Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ignition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Comparisons between thermodynamic and one-dimensional combustion models of spark-ignition engines

Results from a one-dimensional combustion model employing a constant eddy diffusivity and a one-step chemical reaction are compared with those of one-zone and two-zone thermodynamic models to study the flame propagation in a spark-ignition engine. One-dimensional model predictions are found to be very sensitive to the eddy diffusivity and reaction rate data. The average mixing temperature found using the one-zone thermodynamic model is higher than those of the two-zone and one-dimensional models during the compression stroke, and that of the one-dimensional model is higher than those predicted by both thermodynamic models during the expansion stroke. The one-dimensional model is shown to predict an accelerating flame even when the front approaches the cold cylinder wall.

Ramos, J. I.↗
NASA NTRS1987

Silane as an ignition aid in scramjets

This paper presents the results of experiments on silane/hydrogen combustion in a scramjet model configured as a constant area duct with a central injector. Intake flow conditions were created by free piston shock tunnels with simulated flight speeds ranging between 1.4 and 4.2 km/s. Intake conditions were restricted to three nominal Mach numbers. Boundary layer heating appeared to be responsible for ignition at low temperature, high Mach number conditions. Concentration of silane in hydrogen was varied, as well as intake temperature and pressure. Results indicated that silane in concentrations as low as 2.5 percent in hydrogen, was effective as a fuel additive for scramjets at conditions where hydrogen alone could not support combustion. An unsteady effect was observed as the intake temperature approached the lower limit for combustion. The combustion temperature limit rose significantly as the intake pressure was reduced to low levels. Computer simulations using a one dimensional premixed analysis suggested that although silane enhanced the combustion process, it was strongly dependent on the initial concentration of free radical oxygen. Results from the simulations were comparable to experimental results for some conditions.

Morris, N. A.↗
NASA NTRS1988

Evaporation And Ignition Of Dense Fuel Sprays

Simple theoretical model makes useful predictions of trends. Pair of reports presents theoretical model of evaporation and ignition of sprayed liquid fuel. Developed as part of research in combustion of oil and liquid fuels derived from coal, tar sand, and shale in furnace. Work eventually contributes to increase efficiency of combustion and decrease pollution generated by burning of such fuels.

Bellan, Josette↗
NASA NTRS1987

The carbon dioxide chaperon efficiency for the reaction H + O2 + M yields HO2 + M from ignition delay times behind reflected shock waves

Ignition delay times for stoichiometric hydrogen-oxygen in argon with and without carbon dioxide were measured behind reflected shock waves. A 20-reaction kinetic mechanism models the measured hydrogen-oxygen delay times over the temperature range 950 to 1300 K. The chaperon efficiency for carbon dioxide determined for the hydrogen-oxygen carbon dioxide mixture was 7.0. This value is in agreement with literature values but much less than a recent value obtained from flow tube experiments. Delay times measured behind a reflected shock wave were about 20% longer than those measured behind incident shock waves. The kinetic mechanism successfully modeled the high-pressure data of Skinner and the hydrogen-air data of Stack. It is suggested that the lowest temperature points for the hydrogen-air data of Slack are unreliable and that the 0.27-atm data may illustrate a case where vibrational relaxation of nitrogen is important. The reaction pathway HO2 yields H2O2 yields OH yields H was required to model the high-pressure data of Skinner. The successful modeling of the stoichiometric hydrogen-air data demonstrates the appropriateness of deriving kinetic models from data for gas mixtures highly diluted with argon. The technique of reducing a detailed kinetic mechanism to only the important reactions for a limited range of experimental data may render the mechanism useless for other test conditions.

Brabbs, Theodore A.↗
NASA NTRS1988

Comparison results for ignition in conjugate systems

The exothermic reaction of an arbitrarily shaped solid in a well-mixed continuous flow of constant density and velocity is investigated analytically, with a focus on a zeroth-order reaction in a pellet. Comparison theorems for the basic problem and the eigenvalue problem of ignition are derived, and the domain dependence of the bifurcation point is explored using the method of Joseph (1976). Some typical analytical results are presented in tables and compared with published values obtained using numerical methods.

Pushpavanam, S.↗
NASA NTRS1986

Determination of the relative resistance to ignition of selected turbopump materials in high-pressure, high-temperature, oxygen environments, volume 1

Advances in the design of the liquid oxygen, liquid hydrogen engines for the Space Transportation System call for the use of warm, high-pressure oxygen as the driving gas in the liquid oxygen turbopump. The NASA Lewis Research Center requested the NASA White Sands Test Facility (WSTF) to design a test program to determine the relative resistance to ignition of nine selected turbopump materials: Hastelloy X, Inconel 600, Invar 36, Monel K-500, nickel 200, silicon carbide, stainless steel 316, and zirconium copper. The materials were subjected to particle impact and to frictional heating in high-pressure oxygen.

