Results for “dynamic load testing” — Page 29

NASA NTRSDate not supplied

Advanced Modeling of Control-Structure Interaction in Thrust Vector Control Systems

The Space Launch System (SLS) Core Stage (CS) Thrust Vector Control (TVC) system is comprised of 8 mechanical feedback Shuttle heritage Type III TVC actuators and four RS-25 engines, each attached to a Shuttle heritage gimbal block/bearing. Two actuators are used to move each engine in two planes perpendicular to one another (i.e., pitch and yaw). The TVC system design leverages hardware from the Space Shuttle program as well as new hardware designed specifically for the Core Stage. During the development of the SLS TVC system, a family of advanced dynamics models were developed to extend and compliment the simplified quasi-linear “simplex” model historically used for flight control design and stability analysis. The importance of these advanced models became increasingly evident after ambient and hot fire testing of the Core Stage, which revealed a number of findings associated with the dynamic response of the TVC integrated system. Test responses suggested that the TVC did not meet its performance specifications and its step and frequency responses exhibited unexpected departures from prior lab tests and modeled behavior. One driving factor for these results was a higher-than-expected degree of coupling between the TVC system, the engine dynamics, and the Core Stage structure. This paper is the third installment in a seven-paper series surveying the design, engineering, test validation, and flight performance of the Core Stage Thrust Vector Control system. In this paper, a new method of modeling rocket vehicle thrust vectoring servoelastic dynamics is presented. In this approach, the load dynamics are replaced by a detailed finite element model containing both the rigid body and elastic modes. A partitioning technique is used to compute the effective compliance from the modal data and obtain accurate simulation results using a reduced number of generalized coordinates. Coupled backup structure and nozzle attach compliance effects on multiple engines are captured in higher fidelity than with a spring approximation, eliciting novel effects due to the complex load paths involved in the Core Stage structure. Validation of the model is demonstrated using a variety of structural/modal, laboratory, and full-scale hot fire test data.

Launch Vehicles↗

NASA NTRSDate not supplied

Advanced Modeling of Control-Structure Interaction in Thrust Vector Control Systems

The Space Launch System (SLS) Core Stage (CS) Thrust Vector Control (TVC) system is comprised of 8 mechanical feedback Shuttle heritage Type III TVC actuators and four RS-25 engines, each attached to a Shuttle heritage gimbal block/bearing. Two actuators are used to move each engine in two planes perpendicular to one another (i.e., pitch and yaw). The TVC system design leverages hardware from the Space Shuttle program as well as new hardware designed specifically for the Core Stage. During the development of the SLS TVC system, a family of advanced dynamics models were developed to extend and compliment the simplified quasi-linear “simplex” model historically used for flight control design and stability analysis. The importance of these advanced models became increasingly evident after ambient and hot fire testing of the Core Stage, which revealed a number of findings associated with the dynamic response of the TVC integrated system. Test responses suggested that the TVC did not meet its performance specifications and its step and frequency responses exhibited unexpected departures from prior lab tests and modeled behavior. One driving factor for these results was a higher-than-expected degree of coupling between the TVC system, the engine dynamics, and the Core Stage structure. This paper is the third installment in a seven-paper series surveying the design, engineering, test validation, and flight performance of the Core Stage Thrust Vector Control system. In this paper, a new method of modeling rocket vehicle thrust vectoring servoelastic dynamics is presented. In this approach, the load dynamics are replaced by a detailed finite element model containing both the rigid body and elastic modes. A partitioning technique is used to compute the effective compliance from the modal data and obtain accurate simulation results using a reduced number of generalized coordinates. Coupled backup structure and nozzle attach compliance effects on multiple engines are captured in higher fidelity than with a spring approximation, eliciting novel effects due to the complex load paths involved in the Core Stage structure. Validation of the model is demonstrated using a variety of structural/modal, laboratory, and full-scale hot fire test data.

