Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “defect passivation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Nanoporous silica gel structures and evolution from reactive force field-based molecular dynamics simulations

Nanoporous silica-rich gel formed on silicate glass surfaces during dissolution in aqueous environment is critical in elucidating the corrosion mechanisms and the long-term residual dissolution behaviors. Silica gel models were created using two types of methods with reactive force field-based molecular dynamics simulations. The results show that the remnant silica gels created from the ISG bulk structure have a more isolated and closed pore morphology and slightly higher glass network connectivity. This contrasts with the gel structures created by hydrogarnet defect formation that exhibit more connected pore morphologies. The remnant gel structures show lower water diffusivity which was explained by the nano-confinement effect of water molecules due to frequent interactions of water molecules with adjacent silica walls and the more isolated pore morphology in the remnant gel structures. These results reveal the complexity in terms of micro and atomic structures of these silica gels, and both structure features have impact on water transport in the gel layer hence the passivating effect that controls the long-term dissolution behavior of these glasses.

36 MATERIALS SCIENCE↗

Passive directional sub-ambient daytime radiative cooling

Demonstrations of passive daytime radiative cooling have primarily relied on complex and costly spectrally selective nanophotonic structures with high emissivity in the transparent atmospheric spectral window and high reflectivity in the solar spectrum. Here, we show a directional approach to passive radiative cooling that exploits the angular confinement of solar irradiation in the sky to achieve sub-ambient cooling during the day regardless of the emitter properties in the solar spectrum. We experimentally demonstrate this approach using a setup comprising a polished aluminum disk that reflects direct solar irradiation and a white infrared-transparent polyethylene convection cover that minimizes diffuse solar irradiation. Measurements performed around solar noon show a minimum temperature of 6 °C below ambient temperature and maximum cooling power of 45 W m –2 . Our passive cooling approach, realized using commonly available low-cost materials, could improve the performance of existing cooling systems and enable next-generation thermal management and refrigeration solutions.

14 SOLAR ENERGY↗

Evaluation of Low-Pressure-Sintered Multi-Layer Substrates for Medium-Voltage SiC Power Modules: Preprint

Direct-bonded aluminum (DBA) multi-layer substrates have been fabricated using low-pressure silver sintering. These multi-layer substrates can be used to reduce the peak electric field strength inside power modules. This benefit is particularly important for medium-voltage silicon carbide (SiC) MOSFETs due to their higher operating voltages. The voiding content and defect density of the bond used to create the multi-layer substrate stackup is critical to the thermal performance and reliability of the power module. This work two low-pressure-assisted sintering techniques; one using nano-silver preform and the other using nano-silver paste to bond 23 mm by 49 mm DBA substrates. Scanning acoustic microscopy (C-SAM) is used to evaluate the bond quality after sintering. To evaluate the reliability of the sintered multi-layer substrates, passive thermal cycling from –40 °C to 200 °C was performed. Cross-sections were cut at pre-determined intervals and imaged with Scanning Electron Microscopy (SEM). After 1,000 thermal cycles, minor cracking was observed, but no failures have occurred.

28 EE - Advanced Manufacturing Office (EE-5A)↗

Enhanced photoelectrochemical performance of rutile TiO{sub 2} by Sb-N donor-acceptor coincorporation from first principles calculations

An effective non-metal (N) and non-transition metal (Sb) passivated co-doping approach is proposed to improve the photoelectochemical performance of rutile TiO{sub 2} for water-splitting by using first-principles calculations. It is found that the band edges of N + Sb co-doped TiO{sub 2} match with the redox potentials of water, and a narrow band gap (2.0 eV) is achieved for enhanced visible light absorption. The compensated donor (Sb) and acceptor (N) pairs could prevent the recombination of photo-generated electron-hole pairs. In addition, the N + Sb defect pairs tend to bind with each other, which could enhance the stability and N concentration of the system.

