Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Microstructure and Properties of Mn-Cu-Based Damping Alloys Prepared by Ball Milling and Hot-Press Sintering

A Mn-Cu-based damping alloy with a nominal composition of 70Mn-24Cu-3Zn-3Al (at.%) was prepared by ball milling of pure elemental powders and subsequent hot-press sintering of powder mixture at 750 and 825 °C for 2 h. For comparison, this alloy was also prepared by induction melting technology and then homogenized at 850 °C for 24 h. Further, they were aged at 430 °C for 2 h. The microstructure, damping capacity and microhardness of the hot-press-sintered and induction-melted alloys have been investigated. The results show that the microstructure of the powder mixture upon ball milling mainly comprises convoluted composite particles containing α-Mn and γ-Cu phases, and isolated α-Mn ones around. The high compactness of the alloys is obtained after hot-press sintering (94.8 and 98.6% at 750 and 825 °C, respectively). At a holding temperature of 750 °C, the microstructure of the alloy is primarily composed of γ-MnCu, γ-CuMn and α-Mn grains. With increasing the target temperature to 825 °C, the single γ-MnCu solid solution has been formed in the alloy by diffusion of Mn etc. into γ-Cu lattices. The hot-press-sintered alloys (especially at 825 °C) possess relatively high damping capacity although which is still lower than that of induction-melted one. In contrast, the microhardness of the hot-press-sintered alloys (especially at 750 °C) is obviously higher than that of the induction-melted one.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Forging on Microstructure, Mechanical Properties and Acoustic Emission Characteristics of Al Alloy (2014): 10 wt.% SiC{sub p} Composite

In this paper a systematic study has been undertaken to study the effect of forging on microstructure, mechanical properties and acoustic emission (AE) characteristics of Al alloy (2014)—10 wt.% SiC metal-matrix composites. Hammer forging was carried out at a temperature of 470 °C in an open die, with a deformation ratio of 3.5:1. Microstructural analyses were carried out at three different positions of forged billet. Significant material flow was observed in the sample taken from the sides of the forged billet, but no appreciable material flow was observed at the center of the forged billet. The microstructural characterization showed that forging resulted in cracking of SiC particles in Al alloy (2014)—10 wt.% SiC composite. The AE results during forging showed an increase in AE signal intensity during the initial yielding period and a subsequent decrease in the intensity of AE signals with sudden burst at the end of the forging. The plastic deformation at room temperature was less ductile in nature but at high temperature, appreciable ductility was observed. The FESEM micrographs of fracture surfaces of the tensile specimens showed appreciable clustering of SiC particles during plastic deformation both at room and high temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Laser 3D Printing of Fe-Based Bulk Metallic Glass: Microstructure Evolution and Crack Propagation

This work presents a comprehensive study of microstructure evolution, crack development and hardness performance of Fe-based bulk metallic glass parts processed by laser 3D printing. The combination of a low scan speed and high energy density generates a low temperature gradient, leading to supercooling and the formation of coarse dendrite and cellular crystal microstructure. Columnar dendrites grow in a single direction with large stress, and cracks are easily formed between the dendrites. The stress intensity factor (SIF) caused by the crack surface tension is small, the crack healing effect is weak, and it is difficult to prevent crack propagation. Cellular grain growth is uniform and more easily accommodates the strain, preventing crack initiation and propagation. In contrast, use of a high scan speed with low energy input produces a fine and uniform dendrite or even nanocrystalline, microstructure with microcracks. The SIF caused by the crack surface tension is large, and the crack healing effect is strong and prevents crack initiation and propagation. For low energy density, the hardness of the sample is similar to the hardness of the cast amorphous. This result indicates that the printing sample retained some amorphous characteristics.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure and Mechanical Properties of a SiO{sub 2} Ceramic and TC4 Alloy Joint Brazed with a Nanocomposite Filler