Launch Vehicles↗

NASA NTRS2022

Mars 2020 Perseverance Rover SHERLOC Instrument Isolation System

The NASA Jet Propulsion Laboratory (JPL) successfully landed the Mars 2020 Perseverance Rover at Jezero Crater on the Martian surface. Perseverance’s main mission objective is to cache Martian rock and regolith samples in hermetically sealed tubes to be brought back to Earth by future missions. To achieve this goal the rover is equipped with a 2-meter-long Robotic Arm (RA) which manipulates the Turret to interact with the surface. The Turret is comprised of science instruments and tools that enable surface sampling and science. The backbone of the Turret hardware is the Rotary Percussive Coring Drill. The science instruments, which are directly mounted to the structural housing of this drill, must be able to withstand not only the launch and entry, descent and landing (EDL) loads of the vehicle but also the dynamic percussive environment, induced by the drill throughout surface operations. This paper discusses the technical hardware design, development and testing of a vibration isolation system to protect the Scanning Habitable Environments with Raman and Luminescence for Organics and Chemicals (SHERLOC) Instrument from these dynamic environments. The hardware design aspect of this problem was limited by both size and mass constraints. The Turret is tightly configured and the physical space in which hardware can reside is restricted due to multiple axes of surface interaction points. Another driving requirement is the extreme range of thermal non-operational environment from -135C to +90C. This, in addition to SHERLOC being a heavier instrument than previously integrated on a turret, made the use of isolation systems employed on previous rover missions problematic. The final design incorporates custom wire mesh springs preloaded within titanium hexapod struts equipped with flexure ends. Custom versions of commercially available wire mesh springs were designed and tested. These custom springs differed in dimension, density and stiffness from the off the shelf options. The newly designed springs went through various stages of flight acceptance testing. Detailed physics-based modeling to understand what loads the isolation system would experience was used to define the test conditions for the springs and entire isolation subsystem. The testing program developed around this was extensive to fully characterize the isolation performance over cleanliness levels, temperature and life. Another major aspect of this work was developing a method of replicating the drill’s percussive environment for performance and life testing of Turret mounted hardware. Attaching the instrument to an operating drill for testing was not a viable option. A method of using a Highly Accelerated Life Test (HALT) table was developed and applied across the project as the most representative and tunable option to physically simulate this new environment. This method, along with launch environment random vibration testing, was used to build an entire dynamic qualification and flight hardware test program. The results of the design, modeling, testing and analysis of the SHERLOC Isolation System is described throughout the following paper.

Krafchak, Todd↗

DOE OSTI2022

Low cost and massively parallel force spectroscopy with fluid loading on a chip

Current approaches for single molecule force spectroscopy are typically constrained by low throughput and high instrumentation cost. Herein, a low-cost, high throughput technique is demonstrated using microfluidics for multiplexed mechanical manipulation of up to ~4000 individual molecules via molecular fluid loading on-a-chip (FLO-Chip). The FLO-Chip consists of serially connected microchannels with varying width, allowing for simultaneous testing at multiple loading rates. Molecular force measurements are demonstrated by dissociating Biotin-Streptavidin and Digoxigenin-AntiDigoxigenin interactions along with unzipping of double stranded DNA of varying sequence under different dynamic loading rates and solution conditions. Rupture force results under varying loading rates and solution conditions are in good agreement with prior studies, verifying a versatile approach for single molecule biophysics and molecular mechanobiology. FLO-Chip enables straightforward, rapid, low-cost, and portable mechanical testing of single molecules that can be implemented on a wide range of microscopes to broaden access and may enable new applications of molecular force spectroscopy.

42 ENGINEERING↗

NASA NTRS1988

Stiffnesses of a solid-rocket motor from an ambient vibration survey

Experience with many spacecraft configurations boosted by a variety of launch vehicles indicates that the maximum loads experienced throughout most of the structure are inertial in origin. These loads arise from the dynamic elastic response of the flight vehicle to the transient disturbances of launch and flight, and are highly dependent on the dynamic characteristics of both the spacecraft and the launch vehicle. It has proved to be most advantageous, in the analysis of this critical dependency of loads upon vehicle dynamic properties, to establish a mathematical model in terms of normal mode characteristics. In this way, the vibration behavior of an elastomechanical structure (or substructure) can be described by means of the so-called modal or natural degrees of freedom. The conduct of a mode survey test and the use of a suitably test-verified model in loads analyses is essential to the flight worthiness certification process of space systems. The desirability of such tests is confirmed by the fact that, almost invariably, significant deficiencies in the analytical models are revealed by the results. Therefore, this experimental program was undertaken to determine those properties of a solid-propellant rocket motor (SRM) which are required to characterize a dynamic model. Random ambient-excited accelerations were measured at a series of stations along the motor for the purpose of identifying the motor beam-like stiffnesses in bending, shear, and torsion. From a system identification point of view, it is significant that stiffness properties of a subsystem (the motor) are determined from modes of the full system (motor/stand configuration) using mode shape data of the subsystem only. This contrasts with traditional system identification approaches which rely upon complete system mode shapes.