36 MATERIALS SCIENCE↗

On the relationship between non-stoichiometry and passivity breakdown in ultra-thin oxides: combined depth-dependent spectroscopy, Mott-Schottky analysis and molecular dynamics simulation studies

Understanding the relationship between non-stoichiometry and physical properties of ultra-thin oxides is of great importance from both scientific and technological aspects. A specific example includes the onset of passivity breakdown in an ultra-thin oxide film in aqueous medium leading to the onset of corrosion. In this work, using the model system of ultra-thin oxide of alumina on aluminum synthesized by natural oxidation and photon-assisted oxidation processes; we demonstrate a direct correlation between passivity and quality of the oxide film quantitatively. Depth-dependent high resolution X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) and nuclear reaction analysis (NRA) have been performed to characterize the physical and chemical properties of the oxide films, while detailed impedance measurements and Mott-Schottky studies have been performed to understand electronic transport. Combined NRA and TEM analysis reveal an 18% increase in oxygen density (for oxide films with near identical thicknesses ~3.8nm) in case of photon-assisted oxidation. The denser oxide film results in a ~34% more blockage of chloride ions transport as indicated by XPS analysis. Mott Schottky measurements on these oxide films indicates a 43% reduction of defect levels for UV-synthesized alumina when compared to native one, suggestive of chloride ion transport via oxygen vacancies. Additionally, molecular dynamics simulations have been performed to provide insights into the structure of the oxides at the atomic level to correlate with the experimental measurements. These simulations employ dynamic charge transfer between atoms and are used to investigate nanoscale oxides grown on Al (100) surfaces due to atomic and molecular oxygen. Oxidation using molecular and atomic oxygen resulted in an amorphous oxide scale with self limiting thickness of ~ 16 and 22 Å, respectively at 300 K. Structural and dynamic correlations indicate significant charge transfer to exist in the oxide film in both the cases. The oxide growth in both the cases occurs due to the inward oxygen and outward cation diffusion. The calculated in-plane and out-of-plane atomic diffusivities are 40-70% higher in case of atomic oxidation. In the presence of atomic oxygen, the O/Al ratio is more uniform and varies from 1.37 at the oxide-gas interface to 1.30 at metal-oxide interface whereas that formed by natural oxidation was sub-stoichiometric and oxygen deficient with O/Al values varying from 1.27 (oxide-gas interface) to 1.05 (metal-oxide interface) at room temperature. The simulation results are consistent with the reported experimental investigations.

36 MATERIALS SCIENCE↗

Pitting behavior of friction stir repair-welded 304L stainless steel in 3.5% NaCl solution at room temperature: role of grain and defect structures

Stainless steel (SS) canisters used for storing spent nuclear waste are prone to chloride-induced stress corrosion cracking. Friction stir welding (FSW), being a low heat input process, can be used for repair welding of these canisters. In this study, an artificial crack was introduced on the 304L SS coupons by an electric discharge machining process. The artificial crack was repair-welded by FSW by maintaining the tool temperature a constant at two levels (725 and 825 °C). Friction stirring significantly reduced the grain size of the stirred zone (SZ) from about 47 to 2–4 μm. The fraction of low-angle grain boundaries increased in the SZ from 2 to 37–43%. Here, on the other hand, the fraction of special grain boundaries (Σ3 and Σ9) that was ~ 50% in the base metal reduced to < 10% in the SZ. During friction stirring, the oxide layer of artificial crack was broken and aligned to form a spiral defect called lazy-S structure. All these microstructural changes affected the corrosion behavior of the FSW specimens when tested in 3.5% NaCl at room temperature using cyclic polarization, chronoamperometry, and electrochemical impedance spectroscopy. The FSW specimens showed lower polarization resistance and lower transpassive potential than those of the base metal specimens. However, the pitting protection potentials of the FSW specimens were higher than that of the base metal. The pitting behavior of the FSW specimens was influenced more by the preferential attack on the lazy-S region than by passive film breakdown. The flat band potentials of the passive film formed on the FSW specimens were more positive than that of base metal. The charge carrier density of passive film formed on the FSW specimens was higher than that of the base metal. The higher fraction of low-angle grain boundaries present in the FSW specimens could supply more number of misorientation dislocations at the metal/film interface which could form anion vacancies by a climb process leading to formation of oxide at these locations without stressing the substrate. Therefore, low-angle boundaries are considered helpful for formation of stress-free passive films that will be highly stable and enhance both pitting and stress corrosion cracking resistance.

