coatings over U-Mo dispersion fuel

Atomic layer deposition (ALD) of ZrN is a candidate technology for coating U-Mo dispersion fuel as a diffusion barrier coating. During the early development stages of the coating the ZrN deposition showed to be mechanically unstable and ultimately resulted in spalling. Based on experimental outcomes it was found that instabillity can be eliminated through the introduction of a thin amorphous (a) Al 2 O 3 interlayer coating deposited in between the ~1-μm thick ZrN and the U-Mo. substrate. To elucidate these findings simulations were performed with density functional theory (DFT) to measure work of adhesions at different interfaces while finite element modeling (FEM) was performed to measure the residual stress distribution. DFT indicated that the ZrN coating deposited over (a)-Al 2 O 3 is ~2.5 times stronger when compared to direct deposition over U or UO 2 substrate. While calculations from FEM recognized; (1) large stress concentrations can originate from the irregularly distributed native surface oxides (UO 2 ) over U-Mo and (2) stress concentrations can be reduced if those surface UO 2 can be modified to a uniform layer (achieved after application of a 8 nm (a)-Al 2 O 3 interlayer). These results provided explanations and confirmed the role played by interlayer in eliminating the original mechanical instability of the ZrN.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1988

Wear of liquid nitrogen-cooled 440C bearing steels in an oxygen environment

This paper presents up-to-date findings of the research being conducted to understand the mechanism of sliding wear in unlubricated 440C bearing steels under oxidative conditions. A sliding wear test rig has been designed and built with a cylinder-on-flat geometry. The equipment is capable of testing specimens under high axial loads and sliding speeds in a simulated LOX environment. Samples of 440C steel, quenched and tempered to a hardness of Rc 56, were tested under a load of 890 N and a sliding speed of 2.05 m/sec for total sliding distances of up to 5.54 km. Flash temperatures during these tests were measured with an IR camera and a fast digital recorder. Microstructural and microanalytical data from the worn surfaces and the debris particles are analyzed extensively, along with wear rates, flash temperatures, surface profiles, hardnesses, and residual stresses, in the context of oxidation and wear theories.

Chaudhuri, Dilip K.↗
DOE OSTI2020

Pitting behavior of friction stir repair-welded 304L stainless steel in 3.5% NaCl solution at room temperature: role of grain and defect structures

Stainless steel (SS) canisters used for storing spent nuclear waste are prone to chloride-induced stress corrosion cracking. Friction stir welding (FSW), being a low heat input process, can be used for repair welding of these canisters. In this study, an artificial crack was introduced on the 304L SS coupons by an electric discharge machining process. The artificial crack was repair-welded by FSW by maintaining the tool temperature a constant at two levels (725 and 825 °C). Friction stirring significantly reduced the grain size of the stirred zone (SZ) from about 47 to 2–4 μm. The fraction of low-angle grain boundaries increased in the SZ from 2 to 37–43%. Here, on the other hand, the fraction of special grain boundaries (Σ3 and Σ9) that was ~ 50% in the base metal reduced to < 10% in the SZ. During friction stirring, the oxide layer of artificial crack was broken and aligned to form a spiral defect called lazy-S structure. All these microstructural changes affected the corrosion behavior of the FSW specimens when tested in 3.5% NaCl at room temperature using cyclic polarization, chronoamperometry, and electrochemical impedance spectroscopy. The FSW specimens showed lower polarization resistance and lower transpassive potential than those of the base metal specimens. However, the pitting protection potentials of the FSW specimens were higher than that of the base metal. The pitting behavior of the FSW specimens was influenced more by the preferential attack on the lazy-S region than by passive film breakdown. The flat band potentials of the passive film formed on the FSW specimens were more positive than that of base metal. The charge carrier density of passive film formed on the FSW specimens was higher than that of the base metal. The higher fraction of low-angle grain boundaries present in the FSW specimens could supply more number of misorientation dislocations at the metal/film interface which could form anion vacancies by a climb process leading to formation of oxide at these locations without stressing the substrate. Therefore, low-angle boundaries are considered helpful for formation of stress-free passive films that will be highly stable and enhance both pitting and stress corrosion cracking resistance.