Rubin, S.↗

NASA NTRS2001

Temperature Dependent Modal Test/Analysis Correlation of X-34 Fastrac Composite Rocket Nozzle

A unique high temperature modal test and model correlation/update program has been performed on the composite nozzle of the FASTRAC engine for the NASA X-34 Reusable Launch Vehicle. The program was required to provide an accurate high temperature model of the nozzle for incorporation into the engine system structural dynamics model for loads calculation; this model is significantly different from the ambient case due to the large decrease in composite stiffness properties due to heating. The high-temperature modal test was performed during a hot-fire test of the nozzle. Previously, a series of high fidelity modal tests and finite element model correlation of the nozzle in a free-free configuration had been performed. This model was then attached to a modal-test verified model of the engine hot-fire test stand and the ambient system mode shapes were identified. A reduced set of accelerometers was then attached to the nozzle, the engine fired full-duration, and the frequency peaks corresponding to the ambient nozzle modes individually isolated and tracked as they decreased during the test. To update the finite-element model of the nozzle to these frequency curves, the percentage differences of the anisotropic composite moduli due to temperature variation from ambient, which had been used in the initial modeling and which were obtained by small sample coupon testing, were multiplied by an iteratively determined constant factor. These new properties were used to create high-temperature nozzle models corresponding to 10 second engine operation increments and tied into the engine system model for loads determination.

Brown, Andrew M.↗

NASA NTRS1979

Experimental study of acoustic loads on an upper-surface-blown STOL airplane configuration

Fluctuating pressure levels were measured on the flap and fuselage of an upper-surface-blown jet-flap airplane configuration in a wind tunnel. The model tested had turbofan engines with a bypass ratio of 3 and a thrust rating of 10 kN. Rectangular nozzles were mounted flush with the upper surface at 35 percent of the wing chord. Test parameters were flap deflection angle, jet impingement angle, angle of attack, free-stream velocity, spanwise location of the engine, and jet dynamic pressure. Load levels were high throughout the jet impingement region, with the highest levels (about 159 dB) occurring on the fuselage and near the knee of the flap. The magnitude of the forward-velocity effect appeared to depend upon the ratio of free-stream and jet velocities. Good agreement was obtained between fluctuating pressure spectra measured at jet dynamic pressures of 7 and 22 kPa when the spectra were scaled by nondimensional functions of dynamic pressure, velocity, and the empirical relationship between dynamic pressure and overall fluctuating pressure level.

Willis, C. M.↗

NASA NTRSDate not supplied

Adaptive Control and Scaling Approach for the Emulation of Dynamic Sub-scale Torque Loads

Previous research by the authors proposed a control and scaling approach for emulating dynamic sub-scale torque loads. This approach produced an emulation controller that successfully regulated the dynamic behavior of a sub-scale electro-mechanical system intended to be a dynamical representation of the sub-scale turboelectric powertrain of a single-aisle commercial aircraft. The sub-scale system provides an environment without turbomachinery or rotors for the initial testing of electrified aircraft propulsion (EAP) control algorithms as they would be applied to a full-scale EAP system. The sub-scale turbomachinery/rotor torque loads were produced by electric machines (EMs) driven by the control and scaling approach, a full-scale turboelectric powertrain model, and an advanced EAP control algorithm. Although successfully tested, this approach produces an emulation controller that does not guarantee asymptotic stability. Modifying the original control law and integrating adaptive control techniques into the emulation controller allows the designer to guarantee asymptotic stability. This paper introduces the idea behind the emulation controller modifications, derives the controller, proves asymptotic stability, describes the implementation of the controller on a sub-scale electro-mechanical system intended to represent a parallel hybrid-electric turbofan engine, and describes the testing of a full-scale advanced EAP control algorithm. The turbofan engine and emulation controller performance are compared to results obtained using the previous, non-adaptive control and scaling approach.

adaptive↗

NASA NTRSDate not supplied

Adaptive Control and Scaling Approach for the Emulation of Dynamic Subscale Torque Loads