Vacuum brazing of TC4 alloy and SiO{sub 2} ceramic was achieved using a nano-AgCuNi braze alloy. The melting temperature of nano-AgCu powders was analyzed by differential scanning calorimeter. Furthermore, the effects of the Ni content on the microstructure and mechanical properties of the joints were studied. The results showed that the melting temperature of the nano-AgCu filler was 774 °C. A decrease in the melting temperature of 6 °C was observed, compared with the general AgCu filler, and this decrease enabled the interfacial reaction of the joint to begin earlier. The typical interfacial microstructure of the TC4/nano-AgCuNi/SiO{sub 2} ceramic joint brazed at 950 °C for 10 min was TC4/α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectoid structure/Ti{sub 2}(Cu,Ni) compound with α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectic structure/Ti{sub 4}O{sub 7} + TiSi{sub 2}/SiO{sub 2} ceramics. The homogeneous microstructure of α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectoid structure primarily existed in the diffusion layer. Additionally, the refined α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectic structure created via a eutectic reaction and Ti{sub 2}(Cu,Ni) compound was distributed in the brazing seam. The Ni content could influence the formation of Ti-Cu-Ni ternary intermetallic compounds (IMCs). An increase in Ni led to an increase in the α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectic structure in the brazing seam. The shear strength of the brazed joints first increased and then decreased with the increase in the nano-Ni content, and the optimal shear strength of 30.1 MPa was achieved at 10 wt.% Ni. The increase in the α-Ti + Ti{sub 2}(Cu,Ni) + Ti{sub 2}(Ni,Cu) hypereutectic structure and the decrease in brittle compounds enhanced the shear strength of the joint. Fracture analysis of the joints brazed at 950 °C for 10 min indicated that the cracks mainly occurred in SiO{sub 2} ceramic.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Rolling Deformation on the Microstructure and Mechanical Properties of an Extruded Mg-Zn-Ca Alloy

The microstructure and mechanical properties of an as-extruded Mg-4.5Zn-1.1Ca (wt.%) alloy subjected to unidirectional rolling and cross-rolling were compared in the present study. The results indicated that rolling deformation refined the microstructure, dispersed second phases and modified the texture, which resulted in an improvement in the mechanical properties of the as-rolled alloys compared with those of the as-extruded alloy. The yield strength of the Mg-4.5Zn-1.1Ca (wt.%) alloy increased from 173 to 297 MPa after unidirectional rolling. The initial fragmented Ca{sub 2}Mg{sub 6}Zn{sub 3} phases were further refined after rolling deformation, which clearly restricted the grain growth and gave rise to a fine microstructure. It was also found that rolling deformation intensified the basal texture in comparison with the as-extruded alloy, which was related to particle pinning.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructural Transition of (CuFeMnNi){sub 1−x}Cr{sub x} (x = 0-0.25) High-Entropy Alloys

The influence of Cr on the microstructure and hardness of the cast and annealed (CuFeMnNi){sub 1−x}Cr{sub x} (x = 0, 0.05, 0.1, 0.15, 0.2 and 0.25) high-entropy alloys were investigated systematically. The results revealed that the microstructures of (CuFeMnNi){sub 1−x}Cr{sub x} (x = 0, 0.05 and 0.1) alloys were composed of (Fe, Ni and Cr)-rich FCC1 and (Cu, Mn)-rich FCC2 phases. No obvious change in the dendritic size was detected between cast and related annealed alloys, indicating the excellent thermal structure stability of the studied alloys. The microstructures of the cast (CuFeMnNi){sub 1−x}Cr{sub x} (x = 0.15, 0.2 and 0.25) alloys contained FCC1, FCC2 and (Cr, Fe)-rich BCC phases, while those of the annealed alloys were composed of FCC1, FCC2 and ρ phases. The significant transition from BCC phase to ρ phase was detected. Moreover, the hardness of both cast and annealed (CuFeMnNi){sub 1−x}Cr{sub x} alloys increased with the increasing Cr content. The hardness of annealed (CuFeMnNi){sub 1−x}Cr{sub x} (x = 0, 0.05 and 0.10) alloys reduced slightly as compared to corresponding cast alloys, whereas the hardness of the annealed (CuFeMnNi){sub 1−x}Cr{sub x} (x = 0.15, 0.2 and 0.25) alloys increased.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Homogenization Treatment and Microalloying with Mn on the Microstructure and Hot Workability of AA6060 Aluminum Alloys