Dry storage canister↗
DOE OSTI2022

Subpicosecond Optical Stress Generation in Multiferroic BiFeO 3

We report optical excitation leads to ultrafast stress generation in the prototypical multiferroic BiFeO 3 . The time scales of stress generation are set by the dynamics of the population of excited electronic states and the coupling of the electronic configuration to the structure. X-ray free-electron laser diffraction reveals high-wavevector subpicosecond-time scale stress generation following ultraviolet excitation of a BiFeO 3 thin film. Stress generation includes a fast component with a 1/e rise time with an upper limit of 300 fs and longer-rise time components extending to 1.5 ps. The contributions of the fast and delayed components vary as a function of optical fluence, with a reduced a fast-component contribution at high fluence. The results provide insight into stress-generation mechanisms linked to the population of excited electrons and point to new directions in the application of nanoscale multiferroics and related ferroic complex oxides. The fast component of the stress indicates that structural parameters and properties of ferroelectric thin film materials can be optically modulated with 3 dB bandwidths of at least 0.5 THz.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
NASA NTRS1996

Use-dependent loss of active sympathetic neurogenic vasodilation after nitric oxide synthase inhibition in conscious rats. Evidence for the presence of preformed stores of nitric oxide-containing factors

In this study, we examined whether air-jet stress-induced active sympathetic hindlimb vasodilation in conscious rats involves the release of preformed stores of nitric oxide-containing factors. We determined the effects of repeated episodes of air-jet stress (six episodes given 5 minutes apart) on mean arterial pressure and vascular resistances in the mesenteric bed and intact and sympathetically denervated hindlimb beds of conscious rats treated with saline or the nitric oxide synthesis inhibitor N omega-nitro-L-arginine methyl ester (L-NAME, 25 mumol/kg IV). In saline-treated rats, air-jet stress produced alerting behavior, minor changes in blood pressure, pronounced mesenteric vaso-constriction, and immediate and marked vasodilation in the sympathetically intact hindlimb but a minor vasodilation in the sympathetically denervated hindlimb. Each air-jet stress produced virtually identical responses. In L-NAME-treated rats, the first air-jet stress produced vasodilator responses in the sympathetically intact and sympathetically denervated hindlimbs that were similar to those in the saline-treated rats. However, each subsequent air-jet stress produced progressively smaller vasodilator responses in the sympathetically intact but not the sympathetically denervated hindlimb. There was no loss of air-jet stress-induced alerting behavior or mesenteric vasoconstriction, suggesting that L-NAME did not interfere with the central processing of the air-jet or the resultant changes in autonomic nerve activity. The progressive diminution of air-jet stress-induced vasodilation in the intact hindlimb of L-NAME-treated rats may be due to the use-dependent depletion of preformed stores of nitric oxide-containing factors that cannot be replenished in the absence of nitric oxide synthesis.

NASA Discipline Regulatory Physiology↗
DOE OSTI2021

Preserved and variable spatial‐chemical changes of lipids across tomato leaves in response to central vein wounding reveals potential origin of linolenic acid in signal transduction cascade

Abstract Membrane lipids serve as substrates for the generation of numerous signaling lipids when plants are exposed to environmental stresses, and jasmonic acid, an oxidized product of 18‐carbon unsaturated fatty acids (e.g., linolenic acid), has been recognized as the essential signal in wound‐induced gene expression. Yet, the contribution of individual membrane lipids in linolenic acid generation is ill‐defined. In this work, we performed spatial lipidomic experiments to track lipid changes that occur locally at the sight of leaf injury to better understand the potential origin of linolenic and linoleic acids from individual membrane lipids. The central veins of tomato leaflets were crushed using surgical forceps, leaves were cryosectioned and analyzed by two orthogonal matrix‐assisted laser desorption/ionization mass spectrometry imaging platforms for insight into lipid spatial distribution. Significant changes in lipid composition are only observed 30 min after wounding, while after 60 min lipidome homeostasis has been re‐established. Phosphatidylcholines exhibit a variable pattern of spatial behavior in individual plants. Among lysolipids, lysophosphatidylcholines strongly co‐localize with the injured zone of wounded leaflets, while, for example, lysophosphatidylglycerol (LPG) (16:1) accumulated preferentially toward the apex in the injured zone of wounded leaflets. In contrast, two other LPGs (LPG [18:3] and LPG [18:2]) are depleted in the injured zone. Our high‐resolution co‐localization imaging analyses suggest that linolenic acids are predominantly released from PCs with 16_18 fatty acid composition along the entire leaf, while it seems that in the apex zone PG (16:1_18:3) significantly contributes to the linolenic acid pool. These results also indicate distinct localization and/or substrate preferences of phospholipase isoforms in leaf tissue.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1994