Dry storage canister↗

Perovskite grain wrapping by converting interfaces and grain boundaries into robust and water-insoluble low-dimensional perovskites

Stabilizing perovskite solar cells requires consideration of all defective sites in the devices. Substantial efforts have been devoted to interfaces, while stabilization of grain boundaries received less attention. Here, we report on a molecule tributyl(methyl)phosphonium iodide (TPI), which can convert perovskite into a wide bandgap one-dimensional (1D) perovskite that is mechanically robust and water insoluble. Mixing TPI with perovskite precursor results in a wrapping of perovskite grains with both grain surfaces and grain boundaries converted into several nanometer-thick 1D perovskites during the grain formation process as observed by direct mapping. The grain wrapping passivates the grain boundaries, enhances their resistance to moisture, and reduces the iodine released during light soaking. The perovskite films with wrapped grains are more stable under heat and light. The best device with wrapped grains maintained 92.2% of its highest efficiency after light soaking under 1-sun illumination for 1900 hours at 55°C open-circuit condition.

14 SOLAR ENERGY↗

Achieving designed texture and flows in bulk active nematics using optimal control theory

Being intrinsically nonequilibrium, active materials can potentially perform functions that would be thermodynamically forbidden in passive materials. However, active systems have diverse local attractors that correspond to distinct dynamical states, many of which exhibit chaotic turbulent-like dynamics and thus cannot perform work or useful functions. Designing such a system to choose a specific dynamical state is a formidable challenge. Motivated by recent advances enabling optogenetic control of experimental active materials, we describe an optimal control theory framework that identifies a spatiotemporal sequence of light-generated activity that drives an active nematic system toward a prescribed dynamical steady state. Active nematics are unstable to spontaneous defect proliferation and chaotic streaming dynamics in the absence of control. We demonstrate that optimal control theory can compute activity fields that redirect the dynamics into a variety of alternative dynamical programs and functions. This includes dynamically reconfiguring between states, selecting and stabilizing emergent behaviors that do not correspond to attractors, and are hence unstable in the uncontrolled system. Furthermore, our results provide a roadmap to leverage optical control methods to rationally design structure, dynamics, and function in a wide variety of active materials.

Complex systems theory↗

Upgraded metallurgical-grade silicon solar cells with efficiency above 20%

We present solar cells fabricated with n-type Czochralski–silicon wafers grown with strongly compensated 100% upgraded metallurgical-grade feedstock, with efficiencies above 20%. The cells have a passivated boron-diffused front surface, and a rear locally phosphorus-diffused structure fabricated using an etch-back process. The local heavy phosphorus diffusion on the rear helps to maintain a high bulk lifetime in the substrates via phosphorus gettering, whilst also reducing recombination under the rear-side metal contacts. The independently measured results yield a peak efficiency of 20.9% for the best upgraded metallurgical-grade silicon cell and 21.9% for a control device made with electronic-grade float-zone silicon. The presence of boron-oxygen related defects in the cells is also investigated, and we confirm that these defects can be partially deactivated permanently by annealing under illumination.

