Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “frequency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Interactive Power to Frequency Dynamics Between Grid-Forming Inverters and Synchronous Generators in Power Electronics-Dominated Power Systems

With increased attention on grid-forming inverters as a power system stabilizing device during high shares of inverter-based resource operations, there is a present need for a transparent and methodical investigation of the inverted and direct power to frequency control capabilities and impacts of these devices on emerging power systems. Here, analysis of the frequency dynamics of the droop-controlled grid-forming inverter and the synchronous generator illuminates the inverted active power-frequency relationship and the frequency response order reduction, forming the basis for novel, nonlinear frequency control approaches. Device-level electromagnetic transient domain simulations corroborate the order-reduction findings, establish that a properly designed dc-side system has a negligible impact on power transfer and will not impede frequency regulation, and confirm the primary frequency response improvement with nonlinear control. Simulations of the 9- and 39-bus test systems validate the order reduction and associated decoupling of the nadir and rate of change of frequency in larger networks. Oscillatory mode analysis confirms the grid-forming benefit of increased damping; decreased damping is observed at shares above 80%, but not at 100%. Finally, simulations on a validated Maui power system model with a 96% of inverter-based resources model yield a trend toward a first-order response.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Encoding Frequency Constraints in Preventive Unit Commitment Using Deep Learning With Region-of-Interest Active Sampling

With the increasing penetration of renewable energy, frequency response and its security are of significant concerns for reliable power system operations. Frequency-constrained unit commitment (FCUC) is proposed to address this challenge. Despite existing efforts in modeling frequency characteristics in unit commitment (UC), current strategies can only handle oversimplified low-order frequency response models and do not consider wide-range operating conditions. This paper presents a generic data-driven framework for FCUC under high renewable penetration. Here, deep neural networks (DNNs) are trained to predict the frequency response using real data or high-fidelity simulation data. Next, the DNN is reformulated as a set of mixed-integer linear constraints to be incorporated into the ordinary UC formulation. In the data generation phase, all possible power injections are considered, and a region-of-interest active sampling is proposed to include power injection samples with frequency nadirs closer to the UFLC threshold, which enhances the accuracy of frequency constraints in FCUC. The proposed FCUC is investigated on the IEEE 39-bus system. Then, a full-order dynamic model simulation using PSS/E verifies the effectiveness of FCUC in frequency-secure generator commitments.

42 ENGINEERING↗

Alternative Approaches for Incentivizing the Frequency Responsive Reserve Ancillary Service

Frequency responsive reserve is the autonomous response of generators and demand response to deviations of system frequency, usually as a result of the instantaneous outage of a large supplier. Frequency responsive reserve arrests the frequency decline resulting in the stabilization of system frequency, and avoids the triggering of under-frequency load-shedding or the reaching of unstablefrequencies that could ultimately lead to system blackouts. It is a crucial service required to maintain a reliable and secure power system. Regions with restructured electricity markets have historically had a lack of incentives for frequency responsive reserve because generators inherently provided the response and on large interconnected systems, more than sufficient response has beenavailable. This may not be the case in future systems due to new technologies and declining response. This paper discusses the issues that can occur without proper incentives and even disincentives, and proposes alternatives to introduce incentives for resources to provide frequency responsive reserve to ensure an efficient and reliable power system.