Stoltzfus, Joel M.↗
NASA NTRS1989

Improved plasma torch for ignition and flame holding in supersonic combustion

A plasma torch system designed for ignition and flame-holding in supersonic combustion studies has been modified, in order to decrease electrode wear and increase stability, through the incorporation of a flow swirler in the gas inlet that adds vortex-stabilization to the arc. The torch body was redesigned in order to achieve superior alignment of the electrodes; the electrode gap was made continuously adjustable, thereby allowing fine tuning during torch operation. Table operation of the improved torch has been demonstrated in pure nitrogen, eliminating the requirement of argon gas for arc stabilization.

O'Brien, W. F.↗
NASA NTRS1990

Testing Bearing Balls For Ignition In Liquid Oxygen

Inexpensive, safe apparatus built to test cooling by, ignition in, and nucleate boiling to film boiling of liquid oxygen flowing around ball bearings. Provides for heating of bearing specimens, direct observations, and measurements of temperatures and temperature distributions by thermocouples and infrared sensors. Used to evaluate suitability of various materials and surface treatments for ball bearings in high-pressure liquid-oxygen turbopumps. Ball rests in fixture while liquid oxygen flows around it. Flow reversed so observer or infrared sensor can view phenomena on trailing or leading side of ball.

Wagner, William R.↗
NASA NTRS1991

Mixing, ignition and combustion studies using discrete orifice injection at hypervelocity flight conditions

Testing at hypervelocity test conditions continues in the Hypulse expansion tube. A newly-calibrated Mach 13 operating point has been achieved, and hydrogen injection studies were performed at this test condition. The experiments were conducted in a 2-in x 1-in combustor model employing three injector configurations: a single flush-wall circular orifice; two such orifices on opposite walls (the 'dual' injector configuration); and two orifices on the upper and the lower walls (the 'quad' injector configuration). The quad injectors were distinctly superior to the other two configurations in promoting mixing, ignition, and combustion. The single injector, however, proved to be superior to the dual injectors, supporting the concept that the aspect ratio of the 'injection cell' plays a large role in promoting the processes required to achieve high combustion efficiency.

Bakos, R.↗
NASA NTRS1991

Numerical analysis of ignition transients in solid rocket motors

A model to analyze the unstready multidimensional turbulent flow in the head-end, star slot section of a solid rocket motor during the ignition transient is developed. The present paper examines the fluid dynamic aspects of the starting transient. A finite-difference solution of the unsteady, compressible, full Navier-Stokes equations, together with a two-equation k-epsilon turbulence model, is obtained utilizing the MacCormack explicit, predictor-corrector technique. Computed results for the flow in the slot are compared with experimental data obtained in cold flow tests of a scaled model of the Space Shuttle SRM head-end, star grain section. The agreement between the calculated flowfield and existing experimental data is very good.

Ciucci, A.↗
NASA NTRS1991

Ignition and structure of a laminar diffusion flame in the field of a vortex

The distortion of flames in flows with vortical motion is examined via asymptotic analysis and numerical simulation. The model consists of a constant density, one step, irreversible Arrhenius reaction between initially unmixed species occupying adjacent half-planes which are then allowed to mix and react in the presence of a vortex. The evolution in time of the temperature and mass fraction fields is followed. Emphasis is placed on the ignition time and location as a function of vortex Reynolds number and initial temperature differences of the reacting species. The study brings out the influence of the vortex on the chemical reaction. In all phases, good agreement is observed between asymptotic analysis and the full numerical solution of the model equations.

Macaraeg, Michele G.↗
NASA NTRS1993

Coating Hydrostatic Bearings To Resist Ignition In Oxygen

Coats of superalloy MA754 plasma-sprayed onto occasionally rubbing surfaces of hydrostatic journal bearings operating in liquid and/or gaseous oxygen, according to proposal. Prevents ignition and combustion occurring when components made of stainless steels or other conventional bearing alloys rub against each other in oxygen. Eliminates need for runner and enhances control over critical bearing clearance.