36 MATERIALS SCIENCE↗

Experimental Evaluation of Fatigue Damage Progression in Postbuckled Single Stringer Composite Specimens

The durability and damage tolerance of postbuckled composite structures are not yet completely understood, and remain difficult to predict due to the nonlinearity of the geometric response and its interaction with local damage modes. A research effort was conducted to investigate experimentally the quasi-static and fatigue damage progression in a single-stringer compression (SSC) specimen. Three specimens were manufactured with a hat-stiffener, and an initial defect was introduced with a Teflon film embedded between one flange of the stringer and the skin. One of the specimens was tested under quasi-static compressive loading, while the remaining two specimens were tested by cycling in postbuckling. The tests were performed at the NASA Langley Research Center under controlled conditions and with instrumentation that allows a precise evaluation of the postbuckling response and of the damage modes. Three-dimensional digital image correlation VIC-3D systems were used to provide full field displacements and strains on the skin and the stringer. Passive thermal monitoring was conducted during the fatigue tests using an infrared camera that showed the location of the delamination front while the specimen was being cycled. The live information from the thermography was used to stop the fatigue tests at critical stages of the damage evolution to allow detailed ultrasonic scans.

Bisagni, Chiara↗

Effects of grain boundaries on conversion efficiencies of single-crystal-like GaAs thin-film solar cells on flexible metal tapes

We present a numerical simulation study of the effects of low-angle grain boundaries (GBs) in a single-crystal-like GaAs thin-film material on its photovoltaic performance. Here, 1D and 2D modeling are employed to simulate a solar-cell (SC) device based on the properties of single-crystal-like GaAs thin films grown on metal tape. Properties include minority carriers’ mobility, carrier lifetimes, and diffusion length. The 1D model, by incorporating a uniform biaxially textured GaAs compared to single crystal GaAs, predicts an efficiency ~21% for average carrier lifetimes of 1 ns. This result is not consistent with an experimental results showing an efficiency of 4.3%. 1D simulation generally works well for the prediction of conventional crystalline SC I-V characteristics, but it fails for newly-developed single-crystal-like GaAs SC devices with different material properties and non-vertical device geometry. Hence, we develop a 2D model to study the effect of localized recombination centers in the material by defining different regions of defective low-angle grain boundaries and single crystalline intra-grains. The 2D model is comparable to the experimental results mainly due to its capability to consider localized material inhomogeneity and lateral carriers dynamic. The effect of grain boundary density on SC performance is studied by 2D modeling. Increasing the grain size of GaAs from 2 μm to 50 μm can improve efficiency from 4.8% to 12.3%. The open-circuit voltage (Voc) shows more sensitivity to varying grain boundary densities than other SC characteristic factors. The 2D model is also employed to study bulk passivation of GBs and suggests that an efficiency of ~19.5% is achievable in the single-crystal-like GaAs SCs even with a small grain size of 2 μm, if effective grain boundary passivation is applied.

14 SOLAR ENERGY↗

Tetracene Functionalized Si(111) Achieves Enhanced Solar-to-Chemical Energy Conversion via Molecular Acceptor States

The properties of semiconductor|liquid interfaces play a critical role in determining the efficiency of solar-to-hydrogen (STH) conversion. Here, we investigate how molecular functionalization of Si(111) and Si(111)|TiO 2 surfaces impacts photoelectrochemical (PEC) hydrogen production efficiency. We find that functionalization of ∼3% of the atop sites of Si(111) with either 9-anthracene (Anth) or 5-tetracene (Tet), with the remaining sites passivated by methyl groups, provides substrates with high electronic quality and low surface oxide densities, as determined by X-ray photoelectron spectroscopy (XPS) measurements. Surface photovoltage (SPV) spectroscopy shows that surfaces modified with Anth or Tet exhibit an increased photovoltage, with Tet-functionalized surfaces yielding an additional 192 meV relative to methyl-terminated Si(111), indicating improved charge separation for Si-Tet. Further improvement in onset potential was achieved by replacing a nitrogen-containing TiO 2 atomic layer deposition (ALD) precursor (TDMAT) with a precursor lacking nitrogen (TTIP), which eliminates the parasitic defect band in the TiO 2 overlayer (p-Si(111)-Tet|TTIP-TiO 2 |Pt: V OC = +0.283 ± 0.041 V vs RHE). Density functional theory (DFT) analysis demonstrates that compared with Anth-modified Si(111), the Tet-modified surface exhibits more hybridized Si(111)-Tet states closer to the silicon band edges. Mercury contact current–voltage (I–V, dark) measurements quantified the relative interfacial density of states of Si-Tet, Si-Anth and Si-Me surfaces─revealing that the interfacial state density was highest for Si-Tet. This suggests that such hybridized interfaces serve to capture better photoexcited charge, which enables facile electron transfer to molecular acceptors in solution. Altogether, the data indicate that beneficial hybrid molecular LUMO surface states interacting with the Si conduction band edge results in improved hydrogen evolution (HER) performance for p-Si devices.