Effects of Thermal Cycling on Thermal Expansion and Mechanical Properties of Sic Fiber-reinforced Reaction-bonded Si3n4 Composites

Thermal expansion curves for SiC fiber-reinforced reaction-bonded Si3N4 matrix composites (SiC/RBSN) and unreinforced RBSN were measured from 25 to 1400 C in nitrogen and in oxygen. The effects of fiber/matrix bonding and cycling on the thermal expansion curves and room-temperature tensile properties of unidirectional composites were determined. The measured thermal expansion curves were compared with those predicted from composite theory. Predicted thermal expansion curves parallel to the fiber direction for both bonding cases were similar to that of the weakly bonded composites, but those normal to the fiber direction for both bonding cases resulted in no net dimensional changes at room temperature, and no loss in tensile properties from the as-fabricated condition. In contrast, thermal cycling in oxygen for both composites caused volume expansion primarily due to internal oxidation of RBSN. Cyclic oxidation affected the mechanical properties of the weakly bonded SiC/RBSN composites the most, resulting in loss of strain capability beyond matrix fracture and catastrophic, brittle fracture. Increased bonding between the SiC fiber and RBSN matrix due to oxidation of the carbon-rich fiber surface coating and an altered residual stress pattern in the composite due to internal oxidation of the matrix are the main reasons for the poor mechanical performance of these composites.

Bhatt, R. T.↗
NASA NTRS2003

Flow-dependent regulation of endothelial nitric oxide synthase: role of protein kinases

Vascular endothelial cells are directly and continuously exposed to fluid shear stress generated by blood flow. Shear stress regulates endothelial structure and function by controlling expression of mechanosensitive genes and production of vasoactive factors such as nitric oxide (NO). Though it is well known that shear stress stimulates NO production from endothelial nitric oxide synthase (eNOS), the underlying molecular mechanisms remain unclear and controversial. Shear-induced production of NO involves Ca2+/calmodulin-independent mechanisms, including phosphorylation of eNOS at several sites and its interaction with other proteins, including caveolin and heat shock protein-90. There have been conflicting results as to which protein kinases-protein kinase A, protein kinase B (Akt), other Ser/Thr protein kinases, or tyrosine kinases-are responsible for shear-dependent eNOS regulation. The functional significance of each phosphorylation site is still unclear. We have attempted to summarize the current status of understanding in shear-dependent eNOS regulation.

Non-NASA Center↗
DOE OSTI2024

Spectroscopic evaluation of tribologically-induced changes in surface chemistry of Zr-based bulk metallic glass

Bulk metallic glasses (BMGs) are promising structural materials owing to their high elastic limit and yield strength-to-weight ratio. While BMGs also exhibit attractive tribological properties (e.g., high wear resistance), the scientific basis for this behavior is not yet established. In particular, tribologically-induced changes in surface chemistry upon sliding are still an open topic of research. Here, we evaluated by X-ray photoelectron spectroscopy (XPS) the evolution of the surface chemistry of Vitreloy 105 (a Zr-rich BMG) upon sliding under different contact conditions against a tungsten carbide countersurface. The spectroscopic results indicate that the relative fraction of the metallic elements in the near-surface region is not affected by the sliding speed when the applied contact pressure is lower than 1.37 GPa, while a decrease in metallic zirconium was observed at lower sliding speeds and higher applied contact pressure (i.e., 1.71 GPa). Based on the spectroscopic results, a model is proposed for the effect of mechanical stress on the extent of oxidation of the near-surface region of Zr-based BMGs. In conclusion, the results of this work provide novel insights into the surface phenomena occurring on BMGs upon sliding and add significantly to our understanding of the tribological response of this class of promising structural materials.

