SEARCH · Engineering Papers

Results for “mode conversion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

All sources NASA NTRS DOE OSTI

NASA NTRS1993

Chronology, eruption duration, and atmospheric contribution of Apollinaris Patera, Mars

Geologic mapping from Viking image data of the Martian volcano Apollinaris Patera allowed identification of 6 major events that shaped its current morphology. Derivation of new topographic data allowed accurate estimates of the volume of erupted products from which estimates of an eruption duration are presented for the edifice and its corresponding atmospheric water contribution. Topographic data were acquired using stereophotogrammetric (Viking picnos 603A42, 639A92) techniques in both profiling and contouring modes (1 km contour). The profiling mode results in a more precise measurement than the contouring mode, but is limited in its areal coverage. The contour data are used in a more general sense to provide synoptic coverage for the volcano. These new stereophotogrammetric measurements constrain the topography to an accuracy of approximately 800 m vertically and approximately 1000 m horizontally. Conversion of the derived contour map to a raster based digital elevation model (DEM) was done by a growing contours interpolation. An ambiguity arises in this volume calculation due to an uncertainty regarding the actual base of the volcano relative to the pre-existing topography. Thus, the volume estimate was bracketed by using the 100 m and the 750 m elevations, which generally correspond to the lower and upper portions of the circumferential basal scarp, respectively. The resulting volumes are 103,000 cu km and 97,000 cu km; therefore the total volume of Apollinaris Patera is estimated to be approximately 100,000 cu km.

Robinson, M. S.↗

NASA NTRS2002

A Wavelength Optimization Study on Visible and Infrared Propagation Systems in Coastal Environments

Electro-optical (EO) systems employed for communications, surveillance and weapons systems are commonly assessed in the North American and European continents. However, the atmospheric propagation environment in these regions is often dissimilar to most other parts of the world. In particular, atmospheric dust, industrial pollution, and smoke frequently reduce visibility to less than 5 km in Asia and South America significantly hampering EO system performance. Because atmospheric aerosol species vary considerably in size and chemistry, optimal wavelengths for EO systems vary from region to region. In this paper we examine the extinction effects from aerosol particles and water vapor on a regional basis. Theoretical studies are coupled with visibility and satellite climatologies to make an assessment for the coastal regions of the world. While longer wavelengths permit higher transmission by particles in regions significantly hampered by fine mode particles (such as industrial pollution and smoke), this advantage is commonly offset by high extinction values from water vapor. This offsetting effect is particularly strong in industrial and developing countries in the tropics and sub-tropics such as Southeast Asia and South America. Conversely, the advantage of low water vapor concentrations in longer wavelengths is offset by high mass-extinction efficiencies of atmospheric dust in this portion of the spectrum.

Reid, J. S.↗

DOE OSTI2025

Collective Modes in Multilayer Graphene/𝛼−RuCl 3 Heterostructures

Collective modes in multilayer graphene, such as plasmons and phonons, exhibit sensitivity to displacement fields and interlayer coupling, distinguishing them from their counterparts in single-layer graphene. Here, we engineer collective modes in charge-transfer heterostructures composed of multilayer graphene and 𝛼−RuCl 3 . In heterostructures with a single 𝛼−RuCl 3 interface, the charge transfer generates displacement fields up to 7 V/nm at the interface between 𝛼−RuCl 3 and the adjacent graphene layer—the highest value achieved through charge-transfer methods. As a result of the broken inversion symmetry, we discover enhanced nonlinear optical response and modified phonon selection rules. Conversely, we find that multilayer graphene sandwiched between two 𝛼−RuCl 3 flakes causes displacement fields to cancel. There, we achieve carrier densities as high as 8 ×10 13 cm −2 in multilayer graphene and restore the phonon selection rules to their unperturbed state. Meanwhile, we demonstrate that plasmonic properties derive from the depletion of multiple valence bands. As a result of the quasilinear band dispersion, these “Dirac multiband plasmons” are relatively unaffected by displacement fields. On the other hand, the inverted heterostructure sequence—two multilayer graphene sheets encapsulating 𝛼−RuCl 3 —activates significant alteration of the plasmons via interlayer plasmon-plasmon coupling. Hence, multilayer graphene and 𝛼−RuCl 3 heterostructures offer a gate-free platform for engineering collective modes derived from inversion symmetry and interlayer coupling.