Group theory↗

Self-powered perovskite photon-counting detectors

Metal-halide perovskites (MHPs) have been successfully exploited for converting photons to charges or vice versa in applications of solar cells, light-emitting diodes and solar fuels for which all these applications involve strong light. Here we show that self-powered polycrystalline perovskite photodetectors can rival the commercial silicon photomultipliers (SiPMs) for photon counting. The photon-counting capability of perovskite photon-counting detectors (PCDs) is mainly determined by shallow traps, despite that deep traps also limit charge-collection efficiency. Two shallow traps with energy depth of 5.8 ± 0.8 millielectronvolts (meV) and 57.2 ± 0.1 meV are identified in polycrystalline methylammonium lead triiodide, which mainly stay at grain boundaries and the surface, respectively. We show that these shallow traps can be reduced by grain-size enhancement and surface passivation using diphenyl sulfide, respectively. It greatly suppresses dark count rate (DCR) from >20,000 counts per second per square millimetre (cps mm –2 ) to 2 cps mm –2 at room temperature, enabling much better response to weak light than SiPMs. The perovskite PCDs can collect γ-ray spectra with better energy resolution than SiPMs and maintain performance at high temperatures up to 85 °C. The zero-bias operation of perovskite detectors enables no drift of noise and detection property. Finally, this study opens a new application of photon counting for perovskites that uses their unique defect properties.

47 OTHER INSTRUMENTATION↗

Technical Assessment of the Passive Neutron Enrichment Meter (PNEM) for an Unattended Cylinder Verification Station (UCVS)

The International Atomic Energy Agency (IAEA) is exploring the potential roles of an Unattended Cylinder Verifications Station (UCVS) in a new generation of safeguards technology for uranium enrichment plants. The UCVS is envisioned to combine an operator accountancy scale, a nondestructive assay (NDA) system such as the Passive Neutron Enrichment Meter (PNEM), a cylinder identification system, and a surveillance system for verification of product, feed, and tails cylinders as well as continuity of knowledge at material balance area boundaries. The IAEA has identified several preliminary requirements and development questions for the UCVS. Specifically, the IAEA has identified the accuracy of the enrichment assay as the key metric for the NDA system with uncertainty targets of 3%, 6%, and 9% on product, feed, and tails cylinders, respectively. The NDA system should also provide full volume interrogation of the cylinders in order to ensure detection of partial defects within the cylinder. The development questions are concerned primarily with the sources and magnitude of the uncertainty and quantitative analysis of the interrogation depth and partial defect sensitivity. The objective of this report is to address these requirements and questions based on Monte Carlo modeling and field trial experience with the PNEM.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Safety Aspects of Dry Spent Fuel Storage and Spent Fuel Management - 13559