Previous research by the authors proposed a control and scaling approach for emulating dynamic sub-scale torque loads. This approach produced an emulation controller that successfully regulated the dynamic behavior of a sub-scale electro-mechanical system intended to be a dynamical representation of the sub-scale turboelectric powertrain of a single-aisle commercial aircraft. The sub-scale system provides an environment without turbomachinery or rotors for the initial testing of electrified aircraft propulsion (EAP) control algorithms as they would be applied to a full-scale EAP system. The sub-scale turbomachinery/rotor torque loads were produced by electric machines (EMs) driven by the control and scaling approach, a full-scale turboelectric powertrain model, and an advanced EAP control algorithm. Although successfully tested, this approach produces an emulation controller that does not guarantee asymptotic stability. Modifying the original control law and integrating adaptive control techniques into the emulation controller allows the designer to guarantee asymptotic stability. This paper introduces the idea behind the emulation controller modifications, derives the controller, proves asymptotic stability, describes the implementation of the controller on a sub-scale electro-mechanical system intended to represent a parallel hybrid-electric turbofan engine, and describes the testing of a full-scale advanced EAP control algorithm. The turbofan engine and emulation controller performance are compared to results obtained using the previous, non-adaptive control and scaling approach.

adaptive↗

NASA NTRS2019

Static Torsion Testing and Modeling of a Variable Thickness Hybrid Composite Bull Gear

Torsional strength of a variable thickness hybrid gear web was measured by performing static testing on the part in a large torsion test frame. The outer rim of the hybrid gear web was fixed to the bottom of the test frame and loading was applied to the web through a shaft. The test setup included the installation of digital image correlation (DIC) systems to obtain deformation and strain measurements from the surfaces of the hybrid gear web and the mechanical test equipment to ensure reliability of the test. The results indicated that the variable thickness hybrid gear web achieved approximately twice the torsional strength compared to that of previous hybrid gear designs. The DIC analysis showed significantly more straining of the loading shaft than the actual test article. Additionally, the results demonstrated the importance and affect that the metallic, lobed interlock features had on the principal strain and out-of-plane displacement fields. The analysis revealed that the fixed outer rim was in fact rotating and a rigid body motion compensation (RBMC) function was computed to determine the actual rotation of the hub and composite web relative to the outer rim. Modeling simulations were performed for the variable thickness hybrid gear web and correlated well with the RBMC rotational deformation seen in the DIC analysis. In addition to benchmarking the load capacity of the hybrid gear web, measuring its strength is useful information to define the parameters needed for dynamic, endurance, and other testing of the part.

Johnston, Joel P.↗

NASA NTRS1999

Damage Tolerance Issues as Related to Metallic Rotorcraft Dynamic Components

In this paper issues related to the use of damage tolerance in life managing rotorcraft dynamic components are reviewed. In the past, rotorcraft fatigue design has combined constant amplitude tests of full-scale parts with flight loads and usage data in a conservative manner to provide "safe life" component replacement times. In contrast to the safe life approach over the past twenty years the United States Air Force and several other NATO nations have used damage tolerance design philosophies for fixed wing aircraft to improve safety and reliability. The reliability of the safe life approach being used in rotorcraft started to be questioned shortly after presentations at an American Helicopter Society's specialist meeting in 1980 showed predicted fatigue lives for a hypothetical pitch-link problem to vary from a low of 9 hours to a high in excess of 2594 hours. This presented serious cost, weight, and reliability implications. Somewhat after the U.S. Army introduced its six nines reliability on fatigue life, attention shifted towards using a possible damage tolerance approach to the life management of rotorcraft dynamic components. The use of damage tolerance in life management of dynamic rotorcraft parts will be the subject of this paper. This review will start with past studies on using damage tolerance life management with existing helicopter parts that were safe life designed. Also covered will be a successful attempt at certifying a tail rotor pitch rod using damage tolerance, which was designed using the safe life approach. The FAA review of rotorcraft fatigue design and their recommendations along with some on-going U.S. industry research in damage tolerance on rotorcraft will be reviewed.