Moore, Samuel L. [Columbia University, New York, N↗

NASA NTRS1996

A Burst Mode, Ultrahigh Temperature UF4 Vapor Core Reactor Rankine Cycle Space Power System Concept

Static and dynamic neutronic analyses have been performed on an innovative burst mode (100's of MW output for a few thousand seconds) Ulvahigh Temperature Vapor Core Reactor (UTVR) space nuclear power system. The NVTR employs multiple, neutronically-coupled fissioning cores and operates on a direct, closed Rankine cycle using a disk Magnetohydrodynamic (MHD) generater for energy conversion. The UTVR includes two types of fissioning core regions: (1) the central Ultrahigh Temperature Vapor Core (UTVC) which contains a vapor mixture of highly enriched UF4 fuel and a metal fluoride working fluid and (2) the UF4 boiler column cores located in the BeO moderator/reflector region. The gaseous nature of the fuel the fact that the fuel is circulating, the multiple coupled fissioning cores, and the use of a two phase fissioning fuel lead to unique static and dynamic neutronic characteristics. Static neutronic analysis was conducted using two-dimensional S sub n, transport theory calculations and three-dimensional Monte Carlo transport theory calculations. Circulating-fuel, coupled-core point reactor kinetics equations were used for analyzing the dynamic behavior of the UTVR. In addition to including reactivity feedback phenomena associated with the individual fissioning cores, the effects of core-to-core neutronic and mass flow coupling between the UTVC and the surrounding boiler cores were also included in the dynamic model The dynamic analysis of the UTVR reveals the existence of some very effectlve inherent reactivity feedback effects that are capable of quickly stabilizing this system, within a few seconds, even when large positive reactivity insertions are imposed. If the UTVC vapor fuel density feedback is suppressed, the UTVR is still inherently stable because of the boiler core liquid-fuel volume feedback; in contrast, suppression of the vapor fuel density feedback in 'conventional" gas core cavity reactors causes them to become inherently unstable. Due to the strength of the negative reactivity feedback in the UTVR, it is found that external reactivity insertions alone are inadequate for bringing about significant power level changes during normal reactor operations. Additional methods of reactivity control such as variations in the gaseous fuel mass flow rate, are needed to achieve the desired power level oontrol.

Dugan, E. T.↗

DOE OSTI2023

Phonons in Copper Diphosphide (CuP 2 ): Raman Spectroscopy and Lattice Dynamics Calculations

Copper diphosphide (CuP 2 ) is an emerging binary semiconductor with promising properties for energy conversion and storage applications. While functionality and possible applications of CuP 2 have been studied, there is a curious gap in the investigation of its vibrational properties. In this work, we provide a reference Raman spectrum of CuP 2 , with a complete analysis of all Raman active modes from both experimental and theoretical perspectives. Raman measurements have been performed on polycrystalline CuP 2 thin films with close to stoichiometric composition. Detailed deconvolution of the Raman spectrum with Lorentzian curves has allowed identification of all theoretically predicted Raman active modes (9A g and 9B g ), including their positions and symmetry assignment. Furthermore, calculations of the phonon density of states (PDOS), as well as the phonon dispersions, provide a microscopic understanding of the experimentally observed phonon lines, in addition to the assignment to the specific lattice eigenmodes. We further provide the theoretically predicted positions of the infrared (IR) active modes, along with the simulated IR spectrum from density functional theory (DFT). Overall good agreement is found between the experimental and DFT-calculated Raman spectra of CuP 2 , providing a reference platform for future investigations on this material.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Hydrogen Adsorption, Reactivity, and Catalysis on Colloidal Iron Carbide Nanoparticles