Dry storage systems are characterized by passive and inherent safety systems ensuring safety even in case of severe incidents or accidents. After the events of Fukushima, the advantages of such passively and inherently safe dry storage systems have become more and more obvious. As with the storage of all radioactive materials, the storage of spent nuclear fuel (SF) and high-level radioactive waste (HLW) must conform to safety requirements. Following safety aspects must be achieved throughout the storage period: - safe enclosure of radioactive materials, - safe removal of decay heat, - securing nuclear criticality safety, - avoidance of unnecessary radiation exposure. The implementation of these safety requirements can be achieved by dry storage of SF and HLW in casks as well as in other systems such as dry vault storage systems or spent fuel pools, where the latter is neither a dry nor a passive system. Furthermore, transport capability must be guaranteed during and after storage as well as limitation and control of radiation exposure. The safe enclosure of radioactive materials in dry storage casks can be achieved by a double-lid sealing system with surveillance of the sealing system. The safe removal of decay heat must be ensured by the design of the storage containers and the storage facility. The safe confinement of radioactive inventory has to be ensured by mechanical integrity of fuel assembly structures. This is guaranteed, e.g. by maintaining the mechanical integrity of the fuel rods or by additional safety measures for defective fuel rods. In order to ensure nuclear critically safety, possible effects of accidents have also to be taken into consideration. In case of dry storage it might be necessary to exclude the re-positioning of fissile material inside the container and/or neutron moderator exclusion might be taken into account. Unnecessary radiation exposure can be avoided by the cask or canister vault system itself. In Germany dry storage of SF in casks fulfills both transport and storage requirements. Mostly, storage facilities are designed as concrete buildings above the ground, but due to regional constraints, one storage facility has also been built as a rock tunnel. The decay heat is always removed by natural air flow; further technical equipment is not needed. The removal of decay heat and shielding had been modeled and calculated by state-of-the-art computer codes before such a facility has been built. TueV and BAM present their long experience in the licensing process for sites and casks and inform about spent nuclear fuel management and issues concerning dry storage of spent nuclear fuel. Different storage systems and facilities in Germany, Europe and world-wide are compared with respect to the safety aspects mentioned above. Initial points are the safety issues of wet storage of SF, and it is shown how dry storage systems can ensure the compliance with the mentioned safety criteria over a long storage period. The German storage concept for dry storage of SF and HLW is presented and discussed. Exemplarily, the process of licensing, erection and operation of selected German dry storage facilities is presented. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Non-metallic dopant modulation of conductivity in substoichiometric tantalum pentoxide: A first-principles study

Here, we apply density-functional theory calculations to predict dopant modulation of electrical conductivity (σ o ) for seven dopants (C, Si, Ge, H, F, N, and B) sampled at 18 quantum molecular dynamics configurations of five independent insertion sites into two (high/low) baseline references of σo in amorphous Ta 2 O 5 , where each reference contains a single, neutral O vacancy center (V O 0 ). From this statistical population (n = 1260), we analyze defect levels, physical structure, and valence charge distributions to characterize nanoscale modification of the atomistic structure in local dopant neighborhoods. C is the most effective dopant at lowering Ta 2 O x σ o , while also exhibiting an amphoteric doping behavior by either donating or accepting charge depending on the host oxide matrix. Both B and F robustly increase Ta 2 O x σ o , although F does so through elimination of Ta high charge outliers, while B insertion conversely creates high charge O outliers through favorable BO 3 group formation, especially in the low σ o reference. While N applications to dope and passivate oxides are prevalent, we also found that N exacerbates the stochasticity of σ o we sought to mitigate; sensitivity to the N insertion site and some propensity to form N-O bond chemistries appear responsible. Finally, we use direct first-principles predictions of σ o to explore feasible Ta 2 O 5 dopants to engineer improved oxides with lower variance and greater repeatability to advance the manufacturability of resistive memory technologies.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Terrestrial Sources of X-Ray Radiation and Their Effects on NASA Flight Hardware