Everett, R. A., Jr.↗

NASA NTRS2005

Damage Tolerance Issues as Related to Metallic Rotorcraft Dynamic Components

In this paper issues related to the use of damage tolerance in life managing rotorcraft dynamic components are reviewed. In the past, rotorcraft fatigue design has combined constant amplitude tests of full-scale parts with flight loads and usage data in a conservative manner to provide "safe life" component replacement times. In contrast to the safe life approach over the past twenty years the United States Air Force and several other NATO nations have used damage tolerance design philosophies for fixed wing aircraft to improve safety and reliability. The reliability of the safe life approach being used in rotorcraft started to be questioned shortly after presentations at an American Helicopter Society's specialist meeting in 1980 showed predicted fatigue lives for a hypothetical pitch-link problem to vary from a low of 9 hours to a high in excess of 2594 hours. This presented serious cost, weight, and reliability implications. Somewhat after the U.S. Army introduced its six nines reliability on fatigue life, attention shifted towards using a possible damage tolerance approach to the life management of rotorcraft dynamic components. The use of damage tolerance in life management of dynamic rotorcraft parts will be the subject of this paper. This review will start with past studies on using damage tolerance life management with existing helicopter parts that were safe life designed. Also covered will be a successful attempt at certifying a tail rotor pitch rod using damage tolerance, which was designed using the safe life approach. The FAA review of rotorcraft fatigue design and their recommendations along with some on-going U.S. industry research in damage tolerance on rotorcraft will be reviewed. Finally, possible problems and future needs for research will be highlighted.

Everett, R. A., Jr.↗

NASA NTRS1983

Parametric tip effects for conformable rotor applications

A research study was initiated to systematically determine the impact of selected blade tip geometric parameters on aeroelasticity conformable rotor performance and loads characteristics. The model articulated rotors included baseline and torsionally soft blades with interchangeable tips. Seven blade tip designs were evaluated on the baseline rotor and three tip designs were tested on the torsionally soft blades. The designs incorporated a systematic variation in three geometric parameters: sweep, taper, and anhedral. The rotors were evaluated in the NASA Langley Transonic Dynamics Tunnel at several advance ratios, lift and propulsive force values, and tip Mach numbers. Based on the test results, tip parameter variations generated significant rotor performance and loads difference for both baseline and torsionally soft blades. Azimuthal variation of elastic twist generated by the tip parameters strongly correlated with rotor performance and loads, but the magnitude of advancing blade elastic twist did not correlate.

Mantay, W. R.↗

NASA NTRS2018

Investigation of Multi-Input, Multi-Output (MIMO) Random Control Applied to Direct Field Acoustic Testing

Direct Field Acoustic Testing (DFAT) offers potential cost and time savings over reverberant chamber acoustic testing of spacecraft. The NASA Multi-Purpose Crew Vehicle (MPCV) Program recently directed a series of acoustic tests on Orion structural test articles comparing DFAT and reverberant testing of the same test article with a view to qualifying DFAT for manned space flight vehicles. The verification process compared four parameters noise level compliance with the one third octave test specification, spatial uniformity of the acoustic field, spatial correlation of the acoustic field and vibration response of vehicle structure, including representative solar array panels. While the results of the verification were encouraging, MPCV Loads and Dynamics engaged Quartus Engineering to investigate whether alternative MIMO random control strategies might improve the spatial uniformity and/or the spatial correlation of the DFAT acoustic field. This paper presents the results of acoustic field simulations of the DFAT test and provides a better understanding of how MIMO random control systems originally developed for vibration and structural durability testing can be expected to perform in DFAT testing.

Direct Field↗

NASA NTRS2012

The Effect of Systematic Error in Forced Oscillation Testing

One of the fundamental problems in flight dynamics is the formulation of aerodynamic forces and moments acting on an aircraft in arbitrary motion. Classically, conventional stability derivatives are used for the representation of aerodynamic loads in the aircraft equations of motion. However, for modern aircraft with highly nonlinear and unsteady aerodynamic characteristics undergoing maneuvers at high angle of attack and/or angular rates the conventional stability derivative model is no longer valid. Attempts to formulate aerodynamic model equations with unsteady terms are based on several different wind tunnel techniques: for example, captive, wind tunnel single degree-of-freedom, and wind tunnel free-flying techniques. One of the most common techniques is forced oscillation testing. However, the forced oscillation testing method does not address the systematic and systematic correlation errors from the test apparatus that cause inconsistencies in the measured oscillatory stability derivatives. The primary objective of this study is to identify the possible sources and magnitude of systematic error in representative dynamic test apparatuses. Sensitivities of the longitudinal stability derivatives to systematic errors are computed, using a high fidelity simulation of a forced oscillation test rig, and assessed using both Design of Experiments and Monte Carlo methods.