Supported iron carbide particles have long served as catalysts for CO hydrogenation (the Fischer Tropsch synthesis, FTS) and continue to be attractive. Despite this, little is known about their chemistry. Reported here is a colloidal Fe x C nanoparticle (NP) model system that allows direct observation of surface hydrogen and CO, as well as quantification of the surface H. Dodecylamine-capped Fe x C NPs (DDA-Fe x C NPs) were synthesized through solution-phase carburization of Fe NPs and form stable colloids in low-polarity organic solvents. Treatment of these colloids with H 2 or D 2 produced highly hydrogenated materials, and FTIR spectra of DDA-Fe x C-D n showed that most of the D binds to carbides, with at least four distinct v(C-D) modes. The surface C-H(D) bonds were all reactive, transferring hydrogen to alkenes and other reagents in solution. Titration and ICP measurements showed a 0.17:1 ratio of added H:total Fe, or roughly. 40 H per 1.8 nm DDA-Fe x C NP. Conversely, CO was preferentially bound to surface Fe sites, with FTIR spectra showing a single broad v(CO) that shifted with CO coverage or co-adsorption of H 2 . The DDA-Fe x C NPs were active catalysts for both olefin hydrogenation and the FTS, under mild conditions and without catalyst pre-treatment. The CO hydrogenation reactions yielded a broad distribution of long-chain linear paraffins and olefins. Though quantitative comparisons with typical FTS results are not possible because of our use of sealed batch reactors and other factors, the observations of high catalytic reactivity demonstrate the relevance of this model system to iron-carbide catalysis. DFT calculations on model slab surfaces with varying iron carbide stoichiometries revealed that the thermodynamically preferred surface adsorption sites are C for H ads and Fe for CO ads . A variety of binding sites and binding energies were found for each adsorbate. We are unaware of previous studies indicating that a diverse array of C-H bonds is the primary source of reactive H on iron carbides. Experimentally, the diversity of *C-H sites was evident in reactions with H-atom donors and abstractors of different strengths, from both the reaction stoichiometries and IR spectra. The different surface–H binding energies correlate with the v(C-D) stretching frequencies. Furthermore, these insights into complex iron carbide surfaces and catalysis could assist catalyst design, and they showcase the importance of stoichiometric studies of reaction intermediates.

08 HYDROGEN↗

DOE OSTI2023

Grid-Integrated Production of Fischer-Tropsch Synfuels from Nuclear Power

Idaho National Laboratory (INL) investigates the relative economic profitability of an integrated energy system (IES) coupling an NPP with a synfuel production process at selected case study locations across the United States. In the synfuel IES, a high-temperature steam electrolysis (HTSE) plant is thermally and electrically coupled with an NPP to produce zero-carbon hydrogen. The synthetic fuel is produced from this H 2 combined with a CO 2 supply using the reverse water gas shift process followed by the Fischer-Tropsch (FT) reaction. This analysis considers a system in which the CO 2 is sourced from regional CO 2 emitters via the construction and operation of pipeline-based CO 2 supply networks. Locating the FT plant at the same site as the NPP and HTSE plants enables the NPP to provide zero-carbon heat and power to the HTSE plant and zero-carbon power to the FT plant as well as avoid the requirement for long-distance H 2 product transport from the HTSE plant to the FT plant. Hydrogen storage is used to enable the NPP to dispatch power to the electrical grid (instead of the HTSE plant) when grid demand increases, thus enabling the FT plant to continue to operate in a steady-state production mode. The ability to cease hydrogen production for several hours within each day enables the NPP to provide power to the grid to balance the electricity market during peak periods and maximize revenues for the nuclear synfuel IES. The FT process design considered has a 99% carbon conversion efficiency. The use of nuclear energy and nuclear energy-derived hydrogen enables synfuel production to achieve this high level of carbon utilization. Additionally, the life-cycle carbon emissions of the nuclear-based synfuel production process are very low, with WTW emissions of approximately 25 gCO 2 e/MJ, including steam credits (generated from FT process excess heat), and approximately 7 gCO 2 e/MJ, if steam credits are excluded. This compares favorably with the WTW emissions of 90.5 gCO 2 e/MJ for a compression-ignition, direct injection (CIDI) vehicle with a fuel economy of 31.6 miles per gallon gasoline equivalent (MPGGE), using low-sulfur diesel produced using conventional petroleum production and refining processes. Several NPPs in various regions of the U.S. are considered as case study analyses. Supply locations and transportation via pipeline of the CO 2 feedstock to the NPP site are analyzed through the National Energy Technology Laboratory (NETL) CO 2 Transport Cost model. The team finds that the amount of CO 2 generated by different sectors is sufficient for the synfuel production process at all locations considered. The CO 2 transportation costs are functions of the distance of the source to the NPP location, the CO 2 capture cost at the source, and the quantity of CO 2 transported. Historical electricity prices for the NPP case study locations are collected and analyzed. Monthly average prices, price range, and duration of negative-price periods vary among these locations. For each location, an auto-regressive moving average (ARMA) model is trained on historical electricity price data. ARMA validation is done to ensure the synthetic price distributions represent one of historical prices with high fidelity. Synthetic time series from these ARMA models are used in a coupled dispatch and system optimization in the Holistic Energy Resource Optimization Network (HERON) to compute the differential net present value (NPV) of the IES. The team finds that this econometric is positive, ranging from $14M–1.3bn (2020) depending on the location. The optimal synfuel IES configuration to obtain this increase in NPV often maximizes the size of the synfuel production process with regards to the size of the NPP. However, the team shows that the NPP still plays a stabilizing role for the grid: In periods of high prices and high loads, more electricity from the NPP is sent to the grid. A high variability of electricity prices and extreme maximum prices tend to drive up electricity production. While it requires significant investment, the synfuel IES could increase the economic profitability for the existing fleet of LWRs across the country while still maintaining the grid stabilizer role of NPPs. During its lifetime, the main costs for the nuclear synfuel IES are the carbon feedstock transportation costs, followed by the capital expenses (CAPEX) and operation and maintenance (O&M) costs while the revenue comes first from the IRA H 2 production tax credit (PTC) and then from the sales of synfuel products. The profitability of the synfuel IES is most sensitive to the value of the hydrogen PTC and the synfuel products as well as the cost of the carbon feedstock, highlighting the importance of governmental incentives regarding hydrogen, carbon emissions, and synfuel in driving the deployment of future nuclear synfuel IESs.