17 WIND ENERGY↗

Real-Time Wave Energy Converter Control Using Instantaneous Frequency

Wave Energy Converters (WECs) rely on effective Power Take-Off (PTO) control strategies to maximize energy absorption under dynamic sea conditions. Traditional hydrodynamic modeling techniques may require computationally intensive convolution calculations, making real-time control implementation challenging. This paper presents an alternative approach by leveraging instantaneous frequency estimation to dynamically adjust PTO damping in response to varying wave frequencies. Two real-time frequency estimation methods are explored: the Hilbert Transform (HT) and Phase-Locked Loop (PLL). The Hilbert Transform method provides accurate frequency tracking but introduces a delayed response due to its dependence on causal data. Conversely, the PLL approach demonstrates strong potential in frequency tracking but requires careful gain tuning, particularly in complex sea states. Comparative evaluations across multiple test cases—including sinusoidal variations, amplitude steps, frequency step changes, and real-world JONSWAP spectrum waves—highlight the strengths and limitations of each method. The two different PTO control techniques across the various frequency estimation methods were tested under real-sea states using a state-space model of a point-absorbing Wave Energy Converter. The Capture Width Ratio (CWR) is used as a performance metric, with results showing that the HT achieves a 10.6% improvement, while the PLL estimation yields a 0.9% improvement relative to the fixed parameter control baseline. These results highlight the effectiveness of real-time frequency estimation in improving energy absorption compared to static control parameters.

WEC control↗

High-Frequency Signature-Based Fault Detection for Future MV Distribution Grids: Preprint

Increased deployment of Distributed Energy Resources (DERs) and microgrids are significantly changing the operation of distribution grid. Increasing penetration of power electronics based DERs also raise several operational problems such as protection coordination issues, voltage raise, recloser synchronization, stability, and frequency control. Legacy systems are designed for unidirectional power flow. Bidirectional power flows, and varying short circuit levels are some of the major challenges in implementing these legacy protection schemes for future power grid with high penetration of power electronics based DERs. Inverter based DER’s can contribute to a maximum of 2 p.u. fault current. Interconnection standards might require even lower fault current contribution. If these protection related challenges are not addressed, it will result in limiting the penetration of DERs in distribution feeders. In this paper, the feasibility of high frequency signature generated by transients is evaluated to identify and locate faults in a distribution system. The paper will discuss the need for an accurate line modeling approach to accurately capture the high frequency signatures. These high frequency signatures are naturally occurring electromagnetic transients for events such as switching events in the network, faults events, etc. This is different than that implemented in transmission systems as the proposed approach utilizes advanced signal processing techniques to retrieve valuable information from the high frequency signatures generated during faults and does not just rely on time delay measurements between reflections of the high frequency signals. In the full paper, information of a modified IEEE distribution feeder test system to accurately model the high frequency signatures will be provided. The distribution lines will be modeled using universal line modeling (ULM) technique in an electromagnetic transients program (EMTP) modeling platform. Different test cases will be simulated and these test cases will include different fault types, multiple fault locations, capacitor bank switching, etc. The feeder system modeled for these simulations will also include power electronics based DERs. Additionally, experimental results demonstrating the high frequency signatures generated due to a transient event in a medium voltage (13.8 kV) distribution line will also be presented in the full paper. Furthermore, the analysis combined with simulation and experimental results in the full paper will help demonstrate the feasibility and efficacy of the proposed protection scheme. The developed protection scheme will not just help solve problems generated by bidirectional current flow, varying short-circuit current capacity, but also help in proliferation of DERs in distribution systems.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Assessments of data centers for provision of frequency regulation

There are numerous opportunities for data centers to participate in demand response programs considering their large energy capacities, flexible working environments and workloads, redundant design and operation, etc. As a type of demand response, frequency regulation requires fast response, and its potential is not fully explored by data centers yet. This paper proposes a synergistic control strategy for data center frequency regulation which uses both IT and cooling systems. It combines power management techniques at the server level with control of the chilled water supply temperature to track the regulation signal from the electrical market. A frequency regulation flexibility factor is also proposed to increase the IT capacity for frequency regulation. The performance of the control strategy is studied through numerical simulations using an equation based object-oriented Modelica platform designed for data centers. Simulation results show that with well-tuned control parameters, data centers can provide frequency regulation service in both regulation up and down. The performance of data centers in providing frequency regulation service is largely influenced by the regulation capacity bid, frequency regulation flexibility factor, workload condition, and cooling mode of the cooling system, and not significantly influenced by the time constant of chillers. In addition, compared with a server-only control strategy, the proposed synergistic control strategy can provide an extra regulation capacity of 3% of the design power when chillers are activated. Here, when chillers are deactivated, both strategies have a similar regulation capacity.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

High frequency content in nonlinear soil response: A numerical artifact or a reality?