The effects of a homogenization treatment and microalloying with Mn on the evolution of the microstructure and hot workability of AA6060 aluminum alloys were investigated. Various homogenization treatments with temperatures ranging from 520 to 610 °C and soaking times from 2 to 16 h were conducted. The results revealed that β-AlFeSi intermetallic was the dominant phase in the as-cast microstructure of the experimental alloys. During the homogenization, the fragmentation of intermetallics occurred and plate-like β-AlFeSi transformed into rod-like α-AlFeSi. In addition, a number of dispersoids precipitated in the 0.1Mn alloy in the temperature range of 520-580 °C. The flow stress behavior of the homogenized AA6060 alloys was mainly determined by the solid solution level. Increasing homogenization temperatures resulted in higher flow stresses owing to the increase in solute atoms in the aluminum matrix. The incremental Mn addition from 0 to 0.1% moderately increased the flow stress by up to 3%. Grain growth occurred in the alloys with low Mn contents (< 0.03Mn) during the high-temperature homogenization (580-610 °C), which resulted in a sudden decrease in the flow stresses and an irregular sample shape after the deformation. Microalloying with Mn (> 0.06%) can effectively prevent grain growth at such temperatures. For an alloy with Mn (0.1%) microalloying, homogenization at 550-580 °C for 6 h could be the optimal condition to balance the flow stress and desirable microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Evaluation of the Microstructure and Performance of Fe-21Cr-15Ni-6Mn-Nb Nonmagnetic Stainless Steel Welded Joints

In the present study, double-sided gas shield welding (GSW), in a single pass, was applied to Fe-21Cr-15Ni-6Mn-Nb nonmagnetic stainless steel plate. The microstructure and performance of the welded joint were investigated via microstructural and phase analysis, mechanical testing and magnetic analysis. The results showed a satisfactory micrographic appearance with full penetration, and no solidification defects observed in the welded joint, which showed typical epitaxial growth characteristics in the welding solidification. Slight grain growth, with an average size of ~ 18.9 μm, occurred in the heat-affected zone (HAZ). The primary dendrite arms, on both sides of welding joint, grew along the direction of the temperature gradient and met at the centerline of the weld with no parting microstructure in evidence. The secondary dendrite arm spacing was stable in all parts of the weld zone (WZ). The hardness of the weld zone was higher than that of the HAZ and the base metal (BM), with the lowest hardness occurring in the HAZ. The results of tensile testing showed a higher strength of the welded metal (WM) compared to the BM, and a good strength-ductility balance of the welded joint. The impact energy of the HAZ was higher than that of the WZ, corresponding to 60.5 J at room temperature and 52.7 J at − 196 °C. Microvoid coalescence, concurrent with crack propagation along the direction of the long axis of the dendritic sub-grains, was observed during plastic deformation in the WZ. Additionally, the excellent paramagnetic characteristics of the welded specimens were revealed.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructures and Impact Wear Behavior of Al-Alloyed High-Mn Austenitic Cast Steel After Aging Treatment

The microstructural evolution and impact wear behavior of Al-alloyed ultra-high-Mn austenitic cast steel were investigated after different heat treatments, including quenching (Q) and quenching + aging (Q + A). Another ultra-high-Mn austenitic cast steel without Al was compared under the same experimental condition. After Q + A, Al addition contributed to the precipitation of κ-carbides which improves the yield strength and wear resistance of the austenite matrix. However, the mechanical properties and wear resistance of the Al-free steel were strongly deteriorated due to the precipitation of plate-like M{sub 3}C-type carbides, as well as the worn surface of the Al-free steel had the feature of micro-scratches. After Q + A (2 h), the Al-alloyed steel obtained optimal wear resistance and the main wear feature was strain fatigue. But, excessive aging time (4 h) would lead to a large fragile peeling from the worn surface and the wear resistance was decreased. Also, the worn subsurface microstructures with different heat treatments were observed by transmission electron microscopy (TEM). These results show that the deformation microstructures of the Al-free steel contained stacking faults, dislocation tangle and deformation twins. The deformation character of Al-alloyed steel is dominated by planar glide, and with increase in the aging time, planar dislocation substructures gradually evolved, relating to dislocation pileups, Taylor lattices and micro-bands.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructural Evolution and Properties of 24CrNiMoY Alloy Steel Fabricated by Selective Laser Melting