08 HYDROGEN↗

NASA NTRS2011

Sub-Shot Noise Power Source for Microelectronics

Low-current, high-impedance microelectronic devices can be affected by electric current shot noise more than they are affected by Nyquist noise, even at room temperature. An approach to implementing a sub-shot noise current source for powering such devices is based on direct conversion of amplitude-squeezed light to photocurrent. The phenomenon of optical squeezing allows for the optical measurements below the fundamental shot noise limit, which would be impossible in the domain of classical optics. This becomes possible by affecting the statistical properties of photons in an optical mode, which can be considered as a case of information encoding. Once encoded, the information describing the photon (or any other elementary excitations) statistics can be also transmitted. In fact, it is such information transduction from optics to an electronics circuit, via photoelectric effect, that has allowed the observation of the optical squeezing. It is very difficult, if not technically impossible, to directly measure the statistical distribution of optical photons except at extremely low light level. The photoelectric current, on the other hand, can be easily analyzed using RF spectrum analyzers. Once it was observed that the photocurrent noise generated by a tested light source in question is below the shot noise limit (e.g. produced by a coherent light beam), it was concluded that the light source in question possess the property of amplitude squeezing. The main novelty of this technology is to turn this well-known information transduction approach around. Instead of studying the statistical property of an optical mode by measuring the photoelectron statistics, an amplitude-squeezed light source and a high-efficiency linear photodiode are used to generate photocurrent with sub-Poissonian electron statistics. By powering microelectronic devices with this current source, their performance can be improved, especially their noise parameters. Therefore, a room-temperature sub-shot noise current source can be built that will be beneficial for a very broad range of low-power, low-noise electronic instruments and applications, both cryogenic and room-temperature. Taking advantage of recent demonstrations of the squeezed light sources based on optical micro-disks, this sub-shot noise current source can be made compatible with the size/power requirements specific of the electronic devices it will support.