This article probes the reasons for the presence of high frequency components, which are not a part of the input, in the output of nonlinear site response analysis. The nonlinear site response analysis of a single soil element, under a single frequency sinusoidal displacement, is conducted to demonstrate the presence of frequencies higher than the input frequency in the soil element's shear stress and the free surface acceleration. The parameters of this one element problem are chosen carefully to minimize numerical errors. The shape of the stress-strain hysteresis loop is found to be the main cause for the presence of these higher frequencies. A quasi-static problem similar to the direct shear test is then considered to analyze the effect of different hysteresis shapes. Through this analysis, it is numerically and analytically shown that any deviation of the stress-strain hysteresis shape from a perfect ellipse results in output frequencies higher than the input frequency and the number of higher frequencies produced depends on whether the hysteresis shape is smooth or pointed.

42 ENGINEERING↗

Watching Polarons Move in the Energy and Frequency Domains Using Color Impedance Spectroscopy

The hybrid electronic–ionic transport property of π-conjugated polymers enables new (opto)electrochemical device constructs for energy conversion and storage and biosensing applications. One major challenge is separating the energy and frequency dependence of Faradaic events–those involving charge transfer and the redox processes of the conjugated backbone–from the non-Faradaic components, such as ionic motion. Herein, we combine optical spectroscopy with electrochemical impedance spectroscopy (EIS) to resolve the frequency response of ionic–electronic coupling as a function of electrochemical doping potential. First, using EIS, we identify two different frequency regimes resulting in potential-dependent capacitive elements on the order of ~10 μF/cm 2 in a high-frequency regime and ~50–150 μF/cm 2 in a low-frequency regime. Given the larger magnitude and greater potential dependence, we posit that polaronic motion is more likely to occur at low frequencies (<1 kHz) and overlaps with ionic motion. The use of color impedance spectroscopy (CIS) enables observation of polaronic motion with frequency modulation. We observe that higher doping potentials show a greater motion of polarons above the DC-bias baseline concentration for onset in electrochemical doping, but all potentials considered demonstrate a critical frequency at which the polaronic motion is “frozen” (~40 Hz). Furthermore, this critical information obtained from CIS in highly dielectric environments offers a unique figure of merit for future studies on electronic–ionic coupling by which to compare across polymer/electrolyte interfaces, including the role of a charge-supporting electrolyte, a solvent, and alternative Faradaic processes (e.g., electrocatalysis).

36 MATERIALS SCIENCE↗

Low-Frequency Interlayer Raman Modes to Probe Interface of Twisted Bilayer MoS 2

A variety of van der Waals homo- and hetero- structures assembled by stamping monolayers together present optoelectronic properties suitable for diverse applications. Understanding the details of the interlayer stacking and resulting coupling is crucial for tuning these properties. Twisted bilayer transition metal dichalcogenides offer a great platform for developing a precise understanding of the structure/property relationship. Here, we study the low-frequency interlayer shear and breathing Raman modes (<50 cm-1) in twisted bilayer MoS 2 by Raman spectroscopy and first-principles modeling. Twisting introduces both rotational and translational shifts and significantly alters the interlayer stacking and coupling, leading to notable frequency and intensity changes of low-frequency modes. The frequency variation can be up to 8 cm-1 and the intensity can vary by a factor of ~5 for twisting near 0 and 60 , where the stacking is a mixture of multiple high-symmetry stacking patterns and is thus especially sensitive to twisting. Moreover, for twisting angles between 20 and 40 , the interlayer coupling is nearly constant since the stacking results in mismatched lattices over the entire sample. It follows that the Raman signature is relatively uniform. Interestingly, unlike the breathing mode, the shear mode is extremely sensitive to twisting: it disappears between 20 and 40 as its frequency drops to almost zero due to the stacking-induced mismatch. Note that for some samples, multiple breathing mode peaks appear, indicating non-uniform coupling across the interface. In contrast to the low-frequency interlayer modes, high-frequency intralayer Raman modes are much less sensitive to interlayer stacking and coupling, showing negligible changes upon twisting. Our research demonstrates the effectiveness of low-frequency Raman modes for probing the interfacial coupling and environment of twisted bilayer MoS2, and potentially other two-dimensional materials and heterostructures.