24CrNiMoY alloy steel samples were fabricated by selective laser melting (SLM), and a phase transformation model was established to study the alloy steel microstructural evolution. Meanwhile, microhardness and tensile properties of 24CrNiMoY alloy steel prepared by different laser energy densities (E{sub v}) were investigated. Results indicate that the microstructural evolution of 24CrNiMoY alloy steel is consistent with the phase transformation model. The main microstructure changed from martensite to bainite with the increase in thermal cycle numbers. In addition, a suitable E{sub v} plays an important role in refining the bainite structure and improving the alloy steel properties. When the E{sub v} decreases from 210 to 140 J/mm{sup 3}, the bainite lath width reduces from 1.7 to 0.6 μm. Simultaneously, the relative density, tensile strength and microhardness of the fabricated samples increase first and decrease later. 24CrNiMoY alloy steel sample prepared by 160 J/mm{sup 3} has fine mechanical properties: The tensile strength is 850 MPa and microhardness is 360 HV{sub 0.2}.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Flow Patterns, Microstructure and Mechanical Properties of AZ31/Al6061 Dissimilar Friction Stir-Welded Joints

Dissimilar joints between die-cast AZ31 and extruded Al6061-T6 were joined using friction stir welding technology at a constant transverse speed (50 mm/min) and rotation rate of 800 or 1000 rpm. The flow patterns, microstructure evolution and intermetallic compounds in dissimilar joints were studied by optical and scanning electron microscopy. The relationship between microstructure and tensile properties was analyzed. The microhardness distribution along the horizontal centerline in cross section was investigated. Local flow without obvious mixing existed between Mg and Al metals in the tool shoulder-affected zone. For the tool-pin-affected zone, two typical zones, namely, the “extrusion zone” and “flow zone” existed because of the different flow modes of the plastic metals. The phase analysis showed that intermetallic compounds, including Al{sub 12}Mg{sub 17} and Al{sub 3}Mg{sub 2} formed in banded structures. Phase analysis showed that a joint with welding parameters of 800 rpm and 50 mm/min (Joint-500) had good mechanical properties because of the more uniform microstructure distribution and fewer intermetallic compounds. Fracture analysis indicated some microvoids and lamellate intermetallic compounds in the fracture surface of the joint with welding parameters of 1000 rpm and 50 mm/min (Joint-1000), which deteriorated its tensile strength significantly.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Beam Current Effect on Microstructure and Properties of Electron-Beam-Melted Ti-6Al-4V Alloy

In this study, a noncommercial 3D printing machine was used to fabricate Ti-6Al-4V alloy by electron-beam melting (EBM). The influence of beam current on the microstructure, phase composition and mechanical properties of electron-beam-melted Ti-6Al-4V alloy was investigated. Numerical simulation is implemented to evaluate thermal fields during electron-beam melting of Ti-6Al-4V powder. The decrease in beam current from 3.5 to 2.5 mA leads to refinement of microstructure: The average width of α plates decreases from 10 down to 6 μm. The formation of finer microstructure is attributed to higher cooling rate at lower beam current confirmed by simulation. The phase composition of EBM Ti-6Al-4V indirectly depends on the beam current. High content of β phase (7%) was achieved at the beam current of 3 mA. The produced Ti-6Al-4V samples are characterized by high microhardness (470-520 HV).

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructural Development and Mechanical Properties of Friction Stir Welded Ferritic Stainless Steel AISI 409

This work investigates the effect of friction stir welding process parameters (rotation rate and traverse speed) on the microstructural evolution of friction stir welded (FSWed) ferritic stainless steel (FSS) AISI 409. Optical microscope, scanning electron microscope and electron backscattering diffraction are used to quantitatively assess the development in grain structure and texture. The microstructural development suggested that thermo-mechanical deformation occurs in the stir zone within the austenite/ferrite phase region, ultimately transforming upon cooling into bainitic/ferritic microstructure. The fraction and size of the bainitic/ferritic grains are found to vary through the thickness of the joints. High fractions of coarse ferritic grains are found near the top of the stir zone, and low fraction of fine ferritic grains is found near the bottom of the stir zone. This bainitic/ferritic grain structure resulted in an increase in the hardness of the stir zone by about 74% relative to the base material. The tensile strength of the FSWed FSS joints is almost at the same level of the base material with reduction in the ductility as a result of the increased hardness of the weld zone.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure, Mechanical Properties and Residual Stress of Selective Laser Melted AlSi10Mg