Strekalov, Dmitry V.↗

NASA NTRS2003

164-GHz MMIC HEMT Frequency Doubler

A monolithic microwave integrated circuit (MMIC) that includes a high-electron-mobility transistor (HEMT) has been developed as a prototype of improved frequency doublers for generating signals at frequencies greater than 100 GHz. Signal sources that operate in this frequency range are needed for a variety of applications, notably including general radiometry and, more specifically, radiometric remote sensing of the atmosphere. Heretofore, it has been common practice to use passive (diode-based) frequency multipliers to obtain frequencies greater than 100 GHz. Unfortunately, diode-based frequency multipliers are plagued by high DC power consumption and low conversion efficiency. Moreover, multiplier diodes are not easily integrated with such other multiplier-circuit components as amplifiers and oscillators. The goals of developing the present MMIC HEMT frequency doubler were (1) to utilize the HEMT as an amplifier to increase conversion efficiency (more precisely, to reduce conversion loss), thereby increasing the output power for a given DC power consumption or, equivalently, reducing the DC power consumption for a given output power; and (2) to provide for the integration of amplifier and oscillator components on the same chip. The MMIC frequency doubler (see Figure 1) contains an AlInAs/GaInAs/InP HEMT biased at pinch-off to make it function as a class-B amplifier (meaning that it conducts in half-cycle pulses). Grounded coplanar waveguides (GCPWs) are used as impedance-matching transmission lines. Air bridges are placed at discontinuities to suppress undesired slot electromagnetic modes. Another combination of GCPWs also serves both as a low-pass filter to suppress undesired oscillations at frequencies below 60 GHz and as a DC blocker. Large decoupling capacitors and epitaxial resistors are added in the drain and gate lines to suppress bias oscillations. At the output terminal, the fundamental frequency is suppressed by a quarter-wave open stub, which presents a short circuit at the fundamental frequency and an open circuit at the second harmonic. At an input power of 7 mW, the output power and conversion loss at an output frequency of 164 GHz were found to be 5 dBm (approximately equal to 3.2 mW) and 2 dB, respectively, with a 3-dB output-power bandwidth of 14 GHz. This is the best performance reported to date for an MMIC HEMT frequency doubler above 100 GHz.

Samoska, Lorene↗

DOE OSTI2025

Intermodal microwave-to-optical transduction using silicon-on-sapphire optomechanical ring resonator

Optomechanical and electro-optomechanical systems have emerged as one of the most promising approaches for quantum microwave-to-optical transduction to interconnect distributed quantum modalities for scaling the quantum systems. These systems use suspended structures to increase mode overlap and mitigate loss to achieve high efficiency. However, the suspended design’s poor heat dissipation under strong drive limits the ultimate efficiency. Here, we demonstrate an unsuspended optomechanical ring resonator (OMR) based on the silicon-on-sapphire (SOS) platform for microwave-to-optical frequency conversion. The OMR achieves a triply resonant optical-to-optical conversion with an enhanced coupling rateG b = 3.6 gigahertz per square-root milliwatt at a peak conversion efficiency of 1.2% with 3.6-milliwatt microwave drive power and a microwave-to-optical conversion efficiency of 1.5 × 10 −5 at 10-milliwatt optical drive power. Our results show that the unsuspended SOS platform, which mitigates the thermal effect and is compatible with superconducting qubits, is a promising platform for optomechanical circuitry and quantum transduction.

Science & Technology - Other Topics↗

DOE OSTI2024

Theoretical Understanding of Effects of Operating Modes on the Performance Durability of Solid Oxide Cells: A Comparison between Potentiostatic and Galvanostatic Operations

In solid oxide cells (SOCs), the choice between galvanostatic (constant current) and potentiostatic (constant voltage) modes does not significantly affect the performance of SOCs as long as the cell components remain unchanged and intact. However, the degradation of cell components, which leads to changes in electrochemical and physical properties of the cell, elevates the importance of the selected operating mode. This paper aims to investigate the effects of galvanostatic and potentiostatic operating modes on the evolving properties of SOCs and their subsequent influence on performance durability. Employing non-equilibrium thermodynamic analysis, a crucial approach for understanding the degradation phenomena within an active electrochemical system, this study aims to provide in-depth insights into how these operating modes affect the longevity and efficacy of SOCs. Key findings include: In cases where oxygen electrode (OE) degradation is accelerated by higher partial pressure of oxygen ( p O 2 ), operating under constant voltage electrolysis can mitigate the high p O 2 at the OE|electrolyte (OE|EL) interface. Conversely, if OE degradation occurs more rapidly under a lower p O 2 , constant current electrolysis is more effective in suppressing degradation by achieving a high p O 2 at the OE|EL interface. For degradation of the fuel electrode (FE) due to higher p O 2 , constant current electrolysis is beneficial for more stable performance, which helps maintain low p O 2 at the FE|EL interface. When FE degradation is accelerated by lower p O 2 , constant voltage electrolysis can avert low p O 2 at the FE|EL interface. In practical scenarios, more complex degradation mechanisms come into play, especially when p O 2 significantly deviates from initial conditions. Degradation in one electrode can influence p O 2 in the other electrode, a phenomenon more pronounced in potentiostatic than in galvanostatic electrolysis.