36 MATERIALS SCIENCE↗

Quantifying Dam-Induced Fluctuations in Streamflow Frequencies Across the Colorado River Basin

Periodic fluctuations in natural streamflow are a major driver of river ecosystem dynamics and water resource management. However, most U.S. rivers are impacted both by long-term hydroclimatic trends and dams that alter flow variability. Despite these impacts, it remains largely unexplored how dams affect the dominant frequencies of natural streamflow over a highly regulated river network. We investigated the entire Colorado River Basin (CRB) to understand how the annual (10–14 months) and multi-annual (24–60 months) frequencies in natural flow regimes have been progressively altered by dams. Given the significant alteration over the CRB, we captured changes in streamflow frequencies between naturalized and observed monthly flows via wavelet analysis. Based on the similarity of changes in streamflow frequencies (annual and multi-annual) over the last 30 years, sections of the riverine network were classified into four groups. The annual frequency was relatively well preserved downstream of Hoover Dam, while showing a systematic trend of alteration downstream of Glen Canyon Dam until Hoover Dam. Meanwhile, the multi-annual frequency component was highly altered for the entire Lower Colorado main stem (i.e., downstream of Glen Canyon). We also identified dams with significant impacts on streamflow frequency by comparing wavelet coherence estimates. This study advances the notion that dams fundamentally alter river flow regimes across multiple frequencies and with varying amplitudes over time and space, with alteration propagating – or being dampened – by both hydroclimatic fluctuations and water resource management.

54 ENVIRONMENTAL SCIENCES↗

An all-dielectric metasurface as a broadband optical frequency mixer

A frequency mixer is a nonlinear device that combines electromagnetic waves to create waves at new frequencies. Mixers are ubiquitous components in modern radio-frequency technology and microwave signal processing. The development of versatile frequency mixers for optical frequencies remains challenging: such devices generally rely on weak nonlinear optical processes and, thus, must satisfy phase-matching conditions. Here we utilize a GaAs-based dielectric metasurface to demonstrate an optical frequency mixer that concurrently generates eleven new frequencies spanning the ultraviolet to near-infrared. The even and odd order nonlinearities of GaAs enable our observation of second-harmonic, third-harmonic, and fourth-harmonic generation, sum-frequency generation, two-photon absorption-induced photoluminescence, four-wave mixing and six-wave mixing. The simultaneous occurrence of these seven nonlinear processes is assisted by the combined effects of strong intrinsic material nonlinearities, enhanced electromagnetic fields, and relaxed phase-matching requirements. In conclusion, such ultracompact optical mixers may enable a plethora of applications in biology, chemistry, sensing, communications, and quantum optics.

47 OTHER INSTRUMENTATION↗

Influence of driving frequency on discharge modes in a dielectric-barrier discharge with multiple current pulses

A one-dimensional self-consistent fluid model was employed to investigate the effect of the driving frequency on the discharge modes in atmospheric-pressure argon discharge with multiple current pulses. The discharge mode was discussed in detail not only at current peaks but also between two adjacent peaks. The simulation results show that different transitions between the Townsend and glow modes during the discharge take place with the driving frequency increased. A complicated transition from the Townsend mode, through glow, Townsend, and glow, and finally back to the Townsend one is found in the discharge with the driving frequency of 8 kHz. There is a tendency of transition from the Townsend to glow mode for the discharge both at the current peaks and troughs with the increasing frequency. The discharge in the half period can all along operate in the glow mode with the driving frequency high enough. This is resulted from the preservation of more electrons in the gas gap and acquisition of more electron energy from the swiftly varying electric field with the increase in driving frequency. Comparison of the spatial and temporal evolutions of the electron density at different driving frequencies indicates that the increment of the driving frequency allows the plasma chemistry to be enhanced. This electrical characteristic is important for the applications, such as surface treatment and biomedical sterilization.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Dependence of the colored frequency noise in spin torque oscillators on current and magnetic field