Funkhouser, Merle E.↗
NASA NTRS1993

Laser diode ignition characteristics of Zirconium Potassium Perchlorate (ZPP)

Hi-Shear Technology, Corp., (HSTC) has designed and built a Laser equivalent NASA Standard Initiator (LNSI). Langlie tests with a laser diode output initiating ZPP were conducted as a part of this effort. The test parameters include time to first pressure, laser power density requirements, and ignition time. The data from these laser tests on ZPP are presented.

Callaghan, Jerry D.↗
NASA NTRS1991

Ignition and combustion characteristics of metallized propellants

Over the past six months, experimental investigations were continued and theoretical work on the secondary atomization process was begun. Final shakedown of the sizing/velocity measuring system was completed and the aluminum combustion detection system was modified and tested. Atomizer operation was improved to allow steady state operation over long periods of time for several slurries. To validate the theoretical modeling, work involving carbon slurry atomization and combustion was begun and qualitative observations were made. Simultaneous measurements of aluminum slurry droplet size distributions and detection of burning aluminum particles were performed at several axial locations above the burner. The principle theoretical effort was the application of a rigid shell formation model to aluminum slurries and an investigation of the effects of various parameters on the shell formation process. This shell formation model was extended to include the process leading up to droplet disruption, and previously developed analytical models were applied to yield theoretical aluminum agglomerate ignition and combustion times. The several theoretical times were compared with the experimental results.

Mueller, D. C.↗
NASA NTRS1993

ASRM propellant and igniter propellant development and process scale-up

A program of formulation and process development for ANB-3652 motor propellant was conducted to validate design concepts and screen critical propellant composition and process parameters. Design experiments resulted in the selection of a less active grade of ferric oxide to provide better burning rate control, the establishment of AP fluidization conditions that minimized the adverse effects of particle attrition, and the selection of a higher mix temperature to improve mechanical properties. It is shown that the propellant can be formulated with AP and aluminum powder from various producers. An extended duration pilot plant run demonstrated stable equipment operation and excellent reproducibility of propellant properties. A similar program of formulation and process optimization culminating in large batch scaleup was conducted for ANB-3672 igniter propellant. The results for both ANB-3652 and ANB 37672 confirmed that their processing characteristics are compatible with full-scale production.

Landers, L. C.↗
NASA NTRS1993

2D axisymmetric analysis of SRM ignition transient

To analyze ignition transient of Space Shuttle solid rocket motor, a transient two-dimensional numerical model based on turbulent compressible Navier-Stokes equations in a generalized coordinate system was developed. One-dimensional numerical models (Peretz et al., 1973; Han, 1992; Pardue and Han, 1992) with empirical correlations data obtained from steady turbulent boundary layer flows agrees reasonably well with test rocket data by adjusting a few parameters. However, a 1D model can not provide a physical insight into the complex multidimensional thermal fields and flowfields in the chamber and the converging-diverging rocket nozzle. As an interim step, a 2D model was developed and compared with test data. A modified version of SIMPLE algorithm was used for the numerical model, and the standard k-epsilon model with a wall function was used for turbulence closure. Transient flowfields and thermal fields in the combustion chamber and the attached nozzle were obtained for a selected rocket geometry and propellant. Transient behaviors of the flow and thermal fields were analyzed, and were found to be in good agreement with physical expectations.

Bai, S. D.↗
NASA NTRS1921

Causes of Cracking of Ignition Cable

The experiments described here show that the cracking at sharp bends, observed in the insulation of internal combustion engine high tension ignition wires after service, is due to a chemical attack upon the rubber by the ozone produced by the electric discharge that takes place at the surface of the cable. This cracking does not occur if the insulating material is not under tension, or if the cable is surrounded by some medium other than air. But it does occur even if the insulation is not subjected to electric stress, provided that the atmosphere near the cable contains ozone. The extent of this cracking varies greatly with the insulating material used. The cracking can be materially reduced by using braided cable and by avoiding sharp bends.

Silsbee, F B↗
NASA NTRS1930

Performance of a High-Speed Compression-Ignition Engine Using Multiple Orifice Fuel Injection Nozzles

This report presents test results obtained at the Langley Memorial Aeronautical Laboratory of the National Advisory Committee for Aeronautics during an investigation to determine the relative performance of a single-cylinder, high-speed, compression-ignition engine when using fuel injection valve nozzles with different numbers, sizes, and directions of round orifices. A spring-loaded, automatic injection valve was used, centrally located at the top of a vertical disk-type combustion chamber formed between horizontally opposed inlet and exhaust valves of a 5 inch by 7 inch engine.

Spanogle, J A↗