Williams, Brianne Y.↗

DOE OSTI2021

Fast GPU-Based Generation of Large Graph Networks From Degree Distributions

Synthetically generated, large graph networks serve as useful proxies to real-world networks for many graph-based applications. The ability to generate such networks helps overcome several limitations of real-world networks regarding their number, availability, and access. Here, we present the design, implementation, and performance study of a novel network generator that can produce very large graph networks conforming to any desired degree distribution. The generator is designed and implemented for efficient execution on modern graphics processing units (GPUs). Given an array of desired vertex degrees and number of vertices for each desired degree, our algorithm generates the edges of a random graph that satisfies the input degree distribution. Multiple runtime variants are implemented and tested: 1) a uniform static work assignment using a fixed thread launch scheme, 2) a load-balanced static work assignment also with fixed thread launch but with cost-aware task-to-thread mapping, and 3) a dynamic scheme with multiple GPU kernels asynchronously launched from the CPU. The generation is tested on a range of popular networks such as Twitter and Facebook, representing different scales and skews in degree distributions. Results show that, using our algorithm on a single modern GPU (NVIDIA Volta V100), it is possible to generate large-scale graph networks at rates exceeding 50 billion edges per second for a 69 billion-edge network. GPU profiling confirms high utilization and low branching divergence of our implementation from small to large network sizes. For networks with scattered distributions, we provide a coarsening method that further increases the GPU-based generation speed by up to a factor of 4 on tested input networks with over 45 billion edges.

97 MATHEMATICS AND COMPUTING↗

NASA NTRS1983

Flutter and steady/unsteady aerodynamic characteristics of supercritical and conventional transport wings

This paper presents the technical details and results of a high-speed wind-tunnel test program of an aeroelastic cantilevered transport type wing with two pylon-mounted engines. The tests were conducted in the NASA-Langley 16-foot Transonic Dynamic tunnel (TDT) during December 1981. Flutter of identical planforms, mass properties, and stiffness. The test parameters included different values of model stiffness and wing loading at various angles of attack. The models were instrumented at span-wise wing stations to determine bending and torsion deflections and vertical accelerations. At two model wing stations, pressure transducers were distributed along the chord to record static and unsteady oscillatory pressures during the approach to and onset of flutter. This paper presents the test program with results of the flutter characteristics and selected steady and unsteady aerodynamic data for both airfoils at different angles of attack for various Mach numbers and dynamic pressures.

Grosser, W. F.↗

NASA NTRSDate not supplied

Experimental Methods Using Force Application of A Single Boom for A 500-M²-Class Solar Sail

Solar sailing missions rely on deployable systems for large area-to-mass ratios once in space, while still being small enough for launcher envelopes in the stowed configuration. Many of these deployable systems feature booms that are flattened and subsequently coiled onto a spool / hub. As part of a collaborative deployable space structures research effort between the National Aeronautics and Space Administration (NASA) and German Aerospace Center (DLR), a boom deployment system for a future 500 m² solar sail has been developed. To achieve the respective solar sail size goal, 16.5-m-long booms produced by NASA were integrated into a DLR-designed deployer mechanism. This considerable size, as well as the lightweight construction of the booms and respective deployable systems makes testing on the ground a significant challenge. Some systems for gravity compensation as well as vertical testing to minimize the influence of gravity have been used in the past. However, an uncertainty factor remains towards the behaviour in the space environment. The focus of this paper is the load application testing of the integrated boom-deployment mechanism system under microgravity condition, as well as a comparison to vertical testing under gravity. Testing in microgravity was performed during a parabolic flight test inside an aircraft and it included stowage and full deployment of a single boom along the longitudinal axis of the aircraft. The load application was split into two categories: static testing, which induced a linear force ramp to the static boom for either compression or compression-bending; and dynamic testing, which applied a constant force to a boom during extension provided by the deployer mechanism. Both types of tests were performed multiple times at two distinct lengths of the boom, fully deployed (12.76 m) and ~28.6 % deployed (3.65 m). More parameters that are vital to the test philosophy are the angles of attack in the force application and the highest force applied. The data acquisition used for the applied load and deflection measurements of the boom is also presented.

Martin Richter↗