The nano-scale spin torque oscillator (STO) is a compelling device for on-chip, highly tunable microwave frequency signal generation. Currently, one of the most important challenges for the STO is to increase its longer-time frequency stability by decreasing the 1/f frequency noise, but its high level makes even its measurement impossible using the phase noise mode of spectrum analyzers. Here, we present a custom made time-domain measurement system with 150 MHz measurement bandwidth making possible the investigation of the variation of the 1/f as well as the white frequency noise in a STO over a large set of operating points covering 18–25 GHz. The 1/f level is found to be highly dependent on the oscillation amplitude-frequency non-linearity and the vicinity of unexcited oscillation modes. These findings elucidate the need for a quantitative theoretical treatment of the low-frequency, colored frequency noise in STOs. Based on the results, we suggest that the 1/f frequency noise possibly can be decreased by improving the microstructural quality of the metallic thin films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

An inkjet vision measurement technique for high-frequency jetting

Inkjet technology has been used as manufacturing a tool for printed electronics. To increase the productivity, the jetting frequency needs to be increased. When using high-frequency jetting, the printed pattern quality could be non-uniform since the jetting performance characteristics including the jetting speed and droplet volume could vary significantly with increases in jet frequency. Therefore, high-frequency jetting behavior must be evaluated properly for improvement. However, it is difficult to measure high-frequency jetting behavior using previous vision analysis methods, because subsequent droplets are close or even merged. In this paper, we present vision measurement techniques to evaluate the drop formation of high-frequency jetting. The proposed method is based on tracking target droplets such that subsequent droplets can be excluded in the image analysis by focusing on the target droplet. Finally, a frequency sweeping method for jetting speed and droplet volume is presented to understand the overall jetting frequency effects on jetting performance.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Emission in the ion cyclotron range of frequencies (ICE) on NSTX and NSTX-U

We report here on observations of magnetic fluctuations in the ion-cyclotron frequency range on NSTX and NSTX-U. In many respects, the fluctuations appear similar to the ion cyclotron emission (ICE) seen in conventional tokamaks. However, a significant difference between previous observations of ICE and the ICE on NSTX is that the frequency of ICE in conventional tokamaks is typically near the ion cyclotron frequency of the energetic fast ions at the plasma edge. In NSTX and NSTX-U, the magnetic fluctuation frequency corresponds to the ion cyclotron frequency deeper in the plasma, near the location of an internal transport barrier. As on conventional tokamaks, higher harmonics of the deuterium cyclotron frequency, as high as the seventh, are seen with the strongest signal sometimes from higher harmonics. The emission usually appears as an irregular sequence of short bursts typically ≤100 μs in duration although nearly continuous emission for several ms has also been seen under some conditions. Measurements of the emission with a toroidal array of fast probes show that the emission is a long wavelength, spatially coherent mode. The emission frequency does not follow an Alfvénic scaling with density, as seen for compressional Alfvén eigenmodes, but does show a linear scaling with local magnetic field strength. The measured emission shows a compressional polarization consistent with a compressional Alfvén wave. No correlation between the neutron rate and the ICE amplitude is seen. In conclusion, three-wave coupling between the instability responsible for the ICE and lower frequency modes has also been observed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Theory of Alfvén-slow frequency gaps and discovery of Alfvén-slow eigenmodes in tokamaks