Electrochemistry↗

DOE OSTI2022

Durable, High-Performance Unitized Reversible Fuel Cells Based on Proton Conductors

The main objective of this project was to develop robust, highly efficient, and economically viable H + -conducting membrane-based, unitized reversible fuel cell (H-URFC) technology for large-scale co-located energy storage and power generation. Another objective of this project is to gain a profound understanding of the degradation mechanisms of key stack materials and interfaces using various in situ, ex situ, and operando measurements guided by theoretical analysis. Nanostructured components will be integrated into cell design and the interfaces between electrodes and electrolyte will be modified with active bi-functional catalysts and protective coatings in order to achieve >70% roundtrip efficiency at 1 A/cm2 in both the fuel cell and the electrolysis modes. The end goal of the project is to advance the technology to the point that a university-industry collaboration can be established to scale up the technology for early adoption, and eventually enabling a pathway to large-scale energy storage that utilizes chemical storage and conversion for electrical grid balancing.

08 HYDROGEN↗

NASA NTRS1975

Solar electric and thermal conversion system in close proximity to the consumer

Solar cells may be used to convert sunlight directly into electrical energy and into lowgrade heat to be used for large-scale terrestrial solar-energy conversion. Both forms of energy can be utilized if such cells are deployed in close proximity to the consumer (rooftop). Cadmium-sulfide/copper-sulfide (CdS/Cu2S) solar cells are an example of cells which may be produced inexpensively enough to become economically attractive. Cell parameters relevant for combined solar conversion are presented. Critical issues, such as production yield, life expectancy, and stability of performance, are discussed. Systems-design parameters related to operating temperatures are analyzed. First results obtained on Solar One, the experimental house of the University of Delaware, are given. Economic aspects are discussed. Different modes of operation are discussed in respect to the power utility and consumer incentives.

Boeer, K. W.↗

NASA NTRS2003

Investigation of Pneumatic Inlet and Diffuser Blowing on a Ducted Fan Propulsor in Static Thrust Operation

Tilting ducted fans present a solution for the lifting and forward flight propulsion requirements of VTOL aircraft. However, the geometry of the duct enshrouding the propeller has great a effect on the efficiency of the fan in various flight modes. Shroud geometry controls the velocity and pressure at the face of the fan, while maintaining a finite loading out at the tips of the fan blades. A duct tailored for most efficient generation of static lifting thrust will generally suffer from performance deficiencies in forward flight. The converse is true as well, leaving the designer with a difficult trade affecting the overall performance and sizing of the aircraft. Ideally, the shroud of a vertical lifting fan features a generous bell mouth inlet promoting acceleration of flow into the face of the fan, and terminating in a converging nozzle at the exit. Flow entering the inlet is accelerated into the fan by the circulation about the shroud, resulting in an overall increase in thrust compared to an open propeller operating under the same conditions . The accelerating shroud design is often employed in lifting ducted fans to benefit from the thrust augmentation; however, such shroud designs produce significant drag penalties in axial flight, thus are unsuitable for efficient forward flight applications. Decelerating, or diffusing, duct designs are employed for higher speed forward flight configurations. The lower circulation on the shroud tends to decelerate the flow into the face of the fan, which is detrimental to static thrust development; however, net thrust is developed on the shroud while the benefits of finite blade loading are retained. With judicious shroud design for intended flight speeds, a net increase in efficiency can be obtained over an open propeller. In this experiment, conducted under contract to NASA LaRC (contract NAG-1-02093) circulation control is being applied to a mildly diffusing shroud design, intended for improved forward flight performance, to generate circulation in the sense of an accelerating duct design. The intent is to improve static thrust performance of a ducted fan tailored for high speed axial flight, while at the same time significantly reduce the pressure signature on the ground plane. Circulation control on the fan shroud is achieved by the Coanda effect.