X-rays are an energetic and penetrating form of ionizing electromagnetic radiation, which can degrade NASA flight hardware. The main concern posed by such radiation is degradation of active electronic devices and, in some cases, diodes. Non-electronic components are only damaged at doses that far exceed the point where any electronic device would be destroyed. For the purposes of this document, flight hardware can be taken to mean an entire instrument, the flight electronics within the instrument or the individual microelectronic devices in the flight electronics. This document will discuss and describe the ways in which NASA flight hardware might be exposed to x-rays, what is and isn't a concern, and how to tell the difference. First, we must understand what components in flight hardware may be vulnerable to degradation or failure as a result of being exposed to ionizing radiation, such as x-rays. As stated above, bulk materials (structural metals, plastics, etc.) are generally only affected by ionizing radiation at very high dose levels. Likewise, passive electronic components (e.g. resistors, capacitors, most diodes) are strongly resistant to exposure to x-rays, except at very high doses. The main concerns arise when active components, that is, components like discrete transistors and microelectronic devices, are exposed to ionizing radiation. Active components are designed to respond to minute changes in currents and voltages in the circuit. As such, it is not surprising that exposure to ionizing radiation, which creates ionized and therefore electrically active particles, may degrade the way the hardware performs. For the most part, the mechanism for this degradation is trapping of the charges generated by ionizing radiation by defects in dielectric materials in the hardware. As such, the degree of damage is a function of both the quantity of ionizing radiation exposure and the physical characteristics of the hardware itself. The metric that describes the level of exposure to ionizing radiation is total ionizing dose (TID). The unit of TID is the rad, which is defined as 100 ergs absorbed per gram of material. Dose can be expressed in other units, for example grays (gy), where 1 gy = 100 rads. The actual fluence of radiation needed to deliver a rad depends on the absorbing material, so units of dose are usually stated in reference to the material of interest. That is, for microelectronic devices, the unit of dose is generally rad (Si) or rad (SiO2). However, the definition of absorbed dose in this fashion has the advantage that the type of radiation causing the ionization can be normalized so that a realistic and adequate comparison can be made. The sensitivity of microelectronic parts to TID varies over many orders of magnitude. (Note: Doses to humans are typically expressed in rems-or roentgen-equivalent-man-which measures tissue damage, and depends on the type of radiation, as well as the dose in rads.) Thus far, the "softest" parts tested at NASA showed damage at 500 rads (Si), while parts that are radiation-hardened by design can remain functional to doses on the order of 107 rads (Si). This broad range of sensitivity highlights one of the most important considerations when considering the effects of radiation on electronic parts: In order to determine whether a radiation exposure is a concern for a particular part, one must understand the technologies used in the part and their vulnerabilities to TID damage. A NASA radiation expert should be consulted to obtain such information.

X-ray↗

Effect of erbium fluoride doping on the photoluminescence of SiO{sub x} films

The photoluminescence of SiO{sub x} films deposited on c-Si wafers by the thermal evaporation of SiO in a vacuum and, for the first time, doped with ErF{sub 3} by coevaporation is studied. It is shown that, like undoped SiO{sub x} films, the unannealed SiO{sub x}:ErF{sub 3} films passivate the surface of the Si wafers and, thus, increase their edge photoluminescence intensity almost fivefold. A similar increase is observed after annealing of the doped films in air at 750 Degree-Sign C. Doping with ErF{sub 3} suppresses the photoluminescence of Si nanoclusters, if the films have been subjected to high-temperature annealing (at 750 Degree-Sign C). In this case, the PL intensity of the band with a peak at {approx}890 nm decreases as well. The {approx}890 nm band is observed for the first time and, due to its features, is attributed to transitions in SiO{sub x} matrix defects. The experimentally observed effect of ErF{sub 3} doping on SiO{sub x} film photoluminescence is interpreted. An intense photoluminescence signal from Er{sup 3+} ions in the nearinfrared spectral region (the {sup 4}I{sub 11/2} {yields} {sup 4}I{sub 15/2} and {sup 4}I{sub 13/2} {yields} {sup 4}I{sub 15/2} transitions) is observed in the SiO{sub x}:ErF{sub 3} films annealed in air at 750 Degree-Sign C. This finding shows that 1.54 {mu}m luminescent emitters, which are currently in popular demand, can be produced by a simple low-cost method.

36 MATERIALS SCIENCE↗