An analytical theory based on the MHD model is presented for understanding the coupling between the shear Alfvén wave and the slow magnetosonic wave (or the so called slow mode) in the frequency range below the Toroidal Alfvén Eigenmode (TAE) continuum spectrum gap. In tokamak plasmas, coupling of the Alfvén m poloidal harmonic and the slow mode m ± 1 harmonics causes the Alfvén m harmonic continuous spectrum to be uplifted from the uncoupled Alfvén spectrum by an amount related to the plasma pressure and the geodesic magnetic field curvature. However, the frequency of one of the slow mode m ± 1 harmonics is reduced by the same pressure-curvature coupling effect. But the frequency of the other slow mode harmonic is relatively unaffected. As a result, the Alfvén-slow (AS) mode continuous spectrum is broken up into two Alfvén-Slow (AS) gaps below the TAE continuum gap. Coupling of the Alfvén m harmonic with the slow mode m ± 2 harmonics also creates additional AS gaps if their frequencies cross each other. The AS gap widths increase with the plasma pressure. The creation of AS gaps allows the existence of several new types of Alfvén-Slow Eigenmodes (ASEs). The radial structure of these new ASEs does not intersect with the continuous spectrum and thus does not suffer from continuum damping. The Beta-induced Alfvén-Acoustic Eigenmode (BAAE) is one type of ASEs with frequency in the lowest AS frequency gap. However, the BAAE usually interacts with the Alfvén-Slow continuum and suffers from continuum damping. The existence of ASEs is ubiquitous for normal and reserve safety factor profiles, broad range of plasma β values, different plasma shapes, and many different toroidal mode numbers. The newly discovered ASEs provide explanation for the experimentally observed Beta-induced Alfvén Eigenmodes destabilized by fast ions with frequencies below the TAE frequency gap.

Cheng, C. Z. (ORCID:0000000166187806)↗

High frequency impedance characteristics of a tunable microplasma device

Computational studies on high frequency impedance characteristics of a microplasma device are reported. While microplasma is ignited using a primary excitation signal, frequency response of plasma impedance is determined by a secondary high frequency probe signal with significantly lower voltage amplitude such that it does not influence the plasma parameters. Here, the computational model utilizing the drift–diffusion approximation is first validated by comparing with experimental data for microplasmas ignited at pressures ranging from 1 to 5 Torr. In spite of quantitative discrepancies, good overall agreement is obtained between the measured frequency response of impedance of the discharge. Comparisons are also presented for various plasma parameters including mean electron number density, sheath thickness, mean electron temperature, and collision frequency that were inferred from the impedance measurements. The computational model is then used to perform simulations of near-atmospheric pressure microplasmas with the probe signal frequency ranging from 3 to 20 GHz. The simulations demonstrate the presence of a resonance frequency at which the impedance vanishes. More importantly, it is shown that this resonant frequency can be tuned effectively by suitably modifying the operating parameters (gap size, pressure, and excitation voltage). The simulated impedance characteristics are used to determine the effective plasma inductance and capacitance using a non-linear fitting approach, thereby showing the dependence of these electrical parameters on the plasma operating conditions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

THE ACOUSTIC CUTOFF FREQUENCY OF THE SUN AND THE SOLAR MAGNETIC ACTIVITY CYCLE

The acoustic cutoff frequency-the highest frequency for acoustic solar eigenmodes-is an important parameter of the solar atmosphere as it determines the upper boundary of the p-mode resonant cavities. At frequencies beyond this value, acoustic disturbances are no longer trapped but are traveling waves. Interference among them gives rise to higher-frequency peaks-the pseudomodes-in the solar acoustic spectrum. The pseudomodes are shifted slightly in frequency with respect to p-modes, making possible the use of pseudomodes to determine the acoustic cutoff frequency. Using data from the GOLF and VIRGO instruments on board the Solar and Heliospheric Observatory spacecraft, we calculate the acoustic cutoff frequency using the coherence function between both the velocity and intensity sets of data. By using data gathered by these instruments during the entire lifetime of the mission (1996 until the present), a variation in the acoustic cutoff frequency with the solar magnetic activity cycle is found.

79 ASTRONOMY AND ASTROPHYSICS↗