AlSi10Mg processed by selective laser melting (SLM) is common in various industries because of its complex structure and high performance. The microstructure, residual stress and mechanical properties restrict its application, while they are affected by the scanning path type and preheating temperature. In this work, to investigate the properties of selective laser melted AlSi10Mg alloys and gain better performance results, the microstructure and mechanical tests are performed at several preheating temperatures based on the uniformity and chessboard scanning strategy. It is found that the selective laser melted AlSi10Mg parts fabricated in the chessboard scanning path have better mechanical properties than those fabricated in the uniformity scanning path. Furthermore, a higher preheating temperature can induce less residual stress due to the enhanced Al crystal faces. Finally, analyses of the microstructures, mechanical and residual stress provide a valuable suggestion that the combination of the range of preheating temperature and the scanning path can improve the performance of selective laser melted AlSi10Mg.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Influence of Single-Point Incremental Force Process Parameters on Forming Characteristics and Microstructure Evolution of AA-6061 Alloy Sheet

Single-point incremental forming (SPIF) process comprises a set of process variables, such as forming tool diameter, vertical pitch, spindle rotation speed, and tool velocity, which may affect the forming behavior of the sheet to be deformed. The objective of this work is to study the effect of SPIF process parameters on forming characteristics and microstructure development for the AA-6061 (T6) aluminum alloy sheet. The SPIF experiments and finite element (FE) simulations were performed at different process parameters to achieve conical shapes from the AA-6061 blanks. The effect of process parameters on forming forces, thickness uniformity in wall region of the cone and surface roughness of the blank was analyzed. A detailed microstructure study was performed to analyze the effect of process variables on microstructure and texture evolution during the SPIF process. This study reveals that the process parameters are likely to influence the texture development especially at high tool diameter and vertical pitch values. Therefore, suitability and consequences of using different combinations of tool diameter and vertical pitch values are discussed for AA-6061 alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure and Mechanical Behavior of Friction Stir-Welded Sc-Modified Al-Zn-Mg Alloys Made Using Different Base Metal Tempers

The microstructure and property of friction stir weld joints of a Sc-modified Al-Zn-Mg alloy developed using base metal in hot-rolled (HR) and T6 temper were studied and compared in this work. The results showed that the microstructure and property exhibited significant difference between the two friction stir weld joints. The weld efficiency of the FSW joint developed using base metal in HR condition is over 90%, while that of the FSW joint developed using base metal in T6 condition is only 70%. The hardness of the weld nugget of HR joint is obviously higher than that of the weld nugget of T6 joint, due to the different changes in the original precipitates during the friction stir welding process. The strengthening mechanism in different zones of the two FSW joints was discussed to examine the microstructure–properties relationship, and the main difference of the strengthening mechanism between the two FSW joints was revealed.

36 MATERIALS SCIENCE↗
DOE OSTI2019

An Algorithm to Generate Synthetic 3D Microstructures from 2D Exemplars

The inverse problem of constructing 3D microstructures from 2D data is an area of active research within the materials science community. This paper presents the implementation of a robust, computationally efficient algorithm, Hierarchical Algorithm for the Reconstruction of Exemplars (HARE), written in Python to reconstruct 3D features in a given microstructure from up to three orthogonal 2D exemplars using nearest neighbor matching to reproduce feature qualities, such as shape, size, and distribution. HARE’s feature sampling implements histogram reweighting to avoid both over- and undersampling. A neighborhood voting scheme allows each pixel to provisionally affect its neighbors according to its weight. Finally, the algorithm is presently configured for two-phase materials and is being extended to accommodate multiple phases. HARE is a convenient and robust base from which to generate statistically representative synthetic microstructures for use in multi-scale modeling or machine learning applications to support advanced manufacturing and materials discovery.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructure-Based Modeling of Laser Beam Shaping During Additive Manufacturing

Recent experimental studies suggest the use of spatially extended laser beam profiles as a strategy to control the melt pool during laser powder bed fusion (LPBF) additive manufacturing. However, linkages connecting laser beam profiles to thermal fields and resultant microstructures have not been established. Herein, we employ a coupled thermal transport-Monte Carlo model to predict the evolution of temperature fields and grain microstructures during LPBF using Gaussian, ring, and Bessel beam profiles. In addition, simulation results reveal that the ring-shaped beam yields lower temperatures compared with the Gaussian beam. Owing to the small melt pool size when using the Bessel beam, the grains are smaller in size and more equiaxed compared to those using the Gaussian and ring beams. Our approach provides future avenues to predict the impact of laser beam shaping on microstructure development during LPBF.

36 MATERIALS SCIENCE↗