Kondor, Shayne↗

DOE OSTI2023

Computer-controlled finishing via dynamically constraint position-velocity-time scheduler

In a Computer Numerical Controlled (CNC) finishing process, the target material removal from an optical surface is guided by the convolution between the influence function of a machine tool and its dwell time at certain points over the surface. To reduce dynamics stressing and increase machining efficiency, the dwell time must be converted to varying velocities, which are the actual inputs to the machine tool controller. Conventionally, the conversion assumed constant acceleration and relied on linear motion interpolation, which caused discontinuities in velocities. This unsmooth motion affects the material removal distribution, and, thus, the accuracy of the finished surface shape. Many modern CNC machines support the smoother, cubic-polynomial interpolated Position-Velocity-Time (PVT) motion mode; however, the conventional scheduler may fail to provide suitable velocities for the PVT. Here in this study answers this challenge by proposing a novel PVT-based velocity scheduler that achieves smooth motion while considering CNC dynamic limits. Firstly, the principle of the PVT is explained, and the PVT-based velocity scheduler is formulated. Secondly, a quadratic programming is used to optimize the velocities by imposing the CNC dynamic constraints and the C 1 continuities (zeroth and first derivatives are continuous) simultaneously. Thirdly, the smoothness and accuracy of the scheduled velocities are studied on different kinds of tool paths via simulation. Finally, a sub-0.3 nm level surface finishing experiment using ion beam figuring is demonstrated to verify the feasibility of the proposed method. The PVT-based scheduler and simulator code is open-sourced.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Structural color from a coupled nanowire pair beyond the bonding and antibonding model

Optical resonances in nanostructures can be harnessed to produce a wide range of structural colors. Conversely, the analysis of structural colors has been used to clarify the nature of optical resonances. Here, we show that silicon nanowire (NW) pairs can display a wide range of structural colors by controlling their radiative coupling. This is accomplished by exciting a series of Fabry–Pérot-like modes where light is repeatedly scattered between two NWs. These modes are beyond the expectation from the conventional chemical bonding model under a quasi-electrostatic approximation, in which only bonding and antibonding modes can be formed in a pair system through modal hybridization. The additional eigenmodes found in a two-resonator system originate from the nonlinear, frequency-dependent coupling strength derived from the radiative nature of low- Q resonators. The Fabry–Pérot modes can be tuned across the entire visible frequency range by varying the distance between two NWs, leading to what we believe is a new type of universal building blocks that can provide structural color within a subwavelength footprint. The presented results pave the way toward the design and usage of highly tunable resonances that exploit the radiative coupling of high-index nanostructures.

Li, Qitong↗

NASA NTRS1976

Possibility of detecting magnetospheric radio bursts from Uranus and Neptune

The intensity of magnetospheric radio bursts (MRBs) is scaled to solar-wind input into planetary magnetospheres and the frequency of emission is scaled to polar surface magnetic-field strength in order to estimate the possibility of detecting MRBs from Uranus and Neptune. A scaling law is derived which relates the ratio of power radiated in MRBs to the solar-wind input for earth, Jupiter, and Saturn. Power-flux spectra of MRBs from these three planets are plotted, and it is shown that Jupiter and Saturn may radiate 1% to 5% of the solar-wind energy input into their magnetospheres. The properties of MRBs from Uranus and Neptune are estimated by assuming a conversion efficiency of 1% to 5%, a bandwidth of half the peak frequency, and conformity of Uranus' and Neptune's dipole moments with the magnetic Bode's law. Based on the results, it is suggested that detection of MRBs from these two planets may be a reasonable cruise-mode radio-astronomy objective on future missions to the outer solar system.

Kennel, C. F.↗

NASA NTRS1983

Research on spacecraft electrical power conversion

The history of spacecraft electrical power conversion in literature, research and practice is reviewed. It is noted that the design techniques, analyses and understanding which were developed make today's contribution to power computers and communication installations. New applications which require more power, improved dynamic response, greater reliability, and lower cost are outlined. The switching mode approach in electronic power conditioning is discussed. Technical aspects of the research are summarized.

Wilson, T. G.↗