Bulk metallic glasses↗
DOE OSTI2025

Tomographic assessment of peening for metallurgical bonding in cold spray

It is widely asserted that peening densifies cold spray coatings and improves particle–particle and particle–substrate bonding, yet systematic studies analyzing the evolution of bonding due to peening particle strikes are scarce. We explore peening at the level of individual particle impacts, by creating two-particle Cu-on-Cu stacks using laser-induced particle impact testing. Exploring impact velocities that range from the onset of bonding at the “critical velocity”, V cr , to its peak near 1.4⋅V cr , we perform full 3D tomography of the particle stacks to characterize the bonding state at the particle-substrate interface. Direct labeling of non-bonded patches and the total particle-substrate interface permits quantification and comparison of bonding in single impacts with bonding after subsequent impacts to reveal the origins of the peening effect. The data reveal a surprising finding: although a second impact directly atop the first particle increases the area of the particle-substrate interface (~40% area increase), there is no improvement in metallurgical bonding. Analysis of these data suggest that not only area expansion (and associated oxide rarefication), but also stress-induced extrusion of metal at that interface needs to occur to achieve metal-on-metal contact to see an enhancement in bonding. Furthermore, our analysis suggests that the subsequent impacting particle needs to have ~70% more kinetic energy to produce additional bonding; this implies that particle and velocity distributions within a spray may be helpful, and that peening may rely on unaligned impacts.

Bonding↗
DOE OSTI2020

Electrically Detected Magnetic Resonance Study of High-Field Stress Induced Si/SiO 2 Interface Defects.

It is widely accepted that the breakdown of Si0 2 gate dielectrics is caused by the buildup of stress-induced defects over time. Although several physical mechanisms have been proposed for the generation of these defects, very little direct experimental evidence as to the chemical and physical identity of these defects has been generated in the literature thus far. Here, we present electrically detected magnetic resonance (EDMR) measurements obtained via spin-dependent recombination currents at the interface of high-field stressed Si/Si0 2 metal-oxide-semiconductor field effect transistors (MOSFETs).

36 MATERIALS SCIENCE↗
NASA NTRS1984

The direct effects of strain on burning rates of composite solid propellants

A mathematical model is developed to predict burn rate augmentation due to strain in a composite solid propellant. The model assumes the effect is due to the ability of the flame to penetrate the small fissures and voids that form when a propellant is strained. The number and size of these fissures is obtained by applying a flaw propagation analysis to randomly distributed flaws that form when the binder-oxidizer particle bonds break under stress. A flame height is calculated with Summerfield's burn rate equation and is used to compute the burn rate augmentation based upon the additional burn area created when the flame penetrates the fissures. Comparisons are made with data obtained from published sources. The existence of threshold pressure and strains, above which augmentation occurs, is verified although the model predicts a lower threshold pressure and higher threshold strain than expected. Further results and applications of the model are discussed.

Langhenry, M. T.↗
NASA NTRS1992

Crack healing behavior of hot pressed silicon nitride due to oxidation

It is shown that limited oxidation of an MgO-containing, hot-pressed silicon nitride ceramic at 800 deg C and above results in increased strength due to crack healing. Slight oxidation of the surface produces enstatite and cristobalite which fills in cracks. More extensive oxidation leads to strength degradation due to the formation of new flaws by the evolution of N2 gas at the surface. The apparent fracture toughness also increased at 800 deg C and above due to oxidation. Bonds formed between the two surfaces of the crack during oxidation leads to a reduction in stress intensity at the crack tip, suggesting that valid high-temperature toughness values cannot be obtained in an air environment. The increase in strength due to crack healing by oxidation can be achieved without compromising the fatigue properties of the silicon nitride ceramic.

Choi, S. R.↗
NASA NTRS1994

Isothermal Damage and Fatigue Behavior of SCS-6/Timetal 21S [0/90](Sub S) Composite at 650 Deg C

The isothermal fatigue damage and life behaviors of SCS-6/Timetal 21S (0/90)s were investigated at 650 C. Strain ratcheting and degradation of the composite's static elastic modulus were carefully monitored as functions of cycles to indicate damage progression. Extensive fractographic and metallographic analyses were conducted to determine damage/failure mechanisms. Resulting fatigue lives show considerable reductions in comparison to (0) reinforced titanium matrix composites subjected to comparable conditions. Notable stiffness degradations were found to occur after the first cycle of loading, even at relatively low maximum stress levels, where cyclic lives are greater than 25,000 cycles. This was attributed to the extremely weak fiber/matrix bond which fails under relatively low transverse loads. Stiffness degradations incurred on first cycle loadings and degradations thereafter were found to increase with increasing maximum stress. Environmental effects associated with oxidation of the (90) fiber interfaces clearly played a role in the damage mechanisms as fracture surfaces revealed environment assisted matrix cracking along the (90) fibers. Metallographic analysis indicated that all observable matrix fatigue cracks initiated at the (90) fiber/matrix interfaces. Global de-bonding in the loading direction was found along the (90) fibers. No surface initiated cracks were evident and minimal if any (0) fiber cracking was visible.

Castelli, Michael G.